Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Microstructure Development of 308L Stainless Steel During Additive Manufacturing

$In$ $situ$ high-energy X-ray diffraction measurements were completed during deposition of 308L stainless steel wire onto a 304L stainless steel substrate. Attempts were made to extract microstructural features such as phase fraction and internal stress, as well as temperature evolution immediately following the deposition. The limited data that could be collected during deposition and rapid solidification are critically examined. High-energy X-rays coupled with relatively slow detectors were utilized to enable determination of orientation-dependent lattice parameters accurately enough to comment on phase strain evolution between austenite and ferrite. Here, information about the hydrostatic and deviatoric stress states of the constituent phases was determined on time scales that are relevant to their development. However, the time resolution of the technique was insufficient to monitor phase evolution during the solid–solid phase transformation and, more so, during solidification. Moreover, the accurate and absolute determination of inherently statistical parameters, such as phase fraction, depends critically on the ability to sample a statistically significant numbers of grains in the microstructure.

36 MATERIALS SCIENCE↗

Microstructure, microstructural stability and mechanical properties of sand-cast Mg–4Al–4RE alloy

This paper presents a methodology for assessing the phase composition and the results of structural stability tests of the sand-cast Mg–4Al–4RE alloy after annealing it at 175 and 250 °C for 3000 h. The microstructure was analyzed with optical, scanning electron, and transmission electron microscopy. The phase composition was determined with X-ray diffraction. The structure of the Mg–4Al–4RE (AE44) alloy is composed of large grains of α-Mg solid solution, needle-shaped precipitates of the Al{sub 11}RE{sub 3}phase, polyhedral precipitates of the Al{sub 2}RE phase and Al{sub 10}RE{sub 2}Mn{sub 7} phase. After annealing at 175 °C for 3000 h, no changes in the alloy structure are observed, whereas after annealing at 250 °C the precipitates of the Al{sub 11}RE{sub 3} phase are found to be in the initial stages of spheroidization. The coarse-grained structure and unfavorable morphology of the intermetallic phases in the sand-cast AE44 alloy, which are caused by low solidification rates, result in low creep resistance up to 200 °C and low mechanical properties at ambient temperature and at 175 °C. - Highlights: • Complement the knowledge about the microstructure of Mg-Al-RE alloys. • Clarify the mechanism of formation of Mg17Al12 phase above 180 °C. • Applying a chemical dissolution of the α-Mg in order to phase identification. • Applying a statistical test to assess the spheroidization of precipitates. • Quantitative description of microstructure of Mg-Al-RE alloys.

36 MATERIALS SCIENCE↗

Development of Stretch Flangeable Grade Steels by Inclusion Engineering Approach

The demand for good stretch flangeability in high-strength automotive steels has necessitated due attention on steel cleanliness and processes. The presence of elongated MnS stringers and centerline segregation of nonmetallic inclusions adversely affects the transverse mechanical property. In the present investigation, stretch flangeability of industrially produced steel, with and without Ca treatment, has been compared with Ti-added steel, produced at 40 kg scale without Ca treatment. The study brings out the influence of centerline segregation and modification of nonmetallic inclusions on HER performance. The microstructural analysis of industrial steel revealed that the method of hole formation (punching/drilling) determines crack initiation mechanism. The inclusions, along with the second phase present in the centerline, drive the crack propagation. An addition of Ti in liquid steel promotes formation of Al-Ti-O-based oxide, prior to MnS precipitation, during solidification and acts as nucleation site for MnS inclusion. This obviates the elongated stringer-type MnS inclusions. The centerline segregation-free Ti-modified steel, prepared at the laboratory scale, showed consistent HER property compared with industrial steel. It is also concluded that calcium treatment can be circumvented by modifying the sulfide stringer with the addition of Ti in the steel for further improvement in HER property.

