Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RAM analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Excitation mechanisms in 1 mJ picosecond laser induced low pressure He plasma and the resulting spectral quality enhancement

We report in this paper the results of an experimental study on the spectral and dynamical characteristics of plasma emission induced by 1 mJ picoseconds (ps) Nd-YAG laser using spatially resolved imaging and time resolved measurement of the emission intensities of copper sample. This study has provided the experimental evidence concerning the dynamical characteristics of the excitation mechanisms in various stages of the plasma formation, which largely consolidate the basic scenarios of excitation processes commonly accepted so far. However, it is also clearly shown that the duration of the shock wave excitation process induced by ps laser pulses is much shorter than those observed in laser induced breakdown spectroscopy employing nanosecond laser at higher output energy. This allows the detection of atomic emission due exclusively to He assisted excitation in low pressure He plasma by proper gating of the detection time. Furthermore, the triplet excited state associated with He I 587.6 nm is shown to be the one most likely involved in the process responsible for the excellent spectral quality as evidenced by its application to spectrochemical analysis of a number of samples. The use of very low energy laser pulses also leads to minimal destructive effect marked by the resulted craters of merely about 10 μm diameter and only 10 nm deep. It is especially noteworthy that the excellent emission spectrum of deuterium detected from D-doped titanium sample is free of spectral interference from the undesirable ubiquitous water molecules without a precleaning procedure as applied previously and yielding an impressive detection limit of less than 10 μg/g. Finally, the result of this study also shows a promising application to depth profiling of impurity distribution in the sample investigated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Offshore Wind Farm Turbine and Energy Storage Optimization

Abstract This paper evaluates the technical and economic feasibility of repurposing decommissioned offshore oil and gas platforms as electrical substations for offshore wind projects in the U.S. Gulf of America, a region characterized by relatively low and highly variable wind speeds, extensive legacy offshore infrastructure, and exposure to merchant electricity markets. A unified techno-economic framework is developed using the Repurposing Offshore Infrastructure for Continued Energy (ROICE) Economic Model (REM) to integrate Gulfspecific wind resource assessment, commercial wind turbine performance, offshore infrastructure cost modeling, and wholesale electricity market exposure. Gulf wind speed data are vertically extrapolated to turbine hub height and combined with manufacturer power curves to compute annual energy production and capacity factors across a broad portfolio of commercial turbines, enabling identification of turbine designs best suited for low-wind offshore environments. Hourly electricity price data from the Midcontinent Independent System Operator (MISO) day-ahead market are incorporated to characterize revenue potential, price volatility, and the temporal alignment between wind generation and market conditions. In addition, a conceptual framework for offshore battery energy storage system (BESS) integration is developed to support future investigation of market-responsive energy shifting at repurposed platforms. Results from the turbine evaluation demonstrate that machines with lower cut-in wind speeds and earlier ‘rated-power’ characteristics significantly outperform larger, industry-standard offshore turbines for the same net power under Gulf wind conditions, underscoring the need for region-specific technology selection. Market analysis further reveals substantial price variability and limited intrinsic alignment between wind production and high-price periods, motivating consideration of operational flexibility mechanisms. While storage optimization is not implemented in this study, the REM framework establishes a transparent and replicable foundation for co-evaluating turbine selection, infrastructure constraints, and market exposure, providing a practical pathway for assessing the potential role of repurposed offshore platforms in enabling economically viable offshore wind development in the Gulf of America.

02 PETROLEUM↗
NASA NTRS1995

Diffuse hot gas in the NGC 4261 group of galaxies

We have found diffuse X-ray gas in the group of galaxies containing the elliptical galaxy NGC 4261. This galaxy along with its associated companions are behind the Virgo cluster in the W-cloud. A recent analysis of the velocity structure in the Virgo region indicates that the W-cloud has approximately 30 members, most of which are low luminosity dwarfs. The hot X-ray emitting gas is centered about halfway between NGC 4261 and NGC 4264 and extends out to a radius of approximately 40 min(620 kpc). The spectral data for the diffuse component are well fitted with a Raymond-Smith plasma model with a temperature of 0.85(sup +0.21)(sub -0.16) keV and abundance less than 0.08 times the solar value. Under the assumption that the diffuse gas is in hydrostatic equilibrium the total mass within 40 min is 1.9 x 10(exp 13) solar mass. We estimate that the total baryonic mass of the hot gas and the galaxies is 20%-34% of the total mass in the central 40 min radius of this group. This group of galaxies contains NGC 4273 which exhibits a 'bow shock' morphology similar to that of NGC 2276. This is thought to occur when the ram pressure from the intragroup gas significantly perturbs the interstellar medium in a late-type galaxy. We show that this is unlikely in this group.

