Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Dynamical behaviors of structural, constrained and free water in calcium- and magnesium-silicate-hydrate gels

We present the hypothesis that the mechanical properties of cement pastes depend strongly on their porosities. In a saturated paste, the porosity links to the free water volume after hydration. Structural water, constrained water, and free water have different dynamical behavior. Hence, it should be possible to extract information on pore system by exploiting the water dynamics. With our experiments we investigated the slow dynamics of hydration water confined in calcium- and magnesium-silicate-hydrate (C-S-H and M-S-H) gels using high-resolution quasi-elastic neutron scattering (QENS) technique. C-S-H and M-S-H are the chemical binders present in calcium rich and magnesium rich cements. We measured three M-S-H samples: pure M-S-H, M-S-H with aluminum-silicate nanotubes (ASN), and M-S-H with carboxyl group functionalized ASN (ASN-COOH). A C-S-H sample with the same water content (i.e. 0.3) is also studied for comparison. We found that structural water in the gels contributes to the elastic component of the QENS spectrum, while constrained water and free water contribute the quasi-elastic component. The quantitative analysis suggests that the three components vary for different samples and indicate the variance in the system porosity, which controls the mechanical properties of cement pastes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spectroscopic analysis of Eu{sup 3+} -and Eu{sup 3+}:Yb{sup 3+}-doped yttrium silicate crystalline powders prepared by combustion synthesis

Yttrium silicate powders doped with Eu{sup 3+} and codoped with Eu{sup 3+} and Yb{sup 3+} were prepared by combustion synthesis. The x-ray powder diffraction data showed the presence of Y{sub 2}SiO{sub 5} and Y{sub 2}Si{sub 2}O{sub 7} crystalline phases. Singly doped (1 wt %) sample illuminated with ultraviolet light ({lambda}=256 nm) showed the characteristic red luminescence corresponding to {sup 5}D{sub 0}{yields}{sup 7}F{sub J} transitions of Eu{sup 3+}. The Judd-Ofelt intensity parameters were calculated from experimental data and the radiative and nonradiative relaxation rates were estimated. The results showed that the nonradiative relaxation rate is smaller in yttrium silicate compared to yttrium oxide powder, a reference material, prepared under similar conditions. Codoped samples were exposed to near-infrared laser excitation ({lambda}=975 nm) and the red luminescence of Eu{sup 3+} was also observed. In this case, the luminescence is achieved due to a cooperative upconversion (CUC) process involving energy transfer (ET) from pairs of ytterbium ions to europium ions. The ET rate was estimated by fitting a rate equation model with the dynamics of CUC red emission.

36 MATERIALS SCIENCE↗

THE EFFECT OF HEAVY COSMIC-RAY IONS ON SILICATE GRAINS IN THE INTERSTELLAR DUST

Electronmicroscopic samples of crystalline Mg{sub 2}SiO{sub 4} forsterite were irradiated by energetic Ar, Fe, Kr, and Xe ions at room temperature. Tracks with a mean radius R{sub e} = 1.36 nm were observed after irradiation by 56 MeV Fe ions, while no tracks were induced by a 48 MeV Ar beam. Amorphization of forsterite grains by cosmic-ray (CR) Fe ions are discussed, including the effects of low temperature, ion velocity, and ion-induced crystallization. CR Fe ions induce amorphous tracks in crystalline forsterite only in the range 40-140 MeV, and the period of time for complete amorphization is tau{sub cr} approx 13,400 Myr. Our estimate is tau{sub cr} approx 1300 Myr for enstatite. Thus, heavy CR particles do not reduce the crystallinity of silicate grains within a reasonable time, as supposed previously. However, energetic ions can induce crystallization in amorphous solids, and this may be partially or fully responsible for the estimated 0.2% crystallinity of silicates in the interstellar medium.

79 ASTRONOMY AND ASTROPHYSICS↗

Solid-Phase Interaction of Uranium Tetrafluoride with Aluminum Silicates

The influence of the phase and chemical compositions of two aluminum silicate minerals – bentonite and kaolinite – on the solid-phase conversion of depleted uranium tetrafluoride into U {sub 3} O {sub 8} was investigated. It is shown that after their preliminary preparation by heat treatment or mechanical activation aluminum silicates can be used as reagents alternative to silica.

