Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “capacity factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Oversizing and Part-Load Problems

Oversizing, the common engineering practice of specifying devices with capacity exceeding the actual load requirement, is a widespread practice across virtually all building technologies end-use categories, including HVAC, electrical systems, lighting, appliances, and plug loads. This practice, driven by factors like design uncertainty, institutional pressures, and risk aversion, results in wasted capital investment, control difficulties, and excessive energy consumption due to inefficient part-load operation. Part-load operation, where devices run below maximum capacity, is the dominant operating mode in most energy systems and presents a complex design challenge. Solutions to match output to load fall into three broad categories: constraining the output, adjusting the device’s internal behavior, and linking output to energy storage or other waste-heat reuse applications. The energy implications of part-load are critical, as efficiency often drops sharply as load decreases across a wide diversity of devices. To quantify the extent of this problem, we derive a dimensionless Part-Load Metric (PLM) based on device efficiency and its frequency distribution of operating hours at various output levels. The PLM quantifies the deviation of a device's actual efficiency from its maximum design efficiency. This metric also serves as a measure of "capital inefficiency," enabling engineers to compare the impact of different part-load solutions and providing a unified framework for evaluating performance across various devices and systems.

Meier, Alan↗
DOE OSTI2020

Revisiting the Role of Conductivity and Polarity of Host Materials for Long-Life Lithium–Sulfur Battery

Despite their high theoretical energy density and low cost, lithium-sulfur batteries (LSBs) suffer from poor cycle life and low energy efficiency owing to the polysulfides shuttle and the electronic insulating nature of sulfur. Conductivity and polarity are two critical parameters for the search of optimal sulfur host materials. However, their role in immobilizing polysulfides and enhancing redox kinetics for long-life LSBs are not fully understood. In this work we have conducted an evaluation on the role of polarity over conductivity by using a polar but nonconductive platelet ordered mesoporous silica (pOMS) and its replica platelet ordered mesoporous carbon (pOMC), which is conductive but nonpolar. It is found that the polar pOMS/S cathode with a sulfur mass fraction of 80 wt% demonstrates outstanding long-term cycle stability for 2000 cycles even at a high current density of 2C. Furthermore, the pOMS/S cathode with a high sulfur loading of 6.5 mg cm -2 illustrates high areal and volumetric capacities with high capacity retention. Complementary physical and electrochemical probes clearly show that surface polarity and structure are more dominant factors for sulfur utilization efficiency and long-life, while the conductivity can be compensated by the conductive agent involved as a required electrode material during electrode preparation. The present findings shed new light on the design principles of sulfur hosts towards long-life and highly efficient LSBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Macroscopic Traffic Modeling Using Probe Vehicle Data: A Machine Learning Approach

Abstract The macroscopic fundamental diagram (MFD) captures an orderly relationship among traffic flow, density, and speed at the network level. It is a simple yet powerful tool for modeling traffic dynamics in large urban networks with broad application in traffic control and management. However, empirically derived MFDs in urban regions require high-resolution traffic data from the network. Having the network flow and vehicular density estimated at the (granular) census tract level using vehicle probe data, we apply machine learning methods to predict the MFDs across U.S. urban areas and capture the impacts of location-specific input features on the network flow–density relationships at a large scale. The results show that, among the four tested machine learning approaches (Random Forest, XGBoost, Support Vector Machine, and Neural Network), XGBoost delivers the best performance in predicting network traffic flow based on vehicular density and location attributes. Using interaction Shapley Additive explanation (SHAP) values and partial correlation analysis, we examine the factors influencing MFD shapes across different locations. Our empirical findings reveal that across U.S. urban areas, network topology, transportation infrastructure, and land use are primary factors shaping MFD curves, while demand and trip-related factors play a lesser role. Specifically, higher ranking roads, centrality, and development levels correlate positively with network capacity and critical density, whereas negative associations are observed for network connectivity, mixed-use development, and road roughness levels.

