SEARCH · Engineering Papers

Results for “JuMP model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Steady-state dynamic behavior of an auxiliary bearing supported rotor system

This paper investigates the steady-state responses of a rotor system supported by auxiliary bearings in which there is a clearance between the rotor and the inner race of the bearing. A simulation model based upon the rotor of a production jet engine is developed and its steady-state behavior is explored over a wide range of operating conditions for various parametric configurations. Specifically, the influence of rotor imbalance, support stiffness, and damping is studied. It is found that imbalance may change the rotor responses dramatically in terms of frequency contents at certain operating speeds. Subharmonic responses of 2nd order through 10th order are all observed except the 9th order. Chaotic phenomenon is also observed. Jump phenomena (or double-valued responses) of both hard-spring type and soft-spring type are shown to occur at low operating speeds for systems with low auxiliary bearing damping or large clearance even with relatively small imbalance. The effect of friction between the shaft and the inner race of the bearing is also discussed.

Xie, Huajun↗

NASA NTRS1979

Effective temperatures, angular diameters, distances and linear radii for 160 O and B stars

This paper discusses effective temperatures, angular diameters, distances, and linear diameters that have been determined for 160 O and B stars on the basis of published UV spectrophotometry, visible and near-IR intermediate-band photometry, and model-atmosphere fluxes. The results are compared with previous measurements and calculations for main-sequence and giant O and B stars. It is found that: (1) the flux effective temperatures of O and B supergiants are systematically lower than those of main-sequence and giant stars of the same subtype; (2) the effective temperatures and radii of Beta Cep stars are the same as those of nonvariable stars of the same spectral type; (3) Be stars that do not have two Balmer jumps have effective temperatures very similar to those of normal B stars of the same subtype; (4) O and B stars increase in size from the main sequence to supergiants; and (5) late B supergiants are approximately twice as large as O9 supergiants.

Underhill, A. B.↗

NASA NTRS1983

The effect of a coronal shock wave on the solar wind ionization state

In connection with studies of solar wind ionization state freezing, it is shown that, by using a Lagrangian approach of following individual fluid parcels, the techniques used previously for calculating ionization state variations in a steady state case can be extended straightforwardly to time-varying flows. The specific ionization state calculations presented are for a relatively simple picture of time-dependent coronal flow, based on a well-known model of a self-similar shock wave propagating through the corona. Time-dependent ionization effects for the sudden transition between two otherwise steady flows are likely to be limited to a narrow range of gas parcels which, having been shocked within the coronal freezing-in radius, pass a fixed interplanetary observer in an interval of a few tens of minutes. The amplitude of any rise in interplanetary ionization temperature associated with the coronal shock is likely to be considerably smaller than the jump in electron temperature that actually occurs in the corona.

Owocki, S. P.↗

NASA NTRS1992

Cellular instability in rapid directional solidification - Bifurcation theory

Merchant and Davis performed a linear stability analysis on a model for the directional solidification of a dilute binary alloy valid for all speeds. The analysis revealed that nonequilibrium segregation effects modify the Mullins and Sekerka cellular mode, whereas attachment kinetics has no effect on these cells. In this paper, the nonlinear stability of the steady cellular mode is analyzed. A Landau equation is obtained that determines the amplitude of the cells. The Landau coefficient here depends on both nonequilibrium segregation effects and attachment kinetics. This equation gives the ranges of parameters for subcritical bifurcation (jump transition) or supercritical bifurcation (smooth transition) to cells.

