Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thrust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Advanced Modeling of Control-Structure Interaction in Thrust Vector Control Systems

The Space Launch System (SLS) Core Stage (CS) Thrust Vector Control (TVC) system is comprised of 8 mechanical feedback Shuttle heritage Type III TVC actuators and four RS-25 engines, each attached to a Shuttle heritage gimbal block/bearing. Two actuators are used to move each engine in two planes perpendicular to one another (i.e., pitch and yaw). The TVC system design leverages hardware from the Space Shuttle program as well as new hardware designed specifically for the Core Stage. During the development of the SLS TVC system, a family of advanced dynamics models were developed to extend and compliment the simplified quasi-linear “simplex” model historically used for flight control design and stability analysis. The importance of these advanced models became increasingly evident after ambient and hot fire testing of the Core Stage, which revealed a number of findings associated with the dynamic response of the TVC integrated system. Test responses suggested that the TVC did not meet its performance specifications and its step and frequency responses exhibited unexpected departures from prior lab tests and modeled behavior. One driving factor for these results was a higher-than-expected degree of coupling between the TVC system, the engine dynamics, and the Core Stage structure. This paper is the third installment in a seven-paper series surveying the design, engineering, test validation, and flight performance of the Core Stage Thrust Vector Control system. In this paper, a new method of modeling rocket vehicle thrust vectoring servoelastic dynamics is presented. In this approach, the load dynamics are replaced by a detailed finite element model containing both the rigid body and elastic modes. A partitioning technique is used to compute the effective compliance from the modal data and obtain accurate simulation results using a reduced number of generalized coordinates. Coupled backup structure and nozzle attach compliance effects on multiple engines are captured in higher fidelity than with a spring approximation, eliciting novel effects due to the complex load paths involved in the Core Stage structure. Validation of the model is demonstrated using a variety of structural/modal, laboratory, and full-scale hot fire test data.

Launch Vehicles↗

Advanced Modeling of Control-Structure Interaction in Thrust Vector Control Systems

The Space Launch System (SLS) Core Stage (CS) Thrust Vector Control (TVC) system is comprised of 8 mechanical feedback Shuttle heritage Type III TVC actuators and four RS-25 engines, each attached to a Shuttle heritage gimbal block/bearing. Two actuators are used to move each engine in two planes perpendicular to one another (i.e., pitch and yaw). The TVC system design leverages hardware from the Space Shuttle program as well as new hardware designed specifically for the Core Stage. During the development of the SLS TVC system, a family of advanced dynamics models were developed to extend and compliment the simplified quasi-linear “simplex” model historically used for flight control design and stability analysis. The importance of these advanced models became increasingly evident after ambient and hot fire testing of the Core Stage, which revealed a number of findings associated with the dynamic response of the TVC integrated system. Test responses suggested that the TVC did not meet its performance specifications and its step and frequency responses exhibited unexpected departures from prior lab tests and modeled behavior. One driving factor for these results was a higher-than-expected degree of coupling between the TVC system, the engine dynamics, and the Core Stage structure. This paper is the third installment in a seven-paper series surveying the design, engineering, test validation, and flight performance of the Core Stage Thrust Vector Control system. In this paper, a new method of modeling rocket vehicle thrust vectoring servoelastic dynamics is presented. In this approach, the load dynamics are replaced by a detailed finite element model containing both the rigid body and elastic modes. A partitioning technique is used to compute the effective compliance from the modal data and obtain accurate simulation results using a reduced number of generalized coordinates. Coupled backup structure and nozzle attach compliance effects on multiple engines are captured in higher fidelity than with a spring approximation, eliciting novel effects due to the complex load paths involved in the Core Stage structure. Validation of the model is demonstrated using a variety of structural/modal, laboratory, and full-scale hot fire test data.