Jin, Ling↗
DOE OSTI2021

IGF-1 Receptor Signaling Regulates Type II Pneumocyte Senescence and Resulting Macrophage Polarization in Lung Fibrosis

Type II pneumocyte (alveolar epithelial cells type II [AECII]) senescence has been implicated in the progression of lung fibrosis. The capacity of senescent cells to modulate pulmonary macrophages to drive fibrosis is unexplored. Insulin-like growth factor-1 receptor (IGF-1R) signaling has been implicated as a regulator of senescence and aging.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2021

Simplifying computational workflows with the Multiscale Atomic Zeolite Simulation Environment (MAZE)

Zeolites, an important class of 3-dimensional nanoporous materials, have been widely explored for a variety of applications including gas storage, separations, and catalysis. As the properties of these aluminosilicate materials depend on a number of factors (e.g., framework topology, Si/Al ratio, extra-framework cations etc.), detailed experiments (e.g., catalytic properties, adsorption capacities etc.) are often limited to only a handful of materials. Computational methods have played an important role in (1) providing molecular level insights to rationalize experimental observations, and (2) screening large libraries of zeolites to identify promising candidates for experimental synthesis and validation. Different levels of theory and computational chemistry codes are necessary to describe the range of relevant phenomena such as adsorption (e.g., grand canonical Monte Carlo), diffusion (e.g., molecular dynamics), and chemical reactions (e.g., density functional theory). Manipulation of atomic structures, handling of input files, and developing robust workflows becomes quite cumbersome. To mitigate these challenges, we describe the development of the Multiscale Atomic Zeolite Simulation Environment (MAZE) – a Python package that simplifies zeolite-specific calculation workflows by providing a user-friendly interface for systematically manipulating zeolite structures

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Cryptococcus neoformans Secretes Small Molecules That Inhibit IL-1 β Inflammasome-Dependent Secretion

Cryptococcus neoformans is an encapsulated yeast that causes disease mainly in immunosuppressed hosts. It is considered a facultative intracellular pathogen because of its capacity to survive and replicate inside phagocytes, especially macrophages. This ability is heavily dependent on various virulence factors, particularly the glucuronoxylomannan (GXM) component of the polysaccharide capsule. Inflammasome activation in phagocytes is usually protective against fungal infections, including cryptococcosis. Nevertheless, recognition of C. neoformans by inflammasome receptors requires specific changes in morphology or the opsonization of the yeast, impairing proper inflammasome function. In this context, we analyzed the impact of molecules secreted by C. neoformans B3501 strain and its acapsular mutant Δcap67 in inflammasome activation in an in vitro model. Our results showed that conditioned media derived from B3501 was capable of inhibiting inflammasome-dependent events (i.e., IL-1β secretion and LDH release via pyroptosis) more strongly than conditioned media from Δcap67, regardless of GXM presence. We also demonstrated that macrophages treated with conditioned media were less responsive against infection with the virulent strain H99, exhibiting lower rates of phagocytosis, increased fungal burdens, and enhanced vomocytosis. Moreover, we showed that the aromatic metabolite DL-Indole-3-lactic acid (ILA) and DL-p-Hydroxyphenyllactic acid (HPLA) were present in B3501’s conditioned media and that ILA alone or with HPLA is involved in the regulation of inflammasome activation by C. neoformans. These results were confirmed by in vivo experiments, where exposure to conditioned media led to higher fungal burdens in Acanthamoeba castellanii culture as well as in higher fungal loads in the lungs of infected mice. Overall, the results presented show that conditioned media from a wild-type strain can inhibit a vital recognition pathway and subsequent fungicidal functions of macrophages, contributing to fungal survival in vitro and in vivo and suggesting that secretion of aromatic metabolites, such as ILA, during cryptococcal infections fundamentally impacts pathogenesis.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

High Resolution Siting Suitability of Various Power Plant Technologies

Energy sector planning models determine the aggregate need for new generation, but these models are typically at the state or regional scale and are not equipped to address the wide range of location- and technology-specific issues that are increasingly a factor in power plant siting. These animations demonstrate the aggregate siting suitability of various power plant technology configurations, considering technology-specific factors that can prohibit development. The data presented is from the GRIDCERF (Geospatial Raster Input Data for Capacity Expansion Regional Feasibility) data package. GRIDCERF is a harmonized, open-source geospatial product that can be used to evaluate siting suitability for renewable and non-renewable power plants in the conterminous United States. The animations presented here demonstrate a curated selection of the full suite of technology configurations available. GRIDCERF provides the necessary inputs for models that simulate power plant siting for regional capacity expansion planning such as the Capacity Expansion Regional Feasibility (CERF) model.

