Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Low Reynolds Number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

The effects of leading-edge serrations on reducing flow unsteadiness about airfoils.

High frequency surface pressure measurements were obtained from wind-tunnel tests over the Reynolds number range 1.2 x 1,000,000 to 6.2 x 1,000,000 on a rectangular wing of NACA 63-009 airfoil section. A wide selection of leading-edge serrations were also added to the basic airfoil. Under a two-dimensional laminar bubble very close to the leading edge of the basic airfoil there is a large peak in rms pressure, which is interpreted as an oscillation in size and position of the bubble. The serrations divide the bubble into segments and reduce the peak rms pressures. A low Reynolds number flow visualization test on a hydrofoil in water was also conducted. A von Karman vortex street was found trailing from the rear of the foil. Its frequency is at a much lower Strouhal number than in the high Reynolds number experiment, and is related mathematically to the airfoil trailing-edge and boundary-layer thicknesses.

Schwind, R. G.↗
NASA NTRS1981

Aerodynamics, aeroelasticity, and stability of hang gliders. Experimental results

One-fifth-scale models of three basic ultralight glider designs were constructed to simulate the elastic properties of full scale gliders and were tested at Reynolds numbers close to full scale values. Twenty-four minor modifications were made to the basic configurations in order to evaluate the effects of twist, reflex, dihedral, and various stability enhancement devices. Longitudinal and lateral data were obtained at several speeds through an angle of attack range of -30 deg to +45 deg with sideslip angles of up to 20 deg. The importance of vertical center of gravity displacement is discussed. Lateral data indicate that effective dihedral is lost at low angles of attack for nearly all of the configurations tested. Drag data suggest that lift-dependent viscous drag is a large part of the glider's total drag as is expected for thin, cambered sections at these relatively low Reynolds numbers.

Kroo, I. M.↗
NASA NTRS1993

Regeneration of near-wall turbulence structures

An examination of the regeneration mechanisms of near-wall turbulence and an attempt to investigate the critical Reynolds number conjecture of Waleffe & Kim is presented. The basis is an extension of the 'minimal channel' approach of Jimenez and Moin which emphasizes the near-wall region and further reduces the complexity of the turbulent flow. Reduction of the flow Reynolds number to the minimum value which will allow turbulence to be sustained has the effect of reducing the ratio of the largest scales to the smallest scales or, equivalently, of causing the near-wall region to fill more of the area between the channel walls. In addition, since each wall may have an active near-wall region, half of the channel is always somewhat redundant. If a plane Couette flow is instead chosen as the base flow, this redundancy is eliminated: the mean shear of a plane Couette flow has a single sign, and at low Reynolds numbers, the two wall regions share a single set of structures. A minimal flow with these modifications possesses, by construction, the strongest constraints which allow sustained turbulence, producing a greatly simplified flow in which the regeneration process can be examined.

Hamilton, James M.↗
NASA NTRS1999

Premixed Turbulent Flame Propagation in Microgravity

A combined numerical-experimental study has been carried out to investigate the structure and propagation characteristics of turbulent premixed flames with and without the influence of buoyancy. Experimentally, the premixed flame characteristics are studied in the wrinkled regime using a Couette flow facility and an isotropic flow facility in order to resolve the scale of flame wrinkling. Both facilities were chosen for their ability to achieve sustained turbulence at low Reynolds number. This implies that conventional diagnostics can be employed to resolve the smallest scales of wrinkling. The Couette facility was also built keeping in mind the constraints imposed by the drop tower requirements. Results showed that the flow in this Couette flow facility achieves full-developed turbulence at low Re and all turbulence statistics are in good agreement with past measurements on large-scale facilities. Premixed flame propagation studies were then carried out both using the isotropic box and the Couette facility. Flame imaging showed that fine scales of wrinkling occurs during flame propagation. Both cases in Ig showed significant buoyancy effect. To demonstrate that micro-g can remove this buoyancy effect, a small drop tower was built and drop experiments were conducted using the isotropic box. Results using the Couette facility confirmed the ability to carry out these unique reacting flow experiments at least in 1g. Drop experiments at NASA GRC were planned but were not completed due to termination of this project.

