Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Performance of U 3 Si 2 in an LWR following a cladding breach during normal operation

High-density fuels have been proposed as a possible replacement for uranium-dioxide as a fuel for light water reactors (LWRs) due to their increased loading of fissionable material. The objectives of this proposal are (1) to increase reactor cycle length and reactor power, and (2) to offset any neutronic penalty associated with advanced cladding systems. Of the high-density fuels under consideration, there is particular interest in triuranium disilicide (U 3 Si 2 ) due to its increased metal density and favorable thermal properties as compared to UO 2 . However, there are concerns regarding the chemical compatibility of U 3 Si 2 with water and steam as used for LWR coolant.This paper summarizes research on fuel-coolant chemical compatibility for UO 2 LWR fuel during a cladding breach and highlights that generally, because of its chemical inertness, UO 2 -coolant reactions are of little consequence to reactor operation. However, the volumetric expansion associated with the reaction of UO 2 and oxygen is a concern for possible conditions encountered during air ingress of dry storage. These same concerns arise for U 3 Si 2 , which exhibits greater volumetric expansion than UO 2 when exposed to water or steam. These reactions ultimately result in increased fuel volume that the cladding must accommodate, as well as additional heat generated as the fuel reacts.The BISON fuel performance code was used to perform a comparative analysis on the behavior of UO 2 and U 3 Si 2 under normal operation. Silicide fuel simulations were then extended to demonstrate how varying thermodynamic and chemical kinetics influence fuel expansion and subsequent cladding performance during a cladding breach. These simulations were further extended to a 3D subsection of a fuel rod to demonstrate the characteristics of the resulting cladding crack.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Crystal structure and electronic properties of the new compounds U{sub 3}Co{sub 12-x}X{sub 4} with X=Si, Ge

The new compounds U{sub 3}Co{sub 12-x}X{sub 4} with X=Si, Ge were prepared by direct solidification of the corresponding liquid phase, followed by subsequent annealing at 1173 K. Single crystal X-ray diffraction carried out at room temperature showed that they crystallize with the hexagonal space group P6{sub 3}/mmc (no.194) and the unit-cell parameters a=8.130(5), c=8.537(5) A and a=8.256(1), c=8.608(1) A for the silicide and germanide, respectively. Their crystal structure derives from the EuMg{sub 5.2} structure type, and is closely related to the Sc{sub 3}Ni{sub 11}Si{sub 4} and Gd{sub 3}Ru{sub 4-x}Al{sub 12+x} types. For the present compounds, no substitution mechanisms have been observed, the partial occupancy of one Co site results from the presence of vacancies, only. The homogeneity ranges, evaluated by energy dispersive spectroscopy analysis, extend from x=0.0(2) to 0.3(2) and from x=0.0(2) to 1.0(2) for U{sub 3}Co{sub 12-x}Si{sub 4} and U{sub 3}Co{sub 12-x}Ge{sub 4}, respectively. The electronic properties of both compounds were investigated by means of DC magnetic susceptibility and DC electrical resistivity measurements. The U{sub 3}Co{sub 12-x}X{sub 4} compounds are both Pauli paramagnets with their electrical resistivity best described as poor metallic or dirty metallic behavior. - Graphical abstract: The crystal structure of the new compounds U{sub 3}Co{sub 12-x}X{sub 4}, X=Si, Ge is a ternary ordered variant of the EuMg{sub 5.2}-type with a site preference for the 4e position.

36 MATERIALS SCIENCE↗

Microwaved assisted fast synthesis of n and p-doped Mg{sub 2}Si

Magnesium silicide based alloys fast syntheses have been carried out using microwave heating. Precursors were first ball milled powders together under inert gas. Resulting powders were then placed into a glassy carbon crucible before being heated by microwave irradiation. Sintering of the powder was performed by spark plasma method. XRD and SEM/EDS were used to investigate composition, structure and morphology. Thermoelectric performances of the samples were measured in the temperature range of 320–775 K. The doping effect of several elements such as silver, tin, antimony, cobalt and bismuth has been studied. n-Type and p-type Mg{sub 2}Si based materials have been successfully synthesized, with maximum ZT value up to 0.7 and 0.35 at 770 K for a n-type and a p-type sample, respectively. We demonstrate here that the use of microwave irradiation to prepare doped Mg{sub 2}Si is possible, and we discuss here the thermoelectric properties of such samples. - Schematic representation of microwave hybrid heating. - Highlights: • A promising method for fast production of Mg{sub 2}Si in the frame of heat harvesting applications is presented. • A novel technological approaches towards nanostructured materials is proposed. • Thermoelectric properties of Mg{sub 2}Si doped materials prepared under microwave irradiation are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A simple facile approach to large scale synthesis of high specific surface area silicon nanoparticles

