Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Waste Repository”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Experimental Investigation of Two-Phase Flow in Consolidating and Intact Salt: Analysis of Capillary Pressure Measurements from Core Labs

Two-phase flow of brine and air through very low permeability porous media is the dominant fluid flow state in and around geologic repositories for nuclear waste disposal. Constitutive models developed for other subsurface media (shale, sandstone, limestone, etc.) have been adopted but never experimentally parameterized for geologic salt. This report summarizes results of scoping capillary pressure and brine saturation measurements on reconsolidated run-of-mine salt and intact geologic salt samples. These measurements were obtained using mercury injection tests and yielded values of threshold pressure, pore-size distribution, and mercury saturation. The brine capillary pressure curve was then inferred from the raw mercury capillary pressure data. This report also summarizes estimates of the constitutive model parameters from the brine saturation and capillary pressure data (Brooks and Corey, 1964; van Genuchten, 1980). The results suggests that the model of van Genuchten (1980) is better suited for brine-air-salt systems. Additional testing is needed for the low brine saturation range of the capillary pressure curve where the present suite of tests did not yield sufficient data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2015

Investigation of Coupled Processes and Impact of High Temperature Limits in Argillite Rock

The focus of research within the UFD Campaign is on repository-induced interactions that may affect the key safety characteristics of an argillaceous rock. These include thermal-hydrological-mechanical-chemical (THMC) process interactions that occur as a result of repository construction and waste emplacement. Some of the key questions addressed in this report include the development of fracturing in the excavation damaged zone (EDZ) and THMC effects on the near-field argillaceous rock and buffer minerals and petrophysical characteristics, particularly the impacts of induced temperature rise caused by waste heat.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2016

Characterization of Reconsolidated Crushed Salt from the BAMBUS Site.

Observational petrofabrics, thermal, mechanical, and hydrological measurements were made on reconsolidated salt samples extracted from the field site in which a study called Backfilling and Sealing of Underground Repositories for Radioactive Waste in Salt was conducted. Similar characterization was completed more than a decade ago, so this work furthers previous measurements after sustained consolidation in situ . Porosity determined by traditional point-counting on polished sections and helium porosimeter methods ranged from 20-25% with consolidation governed by brittle processes, as evidence of fluid-aided, grain-boundary processes was rarely observed. Thermal conductivity in the range of 2.3 W /( m * K ) is consistent for granular halite in this porosity range. Gas flow measurements yielded permeability of the order of 5e -13 m 2 . Pressure-sensitive compressive strengths at 0.5, 1.0, and 2.0 MPa confining pressure were 8, 9, and 14 MPa, respectively, with apparent elastic moduli increase with deformation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2016

Characterization of Reconsolidated Crushed Salt from the BAMBUS Site

Observational petrofabrics, thermal, mechanical, and hydrological measurements were made on reconsolidated salt samples extracted from the field site in which a study called Backfilling and Sealing of Underground Repositories for Radioactive Waste in Salt was conducted. Similar characterization was completed more than a decade ago, so this work furthers previous measurements after sustained consolidation in situ . Porosity determined by traditional point-counting on polished sections and helium porosimeter methods ranged from 20-25% with consolidation governed by brittle processes, as evidence of fluid-aided, grain-boundary processes was rarely observed. Thermal conductivity in the range of 2.3 W/(m∙K) is consistent for granular halite in this porosity range. Gas flow measurements yielded permeability of the order of 5e- 13 m 2 . Pressure-sensitive compressive strengths at 0.5, 1.0, and 2.0 MPa confining pressure were 8, 9, and 14 MPa, respectively, with apparent elastic moduli increase with deformation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2019

Mathematical Modelling of Fault Reactivation Induced by Water Injection

Faults in the host rock that might exist in the vicinity of deep geological repositories for radioactive waste, constitute potential enhanced pathways for radionuclide migration. Several processes might trigger pore pressure increases in the faults leading to fault failure and induced seismicity, and increase the faults’ permeability. In this research, we developed a mathematical model to simulate fault activation during an experiment of controlled water injection in a fault at the Mont-Terri Underground Research Laboratory in Switzerland. The effects of in-situ stress, fault shear strength parameters and heterogeneity are assessed. It was shown that the above factors are critical and need to be adequately characterized in order to predict the faults’ hydro-mechanical behaviour.

