Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

USE OF THE SDO POINTING CONTROLLERS FOR INSTRUMENT CALIBRATION MANEUVERS

During the science phase of the Solar Dynamics Observatory mission, the three science instruments require periodic instrument calibration maneuvers with a frequency of up to once per month. The command sequences for these maneuvers vary in length from a handful of steps to over 200 steps, and individual steps vary in size from 5 arcsec per step to 22.5 degrees per step. Early in the calibration maneuver development, it was determined that the original attitude sensor complement could not meet the knowledge requirements for the instrument calibration maneuvers in the event of a sensor failure. Because the mission must be single fault tolerant, an attitude determination trade study was undertaken to determine the impact of adding an additional attitude sensor versus developing alternative, potentially complex, methods of performing the maneuvers in the event of a sensor failure. To limit the impact to the science data capture budget, these instrument calibration maneuvers must be performed as quickly as possible while maintaining the tight pointing and knowledge required to obtain valid data during the calibration. To this end, the decision was made to adapt a linear pointing controller by adjusting gains and adding an attitude limiter so that it would be able to slew quickly and still achieve steady pointing once on target. During the analysis of this controller, questions arose about the stability of the controller during slewing maneuvers due to the combination of the integral gain, attitude limit, and actuator saturation. Analysis was performed and a method for disabling the integral action while slewing was incorporated to ensure stability. A high fidelity simulation is used to simulate the various instrument calibration maneuvers.

Vess, Melissa F.↗
NASA NTRSDate not supplied

Analysis of MSL/MEDLI Entry Data with Coupled CFD and Material Response

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heatshield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers outstanding performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP) [2]. The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on OpenFOAM (PATO) [4,5,6] using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA [7], is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Thermal Protection Systems↗
NASA NTRSDate not supplied

Assessment of Coupling One-Dimension and Three-Dimension CFD in Conjugate Heat Transfer Modeling and Simulations for Cooling of Turbine Engine

The CHT (conjugate heat transfer) modeling and simulation work fits under a bigger area in the TTT (Transformational Tools and Technologies) project called “Cooling Tools and Technologies for Combustor and Turbine.” The existing validation data sets such as TTT GRC (Glenn Research Center) THX (Turbulent Heat FLUX) IV experiments will be used to assess the solid/fluid heat transfer development and validation. The experimental configuration was a subsonic convergent nozzle with a square exit blowing a heated exhaust over an effusion-cooled deck. The simulation solutions were obtained and compared to experimental measurements of the profiles of flow velocities and temperatures, as well as deck surface temperatures. Cooling air blowing ratios of 0, 1, and 2 were considered. The three-dimensional cooling tubes were modelled by the medial axis of the cylindrical geometries due to large length over width ratios. It represented a typical coupling of one-dimension and three-dimension simulations of conjugate heat transfer approaches. The surface temperatures on the solid surfaces and the profiles of velocities and temperatures near the surfaces compared to the experimental data were presented.

nonlinear sub-filter stresses↗
DOE OSTI2026

Data and Code for: Observation-constrained agroecosystem model inversion reveals continental-scale variation of winter wheat traits

This repository contains the simulation outputs and processing scripts associated with the study of winter wheat traits across the United States, utilizing the Ecosys agroecosystem model. The dataset includes model results for both rainfed and irrigated winter wheat systems, supporting the findings presented in the manuscript titled "Observation-constrained agroecosystem model inversion reveals continental-scale variation of winter wheat traits." Data includes the original Ecosys simulation outputs (archived in .db format within the compressed .zip files) and extracted analysis data (stored in .pkl files for efficient processing). Python code for data processing and figure generation is provided in a Jupyter notebook. External Observational Datasets should refer to the following official repositories for the input and validation data used in this study. The eddy covariance data from the AmeriFlux network (https://ameriflux.lbl.gov/). Climate-forcing data of NLDAS-2 from NASA LDAS (https://ldas.gsfc.nasa.gov/nldas/nldas-2-forcing-data). Soil data from the Gridded Soil Survey Geographic Database (gSSURGO), available at (https://www.nrcs.usda.gov/resources/data-and-reports/gridded-soil-survey-geographic-gssurgo-database). Crop yields, planting and harvest dates from the USDA public databases (https://quickstats.nass.usda.gov/; https://webapp.rma.usda.gov/apps/actuarialinformationbrowser/CropCriteria.aspx). Satellite-derived SLOPE GPP data from ORNL DAAC (https://daac.ornl.gov/cgi-bin/dsviewer.pl?ds_id=1786). Land use and crop progress information from the USDA Crop Data Layer and Crop Progress and Condition Gridded Layers (https://www.nass.usda.gov/Research_and_Science/). The Ecosys model code is available online at https://github.com/jinyun1tang/ECOSYS.

