Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Microstructure and temperature coefficient of resistance of thin cermet resistor films deposited from CrSi{sub 2}-Cr-SiC targets by S-gun magnetron

Technological solutions for producing nanoscale cermet resistor films with sheet resistances above 1000 {Omega}/{open_square} and low temperature coefficients of resistance (TCR) have been investigated. 2-40 nm thick cermet films were sputter deposited from CrSi{sub 2}-Cr-SiC targets by a dual cathode dc S-gun magnetron. In addition to studying film resistance versus temperature, the nanofilm structural features and composition were analyzed using scanning electron microscopy, atomic force microscopy, high-resolution transmission electron microscopy, energy-dispersive x-ray spectroscopy, and electron energy loss spectroscopy. This study has revealed that all cermet resistor films deposited at ambient and elevated temperatures were amorphous. The atomic ratio of Si to Cr in these films was about 2 to 1. The film TCR displayed a significant increase when the deposited film thickness was reduced below 2.5 nm. An optimized sputter process consisting of wafer degassing, cermet film deposition at elevated temperature with rf substrate bias, and a double annealing in vacuum, consisting of in situ annealing following the film sputtering and an additional annealing following the exposure of the wafers to air, has been found to be very effective for the film thermal stabilization and for fine tuning the film TCR. Cermet films with thicknesses in the range of 2.5-4 nm deposited using this technique had sheet resistances ranging from 1800 to 1200 {Omega}/{open_square} and TCR values from -50 ppm/ deg. C to near zero, respectively. A possible mechanism responsible for the high efficiency of annealing the cermet films in vacuum (after preliminary exposure to air), resulting in resistance stabilization and TCR reduction, is also discussed.

36 MATERIALS SCIENCE↗

In situ plasma diagnostics study of a commercial high-power hollow cathode magnetron deposition tool

Using a newly designed and built plasma diagnostic system, the plasma parameters were investigated on a commercial 200 mm high-power hollow cathode magnetron (HCM) physical vapor deposition tool using Ta target under argon plasma. A three dimensional (3D) scanning radio frequency (rf)-compensated Langmuir probe was constructed to measure the spatial distribution of the electron temperature (T{sub e}) and electron density (n{sub e}) in the substrate region of the HCM tool at various input powers (2-15 kW) and pressures (10-70 mTorr). The T{sub e} was in the range of 1-3 eV, scaling with decreasing power and decreasing pressure. Meanwhile, n{sub e} was in the range of 4x10{sup 10}-1x10{sup 12} cm{sup -3} scaling with increasing power and decreasing pressure. As metal deposits on the probe during the probe measurements, a self-cleaning plasma cup was designed and installed in the chamber to clean the tungsten probe tip. However, its effectiveness in recovering the measured plasma parameters was hindered by the metal layer deposited on the insulating probe tube which was accounted for the variation in the plasma measurements. Using a quartz crystal microbalance combined with electrostatic filters, the ionization fraction of the metal flux was measured at various input power of 2-16 kW and pressure of 5-40 mTorr. The metal ionization fraction reduced significantly with the increasing input power and decreasing gas pressure which were attributed to the corresponding variation in the ionization cross section and the residence time of the sputtered atoms in the plasma, respectively. Both the metal neutral and ion flux increased at higher power and lower pressure. The 3D measurements further showed that the ionization fraction decreased when moving up from the substrate to the cathode.

74 ATOMIC AND MOLECULAR PHYSICS↗

Coexistence of epitaxial Ta(111) and Ta(110) oriented magnetron sputtered thin film on c-cut sapphire

Epitaxial Ta films were grown on c-cut and r-cut sapphire substrates using magnetron sputtering. X-ray diffraction measurements indicate that the Ta films grown on c-cut sapphire substrates have two different crystal orientations. Low vacuum base pressure produced films with the (111) plane parallel to the basal plane after an initial (110) plane growth phase, whereas high base pressure resulted in the growth of (110) plane parallel to the basal plane with three azimuthally oriented domains coexisting. The superconducting critical temperatures T{sub c} of the films grown on c-cut substrates were found to be slightly higher than those for the films grown on r-cut substrates. The x-ray photoelectron spectroscopic data show oxygen content in the high vacuum base pressure deposited films and a difference in the valance band with different Ta surface planes.