An inexpensive, facile, and high throughput synthesis of silicon nanoparticles was achieved by the mechano-chemical reduction reaction of magnesium silicide (Mg{sub 2}Si) and silicon monoxide (SiO) using a high energy mechanical milling (HEMM) technique followed by acid leaching. Characterization of the resultant product using X-Ray diffraction, Raman spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and surface area analyses was performed at various stages of the synthesis process. XRD patterns show that the final product formed is single phase silicon and the nanocrystalline nature was confirmed by the shifted transverse optical (TO) band, characteristic of nc-Si determined by Raman analysis. SEM and TEM shows the presence of particles of different sizes in the range of few nanometers to agglomerates of few microns which is consistent with products obtained from mechanical milling. BET measurements show a very high specific surface area (SSA) of ∼190 m{sup 2}/g obtained due to acid leaching which is also validated by the porous nature of the particles confirmed by the SEM images. - Graphical abstract: Schematic showing the large scale production of nanosized silicon and BET surface area of the product formed at various stages.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microwave sintering of MoSi{sub 2}-Mo{sub 5}Si{sub 3} to promote a final nanometer-scale microstructure and suppressing of pesting phenomenon

This work shows an innovative sintering process for molybdenum disilicide (MoSi{sub 2}) and molybdenum silicide (Mo{sub 5}Si{sub 3}) in order to have a final nanometer-scale microstructure. Sintered MoSi{sub 2}-Mo{sub 5}Si{sub 3} was fabricated by microwave sintering. The final material showed a significant reduction of pesting phenomena for MoSi{sub 2}. The final microstructure is a mix of micrometer-scale MoSi{sub 2} and nanometer-scale Mo{sub 5}Si{sub 3} immersed in an amorphous SiO{sub 2} phase. This material was characterized by X-Ray diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and Thermal Gravimetric Analysis (TGA). - Highlights: Black-Right-Pointing-Pointer We sintered the MoSi{sub 2}-Mo{sub 5}Si{sub 3} by microwave and obtained high final density material. Black-Right-Pointing-Pointer We got a final nanostructured material. Black-Right-Pointing-Pointer We inhibited pesting phenomenon for MoSi{sub 2}.

36 MATERIALS SCIENCE↗

Microstructural evolution during transient liquid phase bonding of Inconel 738LC using AMS 4777 filler alloy

IN-738LC nickel-based superalloy was joined by transient liquid phase diffusion bonding using AMS 4777 filler alloy. The bonding process was carried out at 1050 Degree-Sign C under vacuum atmosphere for various hold times. Microstructures of the joints were studied by optical and scanning electron microscopy. Continuous centerline eutectic phases, characterized as nickel-rich boride, chromium-rich boride and nickel-rich silicide were observed at the bonds with incomplete isothermal solidification. In addition to the centerline eutectic products, precipitation of boron-rich particles was observed in the diffusion affected zone. The results showed that, as the bonding time was increased to 75 min, the width of the eutectic zone was completely removed and the joint was isothermally solidified. Homogenization of isothermally solidified joints at 1120 Degree-Sign C for 300 min resulted in the elimination of intermetallic phases formed at the diffusion affected zone and the formation of significant {gamma} Prime precipitates in the joint region. - Highlights: Black-Right-Pointing-Pointer TLP bonding of IN-738LC superalloy was performed using AMS 4777 filler alloy. Black-Right-Pointing-Pointer Insufficient diffusion time resulted in the formation of eutectic product. Black-Right-Pointing-Pointer Precipitation of B-rich particles was observed within the DAZ. Black-Right-Pointing-Pointer The extent of isothermal solidification increased with increasing holding time. Black-Right-Pointing-Pointer Homogenizing of joints resulted in the dissolution of DAZ intermetallics.

