Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Spinel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Zero-strain high entropy spinel oxide (FeNiCuCrMn) 3 O 4 @rGO as high-performance anode for sodium ion battery

High entropy spinel oxides (HEOs), as a new type of anode material with at least five transition metal elements and high theoretical specific capacity, have enormous promise in sodium ion batteries (SIBs). However, the influence of different transition metal elements on the structure and electrochemical performances of HEOs is not clear. Here, in this study, the addition of Mn to HEO can increase the surface oxygen vacancy (O v ) concentration, shorten the band gap, and enhance the electrochemical performance of (FeNiCuCrMn) 3 O 4 @rGO. XPS results show (FeNiCuCrMn)3O4@rGO has the highest surface O v concentration. Ab initio calculations demonstrate that the indirect band gap of (FeNiCuCrMn)3O4@rGO is 0.068 eV. In situ X-ray diffraction and synchrotron X-ray absorption spectroscopy reveal that (FeNiCuCrMn) 3 O 4 @rGO exhibits a zero-strain characteristic with an inconsequential unit cell volume change of 0.2 %. Specifically, (FeNiCuCrMn) 3 O 4 @rGO as anode materials for SIBs show good cyclic stability (with a capacity retention of 84 % at 500 mA g −1 after 3000 cycles). Overall, this work provides a new direction for optimizing transition metal elements in HEOs.

36 MATERIALS SCIENCE↗

Toward a tunable fabrication of multifunctional iron-aluminum spinels via solution combustion synthesis: The effects of fuel, heating mode, and Fe:Al precursor ratio

The solid solutions of iron and aluminum spinels (hercynite, maghemite, magnetite, and γ-alumina) are promising materials for emerging technologies such as solar thermochemical fuel production and clean dehydrogenation of fossil fuels. Solution combustion synthesis (SCS) is an attractive technique for the fabrication of these materials as it has been used for synthesis of many nanoscale oxides. However, the design space of SCS is large with many synthesis parameters affecting the properties of the combustion products. To optimize the SCS of these materials, it is important to determine which parameters yield the best properties. In the present work, FeAlO x nanocomposites were obtained by SCS using iron nitrate and aluminum nitrate as precursors and oxidizers. Two fuels (citric acid and glycine), three Fe:Al molar ratios (1:2, 1:1, and 2:1) in the precursors, and three heating modes (hotplate, muffle furnace, and microwave oven) were compared. The products were characterized by X-ray diffraction analysis, scanning electron microscopy, Brunauer-Emmett-Teller surface area analysis, and laser diffraction particle size analysis. The fuel used had the largest impact on the combustion behavior and hence the material properties. The high combustion temperature of glycine allowed for the formation of an FeAl 2 O 4 /Fe 3 O 4 solid solution, while the lower-temperature combustion of citric acid yielded Al-substituted γ-Fe 2 O 3 with high amorphous content. With citric acid, the specific surface area as high as 200 m 2 /g was achieved. The effect of Fe:Al precursor ratio was clearly seen in variations of the lattice parameter, which demonstrated the ability to tune the phase composition. The heating mode had minor effects on material properties, but some differences were observed. As a result, all products obtained by SCS in a microwave oven had low specific surface areas compared to those obtained with a hotplate and a muffle furnace.

Alumina↗

Conductive spinels derived from Co–Mn based alloy precursor for SOFC cathode-side contact application

The utilization of gas-atomized Co–Mn based alloy precursor is a promising approach to lowering the sintering temperature of the spinel contact layer and enhancing its performance. In this work, simulated interconnect/contact/cathode cells are employed to investigate the effects of different metallic precursors (i.e., three Co–Mn based alloy powders and a mixture of Co + MnO 2 powders) on the microstructure and performance of the reactively-sintered MnCo 2 O 4 -based contact layer. While excellent overall electrical performance is observed for all the cells with the four contact precursors during 1000-h testing at 800 °C in air, the cell with the Ce-doped alloy contact precursor shows the lowest cell area specific resistance (ASR) and ASR degradation rate. Cross-sectional observation of the tested cells is conducted to assess the compatibility of the contact layer with adjacent components as well as its effectiveness in reducing the Cr 2 O 3 scale growth and blocking Cr migration from the interconnect to the cathode.

