Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “YOUNG MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Investigation of Stress Field and Fracture Development During Shale Maturation Using Analog Rock Systems

The emergence of hydrocarbons within shale as a major recoverable resource has sparked interest in fluid transport through these tight mudstones. Recent studies suggest the importance to recovery of microfracture networks that connect localized zones with large organic content to the inorganic matrix. This paper presents a joint modeling and experimental study to examine the onset, formation, and evolution of microfracture networks as shale matures. Both the stress field and fractures are simulated and imaged. A novel laboratory-scale, phase-field fracture propagation model was developed to characterize the material failure mechanisms that play a significant role during the shale maturation process. The numerical model developed consists of coupled solid deformation, pore pressure, and fracture propagation mechanisms. Benchmark tests were conducted to validate model accuracy. Laboratory-grade gelatins with varying Young’s modulus were used as scaled-rock analogs in two dimensional Hele-Shaw cell apparatus. Yeast within the gelatin generates gas in a fashion analogous to hydrocarbon formation as shale matures. These setups allow study and visualization of host rock elastic-brittle fracture and fracture network propagation mechanisms. The experimental setup was fitted to utilize photoelasticity principles coupled with birefringence properties of gelatin to explore visually the stress field of the gelatin as the fracture network developed. Stress optics image analysis and Linear Elastic Fracture Mechanics (LEFM) principles for crack propagation were used to monitor fracture growth for each gelatin type. Observed and simulated responses suggest gas diffusion within and deformation of the gelatin matrix as predominant mechanisms for energy dissipation depending on gelatin strength. LEFM, an experimental estimation of principal stress development with fracture growth, at different stages was determined for each gelatin rheology. Here, the interplay of gas diffusion and material deformation determines the resulting frequency and pattern of fractures. Results correlate with Young’s modulus. Experimental and computed stress fields reveal that fractures resulting from internal gas generation are similar to, but not identical to, type 1 opening mode.

58 GEOSCIENCES↗

Microhardness, chemical etching, SEM, AFM and SHG studies of novel nonlinear optical crystal -L-threonine formate

Highlights: Black-Right-Pointing-Pointer Microhardness studies of novel LTF crystal reported first time in the literature. Black-Right-Pointing-Pointer Surface studies are done by AFM, chemical etching and SEM. Black-Right-Pointing-Pointer From SHG studies, it is known that LTF is potential NLO crystal. -- Abstract: The crystal L-threonine formate, an organic NLO crystal was synthesized from aqueous solution by slow evaporation technique. The grown crystal surface has been analyzed by scanning electron microscopy (SEM), chemical etching and atomic force microscopy (AFM). SEM analysis reveals pyramidal shaped minute crystallites on the growth surface. The etching study indicates the occurrence of etch pit patterns like striations and step like pattern. The mechanical properties of LTF crystals were evaluated by mechanical testing which reveals certain mechanical characteristics like elastic stiffness constant (C{sub 11}) and young's modulus (E). The Vickers and Knoop microhardness studies have been carried out on LTF crystals over a range of 10-50 g. Hardness anisotropy has been observed in accordance with the orientation of the crystal. AFM image shows major hillock on growth surface. The second harmonic generation (SHG) efficiency has been tested by the Kurtz powder technique using Nd:YAG laser and found to be about 1.21 times in comparison with standard potassium dihydrogen phosphate (KDP) crystals.

36 MATERIALS SCIENCE↗

The Prediction and Simulation for the Mechanical Properties of Ceramic-Based Composites Reinforced with Nano-Micro Particles

The global-local homogenization method with precise period boundary conditions is applied to predict and simulate the mechanical properties of ceramic composites reinforced by spherical nano-micro particles with enwrapping and nesting arrays. The numerical simulation is performed with different size ratios of nano-micro particles, and different configurations for representative volume element. The results show that the low radius ratios of nano-micro particles produce a larger effective Young's modulus for its more uniform dispersion, and the hexagon RVE with nesting array can make an overestimation for effective elastic modulus of ceramic composites, and the interfacial damage between nano-microscopic particles and matrix degenerates the effective elastic modulus. It shows in this paper that it is significant to improve the mechanical properties of ceramic materials by mixing some nano- and micro-particles into the matrix with good designed array methods from the viewpoints of nano-microscopic crystal structure, and a rational interfacial damage model should be further proposed to investigate the toughening mechanism of ceramic-composites reinforced with nano-micro particles.

