Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Lithium Battery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A Cobalt– and Manganese–Free High–Nickel Layered Oxide Cathode for Long–Life, Safer Lithium–Ion Batteries

High-nickel LiNi 1–x–y Mn x Co y O 2 and LiNi 1–x–y Co x Al y O 2 cathodes are receiving growing attention due to the burgeoning demands on high-energy-density lithium-ion batteries. The presence of both cobalt and manganese in them, however, triggers multiple issues, including high cost, high toxicity, rapid surface deterioration, and severe transition-metal dissolution. Herein, a Co- and Mn-free ultrahigh-nickel LiNi 0.93 Al 0.05 Ti 0.01 Mg 0.01 O 2 (NATM) cathode that exhibits 82% capacity retention over 800 deep cycles in full cells, outperforming two representative high-Ni cathodes LiNi 0.94 Co 0.06 O 2 (NC, 52%) and LiNi 0.90 Mn 0.05 Co 0.05 O 2 (NMC, 60%) is presented. It is demonstrated that a titanium-enriched surface along with aluminum and magnesium as the stabilizing ions in NATM not only ameliorates unwanted side reactions with the electrolyte and structural disintegrity, but also mitigates transition-metal dissolution and active lithium loss on the graphite anode. As a result, the graphite anode paired with NATM displays an ultrathin (≈8 nm), monolayer anode-electrolyte interphase architecture after extensive cycling. Furthermore, NATM displays considerably enhanced thermal stability with an elevated exothermic temperature (213 °C for NATM vs 180 and 190 °C for NC and NMC, respectively) and remarkably reduced heat release. This work sheds light on rational compositional design to adopt ultrahigh-Ni cathodes in lithium-based batteries with low cost, long service life, and improved thermal stability.

25 ENERGY STORAGE↗
DOE OSTI2023

Effects of cathode loadings and anode protection on the performance of lithium metal batteries

Abstract While lithium-ion batteries (LIBs) are approaching their energy limits, lithium metal batteries (LMBs) are undergoing intensive investigation for higher energy density. Coupling LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathode with lithium (Li) metal anode, the resultant Li||NMC811 LMBs are among the most promising technologies for future transportation electrification, which have the potential to realize an energy density two times higher than that of state-of-the-art LIBs. To maximize their energy density, the Li||NMC811 LMBs are preferred to have their cathode loading as high as possible while their Li anode as thin as possible. To this end, we investigated the effects of different cathode active material loadings (2–14 mg cm −2 ) on the performance of the Li||NMC811 LMBs. Our study revealed that the cathode loadings have remarkably affected the cell performance, in terms of capacity retention and sustainable capacity. Cells with high cathode loadings are more liable to fade in capacity, due to more severe formation of the CEI and more sluggish ion transport. In this study, we also verified that the protection of the Li anode is significant for achieving better cell performance. In this regard, our newly developed Li-containing glycerol (LiGL) via molecular layer deposition (MLD) is promising to help boost the cell performance, which was controllably deposited on the Li anode.

Materials Science↗
DOE OSTI2020

Self-supported MoO 2 /MoS 2 nano-sheets embedded in a carbon cloth as a binder-free substrate for high-energy lithium–sulfur batteries

As one of the most prospective candidates for next-generation rechargeable batteries, lithium-sulfur (Li-S) batteries currently still encounter great challenges associated with the low conductivity, severe shuttle effects, and sluggish redox kinetics. Herein, a self-supported sulfur host is fabricated by an in-situ growth of MoO 2 /MoS 2 nano-sheets on a carbon cloth (CC). First, carbon cloth serves as a good template for the morphology-controlled synthesis of nanostructured materials, which not only alleviates the agglomeration of MoO2/MoS2, but also enhances the flexibility and mechanical strengthen of the hybrid architecture as a free-standing host. Second, the polysulfide-trapping ability can be greatly enhanced by both physical and chemical adsorption from the MoO 2 /MoS 2 -anchored carbon cloth. Moreover, the partially sulfurized MoO 2 /MoS 2 nano-sheets integrate the benefits of conductive MoO 2 and sulfiphilic MoS 2 , thus facilitating fast charge transfer and redox kinetics of polysulfide conversion. As a result, these attributes enable the host to hold a high sulfur loading (up to 7.6 mg cm -2 ), which exceeds most of the reported carbon cloth-related cathode work in the literature. Furthermore, the Li-S cells can achieve a high peak capacity of 1350 mA h g -1 , excellent rate capability (C/20 - 2C rate), impressive areal capacity (up to 6.3 mA h cm -2 ), and a high capacity retention of 85% after 100 cycles.