36 MATERIALS SCIENCE↗

Spatial distribution of electrical properties for Al-doped ZnO films deposited by dc magnetron sputtering using various inert gases

Spatial distribution of electrical properties of Al-doped ZnO (AZO) films deposited by magnetron sputtering was investigated. To adjust the intensity of bombardment by high-energy particles, the AZO films were deposited using Ar, Kr, or Xe gas with varying plasma impedance. The spatial distribution of the electrical properties clearly depends on the sputtering gas. In the case of using Kr or Xe, the resistivity of the films in front of the target center and erosion areas was significantly enhanced, in contrast with Ar. This was attributed to an enhancement in bombardment damage due to the increased sputtering voltages required for Kr or Xe discharges. The increase in plasma impedance was due to the smaller coefficients for secondary-electron emission of the target surface by Kr or Xe impingements, which leads to the larger sputtering voltage.

36 MATERIALS SCIENCE↗

Combinatorial characterization of transparent conductive properties of Ga-doped ZnO films cosputtered from electron cyclotron resonance and rf magnetron plasma sources

The simultaneous sputtering of ZnO and Ga{sub 2}O{sub 3} by electron cyclotron resonance and rf magnetron plasma sources produced Ga-doped ZnO (GZO) films with continuously varying Ga concentration over the substrate surface. Combinatorial evaluation of electrical and optical properties of GZO film grown on silica glass substrate without heater annealing enabled identification of minimum resistivity (0.5 m{Omega} cm) at a Ga{sub 2}O{sub 3} content of 5.5 wt % with an optical transmittance of 90% in the visible wavelength. The monotonically decreasing mobility that was associated with increasing carrier concentration as Ga{sub 2}O{sub 3} content was increased indicated that conduction was governed by ionized impurity scattering. Above the critical Ga{sub 2}O{sub 3} content (6 wt %), carrier concentration decreased since excess Ga atoms that were incorporated beyond the solubility limit at Zn sites hindered large crystalline domains from forming. The ZnO (002) x-ray diffraction peak was suppressed and peaks assigned to Ga{sub 2}O{sub 3} were observed at high Ga{sub 2}O{sub 3} content. The optimum Ga{sub 2}O{sub 3} content shifted to 3.5 wt % at a deposition temperature of 200 deg. C and 2.5 wt % at 300 deg. C, and the minimum resistivity was further decreased to 0.28 m{Omega} cm at 200 deg. C. However, the resistivities at these elevated temperatures were incredibly high both at the lower and higher side of the optimum Ga{sub 2}O{sub 3} content.

36 MATERIALS SCIENCE↗

Plasma kinetics of Ar/O{sub 2} magnetron discharge by two-dimensional multifluid modeling

Multifluid two-dimensional model was developed to describe the plasma kinetics of the direct current Ar/O{sub 2} magnetron, coupling two modules: charged particles and neutrals. The first module deals with three positive ions - Ar{sup +}, O{sub 2}{sup +}, and O{sup +} - and two negative species - e{sup -} and O{sup -} - treated by the moments of Boltzmann's equation. The second one follows seven neutral species (Ar, O{sub 2}, O, O{sub 3}, and related metastables) by the multicomponent diffusion technique. The two modules are self-consistently coupled by the mass conservation and kinetic coefficients taking into account more than 100 volume reactions. The steady state is obtained when the overall convergence is achieved. Calculations for 10%O{sub 2} in Ar/O{sub 2} mixture at 2.67 and 4 Pa show that the oxygen excited species are mainly created by electron collisions in the negative glow of the discharge. Decreasing the pressure down to 0.67 Pa, the model reveals the nonlocal behavior of the reactive species. The density gradient of O{sub 2} ground state is reversed with respect to all gradients of the other reactive species, since the latter ones originate from the molecular ground state of oxygen. It is also found that the wall reactions drastically modify the space gradient of neutral reactive species, at least as much as the pressure, even if the discharge operates in compound mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spatial resistivity distribution of transparent conducting impurity-doped ZnO thin films deposited on substrates by dc magnetron sputtering

In transparent conducting impurity-doped ZnO thin films prepared by a conventional dc magnetron sputtering deposition (dc-MSD), the key factors in the deposition conditions that are necessary for practical use in transparent electrode applications were investigated. It was found that impurity-doped ZnO targets with a resistivity higher than approximately 3 m{Omega} cm are unsuitable for practical use in the preparation of transparent conducting Al-doped ZnO and Ga-doped ZnO thin films by conventional dc-MSD. Improvements of both the resulting resistivity distribution and resistivity can be sufficiently obtained only by using targets with a resistivity lower than about 0.5 m{Omega} cm. Using a low oxygen content target having a lower resistivity was found to reduce both the amount of oxygen in the chamber and the amount of oxygen reaching the substrate surface. As a result, it was demonstrated that sintered impurity-doped ZnO targets optimized for the preparation of thin films with lower resistivity as well as more uniform resistivity distribution on the substrate surface tended to exhibit a resistivity lower than about 0.5 m{Omega} cm.

