Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Microstructure and In Situ Observations of Undercooling for Nucleation of [beta]-Sn Relevant to Lead-Free Solder Alloys

Difficult nucleation of {beta}-Sn during solidification of tin and tin-based lead-free solder alloys can result in high degrees of undercooling of the liquid prior to solidification. The undercooling can produce solder joints with large grains, anisotropic behavior, and undesirable mechanical properties. This paper describes our examination of the amount of undercooling of tin on both graphite (non-wetting) and copper (wetting) surfaces using in situ x-ray diffraction. The microstructure was further characterized by optical microscopy, scanning electron microscopy, and electron backscattering diffraction imaging microscopy. Undercoolings as high as 61 C were observed for Sn solidified on graphite, while lower undercoolings, up to 30 C, were observed for Sn solidified on copper. The microstructure of the high purity Sn sample solidified on graphite showed very few grains in the cross-section, while the commercially pure Sn sample solidified with only one grain and was twinned. Tin solidified on copper contained significant amounts of copper in the tin, intermetallic phase formation at the interface, and a eutectic microstructure.

36 MATERIALS SCIENCE↗

Influence of Mn addition on the microstructure and mechanical properties of a directionally solidified γ-TiAl alloy

Highlights: • Mn addition can significantly improve the yield strength of TiAl alloy. • Introduction of Mn facilitates the operation of twinning-controlled deformation. • Twin-dislocation interactions cause a continuous increase in work hardening rate. - Abstract: TiAl alloys with nominal compositions of Ti-47Al-2Nb-2Cr-(0, 1, 3, 5)Mn were prepared via electromagnetic cold crucible directional solidification (ECCDS), and the influence of Mn addition on the microstructure and mechanical properties of the alloys was investigated. The experimental results showed that the Mn atoms were dissolved within the TiAl alloy, and no Mn compounds were formed. Based on the X-ray diffraction (XRD) analysis results, the peak angle of the Mn-containing sample shifted to a higher value, indicating lattice shrinkage. The Mn addition also increased the volume fraction of the B2 phase. The yield strength of the TiAl alloy monotonically increased as the content of the substitutional-solute Mn atoms increased. The ultimate strengths of the TiAl alloys containing 1 at.%, 3 at.%, and 5 at.% Mn consequently decreased because micro-cracks were preferentially formed in the B2 phase during room-temperature deformation. The introduction of substitutional-solute Mn atoms could result in a reduction of the stacking-fault energy of the γ phase, and facilitate the operation of twinning-controlled plastic-deformation during the intermediate stage of the plastic deformation process. The interaction between the deformation twins and movable dislocations led to a continuous increase in the work-hardening rate.

36 MATERIALS SCIENCE↗

Directional Solidification of Nodular Cast Iron

Cerium enhances formation of graphite nodules. Preliminary experiments in directional solidification of cast iron shows quantitative correlation of graphite microstructure with growth rate and thermal gradient, with sufficient spheroidizing element to form spheroidal graphite under proper thermal conditions. Experimental approach enables use of directional solidification to study solidification of spheriodal-graphite cast iron in low gravity. Possible to form new structural materials from nodular cast iron.

Curreri, P. A.↗

The microstructure of a selective laser melting (SLM)-fabricated NiTi shape memory alloy with superior tensile property and shape memory recoverability