Launch Vehicles↗

Flow, Noise and Thrust of Supersonic Plug Nozzles

A model-scale experimental study is conducted with a plug nozzle exploring the performance of various plug geometries for supersonic aircraft concepts. All data are acquired with a given outer nozzle that is convergent and has an exit diameter of 2 inches. The shape of the centrally placed plug is varied from conic with various half-angles (lengths), to method of characteristics (MoC) designs, as well as truncated and porous geometries. Noise and schlieren flow visualization data, presented in an earlier paper, are briefly reviewed first. The focus in this paper is on the thrust performance. A newly constructed thrust stand is used to acquire data covering a nozzle pressure ratio (NPR) range from transonic (‘landing and takeoff’, LTO) to supersonic (‘cruise’) conditions. Back-to-back measurements allowed assessment of relative performance. A plug with its ‘crown’ located somewhat inside the nozzle, rather than near the exit, is found to perform better. A longer 10° plug performs better than a shorter 22° plug. A porous plug, that significantly suppresses broadband shock associated noise, is found to incur a modest thrust loss that might be an acceptable tradeoff near LTO conditions. A companion numerical simulation for some of the plug geometries yields data trends bearing reasonable agreement with the experimental results.

jets↗

Recovery from Missed Thrust During Gateway's NRHO Insertion Using Auxiliary Propulsion

Various strategies are assessed by which the first two elements of Gateway could recover from missed thrust events during insertion into a Near Rectilinear Halo Orbit (NRHO). Recovery strategies are assessed in terms of their ability to maintain the desired NRHO insertion epoch ad well as their cost in terms of additional time and ∆v required to reach the NRHO. Strategies utilize a 50 kW Solar Electric Propulsion (SEP) system onboard the Power and Propulsion Element (PPE). Recovery solutions are found that, in the event of a missed thrust arc during the Insertion Phase of the Gateway Lunar Transit, deliver the space-craft into the NRHO within three additional revolutions (roughly 21 days) and 80 m/s ∆v.

missed thrust↗

Implications for elastic energy storage in the Himalaya from the Gorkha 2015 earthquake and other incomplete ruptures of the Main Himalayan Thrust

Rupture in the 2015 M7.8 Gorkha earthquake nucleated at the downdip edge of the Main Himalayan Thrust (MHT) near the transition from interseismic locking to aseismic creep beneath the Tibetan plateau, and propagated incompletely towards the Main Frontal Thrusts (MFT). Despite the imposition of a substantial static strain in the mid-décollement, afterslip on the MHT within a year of the earthquake had decayed to negligible levels. Earthquakes that incompletely rupture the MHT (7 < Mw < 7.9) have been relatively common in the past two centuries, and as a consequence heterogeneous patches of stored elastic strain must exist throughout the Himalaya similar to that emplaced by the Gorkha earthquake. We show that these patches of stored strain are not dissipated by creep or by subsequent updip earthquakes, with the possible exceptions of a sequence of moderate earthquakes to the west of the great 1950 Assam earthquake, and to the east of the Kangra 1905 earthquake. It is thus considered likely that mid-décollement strain newly imposed by the Gorkha earthquake, and other recent incomplete ruptures will be incorporated in the rupture of a future much larger earthquake. Incomplete ruptures (i.e. those that nucleate downdip but fail to rupture the frontal thrusts) appear to occur preferentially in parts of the central Himalaya characterized by relatively narrow transition regions of interseismic decoupling (<30 km downdip). Assuming uniform strain at failure these narrow zones are unable to store large amounts of strain energy compared to wide zones of interseismic decoupling. Since the transition from fully locked to a fully creeping rheology depends partly on temperature, to first order the width of the interseismic decoupling transition zone depends on the local dip of the MHT. Where the decoupling zone is narrow (25 km) moderate earthquakes (6 < Mw < 7) are observed to occur at intervals of a few hundred years. Where the transition zone is wide (e.g. Kashmir and Assam, 150 km) great earthquakes nucleate at long time intervals (millennia). Because the cumulative moment release of moderate earthquakes in regions of narrow seismic decoupling is insufficient to keep up with plate convergence, we conclude that megaquakes that eventually sweep through these regions are augmented by the heterogenous fossil strain of former incomplete ruptures. Because great earthquakes in the central Himalaya are inferred to nucleate from moderate earthquakes near the base of the MHT, the preparation zones of these moderate earthquakes may provide opportunities for forecasting the approach of future great earthquakes.