Menon, Suresh↗
NASA NTRS2000

Towards LES Models of Jets and Plumes

As pointed out by Rodi standard integral solutions for jets and plumes developed for discharge into infinite, quiescent ambient are difficult to extend to complex situations, particularly in the presence of boundaries such as the sea floor or ocean surface. In such cases the assumption of similarity breaks down and it is impossible to find a suitable entrainment coefficient. The models are also incapable of describing any but the most slowly varying unsteady motions. There is therefore a need for full time-dependent modeling of the flow field for which there are three main approaches: (1) Reynolds averaged numerical simulation (RANS), (2) large eddy simulation (LES), and (3) direct numerical simulation (DNS). Rodi applied RANS modeling to both jets and plumes with considerable success, the test being a match with experimental data for time-averaged velocity and temperature profiles as well as turbulent kinetic energy and rms axial turbulent velocity fluctuations. This model still relies on empirical constants, some eleven in the case of the buoyant jet, and so would not be applicable to a partly laminar plume, may have limited use in the presence of boundaries, and would also be unsuitable if one is after details of the unsteady component of the flow (the turbulent eddies). At the other end of the scale DNS modeling includes all motions down to the viscous scales. Boersma et al. have built such a model for the non-buoyant case which also compares well with measured data for mean and turbulent velocity components. The model demonstrates its versatility by application to a laminar flow case. As its name implies, DNS directly models the Navier-Stokes equations without recourse to subgrid modeling so for flows with a broad spectrum of motions (high Re) the cost can be prohibitive - the number of required grid points scaling with Re(exp 9/4) and the number of time steps with Re(exp 3/4). The middle road is provided by LES whereby the Navier-Stokes equations are formally filtered with the filter chosen to only exclude the smallest turbulent motions. If successful, LES should provide much of the detail available to DNS but at more bearable cost. Fatica et al. in comparing LES with DNS for a low Reynolds number jet showed that the LES could simulate the temporally evolving behavior including growth of the jet thickness. It is the intention of this report to explore the application of an LES model to jets and plumes. As always, before tackling complex situations, the model must be tested for the simplest of cases and so we address only two, a non-buoyant axisymmetric jet issuing steadily from an orifice into a semi-infinite stationary environment and a buoyant jet in the same environment. The work is a continuation of Basu and Mansour.

Webb, A. T.↗
NASA NTRS1992

Piloted simulation study of a balloon-assisted deployment of an aircraft at high altitude

A piloted simulation was used to study the feasibility of a balloon assisted deployment of a research aircraft at high altitude. In the simulation study, an unmanned, modified sailplane was carried to 110,000 ft with a high altitude balloon and released in a nose down attitude. A remote pilot controlled the aircraft through a pullout and then executed a zoom climb to a trimmed, 1 g flight condition. A small parachute was used to limit the Mach number during the pullout to avoid adverse transonic effects. The use of small rocket motor was studied for increasing the maximum attainable altitude. Aerodynamic modifications to the basic sailplane included applying supercritical airfoil gloves over the existing wing and tail surfaces. The aerodynamic model of the simulated aircraft was based on low Reynolds number wind tunnel tests and computational techniques, and included large Mach number and Reynolds number effects at high altitude. Parametric variations were performed to study the effects of launch altitude, gross weight, Mach number limit, and parachute size on the maximum attainable stabilized altitude. A test altitude of approx. 95,000 ft was attained, and altitudes in excess of 100,000 ft was attained.