36 MATERIALS SCIENCE↗

Process-structure-property considerations for wire-based directed energy deposition of Ti-6Al-4V

Directed energy deposition (DED) is an attractive additive manufacturing (AM) process for large structural components. The rapid solidification and layer-by-layer process associated with DED results in non-ideal microstructures, such as large grains with strong crystallographic textures. These non-ideal microstructures can lead to severe anisotropy in the mechanical properties. Despite these challenges, DED has been identified as a potential solution for the manufacturing of near net shape Ti-6Al-4V preforms, replacing lost casting and forging capabilities. Two popular wire-based directed energy deposition (W-DED) processes were considered for the manufacturing of Ti-6Al-4V with assessments on their respective metallurgical and mechanical properties, as compared to a conventionally processed material. The two W-DED processes explored were wire arc additive manufacturing (WAAM) and electron beam additive manufacturing (EBAM). High throughput inspection and tensile testing procedures were utilized to generate statistically relevant data sets related to each process and sample orientation. The 2 AM technologies produced material with remarkably different microstructures and mechanical properties. Importantly, results revealed key differences in strength and ductility for the two disparate processes which were found to be related to differences in the metallurgical properties.

36 MATERIALS SCIENCE↗

Plasma Sprayed Hydroxyapatite Coatings: Influence of Spraying Power on Microstructure

The plasma sprayed hydroxyapatite (HA) coatings are used on metallic implants to enhance the bonding between the implant and bone in human body. The coating process was implemented at different spraying power for each spraying condition. The coatings formed from a rapid solidification of molten and partly molten particles that impact on the surface of substrate at high velocity and high temperature. The study was concentrated on different spraying power that is between 23 to 31 kW. The effect of different power on the coatings microstructure was investigated using scanning electron microscope (SEM) and phase composition was evaluated using X-ray diffraction (XRD) analysis. The coatings surface morphology showed distribution of molten, partially melted particles and some micro-cracks. The produced coatings were found to be porous as observed from the cross-sectional morphology. The coatings XRD results indicated the presence of crystalline phase of HA and each of the patterns was similar to the initial powder. Regardless of different spraying power, all the coatings were having similar XRD patterns.

36 MATERIALS SCIENCE↗

Solidification Behavior of Calcium Ferrite Under Ultrasonic Vibration

Ultrasonic vibration was applied to the solidification process of calcium ferrite (CF) to modify the grain size and improve the homogeneity of the solidified microstructure. The effects of ultrasound on microstructure, density, compressive strength, and reducibility were studied. The acoustic pressure decreased and then increased along the axis symmetry due to the attenuation of acoustic pressure and reflection of ultrasonic waves in the melt under a fixed power. When the ultrasonic power was increased, the general acoustic pressure increased, which was beneficial to the avoidance of macropores and to improvement of the microstructure. Coarse acicular CF grains were significantly refined; the grain size decreased from 1967 to 442 μm when the ultrasonic power was increased from 0 to 300 W. The density of the samples increased from 4370 to 4680 kg/m{sup 3} due to cavitation and acoustic streaming effects. Ultrasonic vibration greatly improved the ultimate compressive strength of CF; the values were 41.8 ± 2.1 to 67.3 ± 3.4 MPa for ultrasonic powers of 100 to 300 W, respectively. Without ultrasonic treatment, it was only 37.4 ± 1.9 MPa. Ultrasonic vibration also influenced the reduction time of CF due to the composition segregation in the slag during solidification.