Davis, David S.↗
DOE OSTI2014

THE CURIOUS MORPHOLOGY AND ORIENTATION OF ORION PROPLYD HST-10

HST-10 is one of the largest proplyds in the Orion Nebula and is located approximately 1' SE of the Trapezium. Unlike other proplyds in Orion, however, the long-axis of HST-10 does not align with θ{sup 1} C, but is instead aligned with the rotational axis of the HST-10 disk. This cannot be easily explained using current photoevaporation models. In this Letter, we present high spatial resolution near-infrared images of the Orion proplyd HST-10 using Keck/NIRC2 with the Laser Guide Star Adaptive Optics system, along with multi-epoch analysis of HH objects near HST-10 using Hubble Space Telescope (HST) WFPC2 and Advanced Camera for Surveys cameras. Our narrowband near-IR images resolve the proplyd ionization front (IF) and circumstellar disk down to 23 AU at the distance to Orion in Br γ, He I, H{sub 2}, and polycyclic aromatic hydrocarbon (PAH) emission. Br γ and He I emission primarily trace the IF (with the disk showing prominently in silhouette), while the H{sub 2} and PAH emission trace the surface of the disk itself. PAH emission also traces small dust grains within the proplyd envelope which is asymmetric and does not coincide with the IF. The curious morphology of the PAH emission may be due to UV heating by both θ{sup 1} COri and θ{sup 2} AOri. Multi-epoch HST images of the HST-10 field show proper motion of three knots associated with HH 517, clearly indicating that HST-10 has a jet. We postulate that the orientation of HST-10 is determined by the combined ram pressure of this jet and the FUV-powered photo-ablation flow from the disk surface.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Vertically Aligned Carbon Nanotubes Grown on Copper Foil as Electrodes for Electrochemical Double Layer Capacitors

This study reports a binder-free, catalyst-free method for fabricating vertically aligned carbon nanotubes (VACNTs) directly on copper (Cu) foil using plasma-enhanced chemical vapor deposition (PECVD) for electrochemical double-layer capacitor (EDLC) applications. This approach eliminates the need for catalyst layers, polymeric binders, or substrate pre-treatments, simplifying electrode design and enhancing electrical integration. The resulting VACNTs form a dense, uniform, and porous array with strong adhesion to the Cu substrate, minimizing contact resistance and improving conductivity. Electrochemical analysis shows gravimetric specific capacitance (C grav ) and areal specific capacitance (C areal ) of 8 F g −1 and 3.5 mF cm −2 at a scan rate of 5 mV/s, with low equivalent series resistance (3.70 Ω) and charge transfer resistance (0.48 Ω), enabling efficient electron transport and rapid ion diffusion. The electrode demonstrates excellent rate capability and retains 92% of its initial specific capacitance after 3000 charge–discharge cycles, indicating strong cycling stability. These results demonstrate the potential of directly grown VACNT-based electrodes for high-performance EDLCs, particularly in applications requiring rapid charge–discharge cycles and sustained energy delivery.