A selective laser melting (SLM)-fabricated NiTi with superior tensile property and shape memory recoverability was obtained by using a unique stripe rotation scanning strategy. Here, the alloy characteristics, formation mechanisms and evolution in terms of twins, dislocations and precipitations of the alloy were systematically studied. Compared to the conventional smelting-followed-by-machining, the SLM fabrication process involves rapid solidification and repeated heating, which confer distinctive characteristics to the microstructures of SLM-fabricated NiTi alloys. Rapid solidification promotes the formation of a supersaturation solid solution matrix containing a high concentration vacancies, which in turn aggregate to generate a high density of dislocations. During subsequent repeated heating stages, these dislocations occur thermal motion along three directions of <001 > , <111> and <110 >, leading to the formation of thermal kinks, helical dislocations and wave morphology. Simultaneously, precipitated particles Ti 3 Ni 4 repeatedly nucleate and heterogeneous grow with the movement of dislocation. Such precipitation behavior, termed repeated precipitation, has not been previously reported in the conventional NiTi alloys, suggesting that it could be a unique characteristic of such alloy. After martensitic transformation, only two twins, {1 1¯ 1} type I twin and compound twin, are detected. The twinning lamellae of these two twins, where precipitation and dislocation pile-ups exist, often have uneven thickness and chaotic arrangement. Besides, the unique self-accommodated microstructures, such as secondary {1 1¯ 1} type I twin and compound twin with “herring-bone’’ lamellae, which often appear in the deformed or nanocrystalline NiTi, can also be observed. These unique microstructures may confer the distinctive properties to the SLM-fabricated NiTi.

36 MATERIALS SCIENCE↗

Influence of phase composition on microstructure and properties of Mg-5Al-0.4Mn-xRE (x = 0, 3 and 5 wt.%) alloys

The microstructure and mechanical properties investigations of two AME503 and AME505 experimental alloys in as-cast conditions were presented. The investigated materials were fabricated on the basis of the AM50 commercial magnesium alloy with 3 and 5 wt.% cerium rich mischmetal. In the as-cast condition, both experimental alloys were mainly composed of α-Mg, Al{sub 11}RE{sub 3} and Al{sub 10}RE{sub 2}Mn{sub 7} intermetallic phases. Additionally, due to non-equilibrium solidification conditions, a small amount of α + γ divorced eutectic and Al{sub 2}RE intermetallic phase were revealed. The obtained results also show a significant influence of rare earth elements on Brinell hardness, tensile and compression properties at ambient temperature and especially on creep properties at 473 K. Improved alloy properties with a rise in rare earth elements mass fraction results from an increase in Al{sub 11}RE{sub 3} phase volume fraction and suppression of α + γ eutectic volume fraction in the alloy microstructure. Additionally, the influence of rare earth elements on the dendrite arm space value was discussed. The presented results also proved the thermal stability of the intermetallic phases during creep testing. - Highlights: • Two different Mg-5Al-0.4Mn alloys containing 3 and 5 wt.% of rare earth elements were fabricated. • Addition of rare earth elements leads to a reduction of dendrite arm spaces. • Mechanical properties depend on the phase composition of the alloys. • The increase of the rare earth elements content causes rise of the creep resistance.

36 MATERIALS SCIENCE↗

Characterization of the Fe-Co-1.5V soft ferromagnetic alloy processed by Laser Engineered Net Shaping (LENS)

Processing of the low workability Fe-Co-1.5V (Hiperco® equivalent) alloy is demonstrated using the Laser Engineered Net Shaping (LENS) metals additive manufacturing technique. As an innovative and highly localized solidification process, LENS is shown to overcome workability issues that arise during conventional thermomechanical processing, enabling the production of bulk, near net-shape forms of the Fe-Co alloy. Bulk LENS structures appeared to be ductile with no significant macroscopic defects. Atomic ordering was evaluated and significantly reduced in as-built LENS specimens relative to an annealed condition, tailorable through selection of processing parameters. Fine equiaxed grain structures were observed in as-built specimens following solidification, which then evolved toward a highly heterogeneous bimodal grain structure after annealing. The microstructure evolution in Fe-Co is discussed in the context of classical solidification theory and selective grain boundary pinning processes. In conclusion, magnetic properties were also assessed and shown to fall within the extremes of conventionally processed Hiperco® alloys.