Mongird, Kendall [Pacific Northwest National Labor↗
DOE OSTI2026

Trends and limits of CO 2 capture in solid and liquid sorbents at standard conditions

Carbon capture and storage (CCS) plays a critical role in achieving climate change mitigation targets, offering a pathway to decarbonize power generation, industrial processes, and heat production while addressing atmospheric CO 2 removal. While CCS technologies are technically advanced, the widespread adoption of 100 % CO 2 capture capacities such as 1 mol of CO 2 /mol of material and 1 g CO 2 /g storage (targeted by the DARPA, Defense Sciences Office, USA Govt.) has raised questions about the feasibility of achieving higher capture capacities. In the context of limiting global warming to 1.5°C, reaching 100 % CO 2 capture capacity is increasingly necessary, with residual emissions requiring complementary carbon dioxide removal (CDR) technologies. This review exclusively focuses on the CO 2 capture capacities of various sorbents under standard conditions, using different evaluation metrics. This study explores the performance of solid and liquid sorbents under standard conditions, analyzing factors including surface area, pore structure, solvent type, and functionalization to identify materials optimized for industrial-scale CCS applications. Emerging sorbents, including ILs, MOFs, COFs, POPs, DES, RCC, hybrid materials, and reactive sorbents, offer significant potential for enhanced selectivity and energy-efficient regeneration. Through a systematic assessment of gravimetric, volumetric, and molar capacities, the study provides insights into material efficiencies and trade-offs, offering guidance on optimizing sorbent selection for specific applications. The research advances understanding of scalable CCS technologies, contributing to global efforts to achieve net-zero emissions and address the pressing challenge of climate change.

Absorption↗
DOE OSTI2020

Drug Resistance in Filarial Parasites Does Not Affect Mosquito Vectorial Capacity

Parasite drug resistance presents a major obstacle to controlling and eliminating vector-borne diseases affecting humans and animals. While vector-borne disease dynamics are affected by factors related to parasite, vertebrate host and vector, research on drug resistance in filarial parasites has primarily focused on the parasite and vertebrate host, rather than the mosquito. However, we expect that the physiological costs associated with drug resistance would reduce the fitness of drug-resistant vs. drug-susceptible parasites in the mosquito wherein parasites are not exposed to drugs. Here we test this hypothesis using four isolates of the dog heartworm (Dirofilaria immitis)—two drug susceptible and two drug resistant—and two vectors—the yellow fever mosquito (Aedes aegypti) and the Asian tiger mosquito (Ae. albopictus)—as our model system. Our data indicated that while vector species had a significant effect on vectorial capacity, there was no significant difference in the vectorial capacity of mosquitoes infected with drug-resistant vs. drug-susceptible parasites. Consequently, contrary to expectations, our data indicate that drug resistance in D. immitis does not appear to reduce the transmission efficiency of these parasites, and thus the spread of drug-resistant parasites in the vertebrate population is unlikely to be mitigated by reduced fitness in the mosquito vector.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Limits to forests-based mitigation in integrated assessment modelling: global potentials and impacts under constraining factors