58 GEOSCIENCES↗

Pulsed thrust measurements using electromagnetic calibration techniques

A thrust stand for accurately measuring impulse bits, which ranged from 10-1000 {mu}N s using a noncontact electromagnetic calibration technique is described. In particular, a permanent magnet structure was designed to produce a uniform magnetic field, and a multiturn coil was made to produce a calibration force less than 10 mN. The electromagnetic calibration force for pulsed thrust measurements was linear to the coil current and changed less than 2.5% when the distance between the coil and magnet changed 6 mm. A pulsed plasma thruster was first tested on the thrust stand, and afterward five single impulse bits were measured to give a 310 {mu}N s average impulse bit. Uncertainty of the measured impulse bit was analyzed to evaluate the quality of the measurement and was found to be 10 {mu}N s with 95% credibility.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thrust measurements of a hollow-cathode discharge

Thrust measurements of a hollow cathode mercury discharge were made with a synthetic mica target on a torsion pendulum. Thrust measurements were made for various target angles, tip temperatures, flow rates, keeper discharge powers, and accelerator electrode voltages. The experimental thrust data are compared with theoretical values for the case where no discharge power was employed.

Snyder, A.↗

Analysis of oil lubricated, fluid film, thrust bearings with allowance for temperature dependent viscosity

A preliminary design study was performed to seek a fluid-film thrust bearing design intended to be part of a high-speed, hybrid (rolling element/fluid film) bearing configuration. The base line used is a design previously tested. To improve the accuracy of theoretical predictions of load capacity, flow rate, and friction power loss, an analytical procedure was developed to include curvature effects inherent in thrust bearings and to allow for the temperature rise in the fluid due to viscous heating. Also, a narrow-groove approximation in the treatment of the temperature field was formulated to apply the procedure to the Whipple thrust bearing. A comparative trade-off study was carried out assuming isothermal films; its results showed the shrouded-step design to be superior to the Whipple design for the intended application. An extensive parametric study was performed, employing isoviscous calculations, to determine the optimized design, which was subsequently recalculated allowing for temperature effects.

Pan, C. H. T.↗

Basic parameters for low thrust mission and system analysis.

Development of a basic set of normalized parameters to represent low-thrust system characteristics. The conditions which must be met to obtain trajectory and performance data which are invariant with the launch vehicle characteristics, the selected power, the specific mass of the low-thrust vehicle, and the efficiency of the ion propulsion system are derived. This normalized representation of mission characteristics frees the analyst from having to rerun the trajectories if any of the aforementioned parameters are varied. Examples pertaining to a low-thrust Jupiter flyby and comet Encke rendezvous are given to demonstrate the utility of the method of presentation.

Barber, T. A.↗

Thrust vectoring systems

The design, fabrication, and testing of thrust vectorable ion optical systems capable of controlling the thrust direction from both 5- and 30-cm diameter ion thrusters is described. Both systems are capable of greater than 10 deg thrust deflection in any azimuthal direction. The 5-cm system is electrostatic and hence has a short response time and minimal power consumption. It has recently been tested for more than 7500 hours on an operational thruster. The 30-cm system is mechanical, has a response time of the order of 1 min, and consumes less than 0.3% of the total system input power at full deflection angle.

King, H. J.↗

SSME structural computer program development. Volume 3: BOPACE demonstration analysis of the SSME thrust chamber liner

The application of a structural computer program for analysis of a thrust chamber liner is discussed. Two objectives were accomplished as follows: (1) exercise of the full capabilities of the computer program and (2) definition of thermal and mechanical boundary conditions to reflect the emergency power level operating conditions for the SSME 47OK engine at a station just upstream of the thrust chamber throat. Creep information on the thrust chamber is presented as a reference curve of creep strain versus time for various temperatures. Contour plots of the effective plastic strain, effective stress, and effective creep strain are developed.

Spring, A. H.↗

Low thrust space vehicle trajectory optimization using regularized variables

Optimizing the trajectory of a low thrust space vehicle usually means solving a nonlinear two point boundary value problem. In general, accuracy requirements necessitate extensive computation times. In celestial mechanics, regularizing transformations of the equations of motion are used to eliminate computational and analytical problems that occur during close approaches to gravitational force centers. It was shown in previous investigations that regularization in the formulation of the trajectory optimization problem may reduce the computation time. In this study, a set of regularized equations describing the optimal trajectory of a continuously thrusting space vehicle is derived. The computational characteristics of the set are investigated and compared to the classical Newtonian unregularized set of equations. The comparison is made for low thrust, minimum time, escape trajectories and numerical calculations of Keplerian orbits. The comparison indicates that in the cases investigated for bad initial guesses of the known boundary values a remarkable reduction in the computation time was achieved. Furthermore, the investigated set of regularized equations shows high numerical stability even for long duration flights and is less sensitive to errors in the guesses of the unknown boundary values.