25 ENERGY STORAGE↗
NASA NTRS1993

LDEF Space Plasma-High Voltage Drainage Experiment post-flight results

The Space Plasma-High Voltage Drainage Experiment (SP-HVDE) was comprised of two identical experimental trays. With one tray located on the leading (ram facing, B10) edge and the other located on the trailing (wake facing, D4) edge of the Long Duration Exposure Facility (LDEF), it was possible to directly compare the effects of ram and wake spacecraft environments on charged dielectric materials. Six arrays of Kapton dielectric samples of 2 mil, 3 mil, and 5 mil thicknesses maintained at +/- 300, +/- 500, and +/- 1000 voltage bias formed the experimental matrix of each tray. In addition, each tray carried two solar cell strings, one biased at +300 volts and the other at -300 volts, to study current leakage from High Voltage Solar Arrays (HVSA). The SP-HVDE provides the first direct, long-term, in-flight measurements of average leakage current through dielectric materials under electric stress. The experiment also yields information on the long term stability of the bulk dielectric properties of such materials. Data and findings of the SP-HVDE are an extension of those from shorter term flight experiments such as the PIX-1 (Plasma Interaction Experiment) and PIX-2 and are therefore valuable in the design and evaluation of long-lived space systems with high voltage systems exposed to the low earth orbital environment. A summary of the SP-HVDE post flight analysis final report delivered to the LDEF Project Office under contract to the National Aeronautics and Space Administration is presented.

Yaung, J. Y.↗
DOE OSTI2015

Blackberry extract inhibits UVB-induced oxidative damage and inflammation through MAP kinases and NF-κB signaling pathways in SKH-1 mice skin

Extensive exposure of solar ultraviolet-B (UVB) radiation to skin induces oxidative stress and inflammation that play a crucial role in the induction of skin cancer. Photochemoprevention with natural products represents a simple but very effective strategy for the management of cutaneous neoplasia. In this study, we investigated whether blackberry extract (BBE) reduces chronic inflammatory responses induced by UVB irradiation in SKH-1 hairless mice skin. Mice were exposed to UVB radiation (100 mJ/cm{sup 2}) on alternate days for 10 weeks, and BBE (10% and 20%) was applied topically a day before UVB exposure. Our results show that BBE suppressed UVB-induced hyperplasia and reduced infiltration of inflammatory cells in the SKH-1 hairless mice skin. BBE treatment reduced glutathione (GSH) depletion, lipid peroxidation (LPO), and myeloperoxidase (MPO) in mouse skin by chronic UVB exposure. BBE significantly decreased the level of pro-inflammatory cytokines IL-6 and TNF-α in UVB-exposed skin. Likewise, UVB-induced inflammatory responses were diminished by BBE as observed by a remarkable reduction in the levels of phosphorylated MAP Kinases, Erk1/2, p38, JNK1/2 and MKK4. Furthermore, BBE also reduced inflammatory mediators such as cyclooxygenase-2 (COX-2), prostaglandin E{sub 2} (PGE{sub 2}), and inducible nitric oxide synthase (iNOS) levels in UVB-exposed skin. Treatment with BBE inhibited UVB-induced nuclear translocation of NF-κB and degradation of IκBα in mouse skin. Immunohistochemistry analysis revealed that topical application of BBE inhibited the expression of 8-oxo-7, 8-dihydro-2′-deoxyguanosine (8-oxodG), cyclobutane pyrimidine dimers (CPD), proliferating cell nuclear antigen (PCNA), and cyclin D1 in UVB-exposed skin. Collectively, these data indicate that BBE protects from UVB-induced oxidative damage and inflammation by modulating MAP kinase and NF-κB signaling pathways. - Highlights: • Blackberry extract inhibits UVB-induced glutathione depletion. • Blackberry extract inhibits UVB-induced lipid peroxidation. • Blackberry extract inhibits UVB-induced myeloperoxidase activity. • Blackberry extract diminishes UVB-induced inflammatory responses. • Blackberry extract prevents skin from oxidative damage and inflammation by UVB.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2016

The grism lens-amplified survey from space (glass). VII. The diversity of the distribution of star formation in cluster and field galaxies at 0.3 ≤ z ≤ 0.7