36 MATERIALS SCIENCE↗

Interactions between zirconia–yttria–tantala thermal barrier oxides and silicate melts

The effects of TaO 2.5 additions to Y 4 Zr 3 O 12 (YZO) on its interactions with calcium-magnesium alumino-silicate (CMAS) melts are investigated herein. YZO is a candidate material for the protection of novel ZrO 2 -YO 1.5 -TaO 2.5 based thermal barrier coatings (TBCs) against CMAS attack, but thermochemical considerations dictate that YZO contain TaO 2.5 for interfacial compatibility. Oxides based on Y 4 Zr 3-x Ta x O 12+0.5x ( x = =0, 0.7, 1.4) were mixed with various ternary and quinary silicate compositions ranging in Ca:Si ratio from 0.35 to 1.13 and equilibrated at 1300 °C. The results show that all combinations form the desired apatite phase except for the mixture of the higher Ta 5+ content with the lowest Ca:Si melt. It is found that the addition of Ta 5+ increases the capture of Y 3+ by the reprecipitated fluorite, decreasing the amount available to form apatite and eventually suppressing it at low Ca:Si. The effect is ascribed to the attractive interactions between Y 3+ and Ta 5+ in solid solution, similar to that found in tetragonal zirconia, but with concurrent incorporation of anion vacancies associated with excess Y 3+ that stabilize the cubic form. As the Ca 2+ content of the melt increases, so does the amount of Ca 2+ incorporated in fluorite. The latter also interacts attractively with Ta 5+ and leads to a reduction of captured Y 3+ in fluorite as the Ca content in the reacting deposit increases. This serves to increase the amount of Y 3+ available in the melt to form apatite in TBC-CMAS interactions.

36 MATERIALS SCIENCE↗

Mechanical Characterization of Low Modulus Polymer-Modified Calcium-Silicate-Hydrate (C-S-H) Binder

Calcium-silicate-hydrate (C-S-H) represents a key microstructural phase that governs the mechanical properties of concrete at a large scale. Defects in the C-S-H phase are also responsible for the poor ductility and low tensile strength of concrete. Manipulating the microstructure of C-S-H can lead to new cementitious materials with improved structural performance. This paper presents an experimental investigation aiming to characterize a new synthetic polymer-modified synthetic calcium-silicate-hydrate (C-S-H)/styrene-butadiene rubber (SBR) binder. The new C-S-H/SBR binder is produced by calcining calcium carbonate and mixing this with fumed silica (SiO 2 ), deionized water and SBR. Mechanical, physical, chemical and microstructural characterization was conducted to measure the properties of new hardened C-S-H binder. Results from the experimental investigation demonstrate the ability to engineer a new C-S-H binder with low elastic modulus and improved toughness and bond strength by controlling the SBR content and method of C-S-H synthesis. The new binder suggests the possible development of a new family of low-modulus silica-polymer binders that might fit many engineering applications such as cementing oil and gas wells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On the nature of structural disorder in calcium silicate hydrates with a calcium/silicon ratio similar to tobermorite

Four calcium silicate hydrates (C-S-H) with structural calcium/silicon (Ca/Si) ratios ranging from 0.82 ± 0.02 to 0.87 ± 0.02 were synthesized at room temperature, 50, 80, and 110 °C. Their structure was elucidated by collating information from electron probe micro-analysis, transmission electron microscopy, extended X-ray absorption fine structure spectroscopy, and powder X-ray diffraction (XRD). A modeling approach specific to defective minerals was used because sample turbostratism prevented analysis using usual XRD refinement techniques (e.g. Rietveld analysis). It is shown that C-S-H with Ca/Si ratio of ∼ 0.8 are structurally similar to nano-crystalline turbostratic tobermorite, a naturally occurring mineral. Their structure thus consists of sheets of calcium atoms in 7-fold coordination, covered by ribbons of silicon tetrahedra with a dreierketten (wollastonite-like) organization. In these silicate ribbons, 0.42 Si per bridging tetrahedron are missing. Random stacking faults occur systematically between successive layers (turbostratic stacking). Layer-to-layer distance is equal to 11.34 Å. Crystallites have a mean size of 10 nm in the a–b plane, and a mean number of 2.6–2.9 layers stacked coherently along the c* axis.

