Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Combinatorial Deposition of Ultrathick Ta-W-Au-Bi High-Entropy Alloys for Next-Generation Hohlraums by Direct-Current Magnetron Sputtering

Hohlraum temperature calculations with the model by J. H. Hammer and M. D. Rosen predict a higher X-ray drive from Ta-W-Au-Bi high-entropy alloys compared to pure Au and recently developed Ta 4 Au and Au-Bi hohlraums. Here, we study the microstructure and properties of 25-75−µm-thick Ta-W-Au-Bi alloy films deposited via combinatorial direct-current magnetron sputtering. All of the films have promising physical properties, including high electrical resistivity, that satisfy the requirements for magnetically assisted inertial confinement fusion experiments. While porosity tends to increase with increasing Bi content, we also found that films with Bi content > 44 at. % exhibited densification close to the substrate/film interface and formed a single-phase alloy. In conclusion, these findings provide a potential path forward for the development of Ta-W-Au-Bi alloys for next-generation hohlraum materials.

Magnetron sputtering↗

Distance-dependent plasma composition and ion energy in high power impulse magnetron sputtering

The plasma composition of high power impulse magnetron sputtering (HIPIMS) has been studied for titanium and chromium targets using a combined energy analyser and quadrupole mass spectrometer. Measurements were done at distances from 50 to 300 mm from the sputtering target. Ti and Cr are similar in atomic mass but have significantly different sputter yields, which gives interesting clues on the effect of the target on plasma generation and transport of atoms. The Ti and Cr HIPIMS plasmas operated at a peak target current density of ~;;0.5 A cm-2. The measurements of the argon and metal ion content as well as the ion energy distribution functions showed that (1) singly and doubly charged ions were found for argon as well as for the target metal, (2) the majority of ions were singly charged argon for both metals at all distances investigated, (3) the Cr ion density was maintained to distances further from the target than Ti. Gas rarefaction was identified as a main factor promoting transport of metal ions, with the stronger effect observed for Cr, the material with higher sputter yield. Cr ions were found to displace a significant portion of the gas ions, whereas this was less evident in the Ti case. The observations indicate that the presence of metal vapour promotes charge exchange and reduces the electron temperature and thereby practically prevents the production of Ar2+ ions near the target. The content of higher charge states of metal ions depends on the probability of charge exchange with argon.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Rotating spokes, potential hump and modulated ionization in radio frequency magnetron discharges

Here, in this work, the transition from the gradient drift instability (GDI) into an m = 1 rotating spoke in the radio frequency magnetron discharge was studied by means of the two-dimensional axial-azimuthal (z–y) particle-in-cell/Monte Carlo collision method. The kinetic model combined with the linear analysis of the perturbation revealed that the cathode sheath (axial) electric field E z triggers the GDI, deforming the local potential until the instability condition is not fulfilled and the fluctuation growth stops in which moment the instability becomes saturated. The potential deformation consequently leads to the formation of the potential hump, surrounding which the azimuthal electric field E y is present. The saturation level of E y was found to be synchronized with and proportional to the time-changing voltage applied at the cathode, resulting in the RF-modulation of the electron heating in the E y due to $\nabla B$ drift. In the saturated stage of the instability, it was shown that the rotation velocity and direction of the spoke present in the simulations agree well with the experimental observation (Panjan 2019 J. Appl. Phys.125 203303). In the instability linear stage, the instability mode wavelength and the growth rate were also found to be in good agreement with the prediction of the GDI linear fluid theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Coherent High-Frequency Axial Oscillations in a Partially Magnetized Direct Current Magnetron Discharge

High-frequency oscillations are observed in a neon plasma of a direct current magnetron discharge. At low discharge currents, we see highly coherent 60 MHz fluctuations. Above a distinct current threshold, secondary 5–10 MHz fluctuations emerge in addition to turbulent fluctuations in the 60–100 MHz range. The oscillations in the total discharge current suggest axial wave propagation. A lower-hybrid wave theory is invoked to model the high-frequency oscillations. Here, we attribute the low-frequency modes to a turbulence-driven inverse cascade process, as suggested by recent simulations.