25 ENERGY STORAGE↗
DOE OSTI2023

Understanding of Low‐Porosity Sulfur Electrode for High‐Energy Lithium–Sulfur Batteries

Abstract The lithium–sulfur (Li–S) battery is a promising technology for large‐scale energy storage and vehicle electrification due to its high theoretical energy density and low cost. Reducing the sulfur cathode porosity has been identified recently as a viable strategy for improving the cell practical energy density and minimizing pore‐filling electrolytes to extend cell life at lean electrolyte conditions. Direct use of a low‐porosity cathode for Li–S battery results in poor electrode wetting, nonuniform electrode reactions, and thus early cell failure. To understand and mitigate the barriers associated with the use of low‐porosity electrodes, multiscale modeling is performed to predict electrode wetting, electrolyte diffusion, and their impacts on sulfur reactions in Li–S cells by explicitly considering the electrode wettability impacts and electrode morphologies. The study elucidates the critical impact of low tortuosity and large channel pore design for promoting electrode wetting and species diffusion. It is suggested that the secondary particle size should be comparable with the electrode thickness to effectively promote electrolyte wettability and sulfur reactivity. This study provides new insights into the low‐porosity electrode material and designs and is expected to accelerate the development of practical high‐energy Li–S batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

High–Nickel NMA: A Cobalt–Free Alternative to NMC and NCA Cathodes for Lithium–Ion Batteries

High-nickel LiNi 1–x–y Mn x Co y O 2 (NMC) and LiNi 1–x–y Co x Al y O 2 (NCA) are the cathode materials of choice for next-generation high-energy lithium-ion batteries. Both NMC and NCA contain cobalt, an expensive and scarce metal generally believed to be essential for their electrochemical performance. Herein, a high-Ni LiNi 1–x–y Mn x Al y O 2 (NMA) cathode of desirable electrochemical properties is demonstrated benchmarked against NMC, NCA, and Al–Mg-codoped NMC (NMCAM) of identical Ni content (89 mol%) synthesized in-house. Despite a slightly lower specific capacity, high-Ni NMA operates at a higher voltage by ≈40 mV and shows no compromise in rate capability relative to NMC and NCA. In pouch cells paired with graphite, high-Ni NMA outperforms both NMC and NCA and only slightly trails NMCAM and a commercial cathode after 1000 deep cycles. Further, the superior thermal stability of NMA to NMC, NCA, and NMCAM is shown using differential scanning calorimetry. Here, considering the flexibility in compositional tuning and immediate synthesis scalability of high-Ni NMA very similar to NCA and NMC, this study opens a new space for cathode material development for next-generation high-energy, cobalt-free Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Understanding the Chemomechanical Function of the Silver–Carbon Interlayer in Sheet-type All-Solid-State Lithium–Metal Batteries

All-solid-state batteries with lithium metal anodes hold great potential for high-energy battery applications. However, forming and maintaining stable solid–solid contact between the lithium anode and solid electrolyte remains a major challenge. One promising solution is the use of a silver–carbon (Ag–C) interlayer, but its chemomechanical properties and impact on interface stabilities need to be comprehensively explored. Here, we examine the function of Ag–C interlayers in addressing interfacial challenges using various cell configurations. Experiments show that the interlayer improves interfacial mechanical contact, leading to a uniform current distribution and suppressing lithium dendrite growth. Furthermore, the interlayer regulates lithium deposition in the presence of Ag particles via improved Li diffusivity. The sheet-type cells with the interlayer achieve a high energy density of 514.3 Wh L –1 and an average Coulombic efficiency of 99.97% over 500 cycles. Furthermore, this work provides insights into the benefits of using Ag–C interlayers for enhancing the performance of all-solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Advanced electrolytes for fast-charging high-voltage lithium-ion batteries in wide-temperature range

LiNixMnyCo1-x-yO2 (NMC) cathode materials with Ni=0.8 have attracted great interest for application in high energy-density lithium (Li)-ion batteries (LIBs) because of their high specific capacities at high voltages. However, the practical application of Ni-rich NMC in LIBs under high charge voltages (e.g. 4.4 V and above) still faces big challenges due to the severe capacity fading, which is directly related to the instability of the cathode/electrolyte interface. In this work, we develop new localized high-concentration electrolytes (LHCEs) based on carbonate solvents, which are compatible with graphite (Gr) anode and have a high oxidation potential over 4.9 V vs. Li/Li+. The optimal LHCE enables the Gr||NMC811 cells with 2.8 mAh cm-2 cathode areal capacity loading to achieve an excellent cycling stability over 600 cycles with a capacity retention of 94.2 % under a charge cut-off voltage of 4.4 V at 25 ?C, good rate capabilities under fast charging or discharging up to 3C rate, and superior low-temperature discharge performance down to -30 ?C with a capacity retention of 85.6% at C/5 rate. The findings in this work shed light a very promising strategy to develop new electrolytes for practical high-energy LIBs with Ni-rich NMC cathodes.