36 MATERIALS SCIENCE↗

Solubility and microstructure in the pseudo-binary PbTe-Ag{sub 2}Te system

The solvus lines of the PbTe and Ag{sub 2}Te phases in the pseudo-binary PbTe-Ag{sub 2}Te system have been determined using diffusion couples and unidirectional solidification by the Bridgman method. The solubilities of both Ag{sub 2}Te in PbTe and PbTe in Ag{sub 2}Te decrease with decrease in temperature. For the former, this change is from 14.9 at% Ag (694 deg. C) to 0.5 at% Ag (375 deg. C), while for the latter it is from 12.4 at% Pb (650 deg. C) to 3.1 at% Pb (375 deg. C). The decrease in solubilities leads to the formation of precipitates of Ag{sub 2}Te in PbTe and PbTe in Ag{sub 2}Te. In particular, fast atomic diffusion in Ag{sub 2}Te results in the precipitation of PbTe even in quenched samples. From the temperature dependence of these solubilities, heats of solution have been determined. In the diffusion couple, the phase boundary moves toward PbTe. In the region between the phase boundary and the initial interface, PbTe transforms to {beta}-Ag{sub 2}Te (cubic) retaining the cube-on-cube orientation relationship. - Graphical abstract: The precipitation in the diffusion couple in fast cooling suggests high chemical diffusivity. The large heat of solution for the Ag{sub 2} Te dissolution in PbTe leads to fine microstructure. Highlights: > The solvus lines were determined by diffusion couples and unidirectional solidification. > The solubilities in both phases decrease with decrease in temperature. > Chemical diffusivity in Ag2Te phase is high. > Heat of solution is one of the key parameters to control the number density of precipitates. > The Ag2Te phase transformed from PbTe in diffusion couples holds the cube-on-cube relationship.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Materials for Advanced Ultrasupercritical Steam Turbines Task 4: Cast Superalloy Development

The Steam Turbine critical stationary structural components are high integrity Large Shell and Valve Casing heavy section Castings, containing high temperature steam under high pressures. Hence to support the development of advanced materials technology for use in an AUSC steam turbine capable of operating with steam conditions of 760°C (1400°F) and 35 Mpa (5000 psia), Casting alloy selection and evaluation of mechanical, metallurgical properties and castability with robust manufacturing methods are mandated. Alloy down select from Phase 1 based on producability criteria and creep rupture properties tested by NETL-Albany and ORNL directed the consortium to investigate cast properties of Haynes 282 and Haynes 263. The goals of Task 4 in Phase 2 are to understand a broader range of mechanical properties, the impact of manufacturing variables on those properties. Scale up the size of heats to production levels to facilitate the understanding of the impact of heat and component weight, on metallurgical and mechanical behavior. GE Power & Water Materials and Processes Engineering for the Phase 2, Task 4.0 Castings work, systematically designed and executed casting material property evaluation, multiple test programs. Starting from 15 lbs. cylinder castings to world’s first 17,000 lbs. poured weight, heavy section large steam turbine partial valve Haynes 282 super alloy casting. This has demonstrated scalability of the material for steam Turbine applications. Activities under Task 4.0, Investigated and characterized various mechanical properties of Cast Haynes 282 and Cast Nimonic 263. The development stages involved were: 1) Small Cast Evaluation: 4 inch diam. Haynes 282 and Nimonic 263 Cylinders. This provided effects of liquidus super heat range and first baseline mechanical data on cast versions of conventional vacuum re-melted and forged Ni based super alloys. 