SEARCH · Engineering Papers

Results for “STIMULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

DOE OSTI2023

CO 2 -Responsive Fracturing Fluids for Enhanced Geothermal Systems (Final Report)

Our group has recently developed StimuFrac, a non-toxic stimuli-responsive fracturing fluid consisting of a CO 2 -reactive polymer which has shown at the lab-scale to consistently fracture rock cores at significantly lower net pressures in a range of representative geothermal pressure/temperature conditions. However, until now the mechanism/s responsible for more effective fracturing, of critical importance to optimize fracturing performance as well as strategize injection methodologies for field deployment, was not understood. In this document, we report (1) on the two main mechanisms responsible for fracturing rock at lower net pressures with StimuFrac; (2) the phase behavior of StimuFrac/CO 2 under geothermal wellbore conditions; and (3) based on high-temperature true triaxial stimulations, detailed evidence that StimuFrac/CO 2 is the best performing stimulation fluid under EGS T/P conditions as compared to water, waterless CO 2 , and CO 2 /water fracturing fluids. This is because i) it requires significantly lower volumes of CO 2 due to its reduced leak off into the formation by the crosslinked polymer solution; ii) large fractures can be generated reproducibly at both low and high CO 2 injection flow rates, and iii) the reversible (previously reported) viscosity increase of StimuFrac could be beneficial to transport proppants when they become available for EGS. These results were particularly evident for hot nearly dry rock as well as partially and nearly fully water-saturated granitic rock. GTO requires StimuFrac to be evaluated in fully water-saturated rock to determine whether the above-described performance applies under these conditions. Since (1) GTO considers there is no enough evidence for Sa different StimuFrac formulation to work below 90C (where full water-saturation in an open system is possible) and (2) no polyaxial loading frame larger than a few centimeters that can do hydraulic fracturing tests while maintaining the rock sample fully saturated with water at 200 C exists; PNNL concludes that the only way to determine if StimuFrac represents an advanced fracturing fluid alternative for EGS, is to perform a stimulation in an actual EGS reservoir.

15 GEOTHERMAL ENERGY↗

DOE OSTI2024

Waveguides for neurostimulation in the cochlea

Introduction Optical stimulation has been suggested for neural stimulation to improve cochlear implants. Light allows for more spatially selective activation of neuron populations than electrical current, offering more independent frequency bands along the spiral ganglion. These bands are available to encode acoustic information with anticipated better frequency resolution, improving cochlear implant user performance in noisy listening environments, tonal languages, and music perception. Methods Optical cochlear implants (oCIs) can deliver light either directly via small emitters within the cochlea or via waveguides from external optical sources. We investigated three waveguide designs made from OrmoComp ® , a polymer that cures through ultraviolet (UV) radiation. Waveguides were fabricated via injection molding and coated using dip-coating or thermal reflow, or through aspiration of OrmoComp ® into polyimide tubing that served as the cladding of the waveguide. The choice of fabrication technique directly determined the waveguides' total diameter: thermal reflow yielded ≈940 μm, dip-coating produced ≈306 μm, and aspiration resulted in ≈132 μm core diameter waveguides. Given the human cochlea's small size, we focused on analyzing the 306-μm and 132-μm waveguides, evaluating their optical performance (propagation and bending losses) and mechanical properties (bending stiffness and insertion forces). Furthermore, we evaluated some of these designs in in-vivo guinea pigs experiments. Results For the 100-μm core diameter waveguides, the propagation losses were 12.34 ± 1.26, 1.18 ± 0.88, 1.49 ± 0.58, and 3.43 ± 0.68 dB/cm at 534, 1,375, 1,460, and 1,550 nm, respectively. The respective bending losses at a 2 mm radius of curvature were 5.50 ± 1.32, 0.56 ± 0.26, 0.79 ± 0.18, and 0.64 ± 0.23 dB, and at 1 mm 8.54 ± 1.30, 2.05 ± 0.84, 2.11 ± 0.50, and 1.44 ± 0.37 dB. The bending stiffness of a 1 mm segment of the 100-μm-diameter waveguides was 18.9 ± 2.2 N/m. Insertion forces for the 100-μm-diameter waveguides into an acrylic human-size scala tympani model were < 25 mN. For the waveguides with 306 and 940 μm total diameter, the propagation losses ranged between 0.43 and 2.40 dB/cm at 534, 680, 1,375, and 1,550 nm, between 2.19 and 3.78 dB/cm at 450 and 1,460 nm. Bending losses for 360 degrees at 1,375 nm were 5.0, 2.4, and 0.46 for a bending radius of 2.5-, 3-, and 4-mm. Discussion Our study demonstrated that the polymer OrmoComp ® is suitable for fabricating waveguides to transmit near-infrared radiation. In-vivo experiments showed optically evoked auditory responses originating from optical stimulation in the guinea pigs' first cochlear turn while radiation was delivered. Incoming experiments will focus on evaluating long-term performance of these waveguides in guinea pigs and cats. This study will be designed to provide insights into the waveguides' performance and biocompatibility over extended periods, essential for their potential clinical application in future oCIs.