36 MATERIALS SCIENCE↗

Ion-specific effects influencing the dissolution of tricalcium silicate

It has been recently demonstrated that the dissolution kinetics of tricalcium silicate (C{sub 3}S) is driven by the deviation from its solubility equilibrium. In this article, special attention is paid to ions relevant in cement chemistry likely to interact with C{sub 3}S. In order to determine whether specific effects occur at the interface C{sub 3}S–water, particular efforts have been made to model ion activities using Pitzer's model. It has been found that monovalent cations and monovalent anions interact very little with the surface of C{sub 3}S. On the other side, divalent anions like sulfate slow down the dissolution more strongly by modifying the surface charging of C{sub 3}S. Third, aluminate ions covalently bind to surface silicate monomers and inhibit the dissolution in mildly alkaline conditions. The formation and the breaking of these bonds depend on pH and on [Ca{sup 2+}]. Thermodynamic calculations performed using DFT combined with the COSMO-RS solvation method support the experimental findings.

36 MATERIALS SCIENCE↗

Inorganic polymers from laterite using activation with phosphoric acid and alkaline sodium silicate solution: Mechanical and microstructural properties

Geopolymers from laterite, an iron-rich soil available in developing countries, have great potential as building materials. In this work, laterite from Togo (Africa) was used to prepare geopolymers using both phosphoric acid and alkaline sodium silicate solution. Microstructural properties were investigated by scanning electron microscopy, X-ray powder diffraction and mercury porosimetry, whereas thermal properties were evaluated by thermal analyses. The local environment of iron was studied by X-ray Absorption Spectroscopy (XANES region). The mechanical properties were determined. Modulus of Rupture and Young's modulus fell in the ranges 3.3–4.5 MPa and 12–33 GPa, respectively, rendering the materials good candidates for construction purposes. Heating above 900 °C results in weight-gain, presumably due to iron redox reactions. X-ray Absorption Spectroscopy data evidence changes in the chemical and structural environments of iron following thermal treatment of geopolymers. These changes indicate interaction between the geopolymer structure and iron during heating, possibly leading to redox properties. -- Highlights: •Geopolymerization of laterite is promising for fabrication of building materials. •Both phosphoric acid and alkaline sodium silicate solution can be used for activation. •Thermally activated redox properties of the inorganic polymers were observed.

36 MATERIALS SCIENCE↗

Crystal structure of magnesium silicate hydrates (M-S-H): The relation with 2:1 Mg–Si phyllosilicates

Two magnesium silicate hydrates (M-S-H) with structural magnesium/silicon ratios of 0.57 ± 0.08 and 1.07 ± 0.13 were synthesized at room temperature, with one year of synthesis duration. Their structure was clarified by considering results from X-ray diffraction, TEM, {sup 29}Si MAS NMR spectroscopy, TGA, and EPMA. A modeling approach appropriate to defective minerals was used because usual XRD refinement techniques cannot be used in the case of turbostratic samples, where coherency between successive layers is lost. M-S-H with Mg/Si ratio of ~ 0.6 appears to be structurally close to nanocrystalline turbostratic 2:1 Mg–Si phyllosilicates. The increase of the Mg/Si ratio from 0.6 to 1.2 occurs by increasing the occurrence of defects in the silicate plan. The layer-to-layer distance evolves from 9.46 Å to 14 Å under air-dried and ethylene glycol conditions, respectively. Crystallites have a mean size of 1.5 nm in the ab plane, and 2.4 nm along c*.

36 MATERIALS SCIENCE↗

Use of micro-reactors to obtain new insights into the factors influencing tricalcium silicate dissolution

A micro-reactor approach, developed previously, is used to study the early dissolution of tricalcium silicate. This approach uses micron-sized gaps mimicking particles in close contact to understand dissolution, nucleation, and growth processes. The main factors influencing the dissolution kinetics of tricalcium silicate are presented. We show that the presence of defects caused by polishing does not affect the extent of dissolution. A strong effect of aluminum in solution reducing the extent of dissolution is however identified. This effect is highly dependent on the pH, and is much lower above pH 13. We show also that superplasticizers reduce the extent of dissolution; however, the exact reason for this effect is not clear.