36 MATERIALS SCIENCE↗

Microstructural evolution and growth behavior of intermetallic compounds at the liquid Al/solid Fe interface by synchrotron X-ray radiography

Highlights: • A layered and tongue-like η phase was in-situ observed by synchrotron radiation X-ray radiography. • The coalescence of η phase bottom resulted in dissolution, further increasing the growth rate. • The θ phase growth behavior with different morphologies during cooling was analyzed. - Abstract: The growth of Inter-Metallic Compounds (IMCs) with dissolution was investigated on the liquid Al/solid Fe interconnection by using synchrotron radiation real-time imaging technology. At the initial stage of holding at 850 °C, a layer of the η-Fe{sub 2}Al{sub 5} phase formed at the interface, and tongue-like η grew into α-Fe. The tongue-like η phase had a stronger (001) texture than the layered phase. The coalescence of tongue-like η started at the bottom, followed by the dissolution of IMCs, which leads to a further increase in its growth rate. During solidification stage, the dotted, needle-like and flake θ-FeAl{sub 3} phases were sequentially formed.

36 MATERIALS SCIENCE↗

Solidification dynamics in metal additive manufacturing: analysis of model assumptions

Solidification characteristics in the meltpool drive the process-microstructure relationship which helps dictate the material properties of as-built parts in additive manufacturing; therefore, being able to accurately and quickly simulate the size, shape, and solidification characteristics in the melt pool is of great interest to the field. In this study, we investigate various important physical phenomena (dynamic material properties, fluid-flow, radiation and vaporization) which can either be included or neglected in a continuum finite volume model (FVM) and their effect on the solidification conditions. Additionally, since the simplest form of such a model (conduction only) has an analytic solution which is much faster, its viability is also considered. Since the inclusion of some of these physical phenomena will inherently change the net energy input as well as the amount of energy needed to achieve melting of a control volume, each set of included phenomena had an effective absorption efficiency which was calibrated to closely match the dimensions of the melt pool to that of the ground truth data. The ground truth data for this study was defined to be the output of the FVM which included all the physical phenomena (OF). This study then goes on to compare the effects on solidification conditions each of these calibrated models has. It was found that most of the change in solidification conditions comes from the inclusion of latent heat. A posterior correlation factor (PCF) is then introduced to enable an analytic model to predict similar solidification conditions to OF model.

36 MATERIALS SCIENCE↗

Directional Solidification and Mechanical Properties of NiAl-NiAlTa Alloys

Directional solidification of eutectic alloys is a promising technique for producing in-situ composite materials exhibiting a balance of properties. Consequently, the microstructure, creep strength and fracture toughness of directionally solidified NiAl-NiAlTa alloys were investigated. Directional solidification was performed by containerless processing techniques to minimize alloy contamination. The eutectic composition was found to be NiAl-15.5 at% Ta and well-aligned microstructures were produced at this composition. A near-eutectic alloy of NiAl-14.5Ta was also investigated. Directional solidification of the near-eutectic composition resulted in microstructures consisting of NiAl dendrites surrounded by aligned eutectic regions. The off-eutectic alloy exhibited promising compressive creep strengths compared to other NiAl-based intermetallics, while preliminary testing indicated that the eutectic alloy was competitive with Ni-base single crystal superalloys. The room temperature toughness of these two-phase alloys was similar to that of polycrystalline NiAl even with the presence of the brittle Laves phase NiAlTa.

Johnson, D. R.↗

Cellular-dendritic transition in directionally solidified binary alloys

The microstructural development of binary alloys during directional solidification is studied. Cellular growth data for the Al-Cu and Pb-Sn binary alloy systems are analyzed in order evaluate the criteria of Kurz and Fisher (1981) and Trivedi (1984) for cellular-dendritic transition. It is observed that the experimental growth values do not correlate with the Kurz and Fisher or Trivedi data.

Tewari, S. N.↗

Semiconductors: In Situ Processing of Photovoltaic Devices

Current proposals for developing an extended human presence on the Moon and Mars increasingly consider the processing of nonterrestrial materials essential for keeping the Earth launch burden reasonable. Utilization of in situ resources for construction of lunar and Mars bases will initially require assessment of resource availability followed by the development of economically acceptable and technically feasible extraction processes. In regard to materials processing and fabrication, the lower gravity level on the Moon (0.125 g) and Mars (0.367 g) will dramatically change the presently accepted hierarchy of materials in terms of specific properties, a factor that must be understood and exploited. Furthermore, significant changes are expected in the behavior of liquid materials during processing. In casting, for example, mold filling and associated solidification processes have to be reevaluated. Finally, microstructural development, and therefore material properties, presently being documented through ongoing research in microgravity science and applications, need to be understood and scaled to the reduced gravity environments.