36 MATERIALS SCIENCE↗

Characterization of bulk stainless steel joints developed through microwave hybrid heating

Processing of metallic materials through microwave heating is a challenging area of research. In the present work, joining of stainless steel-316 to stainless steel-316 in the bulk form has been carried out by placing stainless steel-316 powder at the interface and through targeted heating using microwave hybrid heating. The trials were carried out in a multimode microwave applicator at a frequency of 2.45 GHz and power 900 W. The developed joints were characterized using X-ray diffraction, field emission scanning electron microscopy equipped with energy dispersive X-ray spectroscope and measurement of Vicker's microhardness, porosity and tensile strength. The X-ray diffraction spectrum of the developed joint shows the presence of chromium carbide, iron carbide and iron silicide phases that eventually contribute to enhancement of the microhardness of the joint. The scanning electron microscope micrographs confirm classical metallurgical bonding between the substrate and the interface (molten powder) layer; the epitaxial growth rate was observed adjacent to the fusion zone. The average observed Vicker's microhardness in the joint zone on the grain boundary was significantly higher than that inside the grains due to the presence of various hard phases at the grain boundaries. Evaluation of the tensile strength of the joints showed an average ultimate tensile strength of 425.0 MPa with an average elongation of 9.44%. - Highlights: • Joining of stainless steel (SS-316) plates using microwave hybrid heating • Epitaxial growth rate observed adjacent to the fusion zone of welded joint • The ultimate tensile strength of the order of 425.0 MPa with 9.44% elongation.

36 MATERIALS SCIENCE↗

Insight into the oxidation mechanism of Nb3Si(111) surface: First-principles calculations

Highlights: • Oxygen adsorption behavior on Nb{sub 3}Si(111) is studied by using first-principles. • O atom tends to be adsorbed on the NbSi bridge site. • The capacity of oxidation follow the order of Cr > Al > Si. • Cr can improve the Nb{sub 3}Si’s oxidation resistance because of Cr d-orbital effect. - Abstract: The oxidation resistance plays an important role in high-temperature ceramics. Although transition metal silicides exhibit the better oxidation behavior, the improvement of oxidation resistance is still a great challenge for their applications. Here, we apply first-principles calculations to investigate the oxidation mechanism and the influence of alloying elements (Cr and Al) on the oxidation resistance of Nb{sub 3}Si(111) surface. The calculated results show that the O atom is adsorbed on the NbSi-bridge site because of the charge interaction between O-2p state, Si-3p state and Nb-4d state. We further find that Cr-doping is more thermodynamically stable than that of Al-doping. In particular, the capacity of oxidation resistance follows the order of Cr > Al > Si. Finally, we conclude that Cr-doping can effectively improve the oxidation resistance of Nb{sub 3}Si(111) surface. The calculated electronic structure shows that Cr d-orbital plays a crucial role in oxidation resistance.

36 MATERIALS SCIENCE↗

In situ X-ray observation of phase transitions in Mg[subscript 2]Si under high pressure

The structural behavior of magnesium silicide (Mg{sub 2}Si) was investigated in a diamond anvil cell (DAC) by energy dispersive synchrotron X-ray diffraction up to 41.3 GPa at room temperature. Two pressure-induced structural phase transitions for Mg{sub 2}Si have been identified, at around 7.5 GPa and 21.3 GPa, respectively. The new structures of Mg{sub 2}Si are in turn determined as orthorhombic phase with anti-cotunnite (Pnma,Z=4) structure and hexagonal phase with Ni{sub 2}In-type (P6{sub 3}/mmc,Z=2) structure. Both the structural phase transitions are of first-order nature and are reversible.

