Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STYRENE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Anion exchange and extraction chromatography tandem column isolation of zirconium-89 ( 89 Zr) from cyclotron bombarded targets using an automated fluidic platform

The long-lived positron emitter 89 Zr is a highly promising nuclide employed in diagnostic Positron Emission Tomography (PET) imaging. Methods of radiochemical processing to obtain 89 Zr for clinical use are traditionally performed with a single hydroxamate resin column. In this work, we present a tandem column purification method for the preparation of high-purity 89 Zr from cyclotron bombarded Y metal foils. The primary column is a macroporous, strongly basic anion exchange resin on styrene divinylbenzene co-polymer. The secondary microcolumn, with an internal volume of 33 µL, is packed with an extraction chromatography resin (ExCR) loaded with HDEHP. A condition of “inverted selectivity” is presented, wherein the 89 Zr elution from the primary column is synonymous with the load condition on the secondary column. The ability to transfer 89 Zr from one column to the next allows two sequential column clean-up methods to be performed prior to the final elution of the 89 Zr product. This approach assures delivery of very high purity 89 Zr . The tandem column purification process has been implemented into a prototype automated fluidic system. Optimization of the method is presented, followed by evaluation of the process using seven cyclotron bombarded Y metal foil targets. Once optimized, we found that 93.7±2.3% of the 89 Zr present in the foils was recovered in the secondary column elution fraction (0.8 M oxalic acid). Radiochromatograms of the product elution peaks enabled determination of full width at half-maximum (FWHM) and 89 Zr collection yields as a function of volume. Because of the small size of the secondary microcolumn, a 89 Zr product volume of ~0.28 mL is reported, which provides a substantially increased nuclide concentration over traditional methods. Finally, we evaluated the transchelation of the resulting 89 Zr oxalate product to deferoxamine mesylate (DFOM) salt. We observed effective specific activities (ESA) and bindable metals concentrations ([M B ]) that exceed those reported by the traditional single hydroxamate column method.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Evaluation of different getter substrates using two-dimensional gas chromatography with time of flight mass spectrometry

We report while understanding hydrogen uptake by organic based getters such as 1,4-bis(phenylethynyl)benzene (DEB) combined with a palladium(0)bis(dibenzylideneacetone) (Pd(dba) 2 ) catalyst is essential, another crucial element to understand is the decomposition of the DEB, Pd(dba) 2 , and/or substrate material. The breakdown of these materials may create unwanted volatiles, which may interact with and lead to deterioration of sensitive materials. Moreover, it is critical to understand if different substrates cause the getter and/or catalyst to degrade in different manners. Utilizing comprehensive two-dimensional gas chromatography (GC×GC) with time-of-flight mass spectrometry (TOFMS), the presence of volatiles located in the headspace of various DEB/Pd(dba) 2 getter substrates is examined. These samples include a getter infused silicone foam, a hydrogenated getter infused silicone foam, an activated carbon getter pellet, and a hydrogenated activated carbon getter pellet. Application of Fisher ratio (F-ratio) analyses lead to the identification of several compounds that are generated or consumed through the hydrogenation process. These include benzene derivatives such as bibenzyl, benzaldehyde, and vinyl benzoate in the activated carbon pellets and 1,5-diphenyl-3-pentanone, toluene, styrene, and 1–1'(2-pentene 1,5-diyl)bis benzene in the silicone foams, and alkane/alkene derivatives such undecane, 4-tridecene, and decane in the activated carbon pellets and 2,6-dimethyl undecane in the silicone foams. Further comparison of the different hydrogenated getter substrates (e.g. activated carbon pellet and silicone foam) indicates that the different substrates alter the decomposition products created from the degradation of the DEB and Pd(dba) 2 .