33 ADVANCED PROPULSION SYSTEMS↗

Design and analysis of magnetic coil for relativistic magnetron

This paper presents the design of magnetic coil for relativistic magnetron (RM) for LIA (Linear Induction Accelerator)-400 systems. Vacuum improves the efficiency of RM for HPM generation. Magnetic field in RM is very critical parameter and should be nearly constant in the active region. Typical coils are helical in nature, which have multi turns of varying radius. Magnetic field calculation of such coils with basic equations of Helmholtz coils or solenoid with mean radius can only give estimation. Field computational softwares like CST require small mesh size and boundary at very far so consume large memory and take very much time. Helical coils are simplified such that the basic law of magnetic field calculation i.e. Bio-Savart law can be applied with less complexity. Pairs of spiral coils have been analyzed for magnetic field and Lorenz's force. The approach is field experimentally validated. (author)

43 PARTICLE ACCELERATORS↗

Implementation and initial test result of a prototype solid state modulator for pulsed magnetron

A solid-state modulator rated for 50 kV, 120A, 4μs and 250 Hz has been designed. The discharging circuit of the modulator is being tested at ∼ 33 kV, 40-80A, at a maximum pulse repetition rate of 30 pps. The paper discusses development and testing of prototype discharging circuit on resistive load and magnetron. The technique used for measurement of pulse transformer leakage inductance, distributed capacitance and stray primary circuit series inductance will also be discussed in detail. It is necessary to have Energy Storage Capacitors with low ESL for these applications (ESL < 40 nH). The method used for evaluating the ESL of locally available metalized polypropylene capacitors will also be presented. (author)

43 PARTICLE ACCELERATORS↗

Magnetron sputtered Si-B-C-N films with high oxidation resistance and thermal stability in air at temperatures above 1500 deg. C

Novel quaternary Si-B-C-N materials are becoming increasingly attractive because of their possible high-temperature and harsh-environment applications. In the present work, amorphous Si-B-C-N films were deposited on Si and SiC substrates by reactive dc magnetron cosputtering using a single C-Si-B or B{sub 4}C-Si target in nitrogen-argon gas mixtures. A fixed 75% Si fraction in the target erosion areas, a rf induced negative substrate bias voltage of -100 V, a substrate temperature of 350 deg. C, and a total pressure of 0.5 Pa were used in the depositions. The corresponding discharge and deposition characteristics (such as the ion-to-film-forming particle flux ratio, ion energy per deposited atom, and deposition rate) are presented to understand complex relationships between process parameters and film characteristics. Films deposited under optimized conditions (B{sub 4}C-Si target, 50% N{sub 2}+50% Ar gas mixture), possessing a composition (in at. %) Si{sub 32-34}B{sub 9-10}C{sub 2-4}N{sub 49-51} with a low (less than 5 at. %) total content of hydrogen and oxygen, exhibited extremely high oxidation resistance in air at elevated temperatures (even above 1500 deg. C). Formation of protective surface layers (mainly composed of Si and O) was proved by high-resolution transmission electron microscopy, Rutherford backscattering spectrometry, and x-ray diffraction measurements after oxidization. Amorphous structure of the Si-B-C-N films was maintained under the oxidized surface layers after annealing in air up to 1700 deg. C (a limit imposed by thermogravimetric analysis in oxidative atmospheres)

36 MATERIALS SCIENCE↗

Growth and characterization of TiAlN/CrAlN superlattices prepared by reactive direct current magnetron sputtering

TiAlN and CrAlN coatings were prepared using a reactive direct current magnetron sputtering system from TiAl and CrAl targets. Structural characterization of the coatings using x-ray diffraction (XRD) revealed the B1 NaCl structure of TiAlN and CrAlN coatings with a prominent reflection along the (111) plane. The XPS data confirmed the bonding structures of TiAlN and CrAlN single layer coatings. Subsequently, nanolayered multilayer coatings of TiAlN/CrAlN were deposited on silicon and mild steel (MS) substrates at different modulation wavelengths ({lambda}) with a total thickness of approximately 1.0 {mu}m. The modulation wavelengths were calculated from the x-ray reflectivity data using modified Bragg's law. TiAlN/CrAlN multilayer coatings were textured along (111) for {lambda}<200 A and the XRD patterns showed the formation of superlattice structure for coatings deposited at {lambda}=102 A. The x-ray reflectivity data showed reflections of fifth and seventh orders for multilayer coatings deposited at {lambda}=102 and 138 A, respectively, indicating the formation of sharp interfaces between TiAlN and CrAlN layers. The cross-sectional scanning electron microscopy image of TiAlN/CrAlN multilayer coatings indicated a noncolumnar and dense microstructure. A maximum hardness of 39 GPa was observed for TiAlN/CrAlN multilayer coatings deposited at {lambda}=93 A, which was higher than the rule-of-mixture value (30 GPa) for TiAlN and CrAlN. Study of thermal stability of the coatings in air using micro-Raman spectroscopy indicated that the TiAlN/CrAlN multilayer coatings were stable up to 900 deg. C in air. TiAlN/CrAlN multilayer coatings also exhibited improved corrosion resistance when compared to the MS substrate.