36 MATERIALS SCIENCE↗

Morphology of TiN thin films grown on MgO(001) by reactive dc magnetron sputtering

Thin TiN films were grown by reactive dc magnetron sputtering on single-crystalline MgO(001) substrates at a range of temperatures from room temperature to 600 deg. C. Structural characterization was carried out using x-ray diffraction and reflection methods. TiN films grow epitaxially on the MgO substrates at growth temperatures of 200 deg. C and above. The crystal coherence length determined from Laue oscillations and the Scherrer method agrees with x-ray reflection thickness measurements to 6% and within 3% for growth temperatures of 200 and 600 deg. C, respectively. For lower growth temperatures the films are polycrystalline but highly textured and porous.

36 MATERIALS SCIENCE↗

Electrical and optical properties of Nb-doped TiO{sub 2} films deposited by dc magnetron sputtering using slightly reduced Nb-doped TiO{sub 2-x} ceramic targets

Nb-doped anatase TiO{sub 2} films were deposited on unheated glass by dc magnetron sputtering using slightly reduced Nb-doped TiO{sub 2-x} targets (Nb concentration: 3.7 and 9.5 at. %) with various hydrogen or oxygen flow ratios. After postannealing in a vacuum (6x10{sup -4} Pa) at 500 deg. C for 1 h, both films were crystallized into the polycrystalline anatase TiO{sub 2} structure. The resistivity decreased from 1.6x10{sup -3} to 6.3x10{sup -4} {Omega} cm with increasing Nb concentration from 2.8 to 8.0 at. %, where the carrier density increased from 5.4x10{sup 20} to 2.0x10{sup 21} cm{sup -3} and the Hall mobility was almost constant at 5-7 cm{sup 2} V{sup -1} s{sup -1}. The films exhibited a high transparency of over 60%-80% in the visible region.

36 MATERIALS SCIENCE↗

Residual stress stability in fiber textured stoichiometric AlN film grown using rf magnetron sputtering

The authors report on the stability of mechanical stress with aging and thermal cycling for columnar structured stoichiometric and homogeneous aluminum nitride thin films grown using radio frequency magnetron sputtering technique. The set of deposition parameters were optimized for the best possible orientation of crystallites in the c axis of compositionally stoichiometric films. The as-grown stress in the slightly nitrogen-rich film does not change when exposed to the atmosphere following deposition, while that in the nitrogen-deficient film, it changes due to oxidation. Additionally, the magnitude of as-grown stress has been found to depend on the substrate material in addition to the deposition parameters. The stress in the film grown on a Si(001) substrate was more tensile than in the film grown on a semi-insulating (si) GaAs(001) substrate for a given set of deposition parameters. Furthermore, the stress in the film grown on Si decreased with temperature, while that on si GaAs increased, indicating the thermally induced stress component to be the major component in the residual stress. Upon subsequent cooling the stress changes in both substrates followed the same path as of heating, thus exhibiting no hysteresis with thermal cycles between room temperature and 400 deg. C.

36 MATERIALS SCIENCE↗

Highly conductive indium zinc oxide prepared by reactive magnetron cosputtering technique using indium and zinc metallic targets

Zn-doped In{sub 2}O{sub 3} film is frequently deposited from an oxide target; but the use of metallic target is increasingly expected as preparing the film with comparable properties. This work aimed to prepare a highly conductive and transparent Zn-doped In{sub 2}O{sub 3} thin film on Corning Eagle{sup 2000} glass substrate by magnetron cosputtering method using indium and zinc targets. Structural characterization was performed using x-ray diffraction and x-ray photoelectron spectroscopy. The film had an amorphous structure when the film was prepared on an unheated substrate, but had an In{sub 2}O{sub 3} polycrystalline structure when the film was deposited on 150 and 300 deg. C substrates. The electrical properties of the film were greatly affected by annealing; the Zn-doped In{sub 2}O{sub 3} film had a low resistivity of 6.1x10{sup -4} {Omega} cm and an average transmittance of 81.7% when the film was deposited without substrate heating and followed a 600 deg. C annealing.