Zhang, Xianhui↗
DOE OSTI2020

A lithium-sulfur battery with a solution-mediated pathway operating under lean electrolyte conditions

Lithium-sulfur (Li-S) battery is one of the most promising candidates for the next generation energy storage systems. However, several barriers, including polysulfide shuttle effect, the slow solid-solid surface reaction pathway in the lower discharge plateau, and corrosion of Li anode still limit its practical applications, especially under the lean electrolyte condition required for high energy density applications. Here, we propose a solution-mediated sulfur reduction pathway to improve the capacity and reversibility of the sulfur cathode and suppress dendrite growth on the Li metal anode simultaneously. With this method, a high coulombic efficiency (99%) and stable cycle life over 100 cycles were achieved under application-relevant conditions (S loading: 6.2 mg cm-2; electrolyte to sulfur ratio: 3 mLE gs-1; sulfur weigh ratio: 72 wt%). This result is enabled by a specially designed Li2S4-rich electrolyte, in which Li2S is formed through a chemical disproportionation reaction instead of electrochemical routes. A diglyme solvent was used to obtain electrolytes with the optimum range of Li2S4 concentration. Operando X-ray absorption spectroscopy confirms the solution pathway in a practical Li-S cell. This solution pathway not only introduces a new electrolyte regime for practical Li-S batteries, but also provides a new perspective for bypassing the inefficient surface pathway for other electrochemical processes.

Wang, Hui↗
DOE OSTI2023

Precise Tailoring of Lithium-Ion Transport for Ultralong-Cycling Dendrite-Free All-Solid-State Lithium Metal Batteries

All-solid-state lithium metal batteries can address crucial challenges regarding insufficient battery cycling life and energy density. The demonstration of long-cycling dendrite-free all-solid-state lithium metal batteries requires precise tailoring of lithium-ion transport of solid-state electrolytes (SSEs). Here, in this work, a proof of concept is reported for precise tailoring of lithium-ion transport of a halide SSE, Li 3 InCl 6 , including intragranular (within grains) but also intergranular (between grains) lithium-ion transport. Lithium-ion migration tailoring mechanism in crystals is developed by unexpected enhanced Li, In, and Cl vacancy populations and lower energy barrier for hopping. The lithium-ion transport tailoring mechanism between the grains is determined by the elimination of voids between grains and the formation of unexpected supersonic conducting grain boundaries, boosting the lithium dendrite suppression ability of SSE. Due to boosted lithium-ion conduction and dendrite-suppression ability, the all-solid-state lithium metal batteries coupled with Ni-rich LiNi 0.83 Co 0.12 Mn 0.05 O 2 cathodes and lithium metal anodes demonstrate breakthroughs in electrochemical performance by achieving extremely long cycling life at a high current density of 0.5 C (2000 cycles, 93.7% capacity retention). This concept of precise tailoring of lithium-ion transport provides a cost, time, and energy efficient solution to conquer the remaining challenges in all-solid-state lithium-metal batteries for fast developing electric vehicle markets.

25 ENERGY STORAGE↗
DOE OSTI2024

Extracting and Interpreting Electrochemical Impedance Spectra (EIS) from Physics-Based Models of Lithium-Ion Batteries

This paper implements a highly efficient algorithm to extract electrochemical impedance spectra (EIS) from physics-based battery models (e.g., a P2D model). The mathematical approach is different from how EIS is practiced experimentally. Experimentally, the voltage (current) is harmonically perturbed over a wide range of frequencies and the amplitude and phase shift of the corresponding current (voltage) is measured. The experimental approach can be implemented in simulation software, but is computationally expensive. The approach here is to determine locally linear state-space models from the full physical model. The four Jacobian matrices that are the basis of the state-space models can be derived by numerical differentiation of the physical model. The EIS is then extracted from the state-space model using computationally efficient matrix-manipulation techniques. The algorithm can evaluate the full EIS at an instant in time during a transient, independent of whether the battery is in a stationary state. The approach is also able to separate the full-cell impedance to evaluate partial EIS, such as for a battery anode alone. Although such partial EIS is difficult to measure experimentally, the partial EIS provides valuable insights in interpreting the full-cell EIS.