Forests-based measures such as afforestation/reforestation (A/R) and reducing deforestation (RDF) are considered promising options to mitigate climate change, yet their mitigation potentials are limited by economic and biophysical factors that are largely uncertain. The range of mitigation potential estimates from integrated assessment models raises concerns about the capacity of land systems to provide realistic, cost-effective and permanent land-based mitigation. We use the Global Change Analysis Model to quantify the economic mitigation potential of forests-based measures by simulating a climate policy including a tax on greenhouse gas emissions from agriculture, forestry, and other land uses. In addition, we assess how constraining unused arable land (UAL) availability, forestland expansion rates, and global bioenergy demand may influence the forests-based mitigation potential by simulating scenarios with alternative combinations of constraints. Results show that the average forests-based mitigation potential in 2020–2050 increases from 738 MtCO 2 .yr -1 through a forestland increase of 86 Mha in the fully constrained scenario to 1394 MtCO 2 .yr -1 through a forestland increase of 146 Mha when all constraints are relaxed. Regional potentials in terms of A/R and RDF differ strongly between scenarios: unconstrained forest expansion rates mostly increase A/R potentials in northern regions (e.g., +120 MtCO 2 .yr -1 in North America); while unconstrained UAL conversion and low bioenergy demand mostly increase RDF potentials in tropical regions (e.g., +76 and +68 MtCO 2 .yr -1 in Southeast Asia, respectively). This study shows that forests-based mitigation is limited by many factors that constrain the rates of land use change across regions. These factors, often overlooked in modelling exercises, should be carefully addressed for understanding the role of forests in global climate mitigation and defining pledges towards the Paris Agreement.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Ionomer Optimization for Water Uptake and Swelling in Anion Exchange Membrane Electrolyzer: Hydrogen Evolution Electrode

Green hydrogen produced through anion exchange membrane water electrolysis is a promising, low-cost chemical storage solution for intermittent renewable energy sources. Low-temperature electrolysis using anion exchange membranes (AEM) combines the benefits of established water electrolysis technologies based on alkaline electrolysis and proton exchange membrane electrolysis. The anion conductive ionomers (ACI) used in the AEM electrolyzer (AEMEL) electrodes has been investigated. The ACI serves two primary purposes: (i) facilitate hydroxide conduction between the catalyst and bulk electrolyte and (ii) bind the catalyst to the porous transport layer and membrane. High ion exchange capacity (IEC) ACIs are desired, however, high IEC can cause excessive water uptake (WU) and detrimental ACI swelling. Proper water management is a key factor in obtaining maximum performance in AEM-based devices. In this study, a series of poly(norbornene)-based ACIs were synthesized and deployed in hydrogen evolving AEMEL cathode electrodes. A balance between ionic conductivity, WU and ionomer swelling was achieved in the ACI by varying the IEC and degree of polymer cross-linking. It was found that higher IEC ACIs with light crosslinking are preferred in the HER electrode. Furthermore, such a configuration fine-tuned the WU and ionomer swelling to achieve optimum cell performance and reduce cell operating voltages.

08 HYDROGEN↗
DOE OSTI2024

GCAM–GLORY v1.0: representing global reservoir water storage in a multi-sector human–Earth system model

Abstract. Reservoirs play a significant role in modifying the spatiotemporal availability of surface water to meet multi-sector human demands, despite representing a relatively small fraction of the global water budget. Yet the integrated modeling frameworks that explore the interactions among climate, land, energy, water, and socioeconomic systems at a global scale often contain limited representations of water storage dynamics that incorporate feedbacks from other systems. In this study, we implement a representation of water storage in the Global Change Analysis Model (GCAM) to enable the exploration of the future role (e.g., expansion) of reservoir water storage globally in meeting demands for, and evolving in response to interactions with, the climate, land, and energy systems. GCAM represents 235 global water basins, operates at 5-year time steps, and uses supply curves to capture economic competition among renewable water (now including reservoirs), non-renewable groundwater, and desalination. Our approach consists of developing the GLObal Reservoir Yield (GLORY) model, which uses a linear programming (LP)-based optimization algorithm and dynamically linking GLORY with GCAM. The new coupled GCAM–GLORY approach improves the representation of reservoir water storage in GCAM in several ways. First, the GLORY model identifies the cost of supplying increasing levels of water supply from reservoir storage by considering regional physical and economic factors, such as evolving monthly reservoir inflows and demands, and the leveled cost of constructing additional reservoir storage capacity. Second, by passing those costs to GCAM, GLORY enables the exploration of future regional reservoir expansion pathways and their response to climate and socioeconomic drivers. To guide the model toward reasonable reservoir expansion pathways, GLORY applies a diverse array of feasibility constraints related to protected land, population, water sources, and cropland. Finally, the GLORY–GCAM feedback loop allows evolving water demands from GCAM to inform GLORY, resulting in an updated supply curve at each time step, thus enabling GCAM to establish a more meaningful economic value of water. This study improves our understanding of the sensitivity of reservoir water supply to multiple physical and economic dimensions, such as sub-annual variations in climate conditions and human water demands, especially for basins experiencing socioeconomic droughts.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Public Reference Data for Megawatt-Scale Hydrogen Electrolysis - NLR Historical Solar PV