36 MATERIALS SCIENCE↗

Early reactivity of sodium silicate-activated slag pastes and its impact on rheological properties

The fast loss of fluidity of sodium silicate-activated slag (SS-AAS) systems have been widely studied in the literature. In this study, the rheology of these cements has been correlated with the evolution of the reaction products formed over time. For this purpose, a combination of experimental characterization techniques, to study the pore solution composition and microstructure of SS-AAS pastes and thermodynamic calculations have been applied. The initial precipitation of ill-defined N-A-S-H and C-N-A-S-H producta leads to a fast increase of the storage modulus after 40 min of reaction. These products are formed from the reaction of the Na{sup +} ions and silicate ions of the activator with the Ca{sup 2+} and aluminate species dissolved from the slag. However, when a shear is applied, the structure breaks down and fluidity is recovered, that infers that the attractive forces between the particles are low at the early stages of hydration.

36 MATERIALS SCIENCE↗

Effects of alkali dosage and silicate modulus on autogenous shrinkage of alkali-activated slag cement paste

Autogenous shrinkage of alkali-activated slag cement (AASC) paste prepared with different levels of alkali dosage and silicate modulus (M{sub s}) is investigated. The results show that autogenous shrinkage of AASC paste increases at a decreasing rate with alkali dosage, which is attributed to enhanced capillary pore pressure and syneresis of C-A-S-H gels. Autogenous shrinkage of AASC paste with a constant alkali dosage increases as M{sub s} increases from 0.5 to 1.0, followed with a reduction as M{sub s} further increases to 2.0. Increasing M{sub s} initially enhances the capillary pore pressure due to the enhanced reaction degree, and promotes the formation of saturated capillary pores and viscoelasticity, which facilitates the autogenous shrinkage of AASC paste. However, excessive silicate in the activator retards the internal moisture consumption, and subsequently decreases the autogenous shrinkage of AASC paste. Furthermore, increasing M{sub s} can also intensify syneresis of C-A-S-H gels, contributing to the early-age autogenous shrinkage of AASC paste.

36 MATERIALS SCIENCE↗

Strain hardening magnesium-silicate-hydrate composites (SHMSHC) reinforced with short and randomly oriented polyvinyl alcohol microfibers

Magnesium-silicate-hydrate (M-S-H) cement has emerged as an alternative binder with potentially lower energy requirements and emissions. Due to the intrinsically low pH values of its matrix, however, normal steel reinforcement is not appropriate for M-S-H system. To toughen the matrix and to overcome the brittle nature of the material, a new strain hardening magnesium-silicate-hydrate composite (SHMSHC) is developed for the first time by incorporating 2 vol% short and randomly oriented polyvinyl alcohol (PVA) microfibers. The resulting SHMSHC exhibits significant strain hardening with a tensile strain capacity of more than 3%, a compressive strength beyond 50 MPa and a tensile strength of around 3 MPa. Remarkably, saturated multiple cracking with a tight crack width less than 10 μm invisible to the human naked eyes was observed. The newly developed SHMSHC addresses the fundamental challenge of M-S-H binder and is expected to widen possible application areas of M-S-H system.

36 MATERIALS SCIENCE↗

Ion irradiation study of lithium silicates for fusion blanket applications

Here, this study reports on the microstructural and compositional evolutions, deuterium release and lithium loss behavior in lithium silicates. Pellets of biphasic Li 4 SiO 4 and Li 2 SiO 3 were fabricated using hot pressing of powders. Sequential irradiation with Si + , He + and D + ions was performed up to 773 K to emulate one-year 6 Li burnup in 6 Li 4 SiO 4 inside the SlimCS DEMO. Crystalline Li 4 SiO 4 phase was not observed in the irradiated depth region of all the samples in this study. In spite of full amorphization in the near-surface region, Li 2 SiO 3 irradiated to a high dose at 773 K remained crystalline in the damage peak region, suggesting that Li 2 SiO 3 is more irradiation resistant to amorphization than Li 4 SiO 4 . Radiolysis may be primarily responsible for silicate decomposition and amorphization. Data from this study also show that D release from the pellet is very efficient during ion irradiation at 773 K, which is accompanied with a significant Li loss. Thermal annealing for 10 min at 773 K for the room-temperature irradiated pellet leads to a nearly complete D release without an observable Li loss. A concept of Ni coating on tritium breeder materials is discussed with supporting data to minimize Li loss without a significant impact on tritium diffusion and release.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Formation mechanism and luminescence appearance of Mn-doped zinc silicate particles synthesized in supercritical water