36 MATERIALS SCIENCE↗

Reactive magnetron cosputtering of hard and conductive ternary nitride thin films: Ti-Zr-N and Ti-Ta-N

Ternary transition metal nitride thin films, with thickness up to 300 nm, were deposited by dc reactive magnetron cosputtering in Ar-N{sub 2} plasma discharges at 300 deg. C on Si substrates. Two systems were comparatively studied, Ti-Zr-N and Ti-Ta-N, as representative of isostructural and nonisostructural prototypes, with the aim of characterizing their structural, mechanical, and electrical properties. While phase-separated TiN-ZrN and TiN-TaN are the bulk equilibrium states, Ti{sub 1-x}Zr{sub x}N and Ti{sub 1-y}Ta{sub y}N solid solutions with the Na-Cl (B1-type) structure could be stabilized in a large compositional range (up to x=1 and y=0.75, respectively). Substituting Ti atoms by either Zr or Ta atoms led to significant changes in film texture, microstructure, grain size, and surface morphology, as evidenced by x-ray diffraction, x-ray reflectivity, and scanning electron and atomic force microscopies. The ternary Ti{sub 1-y}Ta{sub y}N films exhibited superior mechanical properties to Ti{sub 1-x}Zr{sub x}N films as well as binary compounds, with hardness as high as 42 GPa for y=0.69. All films were metallic, the lowest electrical resistivity {rho}{approx}65 {mu}{Omega} cm being obtained for pure ZrN, while for Ti{sub 1-y}Ta{sub y}N films a minimum was observed at y{approx}0.3. The evolution of the different film properties is discussed based on microstructrural investigations.

36 MATERIALS SCIENCE↗

Investigation of microstructure, surface morphology, and hardness properties of PtIr films by magnetron sputtering

Pt{sub 1-x}Ir{sub x} films with x varying from 22.76 to 63.25 at. % are deposited on (100) Si wafer substrates at 400 deg. C by magnetron sputtering deposition. The effects of the Ir concentration on the microstructure, morphology, and hardness of PtIr films are investigated by field emission scanning electron microscopy, x-ray diffraction, atomic force microscopy, and nanoindentation system. The columnar structures are observed by field emission scanning electron microscopy. X-ray diffraction analysis reveals that PtIr films have preferred orientation along Pt(111) when the Ir concentration is below 50.84 at. %. When the Ir content is more than 50.84 at. %, the PtIr film shifts to another preferred orientation, Ir(111). The surface morphology is analyzed by atomic force microscopy. The roughness of the PtIr films decreases with increasing Ir content. The hardness of all the PtIr films is below 20 GPa. The maximum hardness of the PtIr films is about 14.9 GPa when the Ir concentration is 57.9 at. %.

36 MATERIALS SCIENCE↗

Formation of pyrite (FeS{sub 2}) thin films by thermal sulfurization of dc magnetron sputtered iron

Iron films deposited by direct current magnetron sputtering onto glass substrates were converted into FeS{sub 2} films by thermal sulfurization. Experiments were carried out to optimize the sulfurization process, and the formation of FeS{sub 2} thin films was investigated under different annealing temperatures and times. High quality FeS{sub 2} films were fabricated using this process, and single phase pyrite films were obtained after sulfurization in a sulfur and nitrogen atmosphere at 450 deg. C for 1 h. Film crystallinity and phase identification were determined by using x-ray diffraction. The cubic phase pyrite films prepared were p-type, and scanning electron microscopy studies exhibited a homogeneous surface of pyrite. The authors have found that the best Ohmic contact for their pyrite thin films, using inexpensive metals, was Ni. The following were chosen for the study: Al, Mo, Fe, and Ni, and the one that led to the lowest resistance, 333 {Omega}, was Ni.