The U.S. Department of Energy and National Laboratory of the Rockies (NLR) demonstrate hydrogen electrolysis from variable sources, hydrogen compression and storage, and hydrogen fuel cell power production using megawatt-scale equipment at NLR’s Flatirons Campus as part of the Advanced Research on Integrated Energy Systems (ARIES) research platform. This dataset represents part of that effort and is intended for academic, national laboratory, industrial, and other stakeholders to plan, design, and validate models of megawatt-scale hydrogen technologies and diverse energy infrastructure nationwide. These data provide a baseline for how existing hydrogen electrolysis technologies perform when coupled with various energy technologies. Future datasets will demonstrate how existing hydrogen fuel cell technologies can provide controllable, dispatchable, and variable power output for artificial intelligence data centers and other variable loads. This dataset entry describes the behavior of a 1.25-MW proton exchange membrane MC250 electrolyzer system, manufactured by Nel Hydrogen , [1] when fed historical data generated by the 430-kW, fixed-axis solar photovoltaic (PV) array located at NLR’s Flatirons Campus. (While the electrolyzer balance of plant supports up to 2.5 MW of electrolysis, NLR only has a single 1.25-MW electrolysis stack.) Solar PV power output data for the 2020 calendar year were categorized on a daily basis by total energy generation and standard deviation. Each day was then ranked by these metrics, and the 25th, 50th, and 100th percentiles were selected. The 75th percentile day did not exhibit sufficient variability to make for a valuable experiment. A similar process was used for the related historical wind dataset . [2] The historical days in 2020 that represented these percentiles are Dec. 19, March 29, and May 4, respectively. The entire solar day’s power profile was then fed through the MC250 electrolyzer. Due to its length, the 100th percentile day experiment was split into two parts, and the final 3 hours of the solar day were not captured. These final 3 hours contained no spikes or dips of interest and simply represented a slow decay of input solar power. Also, a single timestamp (13:13:47 on Jan. 14, 2026) was lost in the hydrogen system supervisory control and data acquisition. Finally, during the 25th percentile experiment (solar day Dec. 19, 2020) data recording was lost from 11:00:13 to 11:14:45. The roughly 15 minutes of the solar profile were rerun at the end of the experiment and spliced into this time slot during post-processing. The electrolysis system controls hydrogen production by varying direct current applied to the stack, from a maximum of 3,000 A to a minimum safe operation of 300 A, or 10%. Because the current–voltage characteristic changes as the stack ages and efficiency degrades, the actual minimum safe operating power changes over time. The historical solar profiles were translated from power (kilowatts) to current (amperes) using a curve fit with calibration data and sent to the electrolyzer power supply at 1-Hz frequency. For more details on the statistical analysis process, see the slide deck “Public Reference Data for Megawatt-Scale Hydrogen Electrolysis: NLR Historical Solar PV Analysis and Profile Generation” accessible with this data entry. These datasets report relevant hydrogen balance-of-plant and system data, all captured at 1 Hz, including hydrogen mass production measured with an Emerson Coriolis flow meter. Each .zip file represents a single solar PV electrolysis experiment and is formatted as: {technology}_{percentile}_{scaling factor} For instance, “solarPV-430kW_25_2x.zip” reports the experiment using the 25th percentile solar data from the historical 2020 solar PV dataset, scaled to 200%. Scaling factors were applied to the generated solar PV power output files to more closely match the 1.25-MW capacity of the electrolyzer. Each .zip folder contains the following files: A .csv file containing raw data. An .xlsx file explaining all the fields in the raw data. A .png plot showing the time series of hydrogen production, electrolysis power consumption, and solar power input. A PDF file detailing the historical solar data statistical analysis used to generate the solar profile. An experiment labeled “characterization_200.zip” demonstrates the MC250 electrolyzer steady-state response with 30-minute load steps for a total duration of 5 hours. Finally, a .csv file is provided with all experiments combined into one dataset labeled "combined_solarPV_experiments.csv". [1] nelhydrogen.com/product/mc-series-electrolyser . [2] data.nlr.gov/submissions/316 .