2) Step block castings of 300 lbs. and 600 lbs. Haynes 282 from 2 foundry heats were evaluated which demonstrated the importance of proper heat treat cycles for Homogenization, and Solutionizing parameters selection and implementation. 3) Step blocks casting of Nimonic 263: Carried out casting solidification simulation analysis, NDT inspection methods evaluation, detailed test matrix for Chemical, Tensile, LCF, stress rupture, CVN impact, hardness and J1C Fracture toughness section sensitivity data and were reported. 4) Centrifugal Casting of Haynes 282, weighing 1400 lbs. with hybrid mold (half Graphite and half Chromite sand) mold assembly was cast using compressor casing production tooling. This test provided Mold cooling rates influence on centrifugally cast microstructure and mechanical properties. Graphite mold section out performs sand mold across all temperatures for 0.2% YS; %Elongation, %RA, UTS at 1400°F. Both Stress-LMP and conditional Fracture toughness plots data were in the scatter band of the wrought alloy. 5) Fundamental Studies on Cooling rates and SDAS test program. Evaluated the influence of 6 mold materials Silica, Chromite, Alumina, Silica with Indirect Chills, Zircon and Graphite on casting solidification cooling rates. Actual Casting cooling rates through Liquidus to Solidus phase transition were measured with 3 different locations based thermocouples placed in each mold. Compared with solidification simulation cooling rates and measurement of SDAS, microstructure features were reported. The test results provided engineered casting potential methods, applicable for heavy section Haynes 282 castings for optimal properties, with foundry process methods and tools. 6) Large casting of Haynes 282 Drawings and Engineering FEM models and supplemental requirements with applicable specifications were provided to suppliers for the steam turbine proto type feature valve casing casting. Molding, melting and casting pouring completed per approved Manufacturing Process Plan during 2014 Q4. The partial valve casing was successfully cast after casting methods were validated with solidification simulation analysis and the casting met NDT inspection and acceptance criteria. Heat treated and sectioned to extract trepan samples at different locations comparing with cast on coupons test data. Material properties requisite for design, such as tensile, creep/rupture, LCF, Fracture Toughness, Charpy V-notch chemical analysis testing were carried out. The test results will be presented in the final report. The typical Haynes 282 large size Steam Turbine production casting from Order to Delivery foundry schedule with the activity break up is shown in Figures 107 and 108. • From Purchase Order placement to Casting pouring ~ 26 weeks. 1. Sales and commercial review 3 2. Engineering Drawings/models review 4 3. Pattern and core box manufacturing 6 4. Casting process engineering review 4 5. FEM and solidification simulation analysis 4 6. Gating & Feeder Attachments, Ceramic tiling 2 7. Molding and coremaking production scheduling 6 8. Melting planning and schedule 3 9. Pouring, cooling and shake out 2 • From Pouring to casting Delivery ~ 29 weeks 10. Shot blast and riser cutting, gates removal 3 11. Homogenizing , solutionizing HT furnace prep 4 12. Grinding, Fettling 2 13. Aging HT Cycle, cooling 2 14. VT and LPT NDT inspections 2 15. Radiographic inspection 4 16. Mechanical testing, Chemical analysis test certs 4 17. Casting weld repair upgrades and Aging PWHT 4 18. NDT after weld repairs and casting upgrades 3 19. Casting Final Inspection and test certifications 3 20. Package and delivery 2 Hence the Total Lead time from P.O to Casting delivery is approximately 55 weeks. The Task 4.2 and Task 4.3 activities and reporting completed.