36 MATERIALS SCIENCE↗

Photoluminescence from Er-doped Si-rich Si oxides deposited by magnetron sputtering in Ar or Ar+H{sub 2} plasmas

The authors have studied photoluminescence (PL) from Er-doped Si-rich Si oxide (SRSO) films deposited by magnetron sputtering of an Er+Si+SiO{sub 2} composite target in Ar or Ar+H{sub 2} ambients. When the samples were annealed in N{sub 2}, for the film grown in an Ar ambient, the PL annealing behaviors reveal that the emissions from the film are defect-related and that the Er{sup 3+} PL at 1.54 {mu}m is possibly triggered by a defect-mediated energy transfer process; while for the films grown in an Ar+H{sub 2} ambient, the emissions from the SRSO matrix are suppressed and the Er PL intensities increase significantly but differently dependent on the Ar:H{sub 2} ratios during sputtering. After annealing the samples in an Ar+5%H{sub 2} (FG) ambient, however, almost no Er PL was observed from the film grown in the Ar ambient, while the Er PL intensities of the films grown in the Ar+H{sub 2} ambient increase further compared to those annealed in N{sub 2}. Fourier transform infrared spectroscopy shows that the absorption of the samples after FG annealing is weaker than after annealing in N{sub 2}. The PL properties have also been compared to those of a sample grown by plasma enhanced chemical vapor deposition. The roles of hydrogen during sputtering and postdeposition annealing are discussed.

36 MATERIALS SCIENCE↗

Effect of pulse frequency on the ion fluxes during pulsed dc magnetron sputtering

The ion fluxes and energies which impinge on the substrate during the deposition of chromium nitride by asymmetric bipolar pulsed dc reactive magnetron sputtering have been analyzed using energy resolved mass spectrometry. It has been found that there is a remarkable increase in ion flux at higher pulse frequencies and that the peak ion energy is directly related to the positive voltage overshoot of the target voltage. The magnitude of the metal flux depositing on the substrate is consistent with a 'dead time' of {approx}0.7 {mu}s at the start of the on period. The variation of the ion flux with pulse frequency has been explained by a simple model in which the ion density during the on period has a large peak which is slightly delayed from the large negative voltage overshoot which occurs at the start of the on pulse due to increased ionization at that time. This is consistent with the previously observed phenomena in pulsed sputtering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructure and temperature coefficient of resistance of thin cermet resistor films deposited from CrSi{sub 2}-Cr-SiC targets by S-gun magnetron

Technological solutions for producing nanoscale cermet resistor films with sheet resistances above 1000 {Omega}/{open_square} and low temperature coefficients of resistance (TCR) have been investigated. 2-40 nm thick cermet films were sputter deposited from CrSi{sub 2}-Cr-SiC targets by a dual cathode dc S-gun magnetron. In addition to studying film resistance versus temperature, the nanofilm structural features and composition were analyzed using scanning electron microscopy, atomic force microscopy, high-resolution transmission electron microscopy, energy-dispersive x-ray spectroscopy, and electron energy loss spectroscopy. This study has revealed that all cermet resistor films deposited at ambient and elevated temperatures were amorphous. The atomic ratio of Si to Cr in these films was about 2 to 1. The film TCR displayed a significant increase when the deposited film thickness was reduced below 2.5 nm. An optimized sputter process consisting of wafer degassing, cermet film deposition at elevated temperature with rf substrate bias, and a double annealing in vacuum, consisting of in situ annealing following the film sputtering and an additional annealing following the exposure of the wafers to air, has been found to be very effective for the film thermal stabilization and for fine tuning the film TCR. Cermet films with thicknesses in the range of 2.5-4 nm deposited using this technique had sheet resistances ranging from 1800 to 1200 {Omega}/{open_square} and TCR values from -50 ppm/ deg. C to near zero, respectively. A possible mechanism responsible for the high efficiency of annealing the cermet films in vacuum (after preliminary exposure to air), resulting in resistance stabilization and TCR reduction, is also discussed.