08 HYDROGEN↗

Fabrication of epitaxial γ-Al 2 O 3 and spinel NiAl 2 O 4 films on SrTiO 3 by Pulsed Laser Ablation

Spinel -Al2O3 and NiAl2O4 thin films were grown on (001) SrTiO3 substrates by pulsed laser deposition. The high quality of epitaxial growth and cube-on-cube orientation of the films were confirmed by x-ray diffraction and transmission electron microscopy. The growth of NiAl2O4 thin films is related to the reaction between sequentially deposited -Al2O3 and NiO layers. These films were grown using a unique multi-target approach.

36 MATERIALS SCIENCE↗

Enabling high areal capacity for Co-free high voltage spinel materials in next-generation Li-ion batteries

The rapidly growing technological demand for lithium-ion batteries has prompted the development of novel cathode materials with high energy density, low cost, and improved safety. High voltage spinel, LiNi 0.5 Mn 1.5 O 4 (LNMO), is one of the most promising candidates yet to be commercialized. The two primary obstacles for this material are the inferior electronic conductivity and fast capacity degradation in full cells due to the high operating voltage. By systematically addressing these limitations, we successfully develop a thick LNMO electrode with areal capacity loadings up to 3 mAh·cm –2 . The optimized thick electrode is paired with a commercial graphite anode at both the coin cell and pouch cell level, achieving a full cell capacity retention as high as 72% and 78%, respectively, after 300 cycles. We attribute this superior cycling stability to careful optimizations of cell components and testing conditions, with a specific focus improving electronic conductivity and high voltage compatibility. These results suggest precise control of materials quality, electrode architecture and electrolyte optimization can soon support the development of a cobalt-free battery system based on a thick LNMO cathode (>4 mAh·cm 2 ), which will eventually meet the needs of next-generation Li-ion batteries with reduced cost, improved safety, and assured sustainability.

25 ENERGY STORAGE↗

Density functional study on electronic properties of P-doped spinel silicon carbon nitride

We performed density functional calculations on the electronic properties of P-doped spinel silicon carbon nitride. When Si is replaced by C at the tetrahedral sites of P-doped c-Si{sub 3}N{sub 4}, the band gap can be adjusted, and an insulator-to-metal transition is predicted to occur at the C-to-Si ratio of 0.27. Finally, some possible examinations and potential applications for the large band-gap reduction are discussed. - Graphical abstract: We performed density functional calculations to predict the insulator-to-metal transition by replacing Si by C at the tetrahedral sites of P-doped c-Si{sub 3}N{sub 4}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure and electrical properties of single-phase cobalt manganese oxide spinels Mn{sub 3-x}Co{sub x}O{sub 4} sintered classically and by spark plasma sintering (SPS)

Cobalt manganese oxide spinels Mn{sub 3-x}Co{sub x}O{sub 4} (with 0.98{<=}x{<=}3) were prepared by the thermal decomposition in air of oxalate precursors. The influence of the thermal treatments on the structure of these materials is emphasized. Single-phase ceramics were obtained after optimization of the sintering parameters. A precise phase diagram for the Co-Mn-O system is proposed according to thermal stability and structure of oxide powders. The electrical measurements on single-phase ceramics show that low values of resistivity can be achieved. The conduction could take place through jumps of polarons between Mn{sup 3+} and Mn{sup 4+} on octahedral sites. These compounds present interesting electrical characteristics for negative temperature coefficient (NTC) thermistor applications. - Grapical abstract: After elaboration of single-phase and well densified ceramics Mn{sub 3-x}Co{sub x}O{sub 4} (with 0.98{<=}x{<=}3) by conventional and spark plasma sintering, electrical measurements have been taken and low values of resistivity can be achieved. The conductivity shifts from an insulator, Mn{sub 3}O{sub 4} (cationic distribution: Mn{sup 2+}[Mn{sup 3+}]{sub 2}O{sub 4}) to a semiconductor solid solution probably due to the hopping of polarons between Mn{sup 3+} and Mn{sup 4+} on octahedral sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evolution from a ferromagnetic to a spin-glass regime in the spinel-type Cu(Cr{sub 1-x}Ti{sub x}){sub 2}S{sub 4}