36 MATERIALS SCIENCE↗

Pressure-assisted fabrication of organic light emitting diodes with MoO{sub 3} hole-injection layer materials

In this study, pressures of ∼5 to ∼8 MPa were applied to organic light emitting diodes containing either evaporated molybdenum trioxide (MoO{sub 3}) or spin-coated poly(3,4-ethylene dioxythiophene) doped with poly(styrene sulphonate) (PEDOT:PSS) hole-injection layers (HILs). The threshold voltages for both devices were reduced by about half, after the application of pressure. Furthermore, in an effort to understand the effects of pressure treatment, finite element simulations were used to study the evolution of surface contact between the HIL and emissive layer (EML) under pressure. The blister area due to interfacial impurities was also calculated. This was shown to reduce by about half, when the applied pressures were between ∼5 and 8 MPa. The finite element simulations used Young's modulus measurements of MoO{sub 3} that were measured using the nanoindentation technique. They also incorporated measurements of the adhesion energy between the HIL and EML (measured by force microscopy during atomic force microscopy). Within a fracture mechanics framework, the implications of the results are then discussed for the pressure-assisted fabrication of robust organic electronic devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermal and mechanical properties of LaCoO3 and La0.8Ca0.2CoO3 perovskites

In this work, the thermal and mechanical properties, such as coefficient of thermal expansion, strength, Young s modulus and fracture toughness of LaCoO3 and La0.8Ca0.2CoO3 perovskites have been studied, as well as slow crack growth of La0.8Ca0.2CoO3. The mechanical performance of the two cobaltites have been evaluated in terms of their ferroelastic hysteresis properties such as non-symmetry in bending of both stress and strain distributions, non-linear deformation upon applied load from the arbitrary low stresses, and ferroelastic toughening.

36 MATERIALS SCIENCE↗

Physicochemical, Antimicrobial and Cytotoxic Characteristics of Corn Starch Film Containing Propolis for Wound Dressing

Modern dressings increase the rate of wound healing rather than just covering them. Dressing can protect the injured skin and keep it appropriately moist to speed up the healing process. In this study, the ethanolic extract of propolis loaded with corn starch was successfully prepared using solvent casting. Characterizations of the samples performed in respect to their mechanical properties were examined by scanning electron microscopy, contact angle, and attenuated total reflectance—fourier transform infrared spectroscopy, as well as antimicrobial capacities. The MTT assay using fibroblast cells showed the cell viability of corn starch in the ethanolic extract of propolis wound dressing. The results showed that by increasing the amount of ethanolic propolis extract from 0.25 to 1%, the tensile strength and the Young’s modulus of the samples were decreased, the elongation at the break increased about 15% as compared to the control films, and the contact angle properties were detected by a slightly hydrophobic character of the films in the antibacterial activity against Escherichia coli and Staphylococcus aureus even at low ethanolic extract of propolis concentrations (1%), mainly due to its phenolic compounds. Therefore, ethanolic extract of propolis loaded with corn starch film will be a potential candidate for wound dressing and skin tissue engineering.

36 MATERIALS SCIENCE↗

Uncertainty quantification for evaluating impacts of caprock and reservoir properties on pressure buildup and ground surface displacement during geological CO2 sequestration

A series of numerical test cases reflecting broad and realistic ranges of geological formation properties was developed to systematically evaluate and compare the impacts of those properties on geomechanical responses to CO2 injection. A coupled hydro-geomechanical subsurface transport simulator, STOMP (Subsurface Transport over Multiple Phases), was adopted to simulate the CO2 migration process and geomechanical behaviors of the surrounding geological formations. A quasi-Monte Carlo sampling method was applied to efficiently sample a high-dimensional parameter space consisting of injection rate and 14 subsurface formation properties, including porosity, permeability, entry pressure, irreducible gas and aqueous saturation, Young’s modulus, and Poisson’s ratio for both reservoir and caprock. Generalized cross-validation and analysis of variance methods were used to quantitatively measure the significance of the 15 input parameters. Reservoir porosity, permeability, and injection rate were found to be among the most significant factors affecting the geomechanical responses to the CO2 injection. We used a quadrature generalized linear model to build a reduced-order model that can estimate the geomechanical response instantly instead of running computationally expensive numerical simulations.