Wheat↗
NASA NTRS1996

Analysis of the ACTS-Vancouver Path Propagation Data

The data described here cover the two-year period from 1 December 1993 to 30 November, 1995. The analysis is done for two sets of valid data: (a) observed or total attenuation data, which includes all atmospheric effects plus the additional attenuation resulting from wet antenna surfaces during rain events, and (b) adjusted attenuation data as in (a) minus estimated values of attenuation due to wetting the antenna surfaces. In both cases, average and worst month cumulative distribution functions (CDF's), fade-duration statistics, and fade-slope statistics for the 20 and 27 GHz beacons are presented.

Kharadly, M.↗
NASA NTRS2004

Strategy Developed for Selecting Optimal Sensors for Monitoring Engine Health

Sensor indications during rocket engine operation are the primary means of assessing engine performance and health. Effective selection and location of sensors in the operating engine environment enables accurate real-time condition monitoring and rapid engine controller response to mitigate critical fault conditions. These capabilities are crucial to ensure crew safety and mission success. Effective sensor selection also facilitates postflight condition assessment, which contributes to efficient engine maintenance and reduced operating costs. Under the Next Generation Launch Technology program, the NASA Glenn Research Center, in partnership with Rocketdyne Propulsion and Power, has developed a model-based procedure for systematically selecting an optimal sensor suite for assessing rocket engine system health. This optimization process is termed the systematic sensor selection strategy. Engine health management (EHM) systems generally employ multiple diagnostic procedures including data validation, anomaly detection, fault-isolation, and information fusion. The effectiveness of each diagnostic component is affected by the quality, availability, and compatibility of sensor data. Therefore systematic sensor selection is an enabling technology for EHM. Information in three categories is required by the systematic sensor selection strategy. The first category consists of targeted engine fault information; including the description and estimated risk-reduction factor for each identified fault. Risk-reduction factors are used to define and rank the potential merit of timely fault diagnoses. The second category is composed of candidate sensor information; including type, location, and estimated variance in normal operation. The final category includes the definition of fault scenarios characteristic of each targeted engine fault. These scenarios are defined in terms of engine model hardware parameters. Values of these parameters define engine simulations that generate expected sensor values for targeted fault scenarios. Taken together, this information provides an efficient condensation of the engineering experience and engine flow physics needed for sensor selection. The systematic sensor selection strategy is composed of three primary algorithms. The core of the selection process is a genetic algorithm that iteratively improves a defined quality measure of selected sensor suites. A merit algorithm is employed to compute the quality measure for each test sensor suite presented by the selection process. The quality measure is based on the fidelity of fault detection and the level of fault source discrimination provided by the test sensor suite. An inverse engine model, whose function is to derive hardware performance parameters from sensor data, is an integral part of the merit algorithm. The final component is a statistical evaluation algorithm that characterizes the impact of interference effects, such as control-induced sensor variation and sensor noise, on the probability of fault detection and isolation for optimal and near-optimal sensor suites.

Source record↗
NASA NTRS2023

Probabilistic Forecasting of Ground Magnetic Perturbation Spikes at Mid-Latitude Stations

The prediction of large fluctuations in the ground magnetic field (dB/dt) is essential for preventing damage from Geomagnetically Induced Currents. Directly forecasting these fluctuations has proven difficult, but accurately determining the risk of extreme events can allow for the worst of the damage to be prevented. Here we trained Convolutional Neural Network models for eight mid-latitude magnetometers to predict the probability that dB/dt will exceed the 99th percentile threshold 30–60 min in the future. Two model frameworks were compared, a model trained using solar wind data from the Advanced Composition Explorer (ACE) satellite, and another model trained on both ACE and SuperMAG ground magnetometer data. The models were compared to examine if the addition of current ground magnetometer data significantly improved the forecasts of dB/dt in the future prediction window. A bootstrapping method was employed using a random split of the training and validation data to provide a measure of uncertainty in model predictions. The models were evaluated on the ground truth data during eight geomagnetic storms and a suite of evaluation metrics are presented. The models were also compared to a persistence model to ensure that the model using both datasets did not over-rely on dB/dt values in making its predictions. Overall, we find that the models using both the solar wind and ground magnetometer data had better metric scores than the solar wind only and persistence models, and was able to capture more spatially localized variations in the dB/dt threshold crossings.