47 OTHER INSTRUMENTATION↗

An experimental and kinetic modeling study of the pyrolysis of isoprene, a significant biogenic hydrocarbon in naturally occurring vegetation fires

Isoprene dominates the carbon flux emitted by vegetation and constitutes 40% of non-methane biogenic emissions worldwide. Despite pyrolysis experiments at temperatures above 1000 K showing a link between isoprene combustion and aromatic species formation, comprehensive mechanistic research on isoprene is scarce in the literature. Here, in this work, we carry out an experimental and theoretical study to build, for the first time, a chemical kinetic model describing isoprene pyrolysis. The formation of polycyclic aromatic hydrocarbon (PAH) precursor species, often observed in vegetation fire plumes, is partially explained by isoprene pyrolysis experiments and theoretical modeling. Molecular dynamics (MD) simulations unveil reaction pathways from allylic isoprenyl radicals to allene and cyclopentadiene (CPD) intermediates, two relevant species detected in the experiments. Rate constants for these identified pathways are calculated using variational transition state theory to update the kinetic model, which is validated against single-pulse shock tube (SPST), and jet-stirred reactor (JSR) experimental data in the temperature range of 850–1690 K. The kinetic model presents satisfactory agreement with the SPST experimental data, and a reaction pathway analysis shows that association of propargyl radicals results in benzene formation. The JSR pathway analysis also identifies the prominent reactions for CPD, benzene, styrene, and toluene formation. Our model does not reproduce the CPD experimental profiles, indicating that additional studies are necessary. Overall, our findings advance the understanding of isoprene pyrolysis and its related atmospheric pollutants in naturally occurring vegetation fires where smoldering and oxygen-deficient combustion processes are present.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fiber orientation and porosity in large-format extrusion process: The role of processing parameters

Controlling fiber orientation and porosity in short-fiber thermoplastic composites is important for enhancing mechanical, electrical and thermal properties in large-format additive manufacturing. This study employs a factorial design of experiments (DoE) to assess the effects of nozzle diameter (5.08 mm–10.16 mm), temperature (230–250 °C), and extruder screw speed (150–280 rpm) on flow rate, shear rate, porosity, fiber orientation, fiber length and tensile strength in 20 % carbon fiber-filled acrylonitrile butadiene styrene. ANOVA results show that screw speed significantly impacts flow rate, while nozzle diameter and temperature have lesser effects. Shear rate increases with smaller nozzles and higher speeds. Porosity decreases from 5.58 % with a 10.16 mm nozzle to 3.11 % with a 5.08 mm nozzle at 150 rpm due to increased shear rates, which induce shear thinning, reducing viscosity and facilitating gas escape. Larger nozzles (10.16 mm) produce larger, more heterogeneous pores, while smaller nozzles (5.08 mm) yield smaller, uniform pores. Beads produced with the 5.08 mm nozzle exhibit longer fiber lengths due to reduced residence time, lower shear stress, and better alignment. Fiber orientation improves with smaller nozzles due to higher shear rates but decreases with higher screw speeds (280 rpm) due to shorter residence times. The highest fiber alignment (A xx ∼ 0.65) and low porosity (∼3%) were achieved with a 5.08 mm nozzle at 150 rpm, while equivalent additive manufacturing-compression molding samples exhibited better tensile strength (∼93 MPa) under these conditions. In conclusion, these findings emphasize the importance of optimizing processing parameters to enhance fiber alignment and reduce porosity for improved mechanical performance.