Kim, Matthew↗

DOE OSTI2022

Induced microearthquakes predict permeability creation in the brittle crust

Predicting the evolution of permeability accurately during stimulation at the reservoir scale and at the resolution of individual fractures is essential to characterize the fluid transport and the reactive/heat-transfer characteristics of reservoirs where stress exerts significant control. Here, we develop a hybrid machine learning (ML) model to visualize in situ permeability evolution for an intermediate-scale (~10 m) hydraulic stimulation experiment. This model includes an ML model that was trained using the well history of flow rate and wellhead pressure and MEQ data from the first three stimulation episodes to predict average permeability from the statistical features of the MEQs alone for later episodes. Moreover, a physics-inspired model is integrated to estimate in situ fracture permeability spatially. This method relates fracture permeability to fracture dilation and scales dilation to the equivalent MEQ magnitude, according to laboratory observations. The seismic data are then applied to define incremental changes in permeability in both space and time. Our results confirm the excellent agreement between the ground truth and model-predicted permeability evolution. The resulting permeability map defines and quantifies flow paths in the reservoir with the averaged permeability comparing favorably with the ground truth of permeability.

induced seismicity↗

DOE OSTI2024

Tetranuclear Polypyridylruthenium(II) Complexes as Selective Nucleic Acid Stains for Flow Cytometric Analysis of Monocytic and Epithelial Lung Carcinoma Large Extracellular Vesicles

Selective staining of extracellular vesicles (EVs) is a major challenge for diagnostic and therapeutic applications. Herein, the EV labeling properties of a new class of tetranuclear polypyridylruthenium(II) complexes, Rubb7-TNL and Rubb7-TL, as phosphorescent stains are described. These new stains have many advantages over standard stains to detect and characterize EVs, including: high specificity for EV staining versus cell staining; high phosphorescence yields; photostability; and a lack of leaching from EVs until incorporation with target cells. As an example of their utility, large EVs released from control (basal) or lipopolysaccharide (LPS)-stimulated THP-1 monocytic leukemia cells were studied as a model of immune system EVs released during bacterial infection. Key findings from EV staining combined with flow cytometry were as follows: (i) LPS-stimulated THP-1 cells generated significantly larger and more numerous large EVs, as compared with those from unstimulated cells; (ii) EVs retained native EV physical properties after staining; and (iii) the new stains selectively differentiated intact large EVs from artificial liposomes, which are models of cell membrane fragments or other lipid-containing debris, as well as distinguished two distinct subpopulations of monocytic EVs within the same experiment, as a result of biochemical differences between unstimulated and LPS-stimulated monocytes. Comparatively, the staining patterns of A549 epithelial lung carcinoma-derived EVs closely resembled those of THP-1 cell line-derived EVs, which highlighted similarities in their selective staining despite their distinct cellular origins. This is consistent with the hypothesis that these new phosphorescent stains target RNA within the EVs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Isolation of Methane Enriched Bacterial Communities and Application as Wheat Biofertilizer under Drought Conditions: An Environmental Contribution