Michael Coughlan↗
NASA NTRSDate not supplied

ANALYSIS OF THE MSL/MEDLI ENTRY DATA WITH COUPLED CFD AND MATERIAL RESPONSE.

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heat-shield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material. PICA is a lightweight carbon fiber/polymeric resin material that offers out-standing performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP). The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on Open-FOAM (PATO) using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA, is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Mars Science Laboratory↗
DOE OSTI2023

The Case for and Against a Gadolinium Bias in SCALE: Round 2

The “Opening Arguments” for and against a gadolinium bias in SCALE were presented at the American Nuclear Society Annual Meeting in Philadelphia, Pennsylvania, in June, 2018. Some critical experiments included in the Oak Ridge National Laboratory Verified, Archived Library of Inputs and Data (VALID) indicate a significant bias as a function of gadolinium concentration. Other experiments indicate that no significant bias exists. The work presented here develops a larger suite of gadolinium-bearing benchmark models to further examine code, data, and benchmark performance. The new benchmark models have been reviewed for accuracy, but documentation and review for addition to the VALID library have not been completed. The problematic benchmarks included in VALID are HEU-SOL-THERM-014 and -016. These are two evaluations from a series of experiments from the Institute for Physics and Power Engineering (IPPE), Russia, documented in the International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook. The entire set of evaluations also includes HEU-SOL-THERM-015, -017, -018, -019, and -025. Each evaluation contains a different uranium concentration, and different configurations within each evaluation include different gadolinium concentrations. These 7 evaluations contain a total of 52 configurations and form the largest subset of experiments considered, and they allow for a more complete assessment of the performance of these benchmarks than has historically been possible using just the HEU-SOL-THERM-014 and -016 results. Additional solution experiments are considered, including MIX-SOL-THERM-006 and -007 and PU-SOL-THERM-034. MIX-SOL-THERM-007 is in the VALID library, whereas MIX-SOL-THERM-006 and PU-SOL-THERM-034 are not. The results for MIX-SOL THERM-007 have not shown a gadolinium trend. These mixed- and plutonium-fueled solutions include 28 configurations. Some experiments including solid fuel and solid gadolinium are also included. These experiments include highly enriched uranium (HEU) foils moderated with polyethylene in HEU-MET-THERM-010, -016, and -034, and low enriched uranium (LEU) pin arrays with gadolinia absorber rods in LEU-COMP THERM-036 and -043. A total 32 cases with solid fuel are included. The IPPE solution benchmarks show a fairly high degree of variability, but no clear trend as a function of gadolinium concentration can be observed. The mixed- and plutonium-fueled solutions show less variability than the HEU solutions and also no trend relative to gadolinium concentration. The solid-fueled experiments also show no trend as a function of gadolinium content. The entire set of benchmarks shows no clear trend on gadolinium content or the energy of the average neutron lethargy causing fission.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Improving Runtime Performance of Tensor Computations using Rust From Python

In this work, we investigate improving the runtime performance of key computational kernels in the Python Tensor Toolbox (pyttb), a package for analyzing tensor data across a wide variety of applications. Recent runtime performance improvements have been demonstrated using Rust, a compiled language, from Python via extension modules leveraging the Python C API—e.g., web applications, data parsing, data validation, etc. Using this same approach, we study the runtime performance of key tensor kernels of increasing complexity, from simple kernels involving sums of products over data accessed through single and nested loops to more advanced tensor multiplication kernels that are key in low-rank tensor decomposition and tensor regression algorithms. In numerical experiments involving synthetically generated tensor data of various sizes and these tensor kernels, we demonstrate consistent improvements in runtime performance when using Rust from Python over 1) using Python alone, 2) using Python and the Numba just-in-time Python compiler (for loop-based kernels), and 3) using the NumPy Python package for scientific computing (for pyttb kernels).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

ARPA-E Grid Optimization (GO) Competition Challenge 3

Synthetic Input Data and Team Results for the GO Competition Challenge 3 for Events 1 - 4 and the Sandbox, along with problem and format descriptions and code to validate data and solutions, are available here. Data for industry scenarios will not be made public. The Grid Optimization (GO) Competition Challenge 3 focused on the security-constrained optimal power flow (SCOPF) problem. It is part of a continuing effort begun with Challenges 1 and 2, to successfully discover, develop, and test innovative and disruptive software solutions for critical energy challenges and to overcome existing barriers. The broader goal of the of the GO Competition is to accelerate the development of transformational and disruptive methods for solving problems related to the electric power grid and to provide a transparent, fair, and comprehensive evaluation of new solution methods. Challenge 3 used multiperiod dynamic markets, including advisory models for extreme weather events, day-ahead markets, and the real-time markets with an extended look-ahead. In Event 4, whose submission window was August 31-September 4, 2023, 14 teams solved for the objective values of 669 scenarios (39 scenarios required solutions both with and without line switching being allowed). The 591 synthetic scenarios from 9 network models (3.6 GB) are available here. Ten teams were funded to participate and 7 won prizes totaling $2,400,000. The largest prize ($550,000) went to Mississippi State University. An additional $600,000 was awarded in Event 3 (6/15-16/2023). No prizes were awarded in Events 1 (1/25-27/2023) or 2 (4/13-14/2023). For more information on the competition and challenge see the "GO Competition Challenge 3 Information" resource below.