Successive changes from ferromagnetic, re-entrant mixed, to spin-glass regime have been manifestly found with increasing Ti-composition x in the quaternary spinel-type Cu(Cr{sub 1-x}Ti{sub x}){sub 2}S{sub 4} system. The Curie temperature T{sub c} decreases steeply with increasing x and this transition becomes ill-defined around x=0.47. Two distinct transitions appear below T{sub c} over the range x=0.40-0.47. Coexistence of the ferromagnetism and spin-glass order would be observed below the Gabay and Toulouse transition (T{sub GT}), owing to freezing of the transverse-spin components without changing of the ferromagnetic order parameter. Finally, at a yet lower temperature de Almeida-Thouless transition (T{sub AT}), the longitudinal-spin component freezes randomly at which an irreversibility arises between zero-field-cooled (ZFC) and field-cooled (FC) magnetizations. Over the range of 0.47{<=}x{<=}0.85, a cusp of the ZFC magnetization is seen at T{sub g} like conventional spin-glass. Specimens with x{>=}0.90 remain paramagnetic down to 2.0 K. A magnetic phase diagram between T versus x has been obtained experimentally. The values of the multicritical point in 100 Oe is detected to be x=0.47 and T=7.40K. The low-field magnetization and the phase diagram are satisfactorily explained by the theory of Gabay and Toulouse on the basis of Heisenberg isotropic vector spin model rather than the Ising spin model. - An enlargement of the magnetic phase diagram for Cu(Cr{sub 1-x}Ti{sub x}){sub 2}S{sub 4} at a constant field of 100 Oe over the range of 0.40{<=}x{<=}0.70. The curves give a guide to the eye: para, paramagnetic; ferro, ferromagnetic; SGI, spin-glass I (GT-phase), and SGII: spin-glass II (AT-phase). Three characteristic temperatures of T{sub c},T{sub GT}, and T{sub AT} merge into 7.40 K at x=0.47 in H=100 Oe. This is a multicritical point.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A fast route to obtain manganese spinel nanoparticles by reduction of K-birnessite

The K-birnessite (K{sub x}MnO{sub 2}.yH{sub 2}O) reduction reaction has been tested in order to obtain manganese spinel nanoparticles. The addition of 0.25 weight percent of hydrazine hydrate, the reducing agent, during 24 hours is efficient to transform the birnessite powder in a hausmanite Mn{sub 3}O{sub 4} powder. Well crystallised square shape nanoparticles are obtained. Different birnessite precursors have been tested and the reaction kinetics is strongly correlated to the crystallinity and granulometry of the precursor. The effects of aging time and hydrazine hydrate amount have been studied. Well crystallised Mn{sub 3}O{sub 4} is obtained in one hour. The presence of feitknechtite (MnO(OH)) and amorphous nanorods has been detected as an intermediate phase during birnessite conversion into hausmanite. The conversion mechanism is discussed. - Graphical abstract: TEM image showing Mn{sub 3}O{sub 4} particle after treatment of birnessite with an addition of hydrazine during 24 hours.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The effects of doping ferromagnetic spinel CdCr{sub 2}Se{sub 4} with Sb{sup 3+} ions

Semiconducting spinel CdCr{sub 2}Se{sub 4} orders ferromagnetically below T{sub C}=130 K. A series of single-crystals of CdCr{sub 2}Se{sub 4} doped with Sb{sup 3+} ions has been synthesized in order to study an effect of the substitution on the cation distribution and the magnetic properties. The compounds of Cd{sub y}Sb{sub x}Cr{sub z}Se{sub 4} have been investigated by means of X-ray diffraction, magnetization measurements and electron spin resonance spectroscopy. Two selected samples of the composition (Cd{sub 1-x}Sb{sub x})[Cr{sub 2}]Se{sub 4} with x=0.13 and 0.44 retained cubic symmetry with space group Fd3-barm. The unit cell parameter appeared to be sensitive to the concentration of Sb{sup 3+} admixture: it increases with x, despite a close similarity in the ionic radii of Cd{sup 2+} and Sb{sup 3+} in tetrahedral coordination. Upon partial substitution of Cd{sup 2+} by Sb{sup 3} no obvious change in the Curie temperature was observed, however, the effective magnetic moment slightly increased, what may result from the appearance of Cr{sup 2+} ions. The characteristic feature of the system studied is an extended range of short-range magnetic order, in which the magnetic properties in the paramagnetic state are governed by the formation of ferromagnetic clusters, as indicated by both the bulk magnetometric and spectroscopic data. - Graphical abstract: Temperature dependent evolution of the ESR spectrum for the (Cd{sub 0.56}Sb{sub 0.44})[Cr{sub 2}]Se{sub 4} single-crystal showing inhomogeneous nature of the ferromagnetic ordered state below T{sub c}=130 K. At temperature 127 K a fraction of the paramagnetic phase can still be observed.