58 GEOSCIENCES↗
DOE OSTI2021

Compaction of crushed salt for safe containment – overview of the KOMPASS project

Abstract. In Germany, rock salt formations are possible host rock candidates for a repository for heat-emitting radioactive waste. The safety concept of a repository in salt bases on a multibarrier system consisting mainly of the geological barrier salt and geotechnical seals ensuring safe containment. Crushed salt will be used for backfilling of cavities and sealing measures in drifts and shafts due to its favourable properties and its easy availability (mined-off material). The creep of the rock salt leads to crushed salt compaction with time. Thereby, the crushed salts' porosity is reduced from the initial porosity of 30 %–40 % to a value comparable to the porosity of undisturbed rock salt (≤1 %). In such low porosity ranges, technical impermeability is assumed. The compaction behaviour of crushed salt is rather complex and involves several coupled THM processes (Kröhn et al., 2017; Hansen et al., 2014). It is influenced by internal properties like humidity and grain size distribution, as well as boundary conditions such as temperature, compaction rate or stress state. However, the current process understanding has some important gaps referring to the material behaviour, experimental database and numerical modelling. It needs to be extended and validated, especially in the low porosity range. The objective of the KOMPASS project was development of methods and strategies for the reduction of deficits in the prediction of crushed salt compaction leading to an improvement of the prognosis quality. Key results are as follows (KOMPASS Phase 1, 2020): selection of an easily available and permanently producible synthetic crushed salt mixture, acting as a reference material for generic investigations; development and proof of different techniques for producing pre-compacted samples for further investigations; establishment of a tool of microstructure investigation methods to demonstrate the comparability of grain structures of pre-compacted samples with in-situ compacted material for future investigations; execution of various laboratory experiments using pre-compacted samples, e.g. long-term creep tests which deliver reliable information about time- and stress-dependent compaction behaviour; development of a complex experimental investigation strategy to derive necessary model parameters considering individual functional dependencies. Its technical feasibility was successfully verified; benchmarking with various existing numerical models using datasets from three different triaxial long-term tests. The result was not entirely satisfactory; however, the number of influencing factors is small and further validation work has to be done. Overall, the KOMPASS project has made significant progress in the approaches to solving the outstanding question, building the basis for further investigations.

Friedenberg, Larissa↗
DOE OSTI2018

Geochemical Simulations of Plutonium Redox Speciation at Increasing Ionic Strengths - 18567

In salt repositories like the Waste Isolation Pilot Plant (WIPP), reducing conditions are expected, supporting two aqueous species of plutonium: Pu(III) and Pu(IV). Of these states, Pu(III) is more soluble than Pu(IV). Because Pu behavior is uncertain in WIPP brines under reducing conditions, performance assessment calculations assume a 50/50 partitioning between the two, justified through calculations using dilute solutions. Recent experimental evidence suggests an increasing importance for Pu(III). To reexamine this assumption, we modeled Pu speciation in NaCl and dilute WIPP brine solutions equilibrated with a Pu solid, including PuO{sub 2} and Pu(OH){sub 3}. To maintain reducing conditions, sulfate and sulfide were added. Models were performed using PHREEQC and the Specific Ion Theory (SIT) database on dilutions ranging from 0.1 M to 3 M. Models were compared to calculations using the Pitzer database with PuO{sub 2} and with analogs Am(III) and Th(IV), all up to 11 M. Results indicate that under reducing conditions, Pu(III) concentrations increase with ionic strength and can be up to 80 fold higher than Pu(IV). While concentrations varied due to differences in solubility for each solid, Pu(IV) concentrations remained nearly constant in all solutions. Analogs showed similar trends, though Am(III) is 3 times more soluble than Pu(III) while Th(IV) is 6 times more soluble than Pu(IV). Pu(IV) concentrations using Pitzer calculations were similar to those with SIT. Our study indicates that assuming equivalent partitioning of Pu species may under-represent concentrations during a release. They also show that in PA calculations there is a need to consider redox state at high ionic strength rather than adopting an assumption of equal partitioning between the two charges. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2015

Technetium Incorporation in Glass for the Hanford Tank Waste Treatment and Immobilization Plant