ACOPF↗
NASA NTRS1989

The prediction of the noise generating mechanisms of an Aerospatiale 365N-1 Dauphin helicopter

The National Aeronautics and Space Administration (NASA) is engaged in a joint program with the U.S. helicopter industry to develop a full system helicopter noise prediction computer program called ROTONET. The long term goal of the system is to achieve the ability to predict a helicopter noise signature from the basic input of helicopter geometry and operating condition data. It is being developed in phases, with each phase representing an increase in sophistication. NASA is also performing a series of flight tests to provide a validation data base for the ROTONET System. A joint NASA/U.S. Army test of an Aerospatiale 365N-1 Dauphin helicopter is an element of the series. A comprehensive data base of spectra, noise level time histories, and effective perceived noise levels, incorporating actual meteorological conditions and helicopter dynamics, was produced from this test. Comparisons are made of predictions of the individual source generating mechanisms from the ROTONET System with data from the Aerospatiale 365N-1 Dauphin flyover test. EPNL and noise level time history comparisons demonstrate the overall capabilities of the prediction system. Graphs of 1/3 octave band noise spectra of experimental data and prediction allow identification of the dominant noise prediction mechanisms for various frequencies, directivity angles, and operating conditions.

Weir, Donald S.↗
NASA NTRS1999

TRMM-Based Merged Precipitation Analyses

This paper describes results of using Tropical Rainfall Measuring Mission (TRMM) information as the key calibration tool in a merged analysis on a 1X1 latitude/longitude monthly scale based on multiple satellite sources and raingauge analyses. The TRMM-based product is compared with surface-based validation data sets and the community-based 20-year Global Precipitation Climatology Project (GPCP)monthly analyses. The TRMM-based merged analysis uses the TRMM information to calibrate the estimates from SSM/I and geosynchronous IR observations and merges those estimates together with the TRMM and gauge information to produce accurate rainfall estimates with the increased sampling provided by the combined satellite information. This TRMM merged analysis uses the combined instrument (Precipitation Radar [PR] and TRMM Microwave Imager [TMI]) retrieval of Haddad as the TRMM estimate with which to calibrate the other satellite estimates. This TRMM Combined instrument (TCI) estimate is shown to produce very similar absolute values to the other main TRMM products. The TRMM and other satellites merged analysis compares favorably to the atoll data set of Morrissey for the months of 1998 with a very small positive bias of 2%. However, comparison with the preliminary results from the TRMM ground validation radar information at Kwajalein atoll in the western Pacific Ocean shows a 26% positive bias. Therefore, absolute magnitudes from TRMM and/or the ground validation need to be treated with care at this point. A month by month comparison of the TRMM merged analysis and the GPCP analysis indicates very similar patterns, but with subtle differences in magnitude. Focusing on the Pacific Ocean ITCZ one can see the TRMM-based estimates having higher peak values and lower values in the ITCZ periphery. These attributes also show up in the statistics, where GPCP>TRMM at low values (below 10 mm/d) and TRMM>GPCP at high values (greater than 15 mm/d). Integrated over the 37N-37S belt for all of 1998 the TRMM value is 3.1 mm/day compared to 2.9 mm/day for GPCP, with the results when confined to ocean being 3.3 and 3.0, respectively. Therefore, TRMM has approximately 10% higher tropical oceanic precipitation than GPCP. Examples of TRMM monthly fields in analysis of geographic and temporal variations will also be discussed. Results for 1998 indicate that TRMM has a different ratio of western Pacific to eastern Pacific rainfall than GPCP, perhaps indicating that TRMM's ability to discern the vertical structure of the rain may lead to better estimates in the eastern Pacific. In addition the rainfall anomalies associated with the '98-'99 ENSO event are shown to be larger with the TRMM results as compared to the GPCP analyses.