The search for methanotrophs as plant-growth-promoting rhizobacteria (PGPR) presents an important contribution to mitigating the impact of global warming by restoring the natural soil potential for consuming methane while benefiting plants during droughts. Our in silico simulations suggest that water, produced as a byproduct of methane oxidation, can satisfy the cell growth requirement. In addition to water, methanotrophs can produce metabolites that stimulate plant growth. Considering this, we proposed that applying methanotrophs as PGPR can alleviate the effect of droughts on crops, while stimulating atmospheric methane consumption. In this work, we isolated a series of methanotrophic communities from the rhizospheres of different crops, including Italian sweet pepper and zucchini, using an atmosphere enriched with pure methane gas, to determine their potential for alleviating drought stress in wheat plants. Subsequently, 23 strains of nonmethanotrophic bacteria present in the methanotrophic communities were isolated and characterized. We then analyzed the contribution of the methane-consuming consortia to the improvement of plant growth under drought conditions, showing that some communities contributed to increases in the wheat plants’ lengths and weights, with statistically significant differences according to ANOVA models. Furthermore, we found that the presence of methane gas can further stimulate the plant–microbe interactions, resulting in larger plants and higher drought tolerance.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Visualization of a Limonene Synthesis Metabolon Inside Living Bacteria by Hyperspectral SRS Microscopy

Abstract Monitoring biosynthesis activity at single‐cell level is key to metabolic engineering but is still difficult to achieve in a label‐free manner. Using hyperspectral stimulated Raman scattering imaging in the 670–900 cm −1 region, localized limonene synthesis are visualized inside engineered Escherichia coli . The colocalization of limonene and GFP‐fused limonene synthase is confirmed by co‐registered stimulated Raman scattering and two‐photon fluorescence images. The finding suggests a limonene synthesis metabolon with a polar distribution inside the cells. This finding expands the knowledge of de novo limonene biosynthesis in engineered bacteria and highlights the potential of SRS chemical imaging in metabolic engineering research.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Sensory integration for neuroprostheses: from functional benefits to neural correlates

In the field of sensory neuroprostheses, one ultimate goal is for individuals to perceive artificial somatosensory information and use the prosthesis with high complexity that resembles an intact system. To this end, research has shown that stimulation elicited somatosensory information improves prosthesis perception and task performance. While studies strive to achieve sensory integration, a crucial phenomenon that entails naturalistic interaction with the environment, this topic has not been commensurately reviewed. Therefore, here we present a perspective for understanding sensory integration in neuroprostheses. First, we review the engineering aspects and functional outcomes in sensory neuroprosthesis studies. In this context, we summarize studies that have suggested sensory integration. We focus on how they have used stimulation-elicited percepts to maximize and improve the reliability of somatosensory information. Next, we review studies that have suggested multisensory integration. These works have demonstrated that congruent and simultaneous multisensory inputs provided cognitive benefits such that an individual experiences a greater sense of authority over prosthesis movements (i.e., agency) and perceives the prosthesis as part of their own (i.e., ownership). Thereafter, we present the theoretical and neuroscience framework of sensory integration. We investigate how behavioral models and neural recordings have been applied in the context of sensory integration. Sensory integration models developed from intact-limb individuals have led the way to sensory neuroprosthesis studies to demonstrate multisensory integration. Neural recordings have been used to show how multisensory inputs are processed across cortical areas. Lastly, we discuss some ongoing research and challenges in achieving and understanding sensory integration in sensory neuroprostheses. Here, resolving these challenges would help to develop future strategies to improve the sensory feedback of a neuroprosthetic system.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2022

Utilization of the CW magnetrons as coherent RF sources for superconducting RF accelerators