Curreri, Peter A.↗

Effects of an Applied Magnetic Field on the Directional Solidification of Hg(1-x)Zn(x)Se Alloys

Directionally solidified Hg(0.9)Zn(0.1)Se alloys were studied as an alternative to HgCdTe for the detection of electromagnetic radiation because of predicted improvements in lattice stability. Several boules were grown using a modified Bridgman-Stockbarger method and in an applied magnetic field. Axial compositional profiles showed mass transfer was primarily diffusion controlled. Radial compositional variations were greatly reduced when solidification occurred in an applied magnetic field. Microstructural characteristics and dislocation etch pit densities were greatly improved over HgTe based alloys. The extreme importance of processing conditions on defect generation was illustrated by comparing ampoule configurations and thermal profiles.

Cobb, S. D.↗

In-Situ Production of Solar Power Systems for Exploration

Current proposals for developing an extended human presence, beyond space stations, on the Moon and Mars increasingly consider the processing of non-terrestrial materials essential for keeping the Earth launch burden reasonable. Utilization of in-situ resources for construction of lunar and Mars bases will initially require assessment of resource availability followed by the development of economically acceptable and technically feasible extractive processes. In regard to materials processing and fabrication the lower gravity level on the Moon (0.125 g) and Mars (0.367 g) will dramatically change the presently accepted hierarchy of materials in terms of specific properties, a factor which must be understood and exploited. Furthermore, significant changes are expected in the behavior of liquid materials during processing. In casting, for example, mold filling and associated solidification processes have to be reevaluated. Finally microstructural development and therefore material properties, presently being documented through on-going research in microgravity science and applications, needs to be understood and scaled to the reduced gravity environments. One of the most important elements of a human planetary base is power production. Lunar samples and geophysical measurements returned by the Apollo missions provide detailed data on the composition and physical characteristics of the lunar materials and environment. Based on this knowledge and extrapolations of terrestrial industrial experience it is clear that several types of solar-to-electric converters can be manufactured on the Moon. It is conceivable that well over 90% of a solar-to- electric power system could be made from lunar materials. Production and utilization of photovoltaic devices for solar energy production on Earth is primarily driven by the market economy. On Earth a production plant for photovoltaic devices is intimately linked to the planets massive industrial base. A selection of off the shelf refined materials are available as well as cheap fast transportation on demand. The processes takes place (except for the few seconds reprieve in shot towers etc.) under one gravity, with solar radiation significantly modulated by weather, and under conditions where one atmosphere is free and high vacuum is cumbersome and expensive. Off Earth, on lunar or Mars bases, the cost of photovoltaic power is driven by transport costs - Earth launch, deep space transport, landing on the planetary surface. Thus there is a premium for processes that are materials self-sufficient or for closed loop in-situ processes. The lack of differentiated ores on the Moon, and lack of explored minerals on Mars and interplanetary space give a premium to universal/non-ore-specific mineral extractive processes. Initially a semiconductor/photovoltaic production facility will build on no conveniently located industrial base, further increasing the premium on closed loop self sufficient processes.

Curreri, Peter A.↗

In situ Resource Utilization for Processing of Metal Alloys on Lunar and Mars Bases

Current plans for practical missions leading to a sustained human presence on our Moon and Mars rely on utilizing their in situ resources. Initially, resource availability must be assessed followed by the development of economically acceptable and technically feasible extractive processes. In regard to metals processing and fabrication, the lower gravity level on the Moon (0.125 g) and Mars (0.369 g) will dramatically change the presently accepted hierarchy of materials in terms of specific properties, a factor which must be understood and exploited. Furthermore, significant changes are expected in the behavior of liquid metals during processing. In metal casting, for example, mold filling and associated solidification processes have to be reevaluated. Finally, microstructural development and therefore material properties, presently being documented through ongoing research in microgravity science and applications, needs to be understood and scaled to the reduced gravity environments. These and other issues are addressed in this paper.