Thangirala, Mani↗

Senary refractory high-entropy alloy Cr x MoNbTaVW

This paper demonstrates that a senary refractory high-entropy alloy Cr x MoNbTaVW can be tailored over a certain range of Cr content with the BCC structure for different microstructures and physical properties, assisted by CALPHAD simulations. Microstructure characterizations are performed using X-ray diffraction and scanning electron microscopy. Chemical microsegregation during solidification predicted using the Scheil model generally agrees with the experimental results. The lattice constant, density, and Vickers’ micro-hardness of the highentropy alloy samples in the as-cast state are measured and discussed. For Cr x MoNbTaVW, x=2.0 case appears exceeding the upper limit of maintaining a single BCC phase HEA, determined by the XRD patterns. The elemental dependence of the mixing thermodynamic properties (entropy, enthalpy and Gibbs energy) in BCC phase in the senary system is analyzed. The calculated entropy of mixing and enthalpy of mixing for CrMoNbTaVW are 14.7 J/K/mol and -662.5 J/mol respectively.

36 MATERIALS SCIENCE↗

Assessment of phase constitution on the Al-rich region of rapidly solidified Al-Co-Fe-Cr alloys

The formation of quasicrystalline approximants in rapidly solidified Al-Co-Fe-Cr alloys was investigated. Alloys of atomic composition Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8}, Al{sub 77}Co{sub 11}Fe{sub 6}Cr{sub 6} and Al{sub 76}Co{sub 19}Fe{sub 4}Cr{sub 1} were produced using melt spinning and arc melting methods and their microstructural characterization was carried out by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Up to the present there is no consensus in the literature regarding the formation of quasicrystalline phase or quasicrystalline approximants in the Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8} alloy. This work presents, for the first time, a detailed structural characterization of selected alloys in the Al-Co-Fe-Cr system close to the atomic composition Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8}. The results indicated the samples to be composed, mostly, by two intermetallic phases, which are quaternary extensions of Al{sub 5}Co{sub 2} and Al{sub 13}Co{sub 4} and are quasicrystalline approximants. Although the Al{sub 5}Co{sub 2} phase has already been reported in the Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8} alloy, the presence of the monoclinic Al{sub 13}Co{sub 4} is now identified for the first time in the as cast state. In the binary Al-Co system a quasicrystalline phase is known to form in a rapidly solidified alloy with composition close to the monoclinic and orthorhombic Al{sub 13}Co{sub 4} phases. This binary quasicrystalline phase presents an average valence electron per atom (e/a) between 1.7 and 1.9; thus, in addition to the Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8} alloy, the compositions Al{sub 77}Co{sub 11}Fe{sub 6}Cr{sub 6} and Al{sub 76}Co{sub 19}Fe{sub 4}Cr{sub 1} were chosen to be within the region of formation of the quaternary extension of the Al{sub 13}Co{sub 4} phase and also within the (e/a) of 1.7 to 1.9. However, no quasicrystalline phase is present in any of the studied alloys. The Al-Co-Fe-Cr system, around the compositions studied, is composed of quaternary extensions of Al-Co intermetallic phases, which present solubility of Fe and Cr at Co atomic sites. - Highlights: •The Al rich region of the AlCoFeCr system is studied concerning phase formation on rapidly solidified alloys. •The alloys were composed mostly by quaternary extensions of Al-Co intermetallic phases. •Al{sub 5}Co{sub 2} and Al{sub 13}Co{sub 4} were the major phases observed in the alloys and are approximants of a quasicrystalline phase. •No quasicrystalline phase was observed in the Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8} composition.

36 MATERIALS SCIENCE↗

Characterization of texture and grain boundary character distributions of selective laser melted Inconel 625 alloy

Highlights: • <110> texture along layer build direction was generated in as-SLMed Inconel 625. • The stress relief process dominates texture and GBCD evolution. • SLMed IN 625 alloy can be GBEed via suitable post annealing. - Abstract: Select laser melting (SLM) is one of the practical metal additive manufacturing processes to fabricate complex structures. The inhomogeneous microstructure and high residual stress are typically resulted from a non-uniform melting and rapid solidification during a SLM process, which has the significant impact on part dimensional instability, corrosion resistance, and mechanical properties. The bulk of current research is limited to the general characterization of grain size, texture, and mechanical properties. However, grain boundary character distribution (GBCD) and its relationship with texture are yet to be understood. This study has shown that the preferred <110> along building direction and <100> along laser scanning direction were produced. The high density of low angle grain boundary (LAGB) can be an indicator of residual stress levels in the as-SLMed samples. The newly-developed ∑3, ∑9 and ∑27 grain boundaries were heavily populated, and the cluster of grains interfaced by ∑3{sup n} (n = 0, 1, 2…) was introduced at the expense of LAGB only at high recrystallization annealing (1150°C or over). The research results suggest that GBCD optimization be possible in the SLMed Inconel 625 alloy via suitable post annealing, which allows improving intergranular corrosion resistance and enhancing mechanical properties.

36 MATERIALS SCIENCE↗

Ternary eutectic growth of nanostructured thermoelectric Ag-Pb-Te materials

Nanostructured Ag-Pb-Te thermoelectric materials were fabricated by unidirectionally solidifying the ternary Ag-Pb-Te eutectic and near-eutectic alloys using the Bridgeman method. Specially, the Bridgman-grown eutectic alloy exhibited a partially aligned lamellar microstructure, which consisted of Ag{sub 5}Te{sub 3} and Te phases, with additional 200-600 nm size particles of PbTe. The self-assembled interfaces altered the thermal and electronic transport properties in the bulk Ag-Pb-Te eutectic alloy. Presumably due to phonon scattering from the nanoscale microstructure, a low thermal conductivity ({kappa} = 0.3 W/mK) was achieved of the eutectic alloy, leading to a zT peak of 0.41 at 400 K.