Exploiting the slitless spectroscopy taken as part of the Grism Lens-Amplified Survey from Space (GLASS), we present an extended analysis of the spatial distribution of star formation in 76 galaxies in 10 clusters at 0.3<z<0.7. We use 85 foreground and background galaxies in the same redshift range as a field sample. The samples are well matched in stellar mass (10{sup 8}−10{sup 11} M{sub ⊙}) and star formation rate (0.5–50 M{sub ⊙} yr{sup −1}). We visually classify galaxies in terms of broad band morphology, Hα morphology, and likely physical process acting on the galaxy. Most Hα emitters have a spiral morphology (41% ± 8% in clusters, 51% ± 8% in the field), followed by mergers/interactions (28% ± 8%, 31% ± 7%, respectively) and early-type galaxies (remarkably as high as 29% ± 8% in clusters and 15% ± 6% in the field). A diversity of Hα morphologies is detected, suggesting a diversity of physical processes. In clusters, 30% ± 8% of the galaxies present a regular morphology, mostly consistent with star formation diffused uniformly across the stellar population (mostly in the disk component, when present). The second most common morphology (28% ± 8%) is asymmetric/jellyfish, consistent with ram-pressure stripping or other non-gravitational processes in 18% ± 8% of the cases. Ram-pressure stripping appears significantly less prominent in the field (2% ± 2%), where the most common morphology/mechanism appears to be consistent with minor gas-rich mergers or clump accretion. This work demonstrates that while environment-specific mechanisms affect galaxy evolution at this redshift, they are diverse and their effects are subtle. A full understanding of this complexity requires larger samples and detailed and spatially resolved physical models.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2015

Final Scientific/Technical Report – DE-EE0002960 Recovery Act. Detachment faulting and Geothermal Resources - An Innovative Integrated Geological and Geophysical Investigation of Pearl Hot Spring, Nevada

The Pearl Host Spring Geothermal Project funded by the DoE Geothermal Program was a joint academic (KU/UT & OU) and industry collaboration (Sierra and Ram Power) to investigate structural controls and the importance of low-angle normal faults on geothermal fluid flow through a multifaceted geological, geophysical, and geochemical investigation in west-central Nevada. The study clearly showed that the geothermal resources in Clayton Valley are controlled by the interplay between low-angle normal faults and active deformation related to the Walker Lane. The study not only identified potentially feasible blind geothermal resource plays in eastern Clayton Valley, but also provide a transportable template for exploration in the area of west-central Nevada and other regional and actively-deforming releasing fault bends. The study showed that deep-seated low-angle normal faults likely act as crustal scale permeability boundaries and could play an important role in geothermal circulation and funneling geothermal fluid into active fault zones. Not unique to this study, active deformation is viewed as an important gradient to rejuvenated fracture permeability aiding the long-term viability of blind geothermal resources. The technical approach for Phase I included the following components, (1) Structural and geological analysis of Pearl Hot Spring Resource, (2) (U-Th)/He thermochronometry and geothermometry, (3) detailed gravity data and modeling (plus some magnetic and resistivity), (4) Reflection and Refraction Seismic (Active Source), (5) Integration with existing and new geological/geophysical data, and (6) 3-D Earth Model, combining all data in an innovative approach combining classic work with new geochemical and geophysical methodology to detect blind geothermal resources in a cost-effective fashion.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Dynamic data-driven multiscale modeling for predicting the degradation of a 316L stainless steel nuclear cladding material

Here, we have developed a long short-term memory stacked ensemble (LSTM-SE) surrogate modeling approach that can provide rapid predictions of microstructural evolution and the resultant mechanical properties of American Iron and Steel Institute (AISI) 316L series stainless steel (316LSS) fuel cladding under conditions of varying temperature and radiation dose rate. To acquire training data, we developed and implemented a kinetic Monte Carlo (KMC) model to simulate precipitation kinetics of M 23 C 6 , γ', and G phases within SS316L cladding. Experimentally reported precipitation kinetics of SS316L in literature were linked to the kinetic parameters of the simulated precipitation in our KMC model. The model was then used to simulate microstructure evolution under synthetically generated treatments of varying temperature and radiation dose rate, for periods of up to 3000 hours. Changes in volume fraction, number density, and particle size of precipitates were recorded, and particle area fractions were correlated using statistical methods to develop the surrogate model. Simultaneously, the mechanical properties of the simulated microstructures were evaluated using microstructure-based finite element method (FEM) analysis to determine the elastic modulus, yield stress, ultimate tensile strength, and elongation to failure of the aged microstructures. Using this approach, our surrogate model can predict precipitation behavior within 0.25% volume fraction and mechanical properties within 6% relative error from the values predicted by the KMC and FEM models using 50 training simulations as input. The trained recurrent neural network-based model can return estimations of precipitation kinetics and mechanical properties ~1000 times faster than the physics-based codes. This work demonstrates, as a proof of concept, that reactor material service lifetimes under variable service conditions can be predicted for a statistics-based model from a practicably obtainable dataset.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic Data-Driven Multiscale Modeling for Predicting Microstructure and Mechanical Properties of 316L Stainless Steel