08 HYDROGEN↗
DOE OSTI2025

A Novel Secondary Frequency Regulation with Optimal Priority Selection of AGC Contributions

Automatic generation control (AGC) is used to maintain acceptable frequencies during operation owing to fluctuations in load and variable resources. In conventional industry applications, the AGC signal is allocated to each generator according to the predispatched frequency regulation capacity or the order of economic efficiency. However, with the increasing integration of inverter-based resources (IBRs), the retirement of conventional synchronous generators (SGs) has posed new challenges to frequency control schemes because fewer of them are optional for AGC regulation. In this paper, we propose a novel model predictive control (MPC)-based frequency regulation model to reduce control cost and ensure stability, by considering different critical dynamic factors when optimally selecting the AGC units. The proposed control model – developed in a general form – comprehensively embeds characteristics such as generator ramping rates, reserve capacity, and operation cost. The model predictive control–based two-timescale AGC scheme enhances the capability of immunizing the power disturbance from types of resources by coordinating the control signals between faster IBRs and slower SGs. The case study’s proposed model is verified to be effective in synergistically enforcing different dynamic properties of AGC units into the frequency regulation scheme.

Jiang, Sufan [The University of North Carolina at ↗
DOE OSTI2021

Suppression of antiferromagnetic order and strong ferromagnetic spin fluctuations in Ca(Co 1-x Ni x ) 2-y As 2 single crystals

CaCo 2–y As 2 is a unique itinerant system having strong magnetic frustration. Here, we report the effect of electron doping on the physical properties resulting from Ni substitutions for Co. The single crystals of Ca(Co 1–x Ni x ) 2–y As 2 were characterized by single-crystal x-ray diffraction, energy-dispersive x-ray spectroscopy, magnetization M versus temperature T, magnetic field H, time t, and heat capacity C p (H, T) measurements. The A-type antiferromagnetic (AFM) transition temperature T N = 52 K for x = 0 decreases to 22 K with only 3% Ni substitution and is completely suppressed for x > 0.16. For 0.11 ≤ x ≤ 0.52 strong ferromagnetic (FM) fluctuations develop as revealed by magnetic susceptibility χ(T) = M(T) / H measurements. For x = 0.11 and 0.16 competing AFM and FM interactions result in a reentrant spin-glass behavior below T N , as evidenced by the observations of thermomagnetic hysteresis and magnetic relaxation. Enhanced FM fluctuations are also found for the x = 0.21 and 0.31 crystals, where χ c increases significantly at low T. A large χ anisotropy in these compositions where χ c is up to a factor of two larger than χ ab suggests that the FM spin fluctuations are quasi-1D in nature. Weak ferromagnetic contributions to the magnetization are found at T = 2 K for x = 0.11 –0.31. Heat-capacity Cp(T) measurements reveal the presence of FM quantum spin fluctuations for 0.11 ≤ x ≤ 0.52, where a logarithmic T dependence of Cp(T) / T is observed at low T. Here, the suppression of AFM order by the development of strong FM fluctuations in Ca(Co 1–x Ni x ) 2–y As 2 crystals suggests the presence of a FM quantum-critical point at x ≈ 0.20. Our density-functional theory (DFT) calculations confirm that FM fluctuations are enhanced by Ni substitutions for Co in CaCo 2–y As 2 . The Sommerfeld electronic heat-capacity coefficient is enhanced for x = 0, 0.21, and 0.42 by about a factor of two compared to DFT calculations of the density of states (DOS) at the Fermi energy, suggesting an enhancement of the DOS from electron-phonon and/or electron-electron interactions. The crystals with x > 0.52 do not exhibit FM spin fluctuations or magnetic order at T ≥ 1.8 K, which was found from the DFT calculations to arise from a Stoner transition. Superconductivity is not observed above 1.8 K for any of the compositions. Neutron-diffraction studies of crystals with x = 0.11 and 0.16 in the crossover regime (0.1 ≲ x ≲ 0.2) show no evidence of A-type ordering as observed in the parent compound with x = 0. Furthermore, no other common magnetic structures, such as ferromagnetic (FM), helical stacking of in-plane FM layers, or in-plane AFM structure, are found with an ordered moment greater than the uncertainty of 0.05 μ B per transition-metal atom.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Magnetostriction and damping of forced vibrations in Fe-Mo single and polycrystal alloys