Murray, James↗
NASA NTRS1973

The effects of leading-edge serrations on reducing flow unsteadiness about airfoils, an experimental and analytical investigation

High frequency surface pressure measurements were obtained from wind-tunnel tests over the Reynolds number range 1.2 times one million to 6.2 times one million on a rectangular wing of NACA 63-009 airfoil section. Measurements were also obtained with a wide selection of leading-edge serrations added to the basic airfoil. Under a two-dimensional laminar bubble very close to the leading edge of the basic airfoil there is a large apatial peak in rms pressure. Frequency analysis of the pressure signals in this region show a large, high-frequency energy peak which is interpreted as an oscillation in size and position of the bubble. The serrations divide the bubble into segments and reduce the peak rms pressures. A low Reynolds number flow visualization test on a hydrofoil in water was also conducted. A von Karman vortex street was found trailing from the rear of the foil. Its frequency is at a much lower Strouhal number than in the high Reynolds number experiment, and is related to the trailing-edge and boundary-layer thicknesses.

Schwind, R. G.↗
NASA NTRS1935

Large-Scale Boundary-Layer Control Tests on Two Wings in the NACA 20-Foot Wind Tunnel, Special Report

Tests were made in the N.A.C.A. 20-foot wind tunnel on: (1) a wing, of 6.5-foot span, 5.5-foot chord, and 30 percent maximum thickness, fitted with large end plates and (2) a 16-foot span 2.67-foot chord wing of 15 percent maximum thickness to determine the increase in lift obtainable by removing the boundary layer and the power required for the blower. The results of the tests on the stub wing appeared more favorable than previous small-scale tests and indicated that: (1) the suction method was considerably superior to the pressure method, (2) single slots were more effective than multiple slots (where the same pressure was applied to all slots), the slot efficiency increased rapidly for increasing slot widths up to 2 percent of the wing chord and remained practically constant for all larger widths tested, (3) suction pressure and power requirements were quite low (a computation for a light airplane showed that a lift coefficient of 3.0 could be obtained with a suction as low as 2.3 times the dynamic pressure and a power expenditure less than 3 percent of the rated engine power), and (4) the volume of air required to be drawn off was quite high (approximately 0.5 cubic feet per second per unit wing area for an airplane landing at 40 miles per hour with a lift coefficient of 3,0), indicating that considerable duct area must be provided in order to prevent flow losses inside the wing and insure uniform distribution of suction along the span. The results from the tests of the large-span wing were less favorable than those on the stub wing. The reasons for this were, probably: (1) the uneven distribution of suction along the span, (2) the flow losses inside the wing, (3) the small radius of curvature of the leading edge of the wing section, and (4) the low Reynolds Number of these tests, which was about one half that of the stub wing. The results showed a large increase in the maximum lift coefficient with an increase in Reynolds Number in the range of the tests. The results of drag tests showed that the profile drag of the wing was reduced and the L/D ratio was increased throughout the range of lift coefficients corresponding to take-off and climb but that the minimum drag was increased. The slot arrangement that is best for low drag is not the same, however, as that for maximum lift.

Freeman, Hugh B.↗
NASA NTRS2019

Experimental Aerodynamic Simulation of Scallop Ice Accretion on a Swept Wing

Understanding the aerodynamic impact of swept-wing ice accretions is a crucial component of the design of modern aircraft. Computer-simulation tools are commonly used to approximate ice shapes, so the necessary level of detail or fidelity of those simulated ice shapes must be understood relative to high-fidelity representations of the ice. Previous tests were performed in the NASA Icing Research Tunnel to acquire high-fidelity ice shapes. From this database, full-span artificial ice shapes were designed and manufactured for both an 8.9%-scale and 13.3%-scale semispan wing model of the CRM65 which has been established as the full-scale baseline for this swept-wing project. These models were tested in the Walter H. Beech wind tunnel at Wichita State University and at the ONERA F1 facility, respectively. The data collected in the Wichita St. University wind tunnel provided a low-Reynolds number baseline study while the pressurized F1 facility produced data over a wide range of Reynolds and Mach numbers with the highest Reynolds number studied being approximately Re=11.9x106. Past work focused on only three different fidelity variations for ice shapes based on multiple icing conditions. This work presents a more detailed investigation into several fidelity representations of a single highly three-dimensional scallop ice accretion. Sensitivity to roughness size and application technique on a low-fidelity smooth ice shape is described. The data indicate that the aerodynamic performance is not especially sensitive to the grit variations. An ice accretion code was also used to generate ice shapes for aerodynamic testing and comparisons. These ice shapes have a general appearance like the low-fidelity smooth ice shapes, but in this case, the computer-generated ice shape is significantly smaller. As such, the impact of that ice shape on the aerodynamic performance of the wing is reduced compared to the smooth ice shape based on the icing experiment for those same conditions. Spanwise discontinuities were also introduced to a low-fidelity ice shape in an attempt to quantify the impact of those variation in the high-fidelity ice shape. While the lift data indicate good agreement between the high-fidelity ice shapes and the low-fidelity ice shapes and the low-fidelity ice shapes with spanwise discontinuities, a closer investigation of the data suggests potential, significant differences in the flowfield. These results were similar at both facilities over the wide range of test conditions utilized.