36 MATERIALS SCIENCE↗

Composition and structure of acid leached LiMn{sub 2-y}Ti{sub y}O{sub 4} (0.2<=y<=1.5) spinels

Lithium manganese titanium spinels, LiMn{sub 2-y}Ti{sub y}O{sub 4}, (0.2<=y<=1.5) have been synthesized by solid-state reaction between TiO{sub 2} (anatase), Li{sub 2}CO{sub 3} and MnCO{sub 3}. Li{sup +} was leached from the powdered reaction products by treatment in excess of 0.2 N HCl at 85 deg. C for 6 h, under reflux. The elemental composition of the acidic solution and solid residues of leaching has been determined by complexometric titration, atomic absorption spectroscopy and X-ray fluorescence analysis. Powder X-ray diffraction was used for structural characterization of the crystalline fraction of the solid residues. It has been found that the amount of Li{sup +} leached from LiMn{sub 2-y}Ti{sub y}O{sub 4} decreases monotonically with increasing y in the interval 0.2<=y<=1.0 and abruptly drops to negligibly small values for y>1.0. The content of Mn and Li in the liquid phase and of Mn and Ti in the solid (amorphous plus crystalline) residue, were related to the composition and cation distribution in the pristine compounds. A new formal chemical equation describing the process of leaching and a mechanism of the structural transformation undergone by the initial solids as a result of Li{sup +} removal has been proposed. - Graphical abstract: Schematic representation of the acid leaching of LiMn{sub 2-y}Ti{sub y}O{sub 4} (0.2<=y<=1.0).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Full potential study of the elastic, electronic, and optical properties of spinels MgIn{sub 2}S{sub 4} and CdIn{sub 2}S{sub 4} under pressure effect

The structural, elastic, electronic, and optical properties of cubic spinel MgIn{sub 2}S{sub 4} and CdIn{sub 2}S{sub 4} compounds have been calculated using a full relativistic version of the full-potential linearized-augmented plane wave with the mixed basis FP/APW+lo method. The exchange and correlation potential is treated by the generalized-gradient approximation (GGA). Moreover, the Engel-Vosko GGA formalism is also applied to optimize the corresponding potential for band structure calculations. The ground state properties, including the lattice constants, the internal parameter, the bulk modulus, and the pressure derivative of the bulk modulus are in reasonable agreement with the available data. Using the total energy-strain technique, we have determined the full set of first-order elastic constants C{sub ij} and their pressure dependence, which have not been calculated or measured yet. The shear modulus, Young's modulus, and Poisson's ratio are calculated for polycrystalline XIn{sub 2}S{sub 4} aggregates. The Debye temperature is estimated from the average sound velocity. Electronic band structures show a direct band gap ({Gamma}-{Gamma}) for MgIn{sub 2}S{sub 4} and an indirect band gap (K-{Gamma}) for CdIn{sub 2}S{sub 4}. The calculated band gaps with EVGGA show a significant improvement over the GGA. The optical constants, including the dielectric function {epsilon}({omega}), the refractive index n({omega}), the reflectivity R({omega}), and the energy loss function L({omega}) were calculated for radiation up to 30 eV. -- Graphical abstract: Calculated total and partial densities of states for MgIn{sub 2}S{sub 4} and CdIn{sub 2}S{sub 4}

36 MATERIALS SCIENCE↗

Nanostructured dimagnesium manganese oxide (Spinel): Control of size, shape and their magnetic and electro catalytic properties