Magnetostriction and damping of forced vibrations in Fe-Mo single and polycrystal alloys is studied and analyzed with respect to existing approaches and experimental data. In this work, our data suggest that a more complex dependence (compared with linear dependence predicted by Smith and Birchak) between damping capacity and magnetostriction takes place for this and possibly other Fe-based ferromagnetic alloys. We believe that more factors related to the structural changes, brought about by the additions (elements added to Fe), which can affect phase stability as well as magnetic and electric contributions influencing property response, should be considered to provide a better correlation between the magnetic and magnetomechanical characteristics of this alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Global Electrification of Vehicles and Intertwined Material Supply Chains of Cobalt, Copper and Nickel

Electric vehicles (EVs) will be an important part of a low-carbon economy. Future EV adoption depends on overcoming multiple barriers, including charging infrastructure, sufficient electricity generation, and the availability of battery raw materials at acceptable costs, including cobalt, copper and nickel – which typically are co-produced. Various EV projections have been made, along with associated requirements for battery raw materials (demand). There have been separate assessments of the availability of raw materials (supply). However, integrated assessments of supply and demand and their interaction over time are lacking to support decision-making. Using a dynamic market model that reflects the co-produced nature of cobalt, copper and nickel production as well as recycling, we estimate global output of these three metals under different EV growth scenarios from 2020 to 2040. In this work, results suggest that starting in 2025, replacement demand for battery raw materials becomes important. Thus, estimates for future material demand that consider only demands from new EVs are incomplete and misleading. EV deployment and associated increased demand for raw materials will have a greater impact on prices for cobalt than nickel and, in turn, for nickel than copper. High EV deployment scenarios will be difficult to achieve without larger supplies of copper, nickel and cobalt than forthcoming under the conditions modeled here, which anticipates a six-year time lag between a demand increase and the expansion of metal-production capacity. Shortening battery lifetimes and improving collection and recycling rates increase secondary supply, but the extent to which these factors support additional EV deployment is mixed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Aging-associated stem/progenitor cell dysfunction in the salivary glands of mice

Highlights: • The function of CD133-positive cells changes with age and is expected to be one of the causative factors associated with salivary gland aging. Although stem cell aging leads to a decline in tissue homeostasis and regenerative capacity, it remains unclear whether salivary gland stem cell function changes during this process. However, the salivary glands are gradually replaced by connective tissue during aging. Here, we show a decline in the stem cell ability of CD133-positive stem/progenitor cells in the salivary glands of aged mice. The CD133-positive cells were isolated from young, adult, and aged mice. The number of CD133-positive cells was significantly decreased in aged mice. They also showed a lower sphere formation capacity compared to young and adult mice. RNA sequencing revealed that CD133-positive cells in aged mice exhibited lower gene expression of several aging-related genes, including FoxO3a, than those in young and adult mice. Salivary gland cells infected with a recombinant lentivirus encoding the FoxO3a gene showed a reduction in oxidative stress induced by hydrogen peroxide compared with those infected with a control virus. Thus, FoxO3a may inhibit stem cell aging via oxidative stress.

60 APPLIED LIFE SCIENCES↗