CO2 geological sequestration↗

Flux Pinning-Induced Stress in a Long Hollow Cylindrical Superconductor Restricted by a Metal Tube

The tensile stress in a hollow cylindrical superconductor completely restricted by a metal tube in a parallel magnetic field is investigated. Using the plane strain approach, analytical expressions for the stress distribution of the superconductor and the contact stress between the metal tube and the superconductor are obtained and show that both the ratio of Young’s modulus and thickness ratio of the high-temperature superconductors and the metal tube significantly affect the stress distribution in the superconductor explicitly. In addition, the flux pinning-induced stress in the above-mentioned superconductor is systematically studied by the exponential critical state model during the field cooling process. The results indicate that the metal tube can reduce effectively the tensile stress in the hollow cylindrical superconductor during the magnetization process. The findings suggest that the appropriate selection of material parameters and size of the metal tube can improve superconductor performance efficiently.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mechanical deformations of boron nitride nanotubes in crossed junctions

We present a study of the mechanical deformations of boron nitride nanotubes (BNNTs) in crossed junctions. The structure and deformation of the crossed tubes in the junction are characterized by using atomic force microscopy. Our results show that the total tube heights are reduced by 20%–33% at the crossed junctions formed by double-walled BNNTs with outer diameters in the range of 2.21–4.67 nm. The measured tube height reduction is found to be in a nearly linear relationship with the summation of the outer diameters of the two tubes forming the junction. The contact force between the two tubes in the junction is estimated based on contact mechanics theories and found to be within the range of 4.2–7.6 nN. The Young's modulus of BNNTs and their binding strengths with the substrate are quantified, based on the deformation profile of the upper tube in the junction, and are found to be 1.07 ± 0.11 TPa and 0.18–0.29 nJ/m, respectively. Finally, we perform finite element simulations on the mechanical deformations of the crossed BNNT junctions. The numerical simulation results are consistent with both the experimental measurements and the analytical analysis. The results reported in this paper contribute to a better understanding of the structural and mechanical properties of BNNTs and to the pursuit of their applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Note: A component-level frequency tunable isolator for vibration-sensitive chips using SMA beams

This note presents a component-level frequency tunable isolator for vibration-sensitive chips. The isolator employed 8 U-shaped shape memory alloy (SMA) beams to support an isolation island (used for mounting chips). Due to the temperature-induced Young’s modulus variation of SMA, the system stiffness of the isolator can be controlled through heating the SMA beams. In such a way, the natural frequency of the isolator can be tuned. A prototype was fabricated to evaluate the concept. The test results show that the natural frequency of the isolator can be tuned in the range of 64 Hz–97 Hz by applying different heating strategies. Moreover, resonant vibration can be suppressed significantly (the transmissibility decreases about 65% near the resonant frequency) using a real-time tuning method.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of bulk highly faulted fcc/hcp nanostructured cobalt microstructures

Nanostructured cobalt powders with an average particle size of 50 nm were synthesized using a polyol method and subsequently consolidated by spark plasma sintering (SPS). SPS experiments performed at 650 °C with sintering times ranging from 5 to 45 min under a pressure of 100 MPa, yielded to dense bulk nanostructured cobalt (relative density greater than 97%). X-ray diffraction patterns of the as-prepared powders showed only a face centered cubic (fcc) crystalline phase, whereas the consolidated samples exhibited a mixture of both fcc and hexagonal close packed (hcp) phases. Transmission electron microscopy observations revealed a lamellar substructure with a high density of nanotwins and stacking faults in every grain of the sintered samples. Room temperature compression tests, carried out at a strain rate of 10{sup −3} s{sup −1}, yielded to highest strain to fracture values of up to 5% for sample of holding time of 15 min, which exhibited a yield strength of 1440 MPa, an ultimate strength as high as 1740 MPa and a Young's modulus of 205 GPa. The modulus of elasticity obtained from the nanoindentation tests, ranges from 181 to 218 GPa. The lowest modulus value of 181 GPa was obtained for the sample with the highest sintering time (45 min), which could be related to mass density loss as a consequence of trapped gases releasing. - Highlights: • Co nanopowder (50 nm) was prepared by reduction in polyol medium. • SPS was used to process bulk nanostructured Co specimens. • Microstructures were made of intricate fcc/hcp, along with nanotwins and SFs. • High strengths and moderate compressive ductility were obtained. • Deformation mechanisms related to complex interplay of different length scales.