We have developed a long short-term memory stacked ensemble (LSTM-SE) surrogate modeling approach that can provide rapid predictions of microstructural evolution and the resultant mechanical properties of American Iron and Steel Institute (AISI) 316L series stainless steel (316LSS) fuel cladding under conditions of varying temperature and radiation dose rate. To acquire training data, we developed and implemented a kinetic Monte Carlo (KMC) model to simulate precipitation kinetics of M 23 C 6 , γ', and G phases within SS316L cladding. Experimentally reported precipitation kinetics of SS316L in literature were linked to the kinetic parameters of the simulated precipitation in our KMC model. The model was then used to simulate microstructure evolution under synthetically generated treatments of varying temperature and radiation dose rate, for periods of up to 3000 hours. Changes in volume fraction, number density, and particle size of precipitates were recorded, and particle area fractions were correlated using statistical methods to develop the surrogate model. Simultaneously, the mechanical properties of the simulated microstructures were evaluated using microstructure-based finite element method (FEM) analysis to determine the elastic modulus, yield stress, ultimate tensile strength, and elongation to failure of the aged microstructures. Using this approach, our surrogate model can predict precipitation behavior within 0.25% volume fraction and mechanical properties within 6% relative error from the values predicted by the KMC and FEM models using 50 training simulations as input. The trained recurrent neural network-based model can return estimations of precipitation kinetics and mechanical properties ~1000 times faster than the physics-based codes. This work demonstrates, as a proof of concept, that reactor material service lifetimes under variable service conditions can be predicted for a statistics-based model from a practicably obtainable dataset.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Theoretical and computational studies on the scattering of radio frequency waves by fluctuations

The practical and economic viability of tokamak fusion reactors depends, in a significant way, on the efficiency of radio frequency (RF) waves to deliver energy and momentum to the plasma in the core of the reactor. Among the various attributes of RF waves is their ability to heat magnetically confined plasmas, induce plasma currents in an effort to achieve steady state, and modify the current profile so as to control plasma instabilities like the neoclassical tearing modes. The RF electromagnetic waves, excited by antenna structures placed near the wall of a tokamak, have to propagate through the turbulent plasma in the scrape-off layer (SOL) along their path to the core plasma. While the propagation and damping of RF waves in the core is reasonably well understood, the same is not true for RF propagation through the SOL. In present day fusion devices, the radial width of the SOL is of the order of a few centimeters. In ITER and in future fusion reactors this width will be of the order of tens of centimeters. Any deleterious effects on RF waves due to plasma turbulence in the SOL has to be properly understood in order to optimize the delivery of RF energy and momentum into the core. This paper is on a multi-pronged approach that is being pursued to quantify the effect of SOL plasma on RF waves. The SOL is composed of coherent filamentary, or blob like, structures and incoherent fluctuations. For coherent structures a full-wave theoretical model has been developed. This model is used to benchmark computational codes that are subsequently used to study general distribution of filaments, thereby extending the range of the theoretical formulation. For incoherent fluctuations, a common approach towards quantifying the effects of turbulence is the Kirchhoff technique. This technique is based on physical optics and the wave fields at any point on a spatially varying surface are approximated to be the same as the fields on a tangent plane at that point. The results from the theoretical analysis are compared with full-wave numerical simulations for incoherent fluctuations. The final part of these studies is to construct the effective permittivity of a turbulent plasma that is a mix of coherent and incoherent fluctuations. Towards this end, the ``effective medium approximation'' is being used to construct the permittivity of the turbulent plasma that will be used in full-wave and physical optics studies of scattering. All these approaches are distinctly different from previous studies on the RF wave propagation through turbulent plasmas. The theory and computations discussed in this paper apply to RF waves in any frequency range and for arbitrary variations in density, and reveal new and important physical insights into the scattering of RF waves.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2017