Adler, Robert↗
NASA NTRS2000

The Sandmeier Field Goniometer: A Measurement Tool for Bi-Directional Reflectance

Recent activities at the Remote Sensing Program at Stennis Space Center have identified the need to properly verify and validate data provided by the remote sensing community. One important variable, which effects remote sensing data is bi-directional reflectance distribution (BRDF). In order to quantify the effects of BRDF on man-made and natural ground targets, the Stennis Verification & Validation (V&V) team commissioned the Systems Engineering Division at NASA Ames Research Center to develop a Field Goniometer for use at the V&V Large Target Range and for various ground truthing missions. The Swiss Field Goniometer (FIGOS) was used as a benchmark instrument to design the new state of the art Sandmeier Field Goniometer (SGF), named after Stefan Sandmeier, developer of FIGOS. After establishing requirements for the SFG, design efforts began in early May 1998. The design of the SFG was completed in September 1998. Manufacturing, construction, and testing was completed in May 1999. The SFG was shipped to NASA SSC and fully operational by June 1999.

Turner, Mark↗
NASA NTRS2006

Development of a Numerical Model for High-Temperature Shape Memory Alloys

A thermomechanical hysteresis model for a high-temperature shape memory alloy (HTSMA) actuator material is presented. The model is capable of predicting strain output of a tensile-loaded HTSMA when excited by arbitrary temperature-stress inputs for the purpose of actuator and controls design. Common quasi-static generalized Preisach hysteresis models available in the literature require large sets of experimental data for model identification at a particular operating point, and substantially more data for multiple operating points. The novel algorithm introduced here proposes an alternate approach to Preisach methods that is better suited for research-stage alloys, such as recently-developed HTSMAs, for which a complete database is not yet available. A detailed description of the minor loop hysteresis model is presented in this paper, as well as a methodology for determination of model parameters. The model is then qualitatively evaluated with respect to well-established Preisach properties and against a set of low-temperature cycled loading data using a modified form of the one-dimensional Brinson constitutive equation. The computationally efficient algorithm demonstrates adherence to Preisach properties and excellent agreement to the validation data set.

DeCastro, Jonathan A.↗
DOE OSTI2025

Automation and machine learning drive rapid optimization of isoprenol production in Pseudomonas putida

Advances in genome engineering have improved our ability to perturb microbial metabolic networks, yet bioproduction campaigns often struggle with parsing complex metabolic datasets to efficiently enhance product titers. We address this challenge by coupling laboratory automation with machine learning to systematically optimize the production of isoprenol, a sustainable aviation fuel precursor, in Pseudomonas putida. The simultaneous downregulation through CRISPR interference of combinations of up to four gene targets, guided by machine learning, permitted us to increase isoprenol titer 5-fold in six consecutive design-build-test-learn cycles. Moreover, machine learning enabled us to swiftly explore a vast experimental design space of 800,000 possible combinations by strategically recommending approximately 400 priority constructs. High-throughput proteomics allowed us to validate CRISPRi downregulation and identify biological mechanisms driving production increases. Our work demonstrates that ML-driven automated design-build-test-learn cycles, when combined with rigorous data validation, can rapidly enhance titers without specific biological knowledge, suggesting that it can be applied to any host, product, or pathway.

Carruthers, David N↗
DOE OSTI2021

Loads Response That is Due to Wake Steering on a Pair of Utility-Scale Wind Turbines

The goal of this report is to present the resulting turbine loads of a full-scale wind turbine wake steering field campaign. In this experiment, wake steering controls were applied to an upwind turbine (T2) and the downwind turbine (T3) was instrumented to measure mechanical loads. The test subjects (T2 & T3) were GE 1.5SLE CWE turbines located on a wind farm with a prevailing wind direction coming from the northwest. The data collection strategy involved toggling the wake steering controls of T2 between on and off. This resulted in two databases (baseline and wake steered) with similar turbulence intensities. Valid data was extracted and processed. The analysis involved scaling data to engineering units, applying coordinate transformations where applicable, calculating 10-minutes statistics, and calculating damage equivalent loads (DELs) to assess fatigue. Figures are shown as statistics and DELs binned by wind speed with supplemental scatter plots provided in the appendices. Results between the baseline and wake steered databases were compared. Overall, the binned statistics showed minimal differences in loading between the two cases. However, the DELs of the wake steered case were observed to be consistently smaller than the baseline for most of the turbine components. A potential for future work was recognized based on the findings of this report. Some areas of further study include an analysis for more granular loads sensitivity to different yaw offset angles and rotor wake overlap, an in-depth comparison of loads between the upwind and downwind turbines, and further fatigue analysis to quantify differences observed in this experiment.

17 WIND ENERGY↗