36 MATERIALS SCIENCE↗

Leveraging computational thermodynamics to guide SiC-ZrC chemical vapor deposition process development

Here using the CALPHAD approach to understand zirconium carbide deposition, a series of phase equilibria were calculated from a custom thermodynamic database based on a literature source, and the equilibria were used to explore the potential chemical vapor deposition (CVD) processing space in the ZrCl 4 -CH 3 SiCl 3 -CH 4 -H 2 system as a function of pressure, temperature, and gas composition. Several gas ratios were considered. At a given ZrCl 4 :CH 3 SiCl 3 ratio within the range studied, the most important factor was found to be the ratios of CH 4 :ZrCl 4 , wherein the nature of the composition – carbide vs. silicide – could be controlled. A pure binary composition of ZrC and SiC is expected to form by increasing the initial amount of methane and decreasing the amount of hydrogen from values predicted purely based on thermodynamic equilibrium. Rietveld analysis of the x-ray diffractograms from corresponding experimental depositions confirmed that increasing the CH 4 :ZrCl 4 ratio increased the fraction of carbon-containing species (SiC, ZrC) and decreased the fraction of non-carbides (ZrSi, ZrSi 2 , etc.), as predicted from the CALPHAD results.

36 MATERIALS SCIENCE↗

Current-Phase Relations of Superconducting PtSi Constriction Josephson Junctions

Here, we study the current-phase relations of superconductor–constriction–superconductor Josephson junctions made from platinum silicide thin films by fabricating dc-superconducting quantum interference devices incorporating pairs of junctions and measuring their magnetic-field-dependent electrical transport. By comparing the supercurrent interference patterns with numerical Ginzburg–Landau simulations, we extract the current-phase relations of individual junctions and quantify the degree of nonlinearity. These measurements show that while the constrictions themselves sustain substantial nonlinearity, the effect is moderated by the kinetic inductance of the device leads, which is an important consideration for practical superconducting circuit applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Probing the Reactivity of the Active Material of a Li-Ion Silicon Anode with Common Battery Solvents

Calculations and modeling have shown that replacing the traditional graphite anode with silicon can greatly improve the energy density of lithium-ion batteries. However, the large volume change of silicon particles and high reactivity of lithiated silicon when in contact with the electrolyte lead to rapid capacity fading during charging/discharging processes. In this report, we use specific lithium silicides (LS) as model compounds to systematically study the reaction between lithiated Si and different electrolyte solvents, which provides a powerful platform to deconvolute and evaluate the degradation of various organic solvents in contact with the active lithiated Si-electrode surface after lithiation. Nuclear Magnetic Resonance (NMR) characterization results show that a cyclic carbonate such as ethylene carbonate is chemically less stable than a linear carbonate such as ethylmethyl carbonate, fluoroethylene carbonate, and triglyme as they are found to be more stable when mixed with LS model compounds. Furthermore, guided by the experimental results, two ethylene carbonate (EC)-free electrolytes are studied, and the electrochemical results show improvements with graphite-free Si electrodes relative to the traditional ethylene-carbonate-based electrolytes. More importantly, the study contributes to our understanding of the significant fundamental chemical and electrochemical stability differences between silicon and traditional graphite lithium-ion battery (LIB) anodes and suggests a focused development of electrolytes with specific chemical stability vs lithiated silicon which can passivate the surface more effectively.

25 ENERGY STORAGE↗

Real-Time NMR Investigations of Structural Changes in Silicon Electrodes for Lithium-Ion Batteries

Lithium-ion batteries (LIBs) containing silicon negative electrodes have been the subject of much recent investigation because of the extremely large gravimetric and volumetric capacity of silicon. The crystalline-to-amorphous phase transition that occurs on electrochemical Li insertion into crystalline Si, during the first discharge, hinders attempts to link structure in these systems with electrochemical performance. We apply a combination of static, in situ and magic angle sample spinning, ex situ {sup 7}Li nuclear magnetic resonance (NMR) studies to investigate the changes in local structure that occur in an actual working LIB. The first discharge occurs via the formation of isolated Si atoms and smaller Si-Si clusters embedded in a Li matrix; the latter are broken apart at the end of the discharge, forming isolated Si atoms. A spontaneous reaction of the lithium silicide with the electrolyte is directly observed in the in situ NMR experiments; this mechanism results in self-discharge and potential capacity loss. The rate of this self-discharge process is much slower when CMC (carboxymethylcellulose) is used as the binder.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Instability of U 3 Si 2 in pressurized water media at elevated temperatures