36 MATERIALS SCIENCE↗

In situ plasma diagnostics study of a commercial high-power hollow cathode magnetron deposition tool

Using a newly designed and built plasma diagnostic system, the plasma parameters were investigated on a commercial 200 mm high-power hollow cathode magnetron (HCM) physical vapor deposition tool using Ta target under argon plasma. A three dimensional (3D) scanning radio frequency (rf)-compensated Langmuir probe was constructed to measure the spatial distribution of the electron temperature (T{sub e}) and electron density (n{sub e}) in the substrate region of the HCM tool at various input powers (2-15 kW) and pressures (10-70 mTorr). The T{sub e} was in the range of 1-3 eV, scaling with decreasing power and decreasing pressure. Meanwhile, n{sub e} was in the range of 4x10{sup 10}-1x10{sup 12} cm{sup -3} scaling with increasing power and decreasing pressure. As metal deposits on the probe during the probe measurements, a self-cleaning plasma cup was designed and installed in the chamber to clean the tungsten probe tip. However, its effectiveness in recovering the measured plasma parameters was hindered by the metal layer deposited on the insulating probe tube which was accounted for the variation in the plasma measurements. Using a quartz crystal microbalance combined with electrostatic filters, the ionization fraction of the metal flux was measured at various input power of 2-16 kW and pressure of 5-40 mTorr. The metal ionization fraction reduced significantly with the increasing input power and decreasing gas pressure which were attributed to the corresponding variation in the ionization cross section and the residence time of the sputtered atoms in the plasma, respectively. Both the metal neutral and ion flux increased at higher power and lower pressure. The 3D measurements further showed that the ionization fraction decreased when moving up from the substrate to the cathode.

74 ATOMIC AND MOLECULAR PHYSICS↗

Coexistence of epitaxial Ta(111) and Ta(110) oriented magnetron sputtered thin film on c-cut sapphire

Epitaxial Ta films were grown on c-cut and r-cut sapphire substrates using magnetron sputtering. X-ray diffraction measurements indicate that the Ta films grown on c-cut sapphire substrates have two different crystal orientations. Low vacuum base pressure produced films with the (111) plane parallel to the basal plane after an initial (110) plane growth phase, whereas high base pressure resulted in the growth of (110) plane parallel to the basal plane with three azimuthally oriented domains coexisting. The superconducting critical temperatures T{sub c} of the films grown on c-cut substrates were found to be slightly higher than those for the films grown on r-cut substrates. The x-ray photoelectron spectroscopic data show oxygen content in the high vacuum base pressure deposited films and a difference in the valance band with different Ta surface planes.

36 MATERIALS SCIENCE↗

Spatial distribution of electrical properties for Al-doped ZnO films deposited by dc magnetron sputtering using various inert gases

Spatial distribution of electrical properties of Al-doped ZnO (AZO) films deposited by magnetron sputtering was investigated. To adjust the intensity of bombardment by high-energy particles, the AZO films were deposited using Ar, Kr, or Xe gas with varying plasma impedance. The spatial distribution of the electrical properties clearly depends on the sputtering gas. In the case of using Kr or Xe, the resistivity of the films in front of the target center and erosion areas was significantly enhanced, in contrast with Ar. This was attributed to an enhancement in bombardment damage due to the increased sputtering voltages required for Kr or Xe discharges. The increase in plasma impedance was due to the smaller coefficients for secondary-electron emission of the target surface by Kr or Xe impingements, which leads to the larger sputtering voltage.