36 MATERIALS SCIENCE↗

Comprehensive study of the p-type conductivity formation in radio frequency magnetron sputtered arsenic-doped ZnO film

Arsenic doped ZnO and ZnMgO films were deposited on SiO{sub 2} using radio frequency magnetron sputtering and ZnO-Zn{sub 3}As{sub 2} and ZnO-Zn{sub 3}As{sub 2}-MgO targets, respectively. It was found that thermal activation is required to activate the formation of p-type conductivity. Hall measurements showed that p-type films with a hole concentration of {approx}10{sup 17} cm{sup -3} and mobility of {approx}8 cm{sup 2} V{sup -1} s{sup -1} were obtained at substrate temperatures of 400-500 deg. C The shallow acceptor formation mechanism was investigated using x-ray photoelectron spectroscopy, positron annihilation, low temperature photoluminescence, and nuclear reaction analysis. The authors suggest that the thermal annealing activates the formation of the As{sub Zn}-2V{sub Zn} shallow acceptor complex and removes the compensating hydrogen center.

36 MATERIALS SCIENCE↗

DC reactive magnetron sputtering, annealing, and characterization of CuAlO{sub 2} thin films

CuAlO{sub x} thin films were prepared at three substrate temperatures (T{sub S}=60, 300, and 600 deg. C) and two oxygen partial pressures (P{sub O{sub 2}}=0.5 and 2 mTorr) via dc reactive magnetron sputtering from Cu-Al 50-50 at. % alloy targets and subsequent annealing. As-deposited films with P{sub O{sub 2}}=0.5 mTorr were oxygen deficient; although the delafossite structure formed upon annealing, electrical properties were poor. Films deposited with P{sub O{sub 2}}=2 mTorr transformed into the delafossite structure and exhibited p-type conductivity after annealing under N{sub 2} at temperatures T{sub A}{>=}750 deg. C. Conductivity generally increased with increasing T{sub S} and decreasing T{sub A}. A special case of P{sub O{sub 2}}=2 mTorr and low T{sub S} (60 deg. C) resulted in a partially crystalline oxide phase that transformed into the delafossite structure at T{sub A}=700 deg. C and yielded the highest conductivity of 1.8 S cm{sup -1}. In general, a T{sub A} near the phase formation boundary led to an increase in conductivity. Low-temperature hydrothermal annealing was also investigated and shown to produce mixed phase films exhibiting the delafossite structure along with CuO, AlOOH, and Al{sub 2}O{sub 3}.

36 MATERIALS SCIENCE↗

Spectroscopic ellipsometry and x-ray photoelectron spectroscopy of La{sub 2}O{sub 3} thin films deposited by reactive magnetron sputtering

Lanthanum oxide (La{sub 2}O{sub 3}) films were grown by the reactive dc magnetron sputtering and studied their structural, chemical and optical parameters. La{sub 2}O{sub 3} films were deposited onto Si substrates by sputtering La-metal in a reactive gas (Ar+O{sub 2}) mixture at a substrate temperature of 200 deg. C Reflection high-energy electron diffraction measurements confirm the amorphous state of La{sub 2}O{sub 3} films. Chemical analysis of the top-surface layers evaluated with x-ray photoelectron spectroscopy indicates the presence of a layer modified by hydroxylation due to interaction with atmosphere. Optical parameters of a-La{sub 2}O{sub 3} were determined with spectroscopic ellipsometry (SE). There is no optical absorption over spectral range {lambda}=250-1100 nm. Dispersion of refractive index of a-La{sub 2}O{sub 3} was defined by fitting of SE parameters over {lambda}=250-1100 nm.

36 MATERIALS SCIENCE↗

Highly textured growth of AlN films on sapphire by magnetron sputtering for high temperature surface acoustic wave applications

Piezoelectric aluminum nitride films were deposited onto 3 in. [0001] sapphire substrates by reactive magnetron sputtering to explore the possibility of making highly (002)-textured AlN films to be used in surface acoustic wave (SAW) devices for high temperature applications. The synthesized films, typically 1 {mu}m thick, exhibited a columnar microstructure and a high c-axis texture. The relationship between the microstructures and process conditions was examined by x-ray diffraction (XRD), transmission electron microscopy, and atomic force microscopy analyses. The authors found that highly (002)-textured AlN films with a full width at half maximum of the rocking curve of less than 0.3 deg. can be achieved under high nitrogen concentration and moderate growth temperature, i.e., 250 deg. C. The phi-scan XRD reveals the high in-plane texture of deposited AlN films. The SAW devices, based on the optimized AlN films on sapphire substrate, were characterized before and after an air annealing process at 800 deg. C for 90 min. The frequency response, recorded after the annealing process, confirmed that the thin films were still strong in a high temperature environment and that they had retained their piezoelectric properties.

36 MATERIALS SCIENCE↗