Braun, R. J.↗

NASA NTRS2009

Physiological Factors Contributing to Postflight Changes in Functional Performance

Astronauts experience alterations in multiple physiological systems due to exposure to the microgravity conditions of space flight. These physiological changes include sensorimotor disturbances, cardiovascular deconditioning and loss of muscle mass and strength. These changes might affect the ability of crewmembers to perform critical mission tasks immediately after landing on lunar and Martian surfaces. To date, changes in functional performance have not been systematically studied or correlated with physiological changes. To understand how changes in physiological function impact functional performance an interdisciplinary pre/postflight testing regimen (Functional Task Test, FTT) has been developed that systematically evaluates both astronaut postflight functional performance and related physiological changes. The overall objectives of the FTT are to: Develop a set of functional tasks that represent critical mission tasks for Constellation. Determine the ability to perform these tasks after flight. Identify the key physiological factors that contribute to functional decrements. Use this information to develop targeted countermeasures. The functional test battery was designed to address high priority tasks identified by the Constellation program as critical for mission success. The set of functional tests making up the FTT include the: 1) Seat Egress and Walk Test, 2) Ladder Climb Test, 3) Recovery from Fall/Stand Test, 4) Rock Translation Test, 5) Jump Down Test, 6) Torque Generation Test, and 7) Construction Activity Board Test. Corresponding physiological measures include assessments of postural and gait control, dynamic visual acuity, fine motor control, plasma volume, orthostatic intolerance, upper and lower body muscle strength, power, fatigue, control and neuromuscular drive. Crewmembers will perform both functional and physiological tests before and after short (Shuttle) and long-duration (ISS) space flight. Data will be collected on R+0 (Shuttle only), R+1, R+6 and R+30. Using a multivariate regression model we will identify which physiological systems contribute the most to impaired performance on each functional test. This will allow us to identify the physiological systems that play the largest role in decrement in functional performance. Using this information we can then design and implement countermeasures that specifically target the physiological systems most responsible for the altered functional performance associated with space flight.

Bloomberg, J. J.↗

NASA NTRS2011

Interchange Slip-Running Reconnection and Sweeping SEP-Beams

We present a new model to explain how particles, accelerated at a reconnection site that is not magnetically connected to the Earth, could eventually propagate along the well-connected open flux tube. Our model is based on the results of a low-beta resistive magnetohydrodynamics simulation of a three-dimensional line-tied and initially current-free bipole, that is embedded in a non-uniform open potential field. The topology of this configuration is that of an asymmetric coronal null-point, with a closed fan surface and an open outer spine. When driven by slow photospheric shearing motions, field lines, initially fully anchored below the fan dome, reconnect at the null point, and jump to the open magnetic domain. This is the standard interchange mode as sketched and calculated in 2D. The key result in 3D is that, reconnected open field lines located in the vicinity of the outer spine, keep reconnecting continuously, across an open quasi-separatrix layer, as previously identified for non-open-null-point reconnection. The apparent slipping motion of these field lines leads to form an extended narrow magnetic flux tube at high altitude. Because of the slip-running reconnection, we conjecture that if energetic particles would be travelling through, or be accelerated inside, the diffusion region, they would be successively injected along continuously reconnecting field lines that are connected farther and farther from the spine. At the scale of the full Sun, owing to the super-radial expansion of field lines below 3 solar radius, such energetic particles could easily be injected in field lines slipping over significant distances, and could eventually reach the distant flux tube that is well-connected to the Earth.

Masson, S.↗

NASA NTRS2022

Simulating the Diffusion of Hydrogen in Amorphous Silicates: A ‘Jumping’ Migration Process and its Implications for Solar Wind Implanted Lunar Volatiles

We use molecular dynamics (MD) simulations to better explain the movement of atomic hydrogen in amorphous silica and quantify the planetary science implications of these findings. Previous MD simulations had a large range of predicted values and did not agree well with experiment. Our simulations sample atomic motion for a longer duration and consider a wider range of temperatures than previous simulations. In contrast to constant atomic motion, the hydrogen atoms were shown to undergo random intermittent jumps from one oxygen atom to another, the number of which increase with temperature. Predicted diffusion coefficients had a better agreement to experimental values than previous MD simulations, suggesting the importance of longer simulation durations for better statistics. The low activation energy and jumps observed at lunar temperatures do not support the theory of diurnal variations in OH content for an undamaged amorphous silica surface. Instead, we conclude that energetic solar wind impacts can induce two competing atomic hydrogen motion processes in the exposed surface: A prompt effect that induces jumps in the temperature spike volume, but also a long term effect of damage in the structure that traps atomic hydrogen. We then use SDTrimSP to quantify the damage created during exposure and MD to demonstrate the H retention and trapping near these defects. Damage was shown to be dependent on impact energy, with defects easily retaining implanted hydrogen. MD results like those presented herein on unweathered surfaces are therefore most relevant to magnetic anomalies. As a result, we demonstrate the importance of lunar volatile models to account for the damage state of the substrate when modelling hydrogen diffusion, retention, and subsequent OH/water production.