PIC simulations of wave-particle interactions with an initial electron velocity distribution from a kinetic ring current model

Whistler wave-particle interactions play an important role in the Earth inner magnetospheric dynamics and have been the subject of numerous investigations. By running a global kinetic ring current model (RAM-SCB) in a storm event occurred on Oct 23–24 2002, we obtain the ring current electron distribution at a selected location at MLT of 9 and L of 6 where the electron distribution is composed of a warm population in the form of a partial ring in the velocity space (with energy around 15 keV) in addition to a cool population with a Maxwellian-like distribution. The warm population is likely from the injected plasma sheet electrons during substorm injections that supply fresh source to the inner magnetosphere. These electron distributions are then used as input in an implicit particle-in-cell code (iPIC3D) to study whistler-wave generation and the subsequent wave-particle interactions. Here, we find that whistler waves are excited and propagate in the quasi-parallel direction along the background magnetic field. Several different wave modes are instantaneously generated with different growth rates and frequencies. The wave mode at the maximum growth rate has a frequency around 0.62ω ce , which corresponds to a parallel resonant energy of 2.5 keV. Linear theory analysis of wave growth is in excellent agreement with the simulation results. These waves grow initially due to the injected warm electrons and are later damped due to cyclotron absorption by electrons whose energy is close to the resonant energy and can effectively attenuate waves. The warm electron population overall experiences net energy loss and anisotropy drop while moving along the diffusion surfaces towards regions of lower phase space density, while the cool electron population undergoes heating when the waves grow, suggesting the cross-population interactions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1992

Instantaneous response of elastic thin-walled structures with arbitrary open cross section to rapid heating

A generalized modeling and analysis approach of thermally-induced coupled vibrations of elastic thin-walled configurations with arbitrary open cross sections are presented in conjunction with a unified implicit transient methodology. Limited research appears in literature which takes into account the influence of rapid thermal heating effects on structures involving various forms of coupling. As a consequence, the dynamic response of such thin-walled structures of arbitrary open cross section due to rapid heating are described here. Effects involving triple, double, and no coupling between bending and torsional vibrations caused by sudden heating on these structures are examined. Numerical test cases are presented which describe the influence of sudden heating on elastic thin-walled structures of arbitrary open cross sections.

Chen, Xiaoqin↗
NASA NTRS1992

Test and analysis results for composite transport fuselage and wing structures

Automated tow placement (ATP) and stitching of dry textile composite preforms followed by resin transfer molding (RTM) are being investigated by researchers at NASA LaRC and Douglas Aircraft Company as cost-effective manufacturing processes for obtaining damage tolerant fuselage and wing structures for transport aircraft. The Douglas work is being performed under a NASA contract entitled 'Innovative Composites Aircraft Primary Structures (ICAPS)'. Data are presented in this paper to assess the damage tolerance of ATP and RTM fuselage elements with stitched-on stiffeners from compression tests of impacted three-J-stiffened panels and from stiffener pull-off tests. Data are also presented to assess the damage tolerance of RTM wing elements which had stitched skin and stiffeners from impacted single stiffener and three blade-stiffened compression tests and stiffener pull-off tests.