Tetravalent Mn based ternary oxides are of interest as they are important electrode materials. Dimagnesium manganate (Mg{sub 2}MnO{sub 4}) is one Mn(IV) containing oxide which has been of interest. Nanostructures of the above oxide (spinel) have been obtained by the thermal decomposition of nanostructured metal oxalate precursor at 500 Degree-Sign C. The size and anisotropy of the oxide nanostructures was controlled by choosing appropriate decomposition temperature of the oxalate precursor. Mg{sub 2}MnO{sub 4} nanorods were obtained at low temperature (500 Degree-Sign C), formed by aligned nanoparticles of size{approx}8-10 nm. These nanoparticles show Curie-Weiss behavior with Weiss constant (14 K). Below {approx}50 K there is a small deviation resulting in a negative Weiss constant (-7.36 K) indicating exchange cross over (from ferromagnetic like interactions to antiferromagnetic interactions). The high temperature magnetic moment corresponds to Mn (IV). Electrochemical experiments show that nanostructured Mg{sub 2}MnO{sub 4} is an efficient anode material for oxygen evolution reaction with a current density of 14 mA/cm{sup 2}. The stability of the anode over several cycles of oxidation and reduction is highly encouraging. - Graphical abstract: Nanostructured dimagnesium manganese with efficient electrocatalytic property synthesized by reverse micellar route. Highlights: Black-Right-Pointing-Pointer Mg{sub 2}MnO{sub 4} nanorods were synthesized by reverse micellar route. Black-Right-Pointing-Pointer Anisotropy of oxalate rods retained in oxides nanorods. Black-Right-Pointing-Pointer Nanorods show good catalytic behavior towards oxygen evolution reaction.

36 MATERIALS SCIENCE↗

Photoluminescence of titanium-doped zinc spinel blue-emitting nanophosphors

A blue-emitting phosphor of titanium-doped zinc spinel (ZnAl{sub 2}O{sub 4}:Ti; Ti=0–6.0 mol% in relation to Al) nanopowders was prepared by a simple sol–gel method. On annealing at 1000 °C, single-phase ZnAl{sub 2}O{sub 4}:Ti powders had primary particles of 25–30 nm in size and most Ti ions in the form of Ti{sup 4+}. Under UV excitation at 280 nm, a strong and broad blue emission centered at 435 nm was observed. The sources of the excitation and emission were assigned to the charge-transfer excitation and recombination between O{sup 2–}–Ti{sup 4+} and Ti{sup 3+}–O{sup –} ion pairs. Optimum brightness occurred at a doping of 2.0 mol% Ti. The decay lifetime of ZnAl{sub 2}O{sub 4}:2%Ti was calculated to be 3.0 ms for the blue emission with CIE coordinates of x=0.168 and y=0.153. The results suggest that ZnAl{sub 2}O{sub 4}:Ti is a promising candidate for application as a blue component phosphor for UV-converting white light-emitting diodes. - Graphical abstract: The absorption band around 270 nm is associated with the charge-transfer processes between octahedral Ti{sup 4+} and O{sup 2−} ions. The excitation band around 280 nm corresponds to the charge-transfer excitations from O{sup 2–}(2p){sup 6} electrons to Ti{sup 4+} (3d{sup 0}). Under 280 nm excitation, the PL spectrum shows a strong blue emission with a peak at around 435 nm. - Highlights: • Single-phase ZnAl{sub 2}O{sub 4}:Ti nanocrystals have been synthesized by a sol–gel process. • Under UV excitation at 280 nm, the blue emission centered at 435 nm is observed. • Blue emission is attributed to a charge-transfer transition involving the Ti{sup 4+} ions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of Sm{sup 3+} ions on structural, optical and solar light driven photocatalytic activity of spinel MnFe{sub 2}O{sub 4} nanoparticles