36 MATERIALS SCIENCE↗

Mechanical and tribological property comparison of melt-compounded nanocomposites of atomic-layer-deposition-coated polyamide particles and commercial nanofillers

Mechanical and tribological properties of melt-compounded titanium dioxide nanocomposites of atomic-layer-deposition (ALD)-coated polyamide particles and commercial nanofillers were compared. The nanofiller dispersion in the polyamide matrix was studied using transmission electron microscopy showing very different morphology for the ALD-created and the traditional nanocomposites: former appearing as ribbons in the matrix whereas latter composing from spherical clusters. The effect of such morphology change on the specimen's mechanical response subjected to tensile and impact loading was investigated. The results demonstrated that ALD-created nanocomposites possess significantly higher Young's modulus than pure and traditionally filled polyamide matrix. However, transition from ductile to brittle behavior occurs especially for the ALD-created nanocomposites. Notched impact strength experiments supported this, suggesting that the impact strength of ALD-created composites decreased significantly compared to pure polyamide matrix, whereas traditionally melt-compounded nanocomposites showed no significant changes. Furthermore, the tribological properties of the selected specimens were determined and the effect of the nanofiller on the friction and scratching properties of the polyamide matrix is discussed.

36 MATERIALS SCIENCE↗

A two-set order parameters phase-field modeling of crack deflection/penetration in a heterogeneous microstructure

Modeling of crack deflection/penetration or manifested as intergranular/transgranular fracture in polycrystals has long been a challenge in both fracture mechanics and materials science. A phase-field model formulated with two-set order parameters describing the crack field and the microstructure field respectively, is herein established to investigate the competition between crack penetration and deflection at an interface. The advantages of the proposed model are three-fold: (1) the fracture toughness of grain boundaries and/or interfaces, besides single crystal properties (e.g., Young’s modulus, Poisson ratio, and fracture toughness), can be automatically incorporated, (2) cohesive interfaces are treated in one phase-field framework in comparison with the integrated phase-field and cohesive zone model in which cohesive elements have to be manually placed at the interface, and (3) two-set order parameters enable to describe the concurrent crack propagation and microstructure evolution. The proposed model is validated by comparing the simulated critical deflection angles with the results from theoretical analysis of the linear elastic fracture mechanics and the experiments. The model is then applied to a heterogeneous Silicon Nitride polycrystal to determine the effect of interface fracture toughness on the intergranular/transgranular fracture transition and the effective toughness of the materials.

Chen, Hu↗

High modulus invert analog glass compositions containing beryllia

Glass compositions having a Young's modulus of at least 15 million psi and a specific modulus of at least 110 million inches consisting essentially of, in mols, 10-45% SiO2, 2-15% Li2O, 3-34% BeO, 12-36% of at least one bivalent oxide selected from the group consisting of CaO, ZnO, MgO and CuO, 10-39% of at least one trivalent oxide selected from the group consisting of Al2O3, B2O3, La2O3, Y2O3 and the mixed rare earth oxides, the total number of said bivalent and trivalent oxides being at least three, and up to 10% of a tetravalent oxide selected from the group consisting of ZrO2, TiO2 and CeO2.