Design of experiments↗

Recycling of CF-ABS machining waste for large format additive manufacturing

Large format additive manufacturing (LFAM) necessitates the use of short fiber thermoplastic composites, such as carbon fiber filled acrylonitrile butadiene styrene, to enable printing. Currently, when LFAM parts are machined into their final shape, the machining scrap (i.e., small flake like particles and offcuts) is landfilled. Previous studies have demonstrated the viability of recycling end-of-life LFAM parts by shredding and optionally re-compounding the material back into pellets. However, there is little understanding of the value and performance of recycled material made from LFAM machining scrap, which if pursued could motivate more broad recycling of this waste stream. In this study, recycled in-process machining scrap is explored as an LFAM feedstock source. Herein, it is found that the primary degradation mechanism of the recycled material is significant fiber length attrition during surface machining. While this fiber attrition negatively impacts the mechanical performance of the material in the print direction, it seems that the changes in processing behaviors and print quality, namely the surface roughness of the printed structure associated with shorter fiber lengths, is beneficial to interlayer adhesion. The tensile strength and elastic modulus of the recycled material, in the print direction, decreased 11% and 31% respectively compared to the pristine material. However, in the layer-wise direction it was found that the recycled material exhibited no significant change in elastic modulus and a significant 21% increase in tensile strength – a surprising result. In conclusion, this work indicates that machining waste could be a viable material stream for recycled LFAM feedstock materials.

42 ENGINEERING↗

Macro-level mechanical interlocking: A rapid joining approach for additively manufactured compression molded composite panels

Composite joining typically involves multiple steps, such as drilling and surface treatment, as part of the manufacturing process, which leads to low throughput and long cycle times. In the present study, we demonstrated a macro-level mechanical interlocking (MI) based, rapid joining technique to assemble additively manufactured compression molded (AMCM) panels, enabling the production of parts larger than the mold dimensions. Composite panels made of 20 wt% short carbon fiber reinforced acrylonitrile butadiene styrene (CF/ABS) were joined using MI features of various geometries, namely tree (TR), dovetail (Dov), rectangle 2 (Rect2), and rectangle 1 (Rect1), and their in-plane strength was evaluated. The resultant strength of the tested MI joints reached up to 74 % of the baseline tensile strength (i.e., the ‘no joint’ case). Observations from optical and scanning electron microscopy revealed inadequate polymer diffusion between the adherends, indicating that the joint strength was primarily derived from mechanical interlocking. Additionally, the fracture surfaces exhibited stress-whitening marks, which were characterized using differential scanning calorimetry (DSC). The increase in melting enthalpy suggested local stretching of polymer chains due to MI. Finite element analysis (FEA) indicated that the Rect1 MI feature, which generated the lowest stress concentration, outperformed the others in terms of joint strength, achieving 42 MPa. As a demonstration of the MI joining method, a battery box tray measuring 108 cm × 34 cm using a mold with an effective dimension of 36 cm × 34 cm successfully manufactured, resulting in a part with an area three times larger than the mold. In conclusion, this study presents a promising approach to improving composite joining techniques while minimizing production complexities.

In-plane joining↗

Benchmarking image processing techniques for porosity measurement in polymer additive manufacturing: Review and experimental analysis

An image processing workflow is proposed for porosity measurement in polymer additive manufacturing. Various techniques, including global and local thresholding, region growing, and K-means clustering, were applied to microscopic images of carbon fiber reinforced acrylonitrile butadiene styrene (CF-ABS) and benchmarked for their ability to accurately measure porosity. Global methods included Otsu, minimum error, iterative, and entropy-based thresholding, while local methods included Niblack, Bernsen, Sauvola, and Bradley-Roth algorithms. Artificial uneven illumination was introduced to test local adaptive thresholds. Results showed significant differences in porosity values across methods. Otsu, region growing, and K-means clustering excelled under uniform illumination, while Sauvola and Bradley-Roth performed better with uneven illumination. Comparison with X-ray computed tomography (XCT) revealed slightly lower porosity values (2.55 %) than optimized methods (2.73–2.79 %) due to XCT's lower resolution excluding smaller pores. While XCT offers finer pore detection, it limits sample volume and underestimates porosity due to spatial variation. Validation using artificial grayscale images with 5 % porosity confirmed that Otsu, Bradley-Roth, region growing, and Sauvola algorithms produced accurate results. Although tested on a single material system, these methods can be adapted to others with optimization. In conclusion, given XCT's high computational and time costs, this study highlights suitable image processing techniques as cost-effective alternatives for porosity analysis in polymer composites.