36 MATERIALS SCIENCE↗

Combinatorial characterization of transparent conductive properties of Ga-doped ZnO films cosputtered from electron cyclotron resonance and rf magnetron plasma sources

The simultaneous sputtering of ZnO and Ga{sub 2}O{sub 3} by electron cyclotron resonance and rf magnetron plasma sources produced Ga-doped ZnO (GZO) films with continuously varying Ga concentration over the substrate surface. Combinatorial evaluation of electrical and optical properties of GZO film grown on silica glass substrate without heater annealing enabled identification of minimum resistivity (0.5 m{Omega} cm) at a Ga{sub 2}O{sub 3} content of 5.5 wt % with an optical transmittance of 90% in the visible wavelength. The monotonically decreasing mobility that was associated with increasing carrier concentration as Ga{sub 2}O{sub 3} content was increased indicated that conduction was governed by ionized impurity scattering. Above the critical Ga{sub 2}O{sub 3} content (6 wt %), carrier concentration decreased since excess Ga atoms that were incorporated beyond the solubility limit at Zn sites hindered large crystalline domains from forming. The ZnO (002) x-ray diffraction peak was suppressed and peaks assigned to Ga{sub 2}O{sub 3} were observed at high Ga{sub 2}O{sub 3} content. The optimum Ga{sub 2}O{sub 3} content shifted to 3.5 wt % at a deposition temperature of 200 deg. C and 2.5 wt % at 300 deg. C, and the minimum resistivity was further decreased to 0.28 m{Omega} cm at 200 deg. C. However, the resistivities at these elevated temperatures were incredibly high both at the lower and higher side of the optimum Ga{sub 2}O{sub 3} content.

36 MATERIALS SCIENCE↗

Plasma kinetics of Ar/O{sub 2} magnetron discharge by two-dimensional multifluid modeling

Multifluid two-dimensional model was developed to describe the plasma kinetics of the direct current Ar/O{sub 2} magnetron, coupling two modules: charged particles and neutrals. The first module deals with three positive ions - Ar{sup +}, O{sub 2}{sup +}, and O{sup +} - and two negative species - e{sup -} and O{sup -} - treated by the moments of Boltzmann's equation. The second one follows seven neutral species (Ar, O{sub 2}, O, O{sub 3}, and related metastables) by the multicomponent diffusion technique. The two modules are self-consistently coupled by the mass conservation and kinetic coefficients taking into account more than 100 volume reactions. The steady state is obtained when the overall convergence is achieved. Calculations for 10%O{sub 2} in Ar/O{sub 2} mixture at 2.67 and 4 Pa show that the oxygen excited species are mainly created by electron collisions in the negative glow of the discharge. Decreasing the pressure down to 0.67 Pa, the model reveals the nonlocal behavior of the reactive species. The density gradient of O{sub 2} ground state is reversed with respect to all gradients of the other reactive species, since the latter ones originate from the molecular ground state of oxygen. It is also found that the wall reactions drastically modify the space gradient of neutral reactive species, at least as much as the pressure, even if the discharge operates in compound mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spatial resistivity distribution of transparent conducting impurity-doped ZnO thin films deposited on substrates by dc magnetron sputtering

In transparent conducting impurity-doped ZnO thin films prepared by a conventional dc magnetron sputtering deposition (dc-MSD), the key factors in the deposition conditions that are necessary for practical use in transparent electrode applications were investigated. It was found that impurity-doped ZnO targets with a resistivity higher than approximately 3 m{Omega} cm are unsuitable for practical use in the preparation of transparent conducting Al-doped ZnO and Ga-doped ZnO thin films by conventional dc-MSD. Improvements of both the resulting resistivity distribution and resistivity can be sufficiently obtained only by using targets with a resistivity lower than about 0.5 m{Omega} cm. Using a low oxygen content target having a lower resistivity was found to reduce both the amount of oxygen in the chamber and the amount of oxygen reaching the substrate surface. As a result, it was demonstrated that sintered impurity-doped ZnO targets optimized for the preparation of thin films with lower resistivity as well as more uniform resistivity distribution on the substrate surface tended to exhibit a resistivity lower than about 0.5 m{Omega} cm.

36 MATERIALS SCIENCE↗

Morphology of TiN thin films grown on MgO(001) by reactive dc magnetron sputtering

Thin TiN films were grown by reactive dc magnetron sputtering on single-crystalline MgO(001) substrates at a range of temperatures from room temperature to 600 deg. C. Structural characterization was carried out using x-ray diffraction and reflection methods. TiN films grow epitaxially on the MgO substrates at growth temperatures of 200 deg. C and above. The crystal coherence length determined from Laue oscillations and the Scherrer method agrees with x-ray reflection thickness measurements to 6% and within 3% for growth temperatures of 200 and 600 deg. C, respectively. For lower growth temperatures the films are polycrystalline but highly textured and porous.

36 MATERIALS SCIENCE↗