Bacon, J. F.↗

Finite elements modelling of scattering problems for flexural waves in thin plates: Application to elliptic invisibility cloaks, rotators and the mirage effect

We propose a finite elements algorithm to solve a fourth order partial differential equation governing the propagation of time-harmonic bending waves in thin elastic plates. Specially designed perfectly matched layers are implemented to deal with the infinite extent of the plates. These are deduced from a geometric transform in the biharmonic equation. To numerically illustrate the power of elastodynamic transformations, we analyze the elastic response of an elliptic invisibility cloak surrounding a clamped obstacle in the presence of a cylindrical excitation i.e. a concentrated point force. Elliptic cloaking for flexural waves involves a density and an orthotropic Young's modulus which depend on the radial and azimuthal positions, as deduced from a coordinates transformation for circular cloaks in the spirit of Pendry et al. [Science 312, 1780 (2006)], but with a further stretch of a coordinate axis. We find that a wave radiated by a concentrated point force located a couple of wavelengths away from the cloak is almost unperturbed in magnitude and in phase. However, when the point force lies within the coating, it seems to radiate from a shifted location. Finally, we emphasize the versatility of transformation elastodynamics with the design of an elliptic cloak which rotates the wavevector of a flexural wave within its core.

97 MATHEMATICS AND COMPUTING↗

Mechanically induced self-propagating reaction and consequent consolidation for the production of fully dense nanocrystalline Ti{sub 55}C{sub 45} bulk material

We employed a high-energy ball mill for the synthesis of nanograined Ti{sub 55}C{sub 45} powders starting from elemental Ti and C powders. The mechanically induced self-propagating reaction that occurred between the reactant materials was monitored via a gas atmosphere gas-temperature-monitoring system. A single phase of NaCl-type TiC was obtained after 5 h of ball milling. To decrease the powder and grain sizes, the material was subjected to further ball milling time. The powders obtained after 200 h of milling possessed spherical-like morphology with average particle and grain sizes of 45 μm and 4.2 nm, respectively. The end-products obtained after 200 h of ball milling time, were then consolidated into full dense compacts, using hot pressing and spark plasma sintering at 1500 and 34.5 MPa, with heating rates of 20 °C/min and 500 °C/min, respectively. Whereas hot pressing of the powders led to severe grain growth (∼ 436 nm in diameter), the as-spark plasma sintered powders maintained their nanograined characteristics (∼ 28 nm in diameter). The as-synthesized and as-consolidated powders were characterized, using X-ray diffraction, high-resolution electron microscopy, and scanning electron microscopy. The mechanical properties of the consolidated samples obtained via the hot pressing and spark plasma sintering techniques were characterized, using Vickers microhardness and non-destructive testing techniques. The Vickers hardness, Young's modulus, shear modulus and fracture toughness of as-spark plasma sintered samples were 32 GPa, 358 GPa, 151 GPa and 6.4 MPa·m{sup 1/2}, respectively. The effects of the consolidation approach on the grain size and mechanical properties were investigated and are discussed. - Highlights: • Room-temperature synthesizing of NaCl-type TiC • Dependence on the grain size on the ball milling time • Fabrication of equiaxed nanocrystalline grains with a diameter of 4.2 nm • Fabrication of nanocrystalline bulk TiC material by SPS with minimal grain growth • Dependence of improved mechanical properties on the consolidation techniques.

36 MATERIALS SCIENCE↗

Operational and Compositional Factors that Affect the Performance Properties of ARP/MCU Saltstone Grout