Stefanescu, D. M.↗

Numerical Research on Magnetic Field, Temperature Field and Flow Field During Melting and Directionally Solidifying TiAl Alloys by Electromagnetic Cold Crucible

The electromagnetic cold crucible (EMCC) technique is an effective method to melt and directionally solidify reactive and high-temperature materials without contamination. The temperature field and fluid flow induced by the electromagnetic field are very important for melting and controlling the microstructure. In this article, a 3D EMCC model for calculating the magnetic field in the charges (TiAl alloys) using the T-Ω finite element method was established and verified. Magnetic fields in the charge under different electrical parameters, positions and dimensions of the charge were calculated and analyzed. The calculated results show that the magnetic field concentrates in the skin layer, and the magnetic flux density (B) increases with increasing of the frequency, charge diameter and current. The maximum B in the charge is affected by the position of the charge in EMCC (h{sub 1}) and the charge height (h{sub 2}), which emerges at the middle of coils (h{sub c}) when the relationship of h{sub c} < h{sub 1} + h{sub 2} < h{sub c} + δ is satisfied. Lower frequency and smaller charge diameter can improve the uniformity of the magnetic field in the charge. Consequently, the induced uniform electromagnetic stirring weakens the turbulence and improves temperature uniformity in the vicinity of the solid/liquid (S/L) interface, which is beneficial to forming a planar S/L interface during directional solidification. Based on the above conclusions, the TiAlNb alloy was successfully melted with lower power consumption and directionally solidified by the square EMCC.

36 MATERIALS SCIENCE↗

Characterization of the Interface of an Alloy 625 Overlay on Steels Using Nanoindentation

Industry standards require postweld heat treatment (PWHT) to reduce the heat-affected zone hardness of steels such as F22 (2.25Cr-1Mo) and AISI 8630 overlaid (clad) with Alloy 625 weld metal. PWHT results in carbon diffusion and accumulation at the interface between the steel and overlay. The accumulation of carbon in a planar solidification growth zone adjacent to the fusion boundary results in high hardness and the potential for hydrogen-assisted cracking. The planar growth zone (PGZ) is so narrow that normal Vickers hardness testing cannot fully reveal the hardness distribution in this zone. This study focused on the application of nanoindentation to characterize the hardness in the narrow microstructural regions adjacent to the fusion boundary. The development of nanohardness maps revealed that the PGZ is not necessarily the region that exhibits peak hardness after PWHT. The highest hardness values were associated with clusters of M{sub 7}C{sub 3} carbides in specific subregions in the PGZ and also in the partially-mixed zone adjacent to the fusion boundary or in steel “swirl” structures. It was also confirmed in this study that nanohardness has a linear correlation with Vickers hardness values. The results presented here provide new insight into the role of carbon diffusion during PWHT and its effect on interface embrittlement associated with Alloy 625 overlays on steel.

36 MATERIALS SCIENCE↗

Influence of Powder Characteristics and Processing Methods on Creep Performance of Powder Metallurgy Hot Isostatic Pressed SS316