36 MATERIALS SCIENCE↗

Additive Manufactured Composite Phase-Change Material for Thermal Energy Storage Applications

Phase-change materials play a critical role in industrial energy storage applications to drive efficiency improvements, thermal energy management, and carbon emissions reductions. Recently, it has been shown that rapid solidification of alloys with metastable immiscibility in the liquid phase has the potential to form unique microstructures in which a low-melting phase is uniformly distributed in a high-melting matrix. This feature can be exploited using additive manufacturing to produce components with complex geometries containing such unique phase-change microstructures. Phase-field simulations utilizing high-performance computing were used to provide a detailed description of the evolution of the active phase during service in terms of their morphology and composition in different polycrystalline matrix grain morphologies that are typically produced during additive manufacturing. Phase field simulations were performed using, MEUMAPPS-SL (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid Liquid) code that was developed in-house by the Oak Ridge National Laboratory. The simulations utilized the capabilities of the Kestrel supercomputer at the National Renewable Energy Laboratory. The simulation results were compared with experimental results generated at Siemens Energy, Inc. The results indicate that the kinetics of liquid spreading along grain boundaries is largely determined by the mobility of the triple line along the intersection of the grain boundary liquid and the grain boundary plane.

25 ENERGY STORAGE↗

Splat Quenching as a High Throughput Rapid Solidification Testing Method for Developing Additive Manufacturing Alloys

Splat quenching as a high throughput rapid solidification screening tool is evaluated. Samples were made using known alloys (SS316, IN625, Ti-5553) to evaluate and establish the microstructures for a variety of alloy systems as well as the predicted cooling rates. The samples are inductively heated and levitated prior to being struck between two platens that produce a high contact pressure and a thin sample resulting in cooling rates on the order of 10 6 to 10 7 K/s. Process parameters were evaluated with analytical models in addition to numerical simulations to provide an effect of process variables such as substrate material, melt superheat, and platen velocity on the resulting solidification. The splat thickness was found to be controlled by platen velocity, melt superheat, as well as the feedstock volume. The sample thickness is the key controlling factor for varying the average cooling rate experienced by the splat quenched sample. The splat quenching techniques can reach regions of rapid solidification space that meet and exceed laser and electron beam techniques across the sample. In conclusion, the results of the study provide a useful foundation in understanding the splat quenching technique and its potential as a low effort tool to explore rapid solidification effects on alloys.

Alloy Design↗

Localized Strain Analysis of Ce- and Mg-Treated Cast Iron under Uniaxial Compression

Cast iron exhibits a wide range of mechanical properties, depending on its microstructural features. The microstructure of cast iron consists of several microconstituents with different elastic-plastic behavior, making the strain non-uniform across the bulk material. To understand the individual effects of these microconstituents on the overall mechanical behavior, local strain analysis using digital image correlation analysis was carried out. Samples with two different compositions (varying cerium, magnesium and silicon) were processed at different solidification velocities in a Bridgman furnace. Sections of the directionally solidified samples were loaded under uniaxial compression to measure global and local strain behavior. Despite the variability of the microstructure, the stress–strain curves obtained by digital image correlation (DIC) were found to react in a well-controlled way to changes in solidification velocity. It was observed that high-strain failure (greater than 15%) was accompanied by local straining of the softer ferritic phase, but during low-strain failure, local straining was not prominent. Higher nodularities, due to higher solidification velocities, raised the compressive strength without affecting the toughness significantly. Higher percentages of carbides led to higher compressive strengths with corresponding losses in ductility. The continuity of the matrix was also found to play an important role in the behavior during compression.

ductile failure↗

Microstructural characteristics and corrosion behavior of a super duplex stainless steel casting