The Saltstone Production Facility (SPF) receives low level waste (LLW) salt solution from Tank 50H for treatment and disposal. Tank 50H receives transfers from the Effluent Treatment Project (ETP), the H-Canyon General Purpose Evaporator, and the Actinide Removal Process/Modular Caustic Side Solvent Extraction Unit (ARP/MCU) Decontaminated Salt Solution Hold Tank (DSS-HT). At the SPF, the LLW is mixed with premix (a cementitious mixture of portland cement (PC), blast furnace slag (BFS) and Class F fly ash (FA)) in a Readco mixer to produce fresh (uncured) saltstone that is transferred to the Saltstone Disposal Facility (SDF) vaults. The saltstone formulation (mix design) must produce a grout waste form that meets both placement and performance properties. In previous simulated saltstone studies, multiple compositional factors were identified that drive the performance properties of saltstone made from the projected ARP/MCU salt solution. This composition was selected as salt solution simulant since ARP/MCU is the primary influent into Tank 50H. The primary performance property investigated was hydraulic conductivity since it is a variable input property to the saltstone Performance Assessment (PA) transport model. In addition, the porosity, also referred to as void structure, is another variable that impacts the PA response. In addition, Young's modulus and cured density are other performance properties analyzed in this report; however they are indicators of the performance of saltstone and not direct inputs into the PA. The data from previous studies showed that the largest impact on the performance properties of saltstone was due to curing temperature, followed by aluminate concentration in the salt solution, water to premix ratio and premix composition. However, due to the scope of the previous studies, only a few mixes were cured and analyzed at higher temperatures. The samples cured at 60°C had an increased hydraulic conductivity of approximately 600 times that of the sample cured at room temperature. The hydration reactions initiated during the mixing of the premix and salt solution continue during the curing period in the vaults to produce the hardened waste form product. The heat generated from exothermic hydration reactions results in a temperature increase in the vaults that depends on the composition of the decontaminated salt solution being dispositioned, the grout formulation (mix design) and the pour frequency and volume. This heat generation is a contributing factor to the temperature increase in the vaults that leads to an increased cure temperature for the grout. This report will further investigate the impact of curing temperature on saltstone performance properties (hydraulic conductivity, Young's modulus, porosity, etc.) over a range of aluminate concentration, water to premix (w/p) ratio and weight percent fly ash in the premix processed at the SPF. The three curing temperatures selected for this study were chosen to provide data at fixed cure temperatures that represent measured temperatures in the SDF vaults. This does not represent the conditions in the vault where the temperature of the saltstone is continually changing with time. For example, it may take several days for the saltstone to reach 60°C at a given elevation. Previous results demonstrated that the rates at which a selected curing temperature is reached affect the performance properties. The approach taken in this task, a rapid increase to the curing temperature, may be conservative with respect to decreased performance. Nevertheless, the data will provide a basis from which to determine the impact of curing temperature on saltstone performance as a function of key variables. A statistical evaluation of the results for these mixes will be performed to provide the range, and associated uncertainties, of hydraulic conductivity and other properties over this factor space.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Structure and properties of ZrN coatings deposited by high power impulse magnetron sputtering technology

Monolayer ZrN coatings were deposited exclusively by the novel high power impulse magnetron sputtering (HIPIMS) technology in an industrial scale physical vapour deposition (PVD) machine (HTC-1000-4 target system). Coatings were deposited on 1 {mu}m polished M2 high speed steel, on 304L stainless steel (SS), and on Si (100) specimens. Prior to deposition, HIPIMS plasma sustained on a zirconium (Zr) target was utilized to pretreat the specimens. Coatings were deposited at 400 deg. C in a mixed N{sub 2} and Ar atmosphere using 2 magnetrons in HIPIMS mode and at three different substrate bias voltages (U{sub bias}) keeping all other process parameters constant. The thicknesses of the coatings measured by the ball cratering technique were in the ranges of 1.84, 1.96, and 2.13 {mu}m at bias voltages of -95, -75, and -65 V, respectively, where the difference in thickness can be attributed to the resputtering effect. X-ray diffraction experiments on SS specimens revealed a dominating 111 texture for all three coatings irrespective of the bias voltage. Cross-sectional transmission electron microscopy revealed extremely dense coating structures at all bias voltages, similar to the transition zone structure (zone T) reported by Thornton. The -95 bias voltage coatings appeared extremely smooth on the top and with no dome shaped structures often associated with low ion bombardment during deposition. HIPIMS pretreatment leads to high adhesion (L{sub C}) of the coatings to the substrate. A continuous ductile perforation of the coating was observed at progressive loads greater than 65 N; however, no spallation of the coating was observed up to loads of 100 N. High values of hardness (40.4 GPa), Young's modulus (424 GPa), and compressive stress (10 GPa) were recorded for coatings deposited at -95 BV. The hardness and internal stress of the coating were found increasing with more negative bias voltages. All the coatings exhibited high dry sliding wear resistance (K{sub C}) in the range 6x10{sup -15} m{sup 3} N{sup -1} m{sup -1}. Cross-sectional transmission electron microscopy and atomic force microscopy analyses have been used to study the effect of ion bombardment obtained from HIPIMS on the structure of the coatings.

36 MATERIALS SCIENCE↗