Additive manufacturing↗

Engineering mechanical and thermomechanical performance in additive manufacturing–Compression molded composites through multiplexed extrusion

Traditional extrusion-based additive manufacturing is limited to single material systems, restricting the multifunctional properties of composites. For this work to overcome this limitation, multiplexed additive manufacturing–compression molding (AM-CM) was employed to fabricate multi-material thermoplastic composites with spatially tailored architectures. Neat acrylonitrile butadiene styrene (ABS) and 20 wt% carbon-fiber reinforced ABS (CF-ABS) were co-extruded through a core–sheath nozzle to produce hybrid composites with neat ABS as sheath (30-50 wt%) and CF-ABS as core (50 – 70 wt%). The results show that the hybrid composites have balance of mechanical and thermomechanical performance. The tensile strength and modulus of hybrid composites exhibited a 61–95% and 173–473% increase compared to neat ABS with increases in CF-ABS content whereas the impact resistance improved by 41% compared to CF-ABS at 50 wt% ABS. Additionally, hybrid composites showed significant reduction (54 - 70%) in creep strain at 100 °C compared to neat ABS. These findings demonstrate that multiplexed AM-CM enables tunable structure–property relationships, reducing CF-ABS usage up to 50 wt% while maintaining balanced stiffness, toughness, and creep resistance.

Additive manufacturing↗

Highly oriented carbon fiber–polymer composites via additive manufacturing

Additive manufacturing, diverging from traditional manufacturing techniques, such as casting and machining materials, can handle complex shapes with great design flexibility without the typical waste. Although this technique has been mainly used for rapid prototyping, interest is growing in using this method to directly manufacture actual parts of complex shape. To use 3D-printing additive manufacturing in wide spread applications, the technique and the feedstock materials require improvements to meet the mechanical requirements of load-bearing components. Thus, we investigated the short fiber (0.2 mm to 0.4 mm) reinforced acrylonitrile-butadiene-styrene composites as a feedstock for 3D-printing in terms of their processibility, microstructure and mechanical performance; and also provided comparison with traditional compression molded composites. The tensile strength and modulus of 3D-printed samples increased ~115% and ~700%, respectively. 3D-printer yielded samples with very high fiber orientation in printing direction (up to 91.5 %), whereas, compression molding process yielded samples with significantly less fiber orientation. Microstructure-mechanical property relationships revealed that although the relatively high porosity is observed in the 3D-printed composites as compared to those produced by the conventional compression molding technique, they both exhibited comparable tensile strength and modulus. Furthermore, this phenomena is explained based on the changes in fiber orientation, dispersion and void formation.

36 MATERIALS SCIENCE↗

Characterization of residual stress and deformation in additively manufactured ABS polymer and composite specimens

Residual stresses induced in the layer-by-layer fabrication process of additively manufactured parts have significant impact on their mechanical properties and dimensional accuracy. This work aims here to characterize the residual stress and deformation in specimens based on unreinforced acrylonitrile-butadiene-styrene (ABS), carbon nanotube reinforced ABS and short carbon fiber reinforced ABS. The shrinkage and displacement fields were obtained, respectively, by thermal treatment as well as Digital Image Correlation observation of specimens before and after sectioning. The microstructure and porosity of additively manufactured specimens were also examined using X-ray micro-computed tomography. Specimen shrinkage and porosity content were significantly influenced by the process parameters of raster angle and printing speed, as well as material types. Faster printing speed led to larger porosity and residual stress, as well as higher shrinkage after specimen thermal treatment. Raster angle had a greater influence on specimen shrinkage and porosity as comparing to printing speed. Composite printing wires based on carbon nanotube and short carbon fiber in ABS greatly reduced specimen shrinkage and deformation, while increased the porosity, especially for carbon fiber reinforced ABS specimens.