Woodard, Brian↗
NASA NTRS2023

Structural Design and Aeromechanical Analysis of Unconventional Blades for Future Mars Rotorcraft

The structural design for rotor blades with thin, unconventional airfoils for Earth-based testing is obtained using three-Dimensional (3D) aeromechanical analysis in support of the NASA ROAMX project. The outer mold line was provided by NASA, but the internal structural design was developed at the University of Maryland and is presented here along with a thorough aeromechanical analysis. The main objectives are to verify the structural integrity of the design and understand the unique aeroelastic behavior of the non-conventional airfoils designed for low-Reynolds number and high subsonic Mach number. Four different blade models are considered, with the pitch axis varied from quarter-chord to mid-chord to determine the effect of C.G. offset on natural frequencies, blade deformations, root loads, and 3D stresses. First, torsional stability is calculated for each of the designs – especially important due to the low Lock number on Mars. All four blade designs are studied under rotation in vacuum, and significant reductions in root loads and 3D stresses are achieved by moving the pitch axis closer to mid-chord to reduce the C.G. offset. Based on the vacuum analysis, the blade design with the pitch axis at 40% chord is selected for aeromechanical analysis. The blade control load, airloads, deformations, and 3D stresses are studied for steady hover. Dynamic control load and dynamic 3D stresses are studied for unsteady hover achieved using cyclic. Significant elastic twist is observed due to the trapeze effect and propeller moment, affecting the spanwise distribution of aerodynamic loads on the blades. The dynamic control load is found to increase significantly due to inertial coupling from the C.G. offset. The dynamic stresses also increase, although still have factors of safety greater than two for both tensile and compressive stress.

Structural Design↗
NASA NTRS2012

Boundary-Layer Instability Measurements in a Mach-6 Quiet Tunnel

Several experiments have been performed in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. A 7 degree half angle cone at 6 degree angle of attack with temperature-sensitive paint (TSP) and PCB pressure transducers was tested under quiet flow. The stationary crossflow vortices appear to break down to turbulence near the lee ray for sufficiently high Reynolds numbers. Attempts to use roughness elements to control the spacing of hot streaks on a flared cone in quiet flow did not succeed. Roughness was observed to damp the second-mode waves in areas influenced by the roughness, and wide roughness spacing allowed hot streaks to form between the roughness elements. A forward-facing cavity was used for proof-of-concept studies for a laser perturber. The lowest density at which the freestream laser perturbations could be detected was 1.07 x 10(exp -2) kilograms per cubic meter. Experiments were conducted to determine the transition characteristics of a streamwise corner flow at hypersonic velocities. Quiet flow resulted in a delayed onset of hot streak spreading. Under low Reynolds number flow hot streak spreading did not occur along the model. A new shock tube has been built at Purdue. The shock tube is designed to create weak shocks suitable for calibrating sensors, particularly PCB-132 sensors. PCB-132 measurements in another shock tube show the shock response and a linear calibration over a moderate pressure range.

Berridge, Dennis C.↗
NASA NTRS1983

Gas flow through rotameters

Using data available for small rotameters that use spherical floats in gas flow, a linear relationship is derived. It is noted that the relationship provides a good fit for variable volumetric flow, density, and viscosity at constant flow height. With low Reynolds numbers (Re being less than 1), the product of the variable volumetric flow and the viscosity becomes constant; at high Reynolds numbers (Re being greater than 2000), the product of the variable volumetric flow and the square root of the density becomes constant. It is pointed out that the equation given here can be used to obtain an indirect calibration with any gas of known density and viscosity. The constancy of the product of the variable volumetric flow and viscosity at low variable volumetric flows is seen as suggesting the development of simple, inexpensive gas viscometers using rotameter technology.

Levin, H.↗
NASA NTRSDate not supplied

Simulating Underexpanded Plumes in Martian and Lunar Environments

While the Loci/Chem Computational fluid dynamics (CFD) application has been validated and used extensively for simulating launch environments in atmospheric conditions, use of this tool for simulating supersonic plumes at much lower ambient pressure requires further validation. Simulations of underexpanded plumes have been performed using Loci/Chem at Martian pressure to predict several metrics for laminar, turbulent, and impinging plumes. The CFD results are compared with an experimental data set for low Reynolds number plumes at these conditions in order to evaluate the current capability of the Loci/Chem tool for these types of environments. The CFD validation results to date show reasonable agreement with the experimental data across all the metrics of interest for the configurations considered. The Loci/Chem-Boltzmann tool is a hybrid continuum/rarefied flow solver which extends modeling capabilities to very low-pressure environments such as those on the Moon. The Loci/Chem-Boltzmann solver uses a gradient-based continuum breakdown criterion to restrict solution of the computationally expensive Boltzmann equation to only a subset of the domain, while using the Navier-Stokes equations elsewhere. This CFD application is under active development, and current efforts toward establishing production ready capability for evaluating Lunar plume surface interactions are well under way. Initial simulations of an Apollo Lunar excursion module indicate that several regions of the flow require solving the Boltzmann equations due to extreme rarefaction. Early simulations are promising, indicating reasonable overall computational time for a full 3D human scale lander simulation.

Plume Surface Interaction↗
NASA NTRSDate not supplied

Simulating Underexpanded Jets in Martian and Lunar Environments

As part of the Game Changing Development (GCD) Program, funded by NASA’s Space Technology Mission Directorate (STMD), the development of simulation capability for the prediction of extra-terrestrial Plume Surface Interaction (PSI) environments has been undertaken by the Fluid Dynamics Branch at NASA/MSFC. The GCD PSI Project, planned to be accomplished over a four year period, contains a Predictive Simulation Capability (PSC) Element focused on creating simulation capability for the reliable and accurate prediction of PSI in Martian (~650 Pa) and Lunar (vacuum) ambient environments. In addition to the PSC Element, the PSI Project also contains a companion Ground Testing Element for development of focused datasets for validation of predictive capability as well as a Flight-focused Instrumentation Element. This paper describes the activities and accomplishments in the past year for the Prediction of Plume Flow in low pressure environments component of the PSI Project. While the Loci/Chem Computational fluid dynamics (CFD) application has been validated and used extensively for simulating launch environments in atmospheric conditions, use of this tool for simulating supersonic plumes at Mars-like ambient pressure requires further validation. CFD simulations of underexpanded jets have been performed using Loci/Chem for Mars-like conditions to predict several metrics for steady laminar, turbulent, and impinging plumes. The CFD results are compared with an experimental data set for low Reynolds number plumes at these conditions in order to evaluate the current capability of the Loci/Chem tool for these types of environments. The CFD validation results to date show reasonable agreement with the experimental data across all of the metrics of interest for the configurations considered. The Loci/Chem-Boltzmann CFD application is a hybrid continuum/rarefied flow solver which extends modeling capabilities to very low pressure environments such as those on the Moon. The Loci/Chem-Boltzmann solver uses a gradient-based continuum breakdown criterion to restrict solution of the computationally expensive Boltzmann equation to only a subset of the domain, while using the Navier-Stokes equations elsewhere. This CFD application is under active development, and current efforts toward establishing production ready capability for evaluating Lunar plume surface interactions are well under way. Initial simulations of an Apollo LEM indicate that several regions of the flow require solving the Boltzmann equations due to extreme rarefaction. Early simulations are promising, indicating reasonable overall computational time for a full 3D human scale lander simulation.

Thomas Shurtz↗
NASA NTRS2003

Computational Methods for Jet Noise Simulation

The purpose of our project is to develop, analyze, and test novel numerical technologies central to the long term goal of direct simulations of subsonic jet noise. Our current focus is on two issues: accurate, near-field domain truncations and high-order, single-step discretizations of the governing equations. The Direct Numerical Simulation (DNS) of jet noise poses a number of extreme challenges to computational technique. In particular, the problem involves multiple temporal and spatial scales as well as flow instabilities and is posed on an unbounded spatial domain. Moreover, the basic phenomenon of interest, the radiation of acoustic waves to the far field, involves only a minuscule fraction of the total energy. The best current simulations of jet noise are at low Reynolds number. It is likely that an increase of one to two orders of magnitude will be necessary to reach a regime where the separation between the energy-containing and dissipation scales is sufficient to make the radiated noise essentially independent of the Reynolds number. Such an increase in resolution cannot be obtained in the near future solely through increases in computing power. Therefore, new numerical methodologies of maximal efficiency and accuracy are required.

Goodrich, John W.↗
NASA NTRS1973

Wall boundary equations with slip and catalysis for multicomponent, nonequilibrium gas flows

Boundary equations obtained for a low Reynolds number, high enthalpy gas flow in regions of velocity slip and temperature jump are presented. The formulation treats, through a first-order distribution function used to include multicomponent diffusion, a multicomponent gas mixture that may be in nonequilibrium with finite-rate catalytic recombination occurring on the wall. In the boundary equations, which are obtained for use in flow-field calculations applicable to low-density flow regimes, a simplified gas/wall interaction is assumed wherein individual atoms or molecules either reflect specularly off the wall or stick and are fully accommodated. Fluxes in terms of evaluated integrals over the distribution function and integrals necessary for determining fluxes are given.

Scott, C. D.↗
NASA NTRS1962

STABILITY OF FILM BOILING TWO-PHASE FLOW IN CRYOGENIC SYSTEMS

The stability of film boiling two phase flow is investigated referring in particular to saturated cryogenic liquids. This type of fluid motion is unstable, such that a range of wave numbers will always be present in which disturbances are amplified. Further the mode of operation of the energy supply system may favour temperature fluctuations of large amplitude if the circuit does not provide feed-back compensation. The theoretically predicted stabilization due to capillarity is reduced considerably in liquefied gases with low surface tension, such as hydrogen. This effect causes the transition to turbulent flow to occur at low Reynolds numbers, and increases the heat transport in the turbulent regime. A comparison with experimental data, (horizontal cylinder), shows that the "critical" film Reynolds number ūδ/𝜈, at which instabilities become effective, is lowered from approximately 200, (O2), to about 30, (H2). Similar results have been found with other configurations. Therefore application of laminar film boiling solutions is restricted to small objects, entrance regions, or stagnation points. Turbulent correlations given so far are valid only for a certain group of substances with similar behavior.

LIQUID FLOW↗
NASA NTRS1987

Computation and analysis of a cylinder wake flow

The Karman vortex wake of a circular cylinder at low Reynolds number was computed by a time-accurate, two-dimensional compressible Navier-Stokes equation solver which uses the MacCormack predictor-corrector finite-difference scheme and a nonreflecting boundary condition on the outer flow boundary. The results from a large number of time steps were analyzed using Fast Fourier Transform techniques to identify the important frequency components for comparison with published experimental data. A strong low-frequency component was found below the vortex shedding frequency and not harmonically related to it. The experimentally discovered low-frequency fluctuations in the cylinder wake are considered possibly to be precursors to transition from laminar to turbulent flow conditions. The present finding of similar frequencies in a computed wake tends to confirm their existence as a real wake phenomenon. This computational work provides a complementary means to experimental investigations of wake phenomena.

Townsend, J. C.↗