Deaton, Jerry W.↗
NASA NTRS1992

Recession of FEP specimens from trays D11 and B7

We report work done at Boeing Defense and Space Group on analysis of silvered teflon specimens taken from selected locations of the Long Duration Exposure Facility under support from a contract provided by NASA LaRC. The samples discussed in this presentation were taken from the unexposed side of D11 and extended through the folded area of this blanket into the exposed area. Two similar areas were cut from blanket B7, one from the edge of the blanket near row six and one from the edge of the blanket near row eight and within a few centimeters of the copper grounding strap for B7. The specimens were each divided into three sections by cutting with a scapel. Two of the sections were mounted in a potting compound, which was cut and polished such that the cross-sectional thickness of each was exposed. One piece was mounted straight and the other was mounted in an attempt to configure the specimens such that it was bent with a radius of curvature similar to the on-orbit configuration. The third portion of each specimen was used for SEM images to help define the angle of exposure with respect to the ram at each location on the specimen. Photomicrographs were taken in cross section from the edge of the blanket through the curved transition region into the exposed area of the blanket. The thickness of the Fluorinated Ethylene Propylene (FEP) layer was determined at known distances from the edge of the blanket. SEM images were obtained at known distances to help define the angle with respect to ram and therefore establish the atomic oxygen fluence on each location and correlate this exposure with thickness. Thickness measurements made with a two to three centimeter distance minimized the uncertainty arising from variations in the as-manufactured thickness of each blanket. The nominal angle from ram of the exposed portion of each blanket, and the fact that the unexposed edge portions are approximately at right angles to the exposed portion were also used to help define the angles. Thickness measurements were taken at specified locations. An average thickness for the unexposed portion of the blanket was determined. Changes in thickness were then determined by difference.

Pippin, H. Gary↗
DOE OSTI2020

Well-to-Wheels Analysis of Zero-Emission Plug-In Battery Electric Vehicle Technology for Medium- and Heavy-Duty Trucks

Conventional diesel medium- and heavy-duty vehicles (MHDVs) create large amount of air emissions. With the advancement in technology and reduction in the cost of batteries, plug-in battery electric vehicles (BEVs) are increasingly attractive options for improving energy efficiency and reducing air emissions of MHDVs. In this paper, we compared the well-to-wheels (WTW) greenhouse gases (GHGs) and criteria air pollutant emissions of MHD BEVs with their conventional diesel counterparts across weight classes and vocations. We expanded the Greenhouse gases, Regulated Emissions, and Energy use in Technologies (GREET) model to conduct the WTW analysis of MHDVs. The fuel economy for a wide range of MHDV weight classes and vocations, over various driving cycles, was evaluated using a high-fidelity vehicle dynamic simulation software (Autonomie). The environmental impacts of MHD BEVs are sensitive to the source of electricity used to recharge their batteries. The WTW results show that MHD BEVs significantly improve environmental sustainability of MHDVs by providing deep reductions in WTW GHGs, nitrogen oxides, volatile organic compounds, and carbon monoxide emissions, compared to conventional diesel counterparts. Increasing shares of renewable and natural gas technologies in future national and regional electricity generation are expected to reduce WTW particulate matters and sulfur oxide emissions for further improvement of the environmental performance of MHD BEVs.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Passive spiral galaxies deeply captured by Subaru Hyper Suprime-Cam

Abstract This paper presents a thousand passive spiral galaxy samples at z = 0.01–0.3 based on a combined analysis of the Third Public Data Release of the Hyper Suprime-Cam Subaru Strategic Program (HSC-SSP PDR3) and the GALEX–SDSS–WISE Legacy Catalog (GSWLC-2). Among 54871 gri galaxy cutouts taken from the HSC-SSP PDR3 over 1072 deg2, we conducted a search with deep-learning morphological classification for candidates of passive spirals below the star-forming main sequence derived by ultraviolet to mid-infrared spectral energy distribution fitting in the GSWLC-2. We then classified the candidates into 1100 passive spirals and 1141 secondary samples based on visual inspections. Most of the latter cases are considered to be passive ringed S0 or pseudo-ringed galaxies. The remaining secondary samples have ambiguous morphologies, including two peculiar objects with diamond-shaped stellar wings. The selected passive spirals have a similar distribution to the general quiescent galaxies on the EWHδ–Dn4000 diagram and concentration indices. Moreover, we detected an enhanced passive fraction of spiral galaxies in X-ray clusters. Passive spirals in galaxy clusters are preferentially located in the midterm or late infall phase on the phase–space diagram, supporting the ram pressure scenario, which has been widely advocated in previous studies. The source catalog and gri-composite images are available on the HSC-SSP PDR3 website 〈https://hsc.mtk.nao.ac.jp/ssp/data-release/〉. Future updates, including integration with a citizen science project dedicated to the HSC data, will achieve more effective and comprehensive classifications.

Shimakawa, Rhythm (ORCID:0000000344422750)↗