36 MATERIALS SCIENCE↗

Internal arcing and lightning strike damage in short carbon fiber reinforced thermoplastic composites

Short carbon fiber reinforced thermoplastic composites (S-CFRTP) are currently used in interior parts of aircraft such as electronic circuitry and assemblies, and their usage in aircraft's exterior is also being studied. In this paper, we present a lightning strike study on S-CFRTPs. High performance thermoplastics such as a polyphenylene sulfide (PPS) reinforced with 50% weight (wt.) short carbon fiber (CF), a polyphenyl sulfone (PPSU) reinforced with 25 % wt. Short CF and a acrylonitrile butadiene styrene (ABS) with 20 % wt. short CF were tested against artificial lightning strikes. All samples were prepared using an extrusion compression molding (ECM) technique. A modified component A (100 kA) of lightning waveform, as defined by SAE ARP 5412-B, was applied. High speed imaging, thermography, scanning electron microscopy (SEM) and ultrasonic non-destructive evaluation were performed to understand the effect of lightning strikes on the thermoplastic panels. The results show that electrical conductivity of the composite, thermal stability of the polymers, and CF orientation significantly affected the damage from artificial lightning strikes. PPS composite had the highest resilience against lightning strike damage, retaining 95% and 89% residual flexural strength and modulus, respectively. CF exfoliation due to internal arcing was observed in the carbon fiber-reinforced ABS polymer (CF-ABS) composite. CF exfoliation damage has been reported for the first time.

36 MATERIALS SCIENCE↗

Crashworthiness of recycled carbon fiber composite sinusoidal structures at dynamic rates

Fiber reinforced polymer composites are finding applications in the automotive space for structurally critical applications including crash management. The use of recycled carbon fiber reinforcement can greatly reduce carbon emissions. In this study, recycled carbon fiber composites were manufactured into a self-supporting geometry using three matrices: polyphenylene sulfide (PPS), acrylonitrile butadiene styrene (ABS), and a structural epoxy, and subsequently crushed between flat platens at dynamic rates ranging from 4.6 to 9.1 ms -1 at temperatures in a range of -40°C to 80°C. Load-displacement data was used to evaluate their specific energy absorption, crush efficiency, and steady-state crush stress. Further, the energy absorption of the ABS composites was strongly sensitive to temperature, while the PPS composites exhibited strong crush efficiency dependence with both rate and temperature. The epoxy composites exhibited stable crush behavior at dynamic crush rates but exhibited a dramatic reduction in crush efficiency relative to quasi-static tests. The results of this study indicate that recycled fiber composites can achieve very high energy absorption levels (50–80kJkg -1 at room temperature) that make them an excellent alternative to more expensive and less environmentally friendly continuous virgin fiber laminates.

42 ENGINEERING↗

Performance assessment of 3D printed multi-material energy absorber for automotive bumper: pedestrian lower extremity protection

Designing an energy absorber for automotive bumpers involves balancing low-speed and high-speed impacts to ensure safety, reduce repair costs, and meet regulatory standards. Here, this study explores a novel design using multi-material 3D printing and structural optimization to fabricate a lightweight and cost-efficient energy absorber. The design effectively dissipates energy in low-speed collisions and minimizes force transmission in high-speed pedestrain impacts, helping to meet both safety and performance requirements. The energy absorber design combines 20% carbon fiber-reinforced acrylonitrile butadiene styrene (CF-ABS) and thermoplastic polyurethane (TPU) for optimal stiffness and flexibility. It uses 3D-printed lattice structures optimized through finite element simulations to help meet both low-speed and high-speed impact requirements. Full-scale energy absorbers were 3D-printed using optimized CF-ABS/TPU blends and tested under high-speed impact using the Flexible Pedestrian Legform Impactor (Flex-PLI). For fair comparison, a baseline bumper with a traditional triangular lattice structure, also 3D-printed from the same CF-ABS/TPU materials, was similarly tested. Interestingly, both the optimized and baseline 3D-printed energy absorbers showed nearly identical performance, successfully meeting injury limits. Their performances were also benchmarked against an injection-molded energy absorber. While both 3D-printed and injection-molded designs met injury limits, the 3D-printed absorber exhibited a higher tibia bending moment, indicating an opportunity for further optimization. A Techno-Economic Analysis compared the costs of producing energy absorbers using traditional manufacturing and 3D printing. The analysis highlighted that 3D printing offers cost benefits for low to medium production volumes, with the total cost per energy absorber at ∼ $\$$74, compared to traditional methods that become economical beyond 2000 units.