The machining of super duplex stainless steel castings is usually complicated by the difficulty involved in maintaining the dimensional tolerances required for given applications. Internal stresses originating from the solidification process and from subsequent heat treatments reach levels that exceed the material's yield strength, promoting plastic strain. Stress relief heat treatments at 520 deg. C for 2 h are an interesting option to solve this problem, but because these materials present a thermodynamically metastable condition, a few precautions should be taken. The main objective of this work was to demonstrate that, after solution annealing at 1130 deg. C and water quenching, stress relief at 520 deg. C for 2 h did not alter the duplex microstructure or impair the pitting corrosion resistance of ASTM A890/A890M Grade 6A steel. This finding was confirmed by microstructural characterization techniques, including light optical and scanning electron microscopy, and X-ray diffraction. Corrosion potential measurements in synthetic sea water containing 20,000 ppm of chloride ions were also conducted at three temperatures: 5 deg. C, 25 deg. C and 60 deg. C.

36 MATERIALS SCIENCE↗

Microstructure and Hard Magnetic Properties of Sm 1-x Zr x (Fe,Co) 11.3-y Ti 0.7 By Ingots and Thick Melt-Spun Ribbons

Permanent magnets made from Sm(Fe,Co) 12 -based compounds are being actively pursued through nanostructuring and powder metallurgy. This study was aimed at the development of hard magnetic properties in bulk as-cast alloys and in melt-spun alloys for very low wheel speeds. Slower solidification rates and alloying with Zr promote the tetragonal ThMn 12 -type crystal structure, whereas higher solidification rates and alloying with B replace the ThMn 12 structure type with the TbCu 7 structure type. When introduced simultaneously, Zr and B dramatically reduce the alloy solidification rates required for both the refinement of the 1:12 crystallites and their replacement with the 1:7 phase. In bulk arc-melted alloys, this allowed for a microstructure of separated 1:12 crystallites 1–3 μm in size, although, because of the ferromagnetic nature of a minority phase, the coercivity of these fine-grained alloys reached only 0.73 kOe. A moderately accelerated solidification further refined the 1:12 crystallites and increased the coercivity; a Sm 0.7 Zr 0.4 (Fe,Co) 10.8 Ti 0.7 B 0.5 alloy exhibited a coercivity of 1.5 kOe and a maximum energy product of 3.4 MGOe when it was melt-spun into a 0.26-mm-thick ribbon. A more rapid solidification suppressed the 1:12 phase and after annealing at 800–850 °C, the alloys modified with Zr and B developed reasonably high coercivity and maximum energy product even when melt-spun at a wheel speed of 6 m/s. For the above-mentioned alloy, these values were 4.1 kOe and 7.8 MGOe, respectively. Further, a similarly processed very-Sm-lean Sm 0.5 Zr 0.6 (Fe,Co) 10.6 Ti 0.7 B 0.7 alloy exhibited a remanence of 8.8 kG and an energy product of 7.4 MGOe.

36 MATERIALS SCIENCE↗

Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency

Strong chemical reactions between Al and Ce lead to the formation of intermetallics with exceptional thermal stability. The rapid formation of intermetallics directly from the liquid phase during solidification of Al-Ce alloys leads to an ultrafine microconstituent structure that effectively strengthens as-cast alloys without further microstructural optimization via thermal processing. Die casting is a high-volume manufacturing technology that accounts for greater than 40% of all cast Al products, whereas Ce is highly overproduced as a waste product of other rare earth element (REE) mining. Reducing heat treatments would stimulate significant improvements in manufacturing energy efficiency, exceeding (megatonnes/year) per large-scale heat-treatment line. In this study, multiple compositions were evaluated with wedge mold castings to test the sensitivity of alloys to the variable solidification rate inherent in high-pressure die casting. Once a suitable composition was determined, it was successfully demonstrated at 800 lbs/h in a 600-ton die caster, after which the as-die cast parts performed similarly to ubiquitous A380 in the same geometry without requiring heat treatment. Furthermore, this work demonstrates the compatibility of Al REE alloys with high-volume die-casting applications with minimal heat treatments.

36 MATERIALS SCIENCE↗