A priority of the United States Department of Energy (U.S. DOE) is to dispose of nuclear wastes accumulated in 177 underground tanks at the Hanford Nuclear Reservation in eastern Washington State. These nuclear wastes date from the Manhattan Project of World War II and from plutonium production during the Cold War. The DOE plans to separate high-level radioactive wastes from low activity wastes and to treat each of the waste streams by vitrification (immobilization of the nuclides in glass) for disposal. The immobilized low-activity waste will be disposed of here at Hanford and the immobilized high-level waste at the national geologic repository. Included in the inventory of highly radioactive wastes is large volumes of 99Tc (~9 × 10E2 TBq or ~2.5 × 104 Ci or ~1500 kg). A problem facing safe disposal of Tc-bearing wastes is the processing of waste feed into in a chemically durable waste form. Technetium incorporates poorly into silicate glass in traditional glass melting. It readily evaporates during melting of glass feeds and out of the molten glass, leading to a spectrum of high-to-low retention (ca. 20 to 80%) in the cooled glass product. DOE-ORP currently has a program at Pacific Northwest National Laboratory (PNNL), in the Department of Materials Science and Engineering at Rutgers University and in the School of Mechanical and Materials Engineering at Washington State University that seeks to understand aspects of Tc retention by means of studying Tc partitioning, molten salt formation, volatilization pathways, and cold cap chemistry. Another problem involves the stability of Tc in glass in both the national geologic repository and on-site disposal after it has been immobilized. The major environmental concern with 99Tc is its high mobility in addition to a long half-life (2.1×105 yrs). The pertechnetate ion (TcO4-) is highly soluble in water and does not adsorb well onto the surface of minerals and so migrates nearly at the same velocity as groundwater. Long-term corrosion of glass waste forms is an area of current interest to the DOE, but attention to the release of Tc from glass has been little explored. It is expected that the release of Tc from glass should be highly dependent on the local glass structure as well as the chemistry of the surrounding environment, including groundwater pH. Though the speciation of Tc in glass has been previously studied, and the Tc species present in waste glass have been previously reported, environmental Tc release mechanisms are poorly understood. The recent advances in Tc chemistry that have given rise to an understanding of incorporation in the glass giving rise to significantly higher single-pass retention during vitrification are presented. Additionally, possible changes to the baseline flowsheet that allow for relatively minor volumes of Tc reporting to secondary waste treatment will be discussed.

Kruger, Albert A.↗
DOE OSTI2015

Technetium incorporation in glass for the Hanford Tank Waste treatment and immobilization plant - 15066

A priority of the United States Department of Energy (U.S. DOE) is to dispose of nuclear wastes accumulated in 177 underground tanks at the Hanford Nuclear Reservation in eastern Washington State. These nuclear wastes date from the Manhattan Project of World War II and from plutonium production during the Cold War. The DOE plans to separate high-level radioactive wastes from low activity wastes and to treat each of the waste streams by vitrification (immobilization of the nuclides in glass) for disposal. The immobilized low-activity waste will be disposed of here at Hanford and the immobilized high-level waste at the national geologic repository. Included in the inventory of highly radioactive wastes is large volumes of {sup 99}Tc (∼9 x 10 E2 TBq or ∼2.5 x 10{sup 4} Ci or ∼1500 kg). A problem facing safe disposal of Tc-bearing wastes is the processing of waste feed into in a chemically durable waste form. Technetium incorporates poorly into silicate glass in traditional glass melting. It readily evaporates during melting of glass feeds and out of the molten glass, leading to a spectrum of high-to-low retention (ca. 20 to 80%) in the cooled glass product. DOE-ORP currently has a program at Pacific Northwest National Laboratory (PNNL), in the Department of Materials Science and Engineering at Rutgers University and in the School of Mechanical and Materials Engineering at Washington State University that seeks to understand aspects of Tc retention by means of studying Tc partitioning, molten salt formation, volatilization pathways, and cold cap chemistry. Another problem involves the stability of Tc in glass in both the national geologic repository and on-site disposal after it has been immobilized. The major environmental concern with {sup 99}Tc is its high mobility in addition to a long half-life (2.1 x 10{sup 5} yrs). The pertechnetate ion (TcO{sup 4-}) is highly soluble in water and does not adsorb well onto the surface of minerals and so migrates nearly at the same velocity as groundwater. Long-term corrosion of glass waste forms is an area of current interest to the DOE, but attention to the release of Tc from glass has been little explored. It is expected that the release of Tc from glass should be highly dependent on the local glass structure as well as the chemistry of the surrounding environment, including groundwater pH. Though the speciation of Tc in glass has been previously studied, and the Tc species present in waste glass have been previously reported, environmental Tc release mechanisms are poorly understood. The recent advances in Tc chemistry that have given rise to an understanding of incorporation in the glass giving rise to significantly higher single-pass retention during vitrification are presented. Additionally, possible changes to the baseline flowsheet that allow for relatively minor volumes of Tc reporting to secondary waste treatment will be discussed. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Evaluation of desiccation cracking characteristics of inorganic micro-fiber-reinforced engineered barrier material (IMEBM) for geological repository