Additive manufacturing↗

Energy and environmental consequences of a cool pavement campaign

Raising the albedo (solar reflectance) of streets can lower outside air temperature, reduce building energy use, and improve air quality in cities. However, the production and installation of pavement maintenance and rehabilitation treatments with enhanced albedo (“cool” pavements) may entail more or less energy consumption and carbon emission than that of less-reflective treatments. We developed several case studies in which a cool surface treatment is substituted for a more typical treatment (that is, a cool technology is selected instead of a more typical technology). We then assessed over a 50-year analysis period the changes in primary energy demand (PED, excluding feedstock energy) and global warming potential (GWP, meaning carbon dioxide equivalent) in Los Angeles and Fresno, California. The analysis considers two stages of the pavement life cycle: materials and construction (MAC), comprising material production, transport, and construction; and use, scoped as the influence of pavement albedo on cooling, heating, and lighting energy consumption in buildings. In Los Angeles, substituting a styrene acrylate reflective coating or a chip seal for a slurry seal in routine maintenance, or a bonded concrete overlay on asphalt (BCOA) without supplementary cementitious materials (SCM) for mill-and-fill asphalt concrete in conventional or long-life rehabilitation, induced MAC-stage PED and GWP penalties that substantially exceeded use-stage savings, primarily due to material production. Modified rehabilitation cases in which SCM comprised 21% to 50% of the BCOA's total cementitious content by mass (portland cement + SCM) yielded smaller total (MAC + use) PED and GWP penalties, or even total PED and GWP savings. Trends in Fresno were similar, with some differences in GWP outcomes that result from Fresno's longer heating season. The modified rehabilitation cases using BCOA with high SCM content yielded total GWP savings in each city; all other cases yielded total GWP penalties. Here, the magnitude of the one-time GWP offset offered by global cooling from the increased albedo itself always, and sometimes greatly, exceeded the 50-year total GWP penalty or savings. In Los Angeles, the annual building conditioning (cooling + heating) PED and energy cost savings intensities yielded by cool pavements were each about an order of magnitude smaller than the corresponding savings from cool roofs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Constructing a multi-functional polymer network for ultra-stable and safe Li-metal batteries

We report the practical application of lithium (Li) metal electrodes is impeded by Li dendrite growth and unstable solid electrolyte interphase (SEI). Herein, a multi-grafting polymer network, poly(dimethyl siloxane)-g-[poly(poly(ethylene glycol) methyl ether methacrylate)-r-sodium poly(p-styrene sulfonate)] (PPS), is chemically synthesized from reversible addition-fragmentation chain transfer (RAFT) polymerization. With integrated stretchability, ionic conductivity, and mechanical robustness, it serves a dual role to stabilize the Li electrode. As artificial SEI layer, the PPS enables superior electrochemical performance in half cells, symmetric cells, and full cells (PPS@Li/LiFePO 4 , capacity retention of >70% after 600 cycles). Utilized as solid polymer electrolyte (SPE), the all-solid-state Li/SPE/LiFePO 4 full cell delivers excellent cycling performance with an unprecedented capacity retention of 90% over 1,700 cycles at 0.5 C and 81% over 1,000 cycles at 1.0 C. With high-voltage LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) as cathode, the Li/SPE/NMC811 cell exhibits an initial discharge capacity of 162.2 mAh g -1 with a capacity retention of 72% after 200 cycles. The assembled solid-state Li/SPE/LiFePO4 pouch cell with SPE exhibits stable cycling performance over 200 cycles with a capacity retention of 75% and still operates well even after curling, folding, and cutting, demonstrating great potential for achieving ultra-safe and high energy density batteries.

25 ENERGY STORAGE↗

Enhancing stability of poly(1,3-cyclohexadiene)-based materials by bromination and dehydrobromination

In order to improve their thermal stability, poly(1,3-cyclohexadiene) (PCHD) homopolymer, diblock copolymer of PCHD with styrene (PCHD-b-PS), and crosslinked PCHD membranes were dehydrogenated by addition of bromine to the polymer in solution, followed by dehydrobromination using an isothermal treatment at elevated temperature. The brominated PCHD materials thus obtained were characterized via FT-IR and thermogravimetric analysis (TGA) before and after dehydrobromination. Dehydrobromination was performed inside a TGA instrument, allowing insight into thermal stability of the analytes to be obtained. The dehydrobrominated PCHD samples were characterized using elemental analysis, and it was found the dehydrogenation of PCHD to polyphenylene was not complete. Nevertheless, some aromatization did occur, and the thermal stability of the treated polymer was greatly enhanced as compared to its PCHD precursor. Such materials may thus be of interest as high carbon content, graphene-like films. Crosslinked PCHD membranes and PCHD-b-PS diblock copolymers were treated via the same bromination/pyrolysis process, which resulted in markedly improved thermal stabilities for these materials as well.

bromination↗

Ordering of lamellar block copolymers on oxidized silane coatings

Thin films of lamellar poly(styrene-b-methyl methacrylate) (PS-PMMA) block copolymers are widely investigated for surface patterning. These materials can generate dense arrays of nanoscale lines when the lamellar domains are oriented perpendicular to the substrate. To stabilize this preferred domain orientation, we tuned the substrate surface energy using oxidation of hydrophobic silane coatings. This simple approach is effective for a broad range of PS-PMMA film thicknesses when the oxidation time is optimized, which demonstrates that the substrate coating is energetically neutral with respect to PS and PMMA segments. The lamellar films are characterized by high densities of defects that exhibit a strong dependence on film thickness: in-plane topological defects disrupt the lateral order in ultrathin films, while lamellar domains in thick films can bend and tilt to large misorientation angles. As a result, the types and densities of these defects are similar to those observed with other classes of neutral substrate coatings, such as random copolymer brushes, which demonstrates that oxidized silanes can be used to control PS-PMMA self assembly in thin films.

36 MATERIALS SCIENCE↗

Chemical specificity in polyzwitterion-polyelectrolyte coacervates: polycations vs polyanions

Aqueous solutions containing polyzwitterions and polyelectrolytes were studied to probe the effects of chemical specificity on the complexation among different types of chains and resulting liquid–liquid phase separation (coacervation). Two kinds of blends were studied. A polyzwitterion, poly(sulfobetaine methacrylate) (PSBMA), was blended with either (1) a polycation, poly(diallydimethylammonium chloride) (PDADMAC), or (2) a polyanion, sodium poly(styrene sulphonate) (NaPSS). Coacervation was observed in both blends after equilibration, while the freshly prepared blend solutions exhibited distinct behavior dependent on the mixing protocols. Mixing solutions of the polyzwitterions and the polycations led to coacervation almost instantaneously. In contrast, the blends containing the same polyzwitterions and the polyanions exhibited no such coacervation by following the same mixing protocol. However, blends prepared after dissolving a solid mixture containing the same polyzwitterions and the polyanions in water exhibited coacervation. Based on the small-angle X-ray scattering (SAXS), cryo-electron microscopy, and rheology measurements, complexation and coacervation in the polyzwitterion-polyelectrolyte blends is rationalized in terms of the entropy change associated with reorganization of solvent (water), which appears to be larger in the polyzwitterion-polycation case in comparison with the polyzwitterion-polyanion blends. These results highlight the importance of chemical specificity and mixing protocols leading to metastable structures in designing a new class of materials based on macromolecular complexation of polyzwitterions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