The U.S. nuclear energy expansion goals are driving the demand for manufacturing routes that can rapidly produce large, complex, near net shape components. Powder metallurgy hot isostatic pressing (PM HIP) is an advanced manufacturing technique that can be economically scaled-up, while alleviating the supply chain challenges that forging and casting face in terms of cost and lead time constraints. This makes PM-HIP a viable technology to aid and accelerate large-scale part manufacturing for nuclear applications. However, large-scale qualification and deployment of this technology require a thorough understanding of the influence of powder feedstock quality, powder handling history, hot isostatic pressing (HIP) parameters, and subsequent heat treatment on microstructural evolution and elevated temperature mechanical performance. The present work focusses on 316 austenitic stainless steel (SS316) which is most commonly used in high temperature environments for nuclear applications Results from this study show that PM HIPed SS316 meets ASME tensile requirements at room temperature and at elevated temperature. However, creep performance of PM-HIPed SS316 remains inferior to its wrought counterpart, demonstrating that tensile performance alone is not a reliable metric for long duration high temperature integrity. Further, this report delineates powder derived microstructural features that govern creep damage, with key evidences pointing to “microstructural inheritance” from gas atomized powder feedstocks. Commercial SS316 powders of varying chemical compositions and recycling histories were studies, and the results showed large differences in elemental segregation, oxide surface layers and secondary phase distributions. Multi-scale characterization revealed segregation of chromium, molybdenum, manganese and silicon at the boundaries and the precipitation of manganese-, silicon-, and molybdenum-oxides. During HIP consolidation, these surface oxides transform into decorated prior particle boundaries (PPBs) and grain boundary inclusions that persist through conventional post-HIP solution annealing treatment. The retained oxides in post-HIP microstructures were found to influence grain growth, precipitation behavior, and ultimately creep cavitation and fracture. Such post-HIP heat treatments are therefore limited by a complex trade-off between grain growth, and oxide coarsening which aggravate creep damage by acting as nucleation sites for cavities. The objective of this work is to establish an integrated processing–structure–property framework for PM-HIP 316 stainless steel by investigating the influence of powder feedstock characteristics in pre- and post-HIP processing as well as to understand the significance of post-HIP heat treatment on microstructural evolution and creep properties. The results from this report emphasize the significance of powder feedstock integrity in improving creep performance of PM-HIPed SS316, by highlight the effect of rapid solidification, elemental segregation, oxide formation and powder recycling on microstructural defect inheritance following HIP consolidation. Rather than considering HIP processing, solution annealing, and mechanical performance independently, this report treats powder production, HIP consolidation, post-HIP thermal processing, and creep deformation as interconnected stages within a continuous metallurgical process. The resulting framework will provide a scientific basis for developing feedstock engineering strategies capable of improving long-term reliability of PM-HIP stainless steels and accelerating their qualification for advanced nuclear applications.

Ajjarapu, Pavan [Oak Ridge National Laboratory (OR↗

Microstructural development and mechanical properties of a near-eutectic directionally solidified Sn–Bi solder alloy

Sn–Bi solders may be applied for electronic applications where low-temperature soldering is required, i.e., sensitive components, step soldering and soldering LEDs. In spite of their potential to cover such applications, the mechanical response of soldered joints of Sn–Bi alloys in some cases does not meet the strength requirements due to inappropriate resulting microstructures. Hence, careful examination and control of as-soldered microstructures become necessary with a view to pre-programming reliable final properties. The present study aims to investigate the effects of solidification thermal parameters (growth rate — V{sub L} and cooling rate — T-dot{sub L}) on the microstructure of the Sn–52 wt.%Bi solder solidified under unsteady-state conditions. Samples were obtained by upward directional solidification (DS), followed by characterization through metallography and scanning electron microscopy (SEM). The microstructures are shown to be formed by Sn-rich dendrites decorated with Bi precipitates surrounded by a complex regular eutectic mixture, with alternated Bi-rich and Sn-rich phases. Experimental correlations of primary (λ{sub 1}), secondary (λ{sub 2}), tertiary (λ{sub 3}) dendritic and eutectic spacings (λ{sub coarse} and λ{sub fine}) with cooling rate and growth rate are established. Two ranges of lamellar eutectic sizes were determined, described by two experimental equations λ = 1.1 V{sub L}{sup −1/2} and λ = 0.67 V{sub L}{sup −1/2}. The onset of tertiary branches within the dendritic array along the Sn–52 wt.%Bi alloy DS casting is shown to occur for cooling rates lower than 1.5 °C/s. - Highlights: • The Sn–52 wt.%Bi solder was shown to have two eutectic sizes. • The fishbone eutectic is preferably located adjacent to the Bi-rich lamellar phases. • The onset of tertiary dendritic branches in Sn–Bi is associated with T-dot{sub L} < 1.5 °C/s. • Higher eutectic fraction and λ{sub 3} provoked a reverse increase in σ{sub u} and σ{sub y}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