Abstract Buffer material is crucial for the engineering barrier system to dispose of high-level radioactive waste in a geological repository. A reliable buffer material should be able to maintain good sealing characteristics and minimize desiccation cracking. In this study, the effectiveness of inorganic fiber-reinforced engineering barrier material in reducing desiccation cracks in bentonite was evaluated via desiccation tests, image analysis, and air permeability tests. The effects of fiber type (E-glass fiber and basalt fiber) and fiber content (0.0%, 0.5%, 1.0%, 1.5%, 3.0%, and 5.0% of dry weight of the bentonite) on the development of desiccation cracks in the fiber–bentonite mixtures with the same given initial moisture content were evaluated. The results indicated that the addition of fibers could significantly reduce the crack size and area in bentonite during the drying. Basalt fibers showed a slightly better reinforcement effect than E-glass fibers when the fiber content was lower than 3.0%. The addition of fibers prevented the development of penetrating cracks and significantly reduced the permeability of the bentonite after drying. The permeabilities of basalt fiber- and E-glass fiber-reinforced bentonite composites with 3% reinforcement were 5.81 × 10 –11 m 2 and 7.24 × 10 –11 m 2 , respectively, which were 64 and 51 times smaller than that of pure bentonite. X-ray–CT observation of the internal structure of the samples after drying showed that the addition of fibers significantly changed the crack morphology and potentially increased the tortuosity.

Feng, Yuan↗
DOE OSTI2026

Improbability of Post-Closure Criticality in Compacted Criticality Control Overpacks after Room Closure at Waste Isolation Pilot Plant

As part of its periodic re-certification of the Waste Isolation Pilot Plant (WIPP), an operating repository in bedded salt for the disposal of transuranic (TRU) waste from atomic energy defense activities, the United States Environmental Protection Agency expects a re-evaluation of features, events, and processes, such as post-closure nuclear criticality. Although salt creep beneficially encapsulates the TRU waste in the closed WIPP repository, the spacing between an array of waste packages is disrupted as the salt creep closes disposal rooms and containers lose structural integrity. For most TRU waste, the possibility of post-closure criticality is exceedingly small either because the salt neutronically isolates TRU waste canisters or because closure of a disposal room from salt creep does not sufficiently compact the low mass of fissile material. The criticality evaluation was updated, however, because of the introduction of criticality control overpack (CCO) containers, which may dispose up to 380 fissile gram equivalent plutonium-239 in each container. The criticality potential is evaluated through high-fidelity geomechanical modeling of a disposal room filled with CCO containers during two representative conditions: (1) large salt block fall, and (2) gradual disposal room closure from salt creep. Geomechanical models of roof fall demonstrate three tiers of CCO containers are not greatly disrupted. Geomechanical models of gradual room closure from salt creep (without brine seepage and subsequent gas generation to permit maximum room closure) were used to predict irregular arrays of closely packed CCOs after 1000 years, when room closure has asymptotically approached maximum compaction. Models of spheres or cylinders with 380 fissile gram equivalent of plutonium (as oxide) at the predicted irregular compacted spacing demonstrate that an array of CCO containers is not critical when surrounded by salt and magnesium oxide, provided the mass of hydrogenous material shipped in CCO containers (usually plastics) is controlled or boron carbide (a neutron poison) is mixed with the fissile contents.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2015

German research and development for high level waste in light of the new site selection process - 15516

The German government decided 50 years ago, that radioactive waste is to be disposed of in Deep Geologic Repositories, preferably in a salt rock formation. Soon after, in 1967, research in the Asse salt mine was initiated. Since then substantial progress has been achieved in the development of the radioactive waste disposal programme in Germany. For a geologic repository for High Level Waste in salt a reference concept has been developed, which represented the radioactive waste management processes from transport of High Level Waste and Spent Nuclear Fuel to an interim storage site, waste conditioning and repackaging for disposal, to emplacement of the waste packages. The feasibility of the reference concept has been proven by demonstration tests for all relevant equipment: a pilot conditioning plant has been built as well as the main equipment for the entire transport chain including the shaft transport and emplacement technologies for heavy loads fulfilling strict requirements for nuclear and mining safety. Also the backfilling technology has been optimised for the purposes of a repository for radioactive waste. Finally, tests have been performed to verify thermo-mechanical models for the host rock. The demonstration tests have been performed to an extent which even would allow immediate licensing of the repository and the employed equipment. The Research and Development work was completed by further optimisation of the reference concept. Construction and operation of deep geologic repositories for low and intermediate level radioactive wastes in Germany benefited from the above mentioned but also stimulated the knowledge and experience build-up for the repositories for High Level Waste. Despite the well progressed work for a deep geologic repository in salt R and D work in Germany for already a long time also considered other host rock formations. While work for crystalline rock mainly consisted of relatively small contributions to international research projects due to the limited occurrence of suitable sites in Germany, projects and developments for repositories in clay formations have had an increasing contribution to the overall Research and Development work for radioactive waste repositories in Germany. In July 2013 a new site selection act was put into force, which set the initiating conditions for the German programme on radioactive waste management. Principally, a process was initiated to search for a site for a deep geologic repository for High Level Waste independent from earlier decisions. This means that a site shall be determined without predetermination by earlier decisions. Nevertheless, to enable a sound decision for a site selection it is necessary to be able draw back on the knowledge and experience from earlier activities. Otherwise, tedious learning processes would have to be experienced again. Since efforts to open up a site selection process again grew since the late 1990's projects had been implemented timely to capture existing knowledge. The paper at hand describes the achievements of R and D activities in Germany, the change of radioactive waste management policy and the endeavours to maintain the achievements. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Epsilon Metal: A Waste Form for Noble Metals from Used Nuclear Fuel

Epsilon metal (e-metal) is the metallic phase that forms as inclusions at the grain boundaries in the UO2 fuel during reactor operation. This metal is composed of Pd, Mo, Rh, Ru, and Tc. These metallic inclusions are insoluble in strong acid and remnants of these metallic inclusions have been found in the UO2 matrix that remains from the natural reactors in Gabon that were active 1.8 billion years ago, therefore e-metal should be an excellent waste form for the immobilization of the long-lived isotopes 107Pd (6.5 ? 106 a) and 99Tc (2.13 ? 105 a), with 99Tc being the isotope of interest for repository performance. Therefore, the chemical durability of this potential waste form is assessed in this study. Typically, corrosion rates for metallic materials are measured electrochemically because they are quick, inexpensive, and can reveal the mechanism by which a metal corrodes, at least initially. However, in a repository the waste form would be subjected to slowly flowing water without an applied electrical potential over long time periods. Therefore, the corrosion rates of e-metal specimens were measured with both electrochemical tests and the single-pass flow-through test (SPFT). Potentiodynamic and potentiostatic polarization results suggest that a thin passive film exists on the alloy surface, which seems to be responsible for its high corrosion resistance. Additionally, X-Ray photoelectron spectroscopic results suggest that Pd oxides are significantly enriched in the passive film Results from the SPFT show that the dissolution rates were weakly dependent on pH. Only Mo and Re were found in solution and were used for the calculation of the dissolution rates. In general, the electrochemically determined corrosion rates agree reasonably well with the initial dissolution rate measured with the SPFT test, but they are about one or two orders of magnitude higher than the steady state rates. The causes for this discrepancy are discussed.

epsilon-metal, nuclear waste form, corrosion, sing↗
DOE OSTI2019

Panel Session 3: Featured Country Canada: Management and Disposal of High and Low-Level Waste

This panel featured Senior Executives accountable for the safe management and disposal of most of Canada's radioactive waste liabilities and provided their perspectives on current plans and progress made to date. Topics addressed by the panelists included national policies and programs, the regulatory framework, and actions led by the waste generators and solution implementers to ensure Canada's waste legacy is responsibly managed. Presentations proposed include: 1 - Overview of Canadian Radioactive Waste Policy and Long-Term Waste Management Projects (Dave McCauley, Natural Resources Canada (Canada)); 2 - Featured Country: Canada - National Repository (Laurie Swami, Nuclear Waste Management Organization (Canada)); 3 - Management and Disposal of Ontario Power Generation's Low and Intermediate Level Waste (Lise Morton, Ontario Power Generation (Canada)); 4 - Featured Country: Canada - National Laboratories Liabilities (Richard Sexton, Atomic Energy of Canada Limited (Canada)); 5 - Management and Disposal of High and Low-Level Waste (Mark Lesinski, Canadian Nuclear Laboratories (Canada)); 6 - Disposal in Canada: The Regulatory Perspective (Ramzi Jammal, Canadian Nuclear Safety Commission (Canada))

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2016

Design and Construction of a Loess-Cement Cushion as an Integral Component of an SL-LILW Repository - 16077

The Bulgarian State Enterprise for Radioactive Waste Management (SERAW) is planning the construction of a near-surface repository for short-lived low and intermediate level radioactive waste, the National Disposal Facility (NDF), adjacent to the Kozloduy Nuclear Power Plant (KNPP). The NDF will be constructed as a reinforced concrete vault-type repository system, where prefabricated cubic waste packages (2 m on a side) will be emplaced in large reinforced concrete disposal cells. Waste emplacement operations will be conducted in three phases over a total of 60 years of operations. After the last waste packages have been disposed, an engineered multilayer cover will be installed over the site to further isolate the waste from the accessible environment. The Radiana Site where the NDF will be constructed is a sloping area located between the second and sixth loess terraces above the River Danube with elevations ranging from approximately +40 m to elevation +95 m. The unsaturated zone at the location selected for waste disposal ranges from 13 m to 16 m in thickness. After construction, the unsaturated zone will consist of a 5 m thick, engineered loess-cement cushion installed over naturally occurring Pliocene clays and sandy clayey sediments of the Brusarci Formation with a thickness above the top of groundwater ranging from 8 m to 11 m. The loess-cement cushion is a key component of the 'engineered fill' barrier as identified in the Intermediate Safety Assessment Report (ISAR) for the NDF. This barrier consists of engineered fill both below the disposal cells, i.e., the loess-cement cushion, and above the disposal cells, i.e. the final multilayer cover to be installed at closure of the facility. The loess-cement cushion component of this barrier will act to provide a geo-technically stable foundation for the disposal system. In addition, the barrier will raise the base of the disposal cells and increases the unsaturated zone thickness above the top of the groundwater table, as well as to serve as a chemical barrier that will act to sorb radionuclides thereby retarding their migration to the underlying groundwater. In addition to its assigned barrier functions the loess cement cushion also houses key embedded components required as part of the overall NDF safety concept, including systems necessary for operational and post-closure performance monitoring as well as the support foundation structures required for the mobile roofs, which are designed to handle and protect the waste during emplacement operations. The post-closure monitoring period, i.e., the period of institutional control, is given by as 300 years. While similar although less massive cushions have been previously constructed as foundations for various structures at the KNPP, the loess-cement cushion planned for construction at the NDF including the embedded structures will represent a first of its kind construction in terms of both its physical dimensioning as well as its requirements for long-term performance. This paper describes the design of the cushion, its functions and its construction as planned for the NDF as an integral component of the site safety concept. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2016

Developing a New National Programme and Implementation Plan for the Management and Disposal of Spent Fuel and Radioactive Wastes in Romania - 16391

The European 'Waste Directive' (2011/70/Euratom) required each Member State to report by August 2015 on their National Programme for management of spent fuel and radioactive wastes. In Romania, the Nuclear Agency (ANDR) was responsible for preparing the National Programme report, and this was done in a step-wise manner that involved the regulators and waste producers. The starting point for the process was an assessment of existing policy against the evolving situation in the nuclear sector in the country, most notably the decision to progress with the construction of two new CANDU reactors. The final agreed National Programme report submitted to the European Commission describes the activities currently undertaken to manage spent fuel and radioactive wastes in Romania. The report also sets out, at a high-level, the additional activities that will need to be taken in the future (and an indicative timeline), including those steps that will be required to implement a new surface repository for short-lived wastes, and a geological repository for spent fuel and long-lived wastes. Additional, on-going work is intended to lead to a revision of Government policy and the development of a more detailed implementation strategy, underpinned by a programme of R and D and robust financing plans. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Past Approaches for Spent Nuclear Fuel, Transuranic, and High-Level Waste Disposal in the United States—Part 2: Siting Process, Staged Development, and Public Preferences

This report presents pertinent aspects of the ~50-year United States experience in siting a mined geologic disposal repository for spent nuclear fuel (SNF), transuranic (TRU) waste, and high-level radioactive waste (HLW) as related to site selection and the staged process for site investigations as specified in the Nuclear Waste Policy Act of 1982 and generic and site-specific regulations of the US Department of Energy (DOE), US Environmental Protection Agency (EPA), and US Nuclear Regulatory Commission (NRC). The roles of the Environmental Impact Statement and guidance in international consensus standards by the International Atomic Energy Agency are also mentioned. The focus is on siting and developing the Waste Isolation Pilot Plant, an operating repository for TRU waste from atomic energy defense activities, and the proposed Yucca Mountain repository for commercial SNF and HLW. In the social dimension, the role of institutional stakeholders is described. Past national surveys related to waste management options for storage and disposal provide insight on public preferences of other stakeholders. The descriptions are intended to help other countries more fully understand the stages adopted for siting and developing repositories in the United States.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2015

Milestones for Selection, Characterization, and Analysis of the Performance of a Repository for Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain.

This report presents a concise history in tabular form of events leading up to site identification in 1978, site selection in 1987, subsequent characterization, and ongoing analysis through 2009 of the performance of a repository for spent nuclear fuel and high - level radioactive waste at Yucca Mountain in southern Nevada. The tabulated events generally occurred in five periods: (1) commitment to mined geologic disposal and identification of sites; (2) site selection and analysis, based on regional geologic characterization through literature and analogous data; (3) feasibility analysis demonstrating calculation procedures and importance of system components, based on rough measures of performance using surface exploration, waste process knowledge, and general laboratory experiments; (4) suitability analysis demonstrating viability of disposal system, based on environment - specific laboratory experiments, in - situ experiments, and underground disposal system characterization; and (5) compliance analysis, based on completed site - specific characterization . The current sixth period beyond 2010 represents a new effort to set waste management policy in the United States. Because the relationship is important to understanding the evolution of the Yucca Mountain Project , the tabulation also shows the interaction between the policy realm and technical realm using four broad categories of events : (a) Regulatory requirements and related federal policy in laws and court decisions, (c) Presidential and agency directives, (c) technical milestones of implementing institutions, and (d) critiques of the Yucca Mountain Project and pertinent national and world events related to nuclear energy and radioactive waste. Preface The historical progression of technical milestones for the Yucca Mountain Project was originally developed for 10 journal articles in a special issue of Reliability Engineering System Safety on the performance assessment for the Yucca Mountain license application [1-10]. The listing of mile stones, a distinct feature of those articles, has been collected and tabulated here. A lthough a brief description is presented here (based on the summaries in the 10 journal articles), the emphasis remains on the tabulation because of its usefulness in providing a comprehensive but concise history of the Yucca Mountain Project. The tabulation presented here is more elaborate than originally presented in that many of the interactions that occurred between the technical realm and policy realm can be depicted in separate columns. The usefulness of the milestones table is due in part to L.A. Connolly, for editorial and reference support, and S.K. Best, Raytheon, and L. Mays, Sandia National Laboratories (SNL), for illustration support. Reviewers P.N. Swift, SNL, and K. Gupta, University of Oklahoma, helped improve the discussion. The historical perspective presented is that of the author and is not necessarily held by reviewers, Sandia National Laboratories , and the US Department of Energy. As a historic perspective, the author is reporting on the work of others; however, any interpretative error s of the documentation are those of the author alone. The characterization and modeling of the Yucca Mountain disposal system required numerous participants with expertise in many areas of science and technology, as evident from the extensive reference list. Their diligent efforts are generally acknowledged here and through the many references to their impressive work, but the 10 journal articles acknowledge by name many of the numerous participants that contributed to the Yucca Mountain Project .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