In this article, co-precipitation method was used to produce a series of samarium substituted manganese ferrite nanoparticles, MnFe{sub 2−x}Sm{sub x}O{sub 4} (x = 0.0, 0.5, 1.0, 1.5, 2.0) with oleic acid as surfactant. The effect of Sm{sup 3+} substitution and calcination temperature on the MnFe{sub 2}O{sub 4} was explored. The MnFe{sub 2−x}Sm{sub x}O{sub 4} sample calcinated at 973 K induced an enhanced optical behaviour. The influence of Sm{sup 3+} ions on cationic distribution and optical properties of MnFe{sub 2}O{sub 4} were probed by various physicochemical techniques. The presence of secondary orthorhombic (SmFeO{sub 3}) phase with initial cubic phase was confirmed by doublet peak in the X-ray diffraction pattern. The particle size distribution of MnFe{sub 0.5}Sm{sub 1.5}O{sub 4} sample was about 40 nm from HRTEM. The visible light absorption ability extended as Sm content was increased up to x = 1.5 in MnFe{sub 2}O{sub 4}. At an optimum concentration of Sm as x = 1.5 in MnFe{sub 2}O{sub 4}, photocatalyst exhibited decrease in energy band gap (1.64 eV); as a result effective visible light driven photocatalytic activity was achieved than the pure MnFe{sub 2}O{sub 4}. The MnSm{sub 1.5}Fe{sub 0.5}O{sub 4} sample exhibits pronounced photodegradation towards Rose Bengal with in 50 min under direct sunlight illumination as energy input. The broad emission band is observed in the entire photoluminescence (PL) spectrum. Current study provides an excellent competency of rare earth substituted ferrite as a new class of photocatalyst and they found to be a beneficial in the field of environmental cleaning application. - Highlights: • MnSm{sub x}Fe{sub 2−x}O{sub 4} nanoparticles were synthesised by co-precipitation method. • The insertion of Sm{sup 3+} ion in the MnFe{sub 2}O{sub 4} spinel matrix shows an increase in lattice parameter. • The calcination temperature is sensitive knob for tuning the optical properties of the MnFe{sub 2−x}Sm{sub x}O{sub 4} photocatalyst. • The MnFe{sub 2−x}Sm{sub x}O{sub 4} calcinated at 973 K shows enhanced optical behaviour. • The composition MnFe{sub 0.5}Sm{sub 1.5}O{sub 4} showed substantial red shift in absorption edge with narrow band gap of 1.64 eV.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Room temperature Moessbauer characterization of ferrites with spinel structure

Co- and Ga-doped magnetites were synthesized at room temperature and CoFe{sub 2}O{sub 4} was synthesized at 60 deg. C. They were analyzed by Moessbauer analysis, X-ray diffraction, scan electron microscopy as well as magnetization determination. The information of composition, cation distribution in the spinel structure and the particle size distribution of the products were obtained. Meanwhile, the formation mechanism of Co-doped magnetite was deduced. Two different procedures were used to precipitate CoFe{sub 2}O{sub 4} magnetic particles. One was named normal pH regulation procedure (A) in which alkaline solution was dropped into the mixture solution of metal ions and the other was denoted as reverse pH regulation procedure (B) in which mixture solution of metal ions were dropped into alkaline solution. Particles of uniform size were obtained in procedure A, which resulted from calculated average particle size and Moessbauer analysis. A comparative original method for investigating the magnetic nanoparticle size distribution was developed.

36 MATERIALS SCIENCE↗

Crystal and magnetic structure and cation distribution of Mn{sub 2-x}V{sub 1+x}O{sub 4} spinels (x = 0, 1/3 and 1)

We synthesized the spinel-type compounds belonging to the Mn{sub 2-x}V{sub 1+x}O{sub 4} series with x = 0, 1/3 and 1 as polycrystalline powders. Crystal and magnetic structures were refined using synchrotron X-ray and neutron powder diffraction. At 300 K all members crystallize in the cubic system, space group Fd3-bar m, and show a structural transition at low temperature, changing to a tetragonal symmetry (space group I4{sub 1}/amd). Cations distributions between octahedral and tetrahedral sites were refined from neutrons diffraction (ND) data and explained based on crystal field stabilization energies (CFSE) and ionic radii. The magnetic unit cell is the same as the crystallographic one, having identical symmetry relations. The magnetic structure was refined as an arrangement of collinear spins, antiferromagnetically ordered, parallel to the c-axis of the unit cell. The refined site magnetic moments are smaller than those obtained from hysteresis cycles of the M vs. H measurements, indicating that some non-collinear disordered component coexists with the ordered component along the c-axis.

36 MATERIALS SCIENCE↗

Microstructure and DC electrical conductivity of spinel nickel ferrite sintered in air and nitrogen atmospheres

In recent years, the development of inert anode materials has gained considerable attention because such materials are capable of producing only environment-friendly O{sub 2} and saving energy during aluminum electrolysis. Nickel ferrite was prepared by a solid-state reaction as the inert anode in this study and its microstructures and direct current conductivities were analyzed in detail regarding the effects of different sintering atmospheres. A single-phase spinel structure was confirmed for all samples by X-ray powder diffraction. The grain sizes and the relative densities of the samples sintered in nitrogen increased by over 7 {mu}m and 10.8%, respectively, compared to those sintered in air. The direct current conductivities of the samples sintered in nitrogen showed a drastic increase compared to those sintered in air, believed to be due to the effects of increased Fe{sup 2+} ion concentration at octahedral sites and the increase of the relative density.

36 MATERIALS SCIENCE↗