CW magnetrons designed and optimized for industrial heaters, driven by an injection-locking signal, were suggested to power Superconducting RF (SRF) cavities. However, the CW magnetrons, which are regenerative generators, are intended to operate in self-excitation mode, so, for reliable starting they use a large regenerative gain, causing a large regenerative instability in operation. Thus, power supply ripple, even shot noise, etc., lead to multiple sidebands forming a quasi-continuous noise spectrum at the carrier frequency. Therefore, in the traditionally used mode of operation and control, such magnetrons are inapplicable for powering high Q-factor SRF cavities. A new approach to operation and control of CW magnetrons considering non-stationary processes during start-up and operation makes it possible to find a mode of almost coherent RF generation of tubes with a significant reduction in regenerative instability and noise and increased efficiency. In our work is presented substantiation for the newly developed mode with an analysis of the new approach based on experimental results. •In this article, for the first time, non-stationary, regenerative processes are considered during the start-up and operation of CW magnetrons for powering high-Q superconducting RF cavities.•An analytical study, confirmed by experiments, showed that the traditionally used modes of starting and operating CW magnetrons are not suitable for powering high-Q superconducting RF cavities.•In fact, to make CW magnetrons suitable for such cavities, the physics of starting and operating CW magnetrons must be changed. This has been demonstrated in our work.•In developing the Stimulated Coherent Generation Mode [NIM A 980 (2020) 164366], we have shown the suitability of this mode for starting and operating CW magnetrons for high-Q superconducting RF cavities.•Analytical analysis, verified experimentally, substantiates in our article the suitability of the “Mode of stimulated coherent generation” of CW magnetrons for powering high-Q superconducting cavities in pulsed and continuous modes.

43 PARTICLE ACCELERATORS↗

DOE OSTI2021

Substrate stiffness modulates endothelial cell function via the YAP-Dll4-Notch1 pathway

Highlights: • Soft stiffness increases Dll4 expression in endothelial cells via YAP suppression. • Soft substrate-induced Dll4-Notch1 signaling is facilitated by VEGF stimulation. • Elevated Dll4-Notch1 signaling contributes to the regulation of VEGFRs expression. • Substrate stiffness modulates gene expression linked to endothelial cell function. Endothelial cells adapt their functions as a consequence of sensing extracellular substrate stiffness; these alterations allow them to maintain their vascular structure and function. Substrate stiffness-mediated yes-associated protein 1 (YAP) activation plays an important role in mechano-transduction and pro-angiogenic phenotype of endothelial cells, and Delta-like ligand 4 (Dll4)-Notch1 signaling is closely related to angiogenesis; however, the impact of substrate stiffness-mediated interrelation of these pathways on endothelial cell functions remains elusive. We confirmed that endothelial cells on softer substrates not only elongate cellular aspects but also attenuate YAP activation compared to cells on stiffer substrates. Endothelial cells on softer substrates also upregulate the vascular endothelial growth factor receptor 1 (VEGFR1) and VEGFR2 mRNA expression that is enhanced by VEGF stimulation. We determined that endothelial cells on softer substrates increased Dll4 expression, but not Notch1 expression, via YAP signaling. Moreover, endothelial cells on soft substrates induced not only VEGFRs upregulation but also suppression of pro-inflammatory interleukin-6 and plasminogen activator inhibitor-1 mRNA expression and the facilitation of anti-coagulant thrombomodulin and pro-coagulant tissue factor mRNA expression. Our results suggest that endothelial cells activate the YAP-Dll4-Notch signaling pathway in response to substrate stiffness and dictate cellular function.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

Selenomethionine protects oxidative-stress-damaged bone-marrow-derived mesenchymal stem cells via an antioxidant effect and the PTEN/PI3K/AKT pathway

Highlights: • Oxidative stress stimuli by H{sub 2}O{sub 2} suppressed osteogenic differentiation of BMSCs. • Selenomethionine could alleviate osteogenic dysfunction of oxidative-stress-damaged BMSCs. • Selenomethionine rescued osteogenic ability partly through the modulation of the PTEN/PI3K/AKT pathway. Dental implant surgery is currently a routine therapy for the repair of missing dentition or dentition defects. Both clinical and basic research have elucidated that oxidative stress caused by the accumulation of reactive oxygen species (ROS) for various reasons impairs the process of osteointegration after dental implantation. Therefore, the osteogenic micro-environment must be ameliorated to decrease the damage caused by oxidative stress. Selenomethionine (SEMET) has been reported to play an important role in alleviating oxidative stress and accelerating cell viability and growth. However, it remains unclear whether it exerts protective effects on bone-marrow-derived mesenchymal stem cells (BMSCs) under oxidative stress. In this study, we explored the influence of selenomethionine on the viability and osteogenic differentiation of BMSCs under oxidative stress and the underlying mechanisms. Results showed that 1 μM selenomethionine was the optimum concentration for BMSCs under H{sub 2}O{sub 2} stimulation. H{sub 2}O{sub 2}-induced oxidative stress suppressed the viability and osteogenic differentiation of BMSCs, manifested by the increases in ROS production and cell apoptosis rates, and by the decrease of osteogenic differentiation-related markers. Notably, the aforementioned oxidative damage and osteogenic dysfunction induced by H{sub 2}O{sub 2} were rescued by selenomethionine. Furthermore, we found that the PTEN expression level was suppressed and its downstream PI3K/AKT pathway was activated by selenomethionine. However, when PTEN was stimulated, the PI3K/AKT pathway was down-regulated, and the protective effects of selenomethionine on BMSC osteogenic differentiation diminished, while the inhibition of PTEN up-regulated the protective effects of selenomethionine. Together, these results revealed that selenomethionine could attenuate H{sub 2}O{sub 2}-induced BMSC dysfunction through an antioxidant effect, modulated via the PTEN/PI3K/AKT pathway, suggesting that selenomethionine is a promising antioxidant candidate for reducing oxidative stress during the process of dental implant osteointegration.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2020