Following the Fukushima Daiichi accident, significant efforts from industry and the scientific community have been directed towards the development of alternative nuclear reactor fuels with enhanced accident tolerance. Among the proposed materials for such fuels is a uranium silicide compound (U 3 Si 2 ), which has been selected for its enhanced thermal conductivity and high density of uranium compared to the reference commercial light water reactor (LWR) nuclear fuel, uranium oxide (UO 2 ). To be a viable candidate LWR fuel, however, U 3 Si 2 must also demonstrate that, in the event of this fuel coming in contact with aqueous media, it will not degrade rapidly. In this contribution, we report the results of experiments investigating the stability of U 3 Si 2 in pressurized water at elevated temperatures and identify the mechanisms that control the interaction of U 3 Si 2 under these conditions. Our data indicate that the stability of this material is primarily controlled by the formation of a layer of USiO 4 (the mineral, coffinite) at the surface of U 3 Si 2 . The results also show that these layers are destabilized at T > 300 °C, leading to the complete decomposition of U 3 Si 2 and its pulverization due to its full oxidation to UO 2 .

36 MATERIALS SCIENCE↗

Surface and interface reactions of sputtered TiNi/Si thin films

We present the surface and interfacial chemical analysis of sputter deposited TiNi thin films over Si (100) substrates using Rutherford backscattering spectrometry (RBS), secondary ionization mass spectrometry (SIMS), and grazing incidence x-ray diffraction analysis. Upon annealing to high temperatures, significant diffusion of Ni into the Si substrate was observed. The analysis of the RBS and SIMS spectra confirm the net movement of the film species into the substrate. Further, we discuss the formation mechanism and the composition distribution surrounding the TiNi/Si interface that proves conducive for the nucleation and growth of the detected nickel silicide compound.

36 MATERIALS SCIENCE↗

Metastable Phase Formation During the Reaction of Ni Films with Si(001): the Role of Texture Inheritance

The thermally induced solid-state reaction between a 10-nm-thick Ni film and a Si(001) substrate was investigated using in situ x-ray diffraction and ex situ pole figure analyses. The reaction begins with the appearance of orthorhombic Ni{sub 2}Si grains characterized by a strong fiber texture. The formation of the metastable hexagonal {theta} phase - which inherits the fiber texture of Ni{sub 2}Si - is then observed. This phase has been observed in every sample studied regardless of dopant, film thickness, deposition method, and anneal profile (>2000 conditions). Texture inheritance allows a reaction pathway with a lower activation energy than the expected formation through thermodynamically stable Ni silicide phases.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

X-Ray And Polarized Neutron Reflectometry: Characterization Of Si/Co/Si And Si/Ni/Si Systems

Technologically important metal silicides formed through interdiffusion in metal/Si systems has been probed using two complementary techniques viz. x-ray reflectivity (XRR) and polarized neutron reflectivity (PNR). Both structural and magnetic characterization with good depth resolution has been achieved in these systems. We have studied two systems Si/Co/Si and Si/Ni/Si which relate to important applications in ferromagnetic/ non-magnetic semiconductor layered structures for memory devices.

36 MATERIALS SCIENCE↗

Optoelectronic properties of Mg{sub 2}Si semiconducting layers with high absorption coefficients

In an attempt to develop a low-cost material for solar cell devices, polycrystalline magnesium silicide (poly-Mg{sub 2}Si) semiconducting layers have been prepared by applying rf magnetron sputtering using a Mg{sub 2}Si target. The optimum substrate temperature for the poly-Mg{sub 2}Si growth was found to be T{sub s} = 200 deg. C; the film deposition at higher temperatures leads to desorption of Mg atoms from the growing surface, while the amorphous phase formation occurs at room temperature. The poly-Mg{sub 2}Si layer deposited at T{sub s} = 200 deg. C shows the (111) preferential orientation with a uniform grain size of {approx}50 nm. The dielectric function of the poly-Mg{sub 2}Si layer has been determined accurately by spectroscopic ellipsometry. From the analysis, quite high absorption coefficients and an indirect gap of 0.77 eV in the poly-Mg{sub 2}Si layer have been confirmed. The above poly-Mg{sub 2}Si layer shows clear photoconductivity and can be applied as a narrow-gap bottom layer in multi-junction solar cell devices.

36 MATERIALS SCIENCE↗