Luminescence appearance of Mn-doped zinc silicate (Zn{sub 2}SiO{sub 4}:Mn{sup 2+}, ZSM) formed in supercritical water at 400 deg. C and 29 MPa at reaction times from 1 to 4320 min was studied in the relation to its phase formation mechanism. Appearance of luminescent ZSM from green emission by {alpha}-ZSM and yellow emission by {beta}-ZSM occurred over the same time period during the onset of phase formation at a reaction time of 2 min. Luminescence appeared at a much lower temperature and at shorter reaction times than the conventional solid-state reaction. Needle-like-shaped {alpha}-ZSM was the most stable particle shape and phase in the supercritical water reaction environment and particles formed via two routes: a homogenous nucleation route and a heterogenous route that involves solid-state diffusion and recrystallization. - Graphical abstract: Luminescence appearance of Mn-doped zinc silicate (Zn{sub 2}SiO{sub 4}:Mn{sup 2+}, ZSM) formed in supercritical water at 400 deg. C and 29 MPa were studied in the relation to its phase formation mechanism. Green emission by {alpha}-ZSM and yellow emission by {beta}-ZSM occurred over the same time period during the onset of phase formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Computerized crystal-chemical classification of silicates and related materials with CRYSTANA and formula notation for classified structures

The computer program CRYSTANA is described which implements a method for the crystal-chemical classification of silicates and related materials. This method is mainly based upon the topological structure of the connected units of a compound and can be applied when the units are built from tetrahedra as coordination polyhedra. The classification parameters and the rules which have to be applied for their determination are summarized and a formalization of the method is provided based upon a finite graph representation of the units. A description of how CRYSTANA can be used and which kind of output it produces is included. From this output crystal-chemical formulas can be derived, which differ slightly from an existing notation in order to meet recommendations of the International Union of Crystallography. - The computer program CRYSTANA is described which implements a method for the crystal-chemical classification of silicates and related materials. The implementation is based upon a graph-theoretical formalization of the classification method. An extended notation of crystal-chemical formulas is introduced. The formulas can be derived from the output of the program.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Antimony and silicon environments in antimony silicate glasses

Antimony silicate glasses, of general formula xSb{sub 2}O{sub 3}.(1-x)SiO{sub 2} (0.1{<=}x{<=}0.78), have been prepared by melt-quenching and their structures studied using {sup 29}Si MAS NMR spectroscopy, {sup 121}Sb Moessbauer spectroscopy and Raman spectroscopy. Oxidation during melting gives rise to Sb{sup 5+} in concentrations, which increase linearly with x to give a value of {approx}10% when x=0.78. {sup 121}Sb Moessbauer spectra show Moessbauer shifts and quadrupole splittings consistent with Sb{sup 3+} in a [:SbO{sub 3}] trigonal pyramid, similar to that in crystalline Sb{sub 2}O{sub 3}. A broad band in the Raman spectrum at {approx}410 cm{sup -1} is due to the vibrations of such a unit. The dependence of the silicon Q{sup n} speciation on x can be interpreted by the formation of Sb-O-Sb links possibly to form rings of 4 [:SbO{sub 3}] units such as are found in valentinite. - Graphical abstract: Antimony silicate glasses have been shown to contain Sb{sup 3+} in [:SbO{sub 3}] trigonal pyramid units using {sup 121}Sb Moessbauer spectroscopy and Raman spectroscopy. {sup 29}Si magic-angle-spinning NMR has shown silicon Q{sup n} speciation which can be interpreted as formation of rings of 4 [:SbO{sub 3}] units such as are found in valentinite.

36 MATERIALS SCIENCE↗