Liam S. Morrissey↗

DOE OSTI2020

BASS: An R Package for Fitting and Performing Sensitivity Analysis of Bayesian Adaptive Spline Surfaces

In this work, we present the R package BASS as a tool for nonparametric regression. The primary focus of the package is fitting fully Bayesian adaptive spline surface (BASS) models and performing global sensitivity analyses of these models. The BASS framework is similar to that of Bayesian multivariate adaptive regression splines (BMARS) from Denison, Mallick, and Smith (1998), but with many added features. The software is built to efficiently handle significant amounts of data with many continuous or categorical predictors and with functional response. Under our Bayesian framework, most priors are automatic but these can be modified by the user to focus on parsimony and the avoidance of overfitting. If directed to do so, the software uses parallel tempering to improve the reversible jump Markov chain Monte Carlo (RJMCMC) methods used to perform inference. We discuss the implementation of these features and present the performance of BASS in a number of analyses of simulated and real data.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS2007

Large-Area Permanent-Magnet ECR Plasma Source

A 40-cm-diameter plasma device has been developed as a source of ions for material-processing and ion-thruster applications. Like the device described in the immediately preceding article, this device utilizes electron cyclotron resonance (ECR) excited by microwave power in a magnetic field to generate a plasma in an electrodeless (noncontact) manner and without need for an electrically insulating, microwave-transmissive window at the source. Hence, this device offers the same advantages of electrodeless, windowless design - low contamination and long operational life. The device generates a uniform, high-density plasma capable of sustaining uniform ion-current densities at its exit plane while operating at low pressure [<10(exp -4) torr (less than about 1.3 10(exp -2) Pa)] and input power <200 W at a frequency of 2.45 GHz. Though the prototype model operates at 2.45 GHz, operation at higher frequencies can be achieved by straightforward modification to the input microwave waveguide. Higher frequency operation may be desirable in those applications that require even higher background plasma densities. In the design of this ECR plasma source, there are no cumbersome, power-hungry electromagnets. The magnetic field in this device is generated by a permanent-magnet circuit that is optimized to generate resonance surfaces. The microwave power is injected on the centerline of the device. The resulting discharge plasma jumps into a "high mode" when the input power rises above 150 W. This mode is associated with elevated plasma density and high uniformity. The large area and uniformity of the plasma and the low operating pressure are well suited for such material-processing applications as etching and deposition on large silicon wafers. The high exit-plane ion-current density makes it possible to attain a high rate of etching or deposition. The plasma potential is <3 V low enough that there is little likelihood of sputtering, which, in plasma processing, is undesired because it is associated with erosion and contamination. The electron temperature is low and does not vary appreciably with power.

Foster, John E.↗

NASA NTRS1991

A determination of relativistic shock jump conditions using Monte Carlo techniques

Monte Carlo techniques are used, assuming isotropic elastic scattering of all particles, to calculate jump conditions in parallel relativistic collisionless shocks in the absence of Fermi acceleration. The shock velocity and compression ratios are shown for arbitrary flow velocities and for any upstream temperature. Both single-component electron-positron plasma and two-component proton-electron plasmas are considered. It is shown that protons and electrons must share energy, directly or through the mediation of plasma waves, in order to satisfy the basic conservation conditions, and the electron and proton temperatures are determined for a particular microscopic, kinetic-theory model, namely, that protons always scatter elastically. The results are directly applicable to shocks in which waves of scattering superthermal particles are absent.

Ellