Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transformers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

MnBi-based magnets prepared from melt-spun alloys: Effect of $α → β$ phase transformation during field annealing

The temperature of the annealing treatment applied to the MnBi alloys with the intention to stabilize the α -MnBi “low-temperature” phase – a promising material for the rare-earth-free permanent magnets – is usually kept below the range of the β -Mn 1.08 Bi “high-temperature” phase. This work is focused on the investigation of the effects of partial and complete α → β phase transformation in bulk magnetic-field-annealed magnets on their structure and magnetic properties. MnBi alloys modified with In, Mg and Sb were melt-spun, compacted to their full density and then heated in a magnetic field of 30 kOe to temperatures sufficiently high for the beginning of the α → β transformation. A heating of 15 °C/min was used which was immediately followed by cooling at the rate of 7.5 °C/min; the degree of the phase transformation was measured by in situ monitoring of changes in the sample magnetization. In all the studied alloys, the α → β transformation was found to improve the [0 0 1] fiber texture induced by the applied magnetic field, although it simultaneously decreased the coercivity. A partial transformation has resulted in a 11% increase of the maximum energy product for the Mn 50 Bi 49 Sb 0.5 In 0.5 magnet, to 8.3 MGOe, and a 3% increase for the Mn 50 Bi 46 Mg 3 Sb 0.5 In 0.5 magnet, to 12.8 MGOe. In the latter alloy, the α → β and reverse transformations were found to initially occur in well-defined pockets leading to clusters of large, highly textured α crystallites. In the Mn 50 Bi 48.5 Sb 1.5 magnet, only part of the α phase could be recovered after the transformation, which instead promoted the paramagnetic MnBi 0.9 Sb 0.1 phase.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Experimental determination of critical resolved shear stress for strain-induced phase transformation

The current investigation reports the first attempt to measure the critical resolved shear stress to initiates strain-induced phase transformation in a three-dimensional polycrystalline aggregate using high-energy diffraction microscopy (HEDM). In situ tensile testing was performed on a Fe38.5Mn20Co20Cr15Si5Cu1.5 metastable alloy exhibiting transformation-induced plasticity (TRIP). Grains with a higher propensity for strain-induced phase transformation were tracked using HEDM. A sharp drop in grain specific stress, coinciding with the appearance of a new ε-hcp grain oriented relative to the parent γ-fcc phase, was taken as evidence of grain-specific stress required to trigger phase transformation. The highest resolved shear stress on the potential transformation systems was identified as the critical resolved shear stress (CRSS) for strain-induced phase transformation. For the studied metastable alloy, CRSS for transformation was determined to be 86±3 MPa which was very close to theoretical CRSS value determined using Schmid factor (89±12 MPa) compared to the value determined using Taylor factor (62±7 MPa).

Jain, Roopam↗
DOE OSTI2017

A novel rat fibrosarcoma cell line from transformed bone marrow-derived mesenchymal stem cells with maintained in vitro and in vivo stemness properties

Increasing evidence suggests a possible relationship between mesenchymal stem cells (MSCs) and sarcoma. MSCs are hypothesized to be the cells initiating sarcomagenesis, and cancer stem cells (CSCs) sharing features of MSCs have been identified in sarcomas. Here, we report on the characteristics of a bone marrow-derived rat mesenchymal stem cell line that spontaneously transformed in long-term culture. The rat transformed mesenchymal stem cells (rTMSCs) produced soft-tissue fibrosarcomas in immunocompromised mice and immunocompetent rats. In vitro, the rTMSCs displayed increased proliferation capacity compared to the untransformed cell line. The transformed MSCs maintained the mesenchymal phenotype by expression of the stem cell marker CD 90 and the lack of hematopoietic and endothelial markers. Cytogenetic analysis detected trisomy 6 in the rTMSCs. Side population (SP) isolation and tumorsphere cultivation of the transformed cells confirmed the presence of CSCs among the rTMSCs. Importantly, the rTMSCs retained their differentiation capacity towards osteogenic and adipogenic lineages. This transformed MSC-based cell line may be valuable in examining the balance in a mixed cell population between cancer stem cell properties and the ability to differentiate to specific non-transformed cell populations. Moreover, it may also be a useful tool to evaluate the efficacy of novel targeted immunotherapies in vivo. - Highlights: • Spontaneously transformed rat MSCs (rTMSCs) share characteristics with normal MSCs. • rTMSCs possess a side population, enriched with tumorigenic cells. • rTMSCs model fibrosarcoma in vivo.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2019

Martensitic Transformation of Close-Packed Polytypes of Block Copolymer Micelles

Here, we report martensitic shear transformation of strongly segregated block copolymer micelles on face-centered cubic (FCC) lattices to hexagonally close-packed (HCP) structures elucidated by X-ray scattering characterizations. The initial FCC crystal structures of the block copolymer micelles were prepared by direct dissolution of poly(1,2-butadiene-b-ethylene oxide) (PB-PEO) diblock copolymer in the water at 25 °C, and the FCC crystal domains were shear-aligned during the sample preparation process for the X-ray scattering measurements. Heating the shear-aligned FCC crystals of the PB-PEO micelles above 80 °C initiated the transformation to HCP structures, which are also found stable at 25 °C when cooled from the transition temperature. Interestingly, we found that the HCP crystal domains are also aligned, and this suggests that the FCC-to-HCP phase transition has occurred by the martensitic shear transformation. Scattering pattern analysis reveals that the martensitic shear transformation proceeds by preferentially dislocating a specific set of two-dimensional hexagonal close-packed (2D-HCP) layers among four equivalent 2D-HCP layers of the initially shear-aligned FCC crystals. We believe that the selective martensitic shear transformation originates from the orthorhombic-like morphology of the FCC crystal domains formed by slip dislocations and stratifications of initial FCC crystal grains during the sample preparation process. In the shear-aligned FCC crystals with the orthorhombic-like crystal domains, the specific 2D-HCP layers chosen for the martensitic shear transformation have the least area of dislocations, i.e., the least kinetic energy barrier, for the FCC-to-HCP phase transition and appear to be preferentially utilized. These results show that the size and morphology of crystal domains are critical to the formation, stability, and transformation of crystalline structures and consequently control the polymorphism of solid compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mapping the Complete Reaction Energy Landscape of a Metal–Organic Framework Phase Transformation

Crystalline materials undergo valuable phase transformations, and the energetic processes that underlie these transformations can be fully characterized through a combination of thermodynamic and kinetic studies. Here, we report the first complete reaction energy landscape of metal–organic framework (MOF) interpenetration, specifically in the phase transformation of NU-1200 to its doubly interpenetrated counterpart, STA-26. We characterized the thermodynamics of this phase transformation by pairing experiments with density functional theory (DFT) calculations. This analysis revealed that factors such as the increase in crystal density likely drive Zr- and Hf-NU-1200 to STA-26 interpenetration, while other chemical interactions such as steric repulsions prevent Th-NU-1200 from interpenetrating. Using time-resolved in situ X-ray diffraction, we monitored phase transformation reaction profiles and extracted quantitative kinetic information using the Avrami-Erofe’ev model. As a result, we obtained activation energies for the Zr- and Hf-NU-1200 transformations to Zr- and Hf-STA-26, respectively, revealing slower phase change kinetics for MOFs with stronger bonds. Finally, we paired the kinetic data with experimental observations to classify the mechanistic model of this phase transformation as partial dissolution. Here, we anticipate that this thermodynamic, kinetic, and mechanistic understanding will broadly inform further studies on the energetics of crystallization.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Size Transformation of the Au 22 (SG) 18 Nanocluster and Its Surface-Sensitive Kinetics

For many applications of well-defined gold nanoclusters, it is desirable to understand their structural evolution behavior under working conditions with molecular precision. Here we report the first systematic investigation of the size transformation products of the Au 22 (SG) 18 nanocluster under representative working conditions and highlight the surface effect on the transformation kinetics. Under thermal and aerobic conditions, the consecutive and pH-dependent transformation from Au 22 to both well-defined clusters and small Au(I)SR species was identified by ESI-MS and UV-vis spectroscopy. By introducing a perturbation onto the Au 22 surface, significant changes in the activation parameters were determined from the kinetic study of the Au 22 transformation. This indicates the sensitivity of the nanocluster transformation pathway to the cluster surface. Finally, the systematic study of cluster transformation and the sensitivity of cluster transformation to the surface revealed herein has significant implications for future attempts to design gold nanoparticles with adaptation to the working environment and the regeneration of active nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Irradiation-induced β to α SiC transformation at low temperature

Here, we observed that β-SiC, neutron irradiated to 9 dpa (displacements per atom) at ≈1440 °C, began transforming to α-SiC, with radiation-induced Frank dislocation loops serving as the apparent nucleation sites. 1440 °C is a far lower temperature than usual β → α phase transformations in SiC. SiC is considered for applications in advanced nuclear systems, as well as for electronic or spintronic applications requiring ion irradiation processing. β-SiC, preferred for nuclear applications, is metastable and undergoes a phase transformation at high temperatures (typically 2000 °C and above). Nuclear reactor concepts are not expected to reach the very high temperatures for thermal transformation. However, our results indicate incipient β → α phase transformation, in the form of small (~5–10 nm) pockets of α-SiC forming in the β matrix. In service transformation could degrade structural stability and fuel integrity for SiC-based materials operated in this regime. However, engineering this transformation deliberately using ion irradiation could enable new electronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Local chemical fluctuation mediated ultra-sluggish martensitic transformation in high-entropy intermetallics

Superelasticity associated with martensitic transformation has found a broad range of engineering applications, such as in low-temperature devices in the aerospace industry. Nevertheless, the narrow working temperature range and strong temperature sensitivity of the first-order phase transformation significantly hinder the usage of smart metallic components in many critical areas. Here, we scrutinized the phase transformation behavior and mechanical properties of multicomponent B2-structured intermetallic compounds. Strikingly, the (TiZrHfCuNi) 83.3 Co 16.7 high-entropy intermetallics (HEIs) show superelasticity with high critical stress over 500 MPa, high fracture strength of over 2700 MPa, and small temperature sensitivity in a wide range of temperatures over 220 K. The complex sublattice occupation in these HEIs facilitates formation of nano-scaled local chemical fluctuation and then elastic confinement, which leads to an ultra-sluggish martensitic transformation. The thermal activation of the martensitic transformation was fully suppressed while the stress activation is severely retarded with an enhanced threshold stress over a wide temperature range. Moreover, the high configurational entropy also results in a small entropy change during phase transformation, consequently giving rise to the low temperature sensitivity of the superelasticity stress. Furthermore, our findings may provide a new paradigm for the development of advanced superelastic alloys, and shed new insights into understanding of martensitic transformation in general.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Heating-induced glass-glass and glass-liquid transformations in computer simulations of water

Water exists in at least two families of glassy states, broadly categorized as the low-density (LDA) and high-density amorphous ice (HDA). Remarkably, LDA and HDA can be reversibly interconverted via appropriate thermodynamic paths, such as isothermal compression and isobaric heating, exhibiting first-order-like phase transitions. We perform out-of-equilibrium molecular dynamics simulations of glassy water using the ST2 model to study the evolution of LDA and HDA upon isobaric heating. Depending on pressure, glass-to-glass, glass-to-crystal, glass-to-vapor, as well as glass-to-liquid transformations are found. Specifically, heating LDA results in the following transformations, with increasing heating pressures: (i) LDA-to-vapor (sublimation), (ii) LDA-to-liquid (glass transition), (iii) LDA-to-HDA-to-liquid, (iv) LDA-to-HDA-to-liquid-to-crystal, and (v) LDA-to-HDA-to-crystal. Similarly, heating HDA results in the following transformations, with decreasing heating pressures: (a) HDA-to-crystal, (b) HDA-to-liquid-to-crystal, (c) HDA-to-liquid (glass transition), (d) HDA-to-LDA-to-liquid, and (e) HDA-to-LDA-to-vapor. A more complex sequence may be possible using lower heating rates. For each of these transformations, we determine the corresponding transformation temperature as function of pressure, and provide a P-T “phase diagram” for glassy water based on isobaric heating. Our results for isobaric heating dovetail with the LDA-HDA transformations reported for ST2 glassy water based on isothermal compression/decompression processes [Chiu et al., J. Chem. Phys. 139, 184504 (2013)]. The resulting phase diagram is consistent with the liquid-liquid phase transition hypothesis. At the same time, the glass phase diagram is sensitive to sample preparation, such as heating or compression rates. Interestingly, at least for the rates explored, our results suggest that the LDA-to-liquid (HDA-to-liquid) and LDA-to-HDA (HDA-to-LDA) transformation lines on heating are related, both being associated with the limit of kinetic stability of LDA (HDA)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

An integral transform technique for kinetic systems with collisions

The linearized Vlasov-Poisson system can be exactly solved using the G-transform, an integral transform introduced in Morrison and Pfirsch [Phys. Fluids B 4, 3038–3057 (1992)] and Morrison [Phys. Plasmas 1, 1447 (1994); Transp. Theory Stat. Phys. 29, 397 (2000)] that removes the electric field term, leaving a simple advection equation. We investigate how this integral transform interacts with the Fokker-Planck collision operator. The commutator of this collision operator with the G-transform (the “shielding term”) is shown to be negligible. We exactly solve the advection-diffusion equation without the shielding term. This solution determines when collisions dominate and when advection (i.e., Landau damping) dominates. This integral transform can also be used to simplify gyro-/drift-kinetic equations. We present new gyrofluid equations formed by taking moments of the G-transformed equation. Since many gyro-/drift-kinetic codes use Hermite polynomials as base elements, we include an explicit calculation of their G-transform

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

No evidence for transient transformation via pollen magnetofection in several monocot species

The development of rapid and efficient transformation methods for many plant species remains an obstacle in both the basic and applied plant sciences. A novel method described by Zhao et al. (2017) used magnetic nanoparticles to deliver DNA into pollen grains of several dicot species, and one monocot (lily), to achieve transformation (“pollen magnetofection”). Using the published protocol, extensive trials by two independent research groups showed no indication of transient transformation success with pollen from two monocots, maize and sorghum. To further address the feasibility of magnetofection, lily pollen was used for side-by-side trials of magnetofection with a proven methodology for transient transformation, biolistics. Using a Green Fluorescent Protein reporter plasmid, transformation efficiency with the biolistic approach averaged 0.7% over three trials. However, the same plasmid produced no recognizable transformants via magnetofection, despite screening >3500 individual pollen grains. We conclude that pollen magnetofection is not effective for transient transformation of pollen for at least three species of monocots, and suggest that efforts to replicate the magnetofection protocol in dicot species would be useful to fully assess its potential. ARISING FROM Zhao et al. Nature Plants https://doi.org/10.1038/s41477-017-0063-z (2017)

Vejlupkova, Zuzana↗
DOE OSTI2020

Theory of finite-temperature two-dimensional structural transformations in group-IV monochalcogenide monolayers

An account of two-dimensional (2D) structural transformations in 2D ferroelectrics predicts an evolution from a structure with Pnm 2 1 symmetry into a structure with square P4/nmm symmetry and is consistent with experimental evidence, while another argues for a transformation into a structure with rectangular Pnmm symmetry. An analysis of the assumptions made in these models is provided here, and six fundamental results concerning these transformations are contributed as follows: (i) Softened phonon modes produce rotational modes in these materials. (ii) The transformation to a structure with P4/nmm symmetry occurs at the lowest critical temperature T c . (iii) The hypothesis that one unidirectional optical vibrational mode underpins the 2D transformation is unwarranted. (iv) Being successively more constrained, a succession of critical temperatures ( T c < T c ' < T c " ) occurs in going from molecular dynamics calculations with the NPT and NVT ensembles onto models with unidirectional oscillations. (v) The choice of exchange-correlation functional impacts the estimate of the critical temperature. (vi) Importantly, the correct physical picture of these transformations is one in which rotational modes confer a topological character to the 2D transformation via the proliferation of vortices.

2d ferroelectrics↗
DOE OSTI2018

Role of Reversible Phase Transformation for Strong Piezoelectric Performance at the Morphotropic Phase Boundary

A functional material with coexisting energetically equivalent phases often exhibits extraordinary properties such as piezoelectricity, ferromagnetism, and ferroelasticity, which is simultaneously accompanied by field-driven reversible phase transformation. The study on the interplay between such phase transformation and the performance is of great importance. Here, we have experimentally revealed the important role of field-driven reversible phase transformation in achieving enhanced electromechanical properties using in situ high-energy synchrotron x-ray diffraction combined with 2D geometry scattering technology, which can establish a comprehensive picture of piezoelectric-related microstructural evolution. High-throughput experiments on various Pb/Bi-based perovskite piezoelectric systems suggest that reversible phase transformation can be triggered by an electric field at the morphotropic phase boundary and the piezoelectric performance is highly related to the tendency of electric-field-driven phase transformation. A strong tendency of phase transformation driven by an electric field generates peak piezoelectric response. Further, phase-field modeling reveals that the polarization alignment and the piezoelectric response can be much enhanced by the electric-field-driven phase transformation. In conclusion, the proposed mechanism will be helpful to design and optimize the new piezoelectrics, ferromagnetics, or other related functional materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigation of Various Transformer Topologies for HF Isolation Applications

High-frequency (HF) transformers are an essential part of many power electronic devices. The performance and behavior of HF transformers can greatly affect the efficiency and performance of all systems, particularly, from a parasitic parameter point of view. In this article, HF transformers' parasitic parameters, such as leakage inductances and parasitic capacitances, are analyzed using a novel analytical method, finite element method (FEM), and experimental measurements of different structures and winding arrangements. Also, the magnetic field, electric field, electric displacement field, and electric potential distribution within the transformers are simulated and analyzed. Four different HF transformers with E and U cores with different windings are designed and analyzed. Investigation outcomes help to classify structures according to the trade-off between leakage inductances and series parasitic capacitances. This information can later be used for the optimal selection and design of transformers as a function of their operating frequency for any power rating and voltage level. Moreover, 3-D FEM and experimental results validate the proposed methodology to be used for designing HF transformers in high-voltage/power applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Type IV-like pili facilitate transformation in naturally competent archaea

Naturally competent organisms are capable of DNA uptake directly from the environment through the process of transformation. Despite the importance of transformation to microbial evolution, DNA uptake remains poorly characterized outside the bacterial domain. Here, we identify the pilus as a necessary component of the transformation machinery in archaea. We describe two naturally competent organisms: Methanococcus maripaludis and Methanoculleus thermophilus. In M. maripaludis, replicative vectors were transferred with an average efficiency of 2.4 x 10 3 transformants μg -1 DNA. In M. thermophilus, integrative vectors were transferred with an average efficiency of 2.7 x 10 3 transformants μg -1 DNA. Additionally, natural transformation of M. thermophilus could be used to introduce chromosomal mutations. To our knowledge, this is the first demonstration of a method to introduce targeted mutations in a member of the order Methanomicrobiales. For both organisms, mutants lacking structural components of the type IV-like pilus filament were defective for DNA uptake, demonstrating the importance of pili for natural transformation. Interestingly, competence could be induced in a non-competent strain of M. maripaludis by expressing pilin genes from a replicative vector. Furthermore, these results expand the known natural competence pili to include examples from the archaeal domain and highlight the importance of pili for DNA uptake in diverse microbial organisms.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Analysis and Planning Framework for Nuclear Plant Transformation

Commercial nuclear power in the United States has been an unqualified success by any measure, providing low cost, carbon-free, and safe baseload electricity for decades. The industry today is at the peak of its historical performance in terms of generation output, reliable operations, and demonstrated nuclear safety. However, it is no longer among the lowest-cost electric generation sources with the emergence of subsidized renewables and shale gas generation. The business model that has served the operating nuclear fleet so well over its life is now a drag on cost performance due to its reliance on a large highly skilled labor force. In contrast, digital technology and innovation are enabling dramatic efficiencies in energy production, resulting in fierce competition for a commodity such as electricity. The nuclear power industry has responded to this challenge with many initiatives to improve efficiency and modernize plant equipment, especially where reliability and obsolescence issues are pressing. However, it would be a missed opportunity to merely modernize the plant components and the work processes of an outdated business model that was formulated to manage the technology of the 1960s. Rather, the greater opportunity is to transform that business model to one that fully exploits the capabilities of modern digital technology, resulting in substantially lower production costs and sustainable market viability. One successful example of such transformation is the concept of Integrated Operations, which was introduced into the North Sea oil and gas industry a couple of decades ago when the profitability of operating these fields was severely threatened by low world petroleum prices and the high overhead of operating the offshore oil and gas platforms. This effort resulted in significant changes to how these oil fields were operated and allowed the industry to continue profitable operation of these platforms. This example has some remarkable parallels to the U.S. commercial nuclear industry as described in the next section. This report provides an analysis and planning framework for such a nuclear plant operating model transformation based on the transferable learnings from the North Sea transformation. This framework is termed Integrated Operations for Nuclear or ION. This report describes the key principles and methods of Integrated Operations and how they are being applied in a collaboration between the DOE Light Water Reactor Sustainability Program and Xcel Energy in an initiative to transform its operating model for performance improvement and long-term sustainability. It describes a method to bring the operating costs of a nuclear fleet in line with market-based pricing, transforming work functions to reduce cost with technology innovations. This initiative will continue over the next several years in the detailed development of transformative concepts for nuclear plants, which will be published as follow-up to this initial report on Integrated Operations for Nuclear.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

EMP-Resilient Electric Grid Transformer Analysis

The response of a high - voltage (HV) transformer to fast rise time voltages, such as that from a electromagnetic pulse (EMP) can result in interruption of power distribution and possibly system failure. To help identify these potential occurrences, it is necessary to develop a transformer model that not only captures the input/output response of the transformer but also the internal behavior. The model constructed should cover the frequency band of interest while capturing the internal physical and electrical characteristics. This broad-band, high-fidelity model would enable the prediction of unwanted effects through simulation. A proposed modeling scheme for a HV transformer is described in Part 1 of this report. Part 2 of this report details assessments of internal voltage and electrical field holdoff testing of transformer insulation dielectric breakdown, including comparison of low frequency (DC/60 Hz) holdoff to rise times characteristic of lightning (1 s) and EMP E1 transients (10 - 30 ns). This initial project is a path toward establishing electrical grid transformer failure criteria for EMP voltage transients. We developed modeling methods and measured breakdown electrical field statistical distributions for direct current, 60 Hz, lightning and EMP characteristic voltage rise times. Methods of nanosecond-scale capacitive discharge unit high voltage source development, suggestions for derating of 60 Hz insulation maximum electrical fields for EMP nanosecond pulse voltage withstand rating, and potential methods for increasing transformer resilience to such fast rise time pulses are described.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Grid-Connected Modular Soft-Switching Solid State Transformers (M-S4T)

The objective of this project is to develop and verify the concept of a flexible and modular soft-switching solid-state transformer (M-S4T) for direct grid-connected applications. The ability to directly connect power electronics converters to the medium voltage grid (4 kV – 13 kV), and to potentially replace the passive and bulky, but ubiquitous 60 hertz service transformer in the 25 kVA to 100 kVA range, with a more flexible and controllable device, has been regarded as the ‘holy grail’ in grid control. However, this has proven to be extremely difficult. This project has developed the solutions to several key challenges of the direct grid-connected power electronics and realized a 7.2 kV M-S4T prototype. First, a protection method to protect the M-S4T from the high voltages (110 kV for the 13 kV system) that occur on the grid due to transients and lightning strikes have been developed and experimentally verified. Second, the realization and the operation of the M-S4T based on high-voltage SiC devices (>3.3 kV) and a medium-frequency medium-voltage low-leakage transformer in a single-stage solid-state transformer with zero-voltage switching, low dv/dt, and low electromagnetic interference has been successfully demonstrated up to 7.5 kV peak. Third, an oil-cooling system and stable communication and distributed control system for converter module voltage sharing have been developed and experimentally verified. The developed M-S4T has realized a modular universal high-performance power conversion system. This conversion system is scalable to different voltage and power levels and adaptable to four-quadrant bidirectional operation. Moreover, the use of passive cooling techniques meets the equipment life requirements, and the lightning protection scheme fulfills the basic insulation level specifications for direct grid connection. Such power conversion system opens up near-term opportunities, including energy storage, solar PV, or electric vehicle charging with significant cost and footprint savings. In the longer term, the possibility of replacing the utility distribution transformer with an M-S4T will be transformative for future distribution grids with a compact footprint and full controllability to enable high renewable energy and storage penetration. In addition to the main project, this report expands on the Plus-Up projected including as part of the main award. This project developed and demonstrated the technology for autonomous collaborative inverters that can be connected in an ad hoc manner to the grid. The aim of the project was to: (1) evaluate the existing techniques for grid-connected inverters and find their limitations; (2) develop detailed requirements for grid-connected inverters in the modern grid with millions of active nodes; (3) design a unified control strategy that brings more autonomy and intelligence to grid-connected inverters, and addresses parts of the issues with the existing techniques. The proposed technique, called UniCon, enables inverters to 1) connect/disconnect to/from the grid in an ad hoc manner; (2) work based on local sensing. Slow communication could be used for a more optimized behavior; (3) work automatically in both grid-forming/grid-following mode; (4) handle large disturbances, e.g., big load step and fault, in an oscillation-free manner; (5) work collaboratively with other inverters in steady-state and during transients. UniCon can be implemented in the middle-level control; hence it is agnostic to the vendor and to the implementation of the inner voltage/current and protection loops. Furthermore, a new synchronization scheme, based on deep learning, was developed that can extract the grid voltage phase and amplitude in a stable manner. The method is cheap to implement can improve the dynamic performance of the grid-connected inverters during fast transients, e.g., fault. The proposed control scheme was validated by (1) MATLAB/Simulink; (2) hardware-in-the-loop results, and; (3) experimental results using three inverters that form a microgrid in a down-scaled feeder. Lastly, both the M-S4T and UniCon have achieved promising tangible paths to markets. In the case of the M-S4T, the underlying technology — the Soft Switching Solid State Transformer (S4T) developed at the Georgia Tech Center for Distributed Energy (GT-CDE) has been licensed by GridBlock from the Georgia Tech Research Corporation, and GridBlock has been working with manufacturing partner Jabil (one of the largest US-based contract manufacturers) and system integrator Power Secure (largest deployer of microgrids in the US with 4.7 GW under management), to meet the strong initial demand. Similarly, GridBlock has an exclusive license to the UniCon technology, developed under this award by GT-CDE. The UniCon provides an intermediate control layer that enables the implementation of the higher-level ‘transactive’ control commands for the system. The architecture of the system - slow communications with the cloud for system optimization and setpoints, and the use of locally measured quantities for real-time control, provide a very robust and secure way of implementing a real-time must-run grid that is also secure and stable. This is a brand-new functionality that is critical for the future grid and key to GridBlock’s business model.

24 POWER TRANSMISSION AND DISTRIBUTION↗