Schwenzfeger, K. J.↗

Evaluation of chromium oxide and molybdenum disulfide coatings in self-acting stops of an air-lubricated Rayleigh step thrust bearing

Two coatings for a Rayleigh step thrust bearing were tested when coasting down and stopping under self-acting operation in air. The thrust bearing had an outside diameter of 8.9 cm (3.5 in.), an inside diameter of 5.4 cm (2.1 in.), and nine sectors. The load was 73 N (16.4 lbf). The load pressure was 19.1 kN/per square meter (2.77 lbf/per square inch) on the total thrust bearing area. The chromium oxide coating was good to 150 stops without bearing deterioration, and the molybdenum disulfide coating was good for only four stops before bearing deterioration. The molybdenum disulfide coated bearing failed after nine stops.

Nemeth, Z. N.↗

The results of a low-speed wind tunnel test to investigate the effects of the Refan JT8D engine target thrust reverser on the stability and control characteristics of the Boeing 727-200 airplane

The effects of the Refan JT8D side engine target thrust reverser on the stability and control characteristics of the Boeing 727-200 airplane were investigated using the Boeing-Vertol 20 x 20 ft Low-Speed Wind Tunnel. A powered model of the 727-200 was tested in groud effect in the landing configuration. The Refan target reverser configuration was evaluated relative to the basic production 727 airplane with its clamshell-deflector door thrust reverser design. The Refan configuration had slightly improved directional control characteristics relative to the basic airplane. Clocking the Refan thrust reversers 20 degrees outboard to direct the reverser flow away from the vertical tail, had little effect on directional control. However, clocking them 20 degrees inboard resulted in a complete loss of rudder effectiveness for speeds greater than 90 knots. Variations in Refan reverser lip/fence geometry had a minor effect on directional control.

Kupcis, E. A.↗

Performance of a model cascade thrust reverser for short-haul applications

Aerodynamic and acoustic characteristics are presented for a cowlmounted, model cascade thrust reverser suitable for short-haul aircraft. Thrust reverser efficiency and the influence on fan performance were determined from isolated fan-driven models under static and forward velocity conditions. Cascade reverser noise characteristics were determined statically in an isolated pipe-flow test, while aerodynamic installation effects were determined with a wind-tunnel, fan-powered airplane model. Application of test results to short-haul aircraft calculations demonstrated that such a cascade thrust reverser may be able to meet both the performance and noise requirements for short-haul aircraft operation. However, aircraft installation effects can be quite significant.

Dietrich, D. A.↗

Simulation of low thrust guidance problems

The determination of optimal rocket control profiles and the guidance procedures used to approximate these profiles have received much attention. Simple guidance procedures have sufficed for the Apollo flights. A modified version of the linear tangent guidance law is developed which can be used for a low-thrust orbital maneuvering system such as the space shuttle. The modification allows the estimation of gravity over long thrusting arcs which is necessary for low thrust systems.

Dawkins, G. S.↗

Optimal rocket thrust profile shaping using third degree spline function interpolation

Optimal solid-rocket thrust profiles for the parallel-burn, solid-rocket-assisted space shuttle are investigated. Solid-rocket thrust profiles are simulated by using third-degree spline functions, with the values of the thrust ordinates defined as parameters. The profiles are optimized parametrically, using the Davidon-Fletcher-Powell penalty function method, by minimizing propellant weight subject to state and control inequality constraints and to terminal boundary conditions. This study shows that optimizing a control variable parametrically by using third-degree spline function interpolation allows the control to be shaped so that inequality constraints are strictly adhered to and all corners are eliminated. The absence of corners, which is realistic in nature, makes this method attractive from the viewpoint of solid rocket grain design.

Johnson, I. L.↗

Space shuttle orbit maneuvering engine reusable thrust chamber program

Tests were conducted on the regenerative cooled thrust chamber of the space shuttle orbit maneuvering engine. The conditions for the tests and the durations obtained are presented. The tests demonstrated thrust chamber operation over the nominal ranges of chamber pressure mixture ratio. Variations in auxiliary film coolant flowrate were also demonstrated. High pressure tests were conducted to demonstrate the thrust chamber operation at conditions approaching the design chamber pressure for the derivative space tug application.

Pauckert, R. P.↗