Optical fields in porous polylactide matrices

Optical fields induced by laser light inside porous polymer matrices (scaffolds) under stimulating effect on cells are investigated. The spectra of light scattering coefficients and anisotropy factors of porous polylactide scaffolds in the visible and near-IR ranges are determined by numerical simulation based on experimental data obtained using a double integrating sphere. Studies are conducted for dry and wet scaffolds fabricated by supercritical fluid foaming and surface-selective laser sintering. The Monte Carlo method is used to calculate the fluence rate distribution under the assumptions of the Henyey – Greenstein phase scattering function and the model phase function of scattering on spherical cavities. It is shown that th e fluence rate distribution mainly depends on the scattering coefficient and the mean cosine of the deflection angle (g-factor). The results obtained are of great practical importance for tissue engineering based on the use of polymeric porous scaffolds with cells to replace tissue defects; they can be used to determine the dose range for laser stimulation of cells. (paper)

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2022

Generation of intense phase-stable femtosecond hard X-ray pulse pairs

Significance The generation of phase-stable femtosecond X-ray pulse pairs will advance nonlinear spectroscopies and imaging, providing direct insight into the coupled motions of electrons and nuclei with resolution on the electronic length scale and timescale. This paper presents the generation of such pulse pairs in the X-ray domain. The approach uses X-ray free-electron laser pulses to induce highly directional, intense, phase-stable pairs of superfluorescence and seeded stimulated emission at the 5.9 keV manganese Kα 1 line. The finding is evidenced by strong interference fringes in the superfluorescence and stimulated emission signals.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

Uncovering microstructure and composition susceptibility of high permittivity ceramic granules to plasma-induced arc breakdown

Effective diversion of surge currents is vital to prevent unwanted damage to sensitive electronics. Among the most successful and efficient strategies relies on a dielectric stimulated arc breakdown mechanism with high permittivity ceramic granules in a spark-gap geometry. Although generally regarded as a self-healing process, substantial energy deposition may occur that, over time, diminishes the ability to withstand repeated electrical assaults. We investigate the susceptibility of lead–magnesium–niobate–lead titanate (PMN–PT) granule microstructure and composition changes following many exposures to high voltage impulses resulting in arc breakdown. Scanning electron microscopy and energy-dispersive spectroscopy mapping reveal a broad range of thermal and mechanical defects entailing thermal reduction of constituent PMN–PT metal ions and recasting due to rapid eruption of volatile species. Additionally, evidence of local melting and microcracking are apparent that can have deleterious impact on the proper function of the granules, namely, the ability to concentrate electric fields across air gaps to establish and sustain discharge pathways. We propose that the localized nature of damage and stochasticity associated with the dielectric stimulated breakdown mechanism may allow granules to maintain functionality provided no permanent conduction paths are established.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Utah FORGE: Discrete Fracture Network (DFN) Data

The FORGE team is making these fracture models available to researchers wanting a set of natural fractures in the FORGE reservoir for use in their own modeling work. They have been used to predict stimulation distances during hydraulic stimulation at the open toe section of well 16A(78)-32. These fracture sets are fully stochastic and do not contain the deterministic set that matches the pilot well 58-32 FMI data. Well 58-32 has been completed and 16A(78)-32 is to be drilled as part of Phase 3. The original .fab files are not included due to redundancy. The *.fabgz data for the 800m and 1200m depth areas are in the native FracMan format and have been compressed using Gzip. Filtered data for the 800m depth area includes .csv spreadsheets, native FracMan (.fab), and GOCAD (.ts) files that are in a compressed zip format. The file titled "SGW 2020 Finnila and Podgorney DFN fracture files on GDR.pdf" is a description of the data and should be reviewed prior to data use.

15 GEOTHERMAL ENERGY↗

DOE OSTI2021

Utah FORGE Well 16A(78)-32 Simplified Discrete Fracture Network Data

15 GEOTHERMAL ENERGY↗

DOE OSTI2024

Utah FORGE 10-3726: Geothermal Multiset Straddle for High Temperature Applications - 2024 Annual Workshop Presentation

This is a presentation on the Geothermal Multiset Straddle (GMS) for High Temperature Applications by Welltec, presented by Ricardo Vasques. This video slide presentation discusses the development of (1) an annular multiset isolation system; (2) a stimulation straddle isolation system; and (3) a multi open-close flow system, for geothermal environments. This is to enable effective zonal isolation and stimulation with multiset capabilities, to implement downhole controlled EGS in any location, and to extend the productive life of the well. This presentation was featured in the Utah FORGE R&D Annual Workshop on August 15, 2024.

15 GEOTHERMAL ENERGY↗

DOE OSTI2026

Improving Production in the Emerging Paradox Oil Play (Final Technical Report)

This report documents the results of the DOE-funded project Improving Production in the Emerging Paradox Oil Play, focused on integrating geological characterization, petrophysical analysis, reservoir simulation, and field development planning to improve hydrocarbon recovery from the Paradox Basin. Project activities included core and log analysis, assessment of reservoir heterogeneity and compartmentalization, evaluation of completion and stimulation strategies, and development of an uncertainty-aware field development framework. Findings highlight the importance of selective completions, geology-driven well placement, and targeted stimulation in vertically heterogeneous carbonate reservoirs.

02 PETROLEUM↗

DOE OSTI2024

Trap‐Engineering the Persistent Luminescence of Ca 3 Ga 4 O 9 :Tb 3+ via Al 3+ Substitution for Optical Data Storage

Abstract Optically stimulated luminescence (OSL) materials hold great potential for optical data storage (ODS) and anticounterfeiting applications. Nevertheless, the scarcity of suitable luminescent materials with deep‐level traps remains a significant obstacle. Herein, a host substation strategy have been employed to tune the persistent luminescence (PersL) and OSL properties of Ca 3 Ga 4 O 9 :Tb 3+ by Al 3+ substitution through trap engineering and demonstrated their potential. Specifically, the photoluminescence of the Ca 2.985 (Ga 1‐y% Al y% ) 4 O 9 :0.5%Tb 3+ of Tb 3+ is first investigated due to its different occupancies of Ca 2+ . The influence of host substitution on the crystal structure, trap depth, trap density, PersL, and OSL properties have further investigated. A series of strong PersL and OSL peaks from the Ca 2.985 (Ga 1‐y% Al y% ) 4 O 9 :0.5%Tb 3+ with bluish‐green emissions have been observed. The Ca 2.985 (Ga 1‐y% Al y% ) 4 O 9 :0.5%Tb 3+ have shown controllable photon release upon thermal and optical stimuli, enhancing their performance for ODS. Thermally stimulated luminescence suggests that vacancy and defect concentrations inside the Ca 3‐x% (Ga 1‐y% Al y% ) 4 O 9 :x%Tb 3+ can be manipulated by Tb 3+ doping and Al 3+ substitution, which ultimately leads to the formation of deep traps and a broad distribution of traps with increased deep trap concentration. The work demonstrates that trap engineering through Al 3 ⁺ substitution is an effective method for tuning PersL and OSL properties of Ca 2.985 (Ga 1‐y% Al y% ) 4 O 9 :0.5%Tb 3+ for ODS.

Abeywickrama, Thulitha M. [Department of Chemistry↗