25 ENERGY STORAGE↗
DOE OSTI2024

Cost Analysis and Projections for U.S.-Manufactured Automotive Lithium-ion Batteries

This document reports on a study conducted to estimate the cost of U.S-produced automotive battery packs for model years (MY) 2023 to 2035, using Argonne National Laboratory’s BatPaC tool. The costs were estimated by designing batteries for several classes of vehicles for four discrete model years (2023, 2026, 2030, and 2035), where a representative battery technology and material prices are selected based on information available today. Correlations were developed from the four discrete years to enable annual pack cost estimates as a function of pack size (kWh) and model year. A consolidated cost curve was then developed that includes battery size, technology by model year, and the anticipated sales volumes of each class of vehicles over the years. This cost curve estimates the volume-averaged, U.S.-manufactured battery pack cost of PHEVs and BEVs in the United States to be $\$140$/kWh for the model year 2023, which will reduce to $\$86$/kWh in MY2035. Applying tax credits from section 45X of the Inflation Reduction Act can further reduce the average pack cost to as low as $\$56$/kWh in MY2029. The report also includes several sensitivity studies that investigate the effect of pack production volume, material prices, fast charge requirements, and labor rates.

25 ENERGY STORAGE↗
DOE OSTI2022

High-Safety Electrolytes for Lithium-Ion Batteries : Is non-flammability of electrolyte overrated in the overall safety performance of lithium ion batteries?

It has been widely considered that the flammability of the liquid electrolyte is one of the most influential factors that determine the safety of lithium ion batteries (LIBs). Following this consideration, a completely non-flammable electrolyte was designed and adopted to graphite||LiFePO 4 (Gr||LFP) batteries. Contrary to the conventional understanding, the completely non-flammable electrolyte with phosphorus-containing solvents exhibits inferior safety performance in commercial Gr||LFP batteries, in comparison to the flammable conventional LiPF 6 -organocarbonate electrolyte. Mechanistic studies identify the exothermic reactions between the electrolyte (especially the flame retarding phosphate solvent) and the charged electrodes as the “culprit” behind such a counterintuitive phenomenon. The discovery emphasizes the importance of reducing the electrolyte reactivity when designing safe electrolytes, as well as the necessity of evaluating safety performances of electrolyte on a battery level.

25 ENERGY STORAGE↗
DOE OSTI2020

Low-temperature and high-rate-charging lithium metal batteries enabled by an electrochemically active monolayer-regulated interface

Stable operation of rechargeable lithium (Li)-based batteries at low temperatures is vital for cold-climate applications but is plagued with dendritic Li plating and unstable solid-electrolyte interphase (SEI). Here we report high-performance Li-metal batteries under low-temperature and high-rate-charging conditions. This is realized by utilizing a self-assembled monolayer of electrochemically active molecules on current collectors that regulates the nanostructure and composition of SEI and deposition morphology of Li metal anodes. A multilayer SEI containing a LiF-rich inner phase and amorphous outer layer effectively seals the Li surface in contrast to the conventional impassive SEI at low temperatures. As a result, galvanic Li corrosion and self-discharge were suppressed; stable Li deposition was realized from -60º to 45ºC; and a Li|LiCoO 2 cell with a capacity of 2.0 mAh cm -2 displayed a 200-cycle life at -15ºC with a recharge time of 45 minutes.

25 ENERGY STORAGE↗
NASA NTRS2001

Chemical State of Surface Oxygen on Carbon and Its Effects on the Capacity of the Carbon Anode in a Lithium-Ion Battery Investigated

In a lithium-ion battery, the lithium-storage capacity of the carbon anode is greatly affected by a surface layer formed during the first half cycle of lithium insertion and release into and out of the carbon anode. The formation of this solid-electrolyte interface, in turn, is affected by the chemistry of the carbon surface. A study at the NASA Glenn Research Center examined the cause-and-effect relations. Information obtained from this research could contribute in designing a high-capacity lithium-ion battery and, therefore, small, powerful spacecraft. In one test, three types of surfaces were examined: (1) a surface with low oxygen content (1.5 at.%) and a high concentration of active sites, (2) a surface with 4.5 at.% -OH or -OC type oxygen, and (3) a surface with 6.5 at.% O=C type oxygen. The samples were made from the same precursor and had similar bulk properties. They were tested under a constant current of 10 mA/g in half cells that used lithium metal as the counter electrode and 0.5 M lithium iodide in 50/50 (vol%) ethylene carbonate and dimethyl carbonate as the electrolyte. For the first cycle of the electrochemical test, the graph describes the voltage of the carbon anode versus the lithium metal as a function of the capacity (amount of lithium insertion or release). From these data, it can be observed that the surface with low oxygen and a high concentration of active sites could result in a high irreversible capacity. Such a high irreversible capacity could be prevented if the active sites were allowed to react with oxygen in air, producing -OH or -OC type oxygen. The O=C type oxygen, on the other hand, could greatly reduce the capacity of lithium intercalation and, therefore, needs to be avoided during battery fabrication.

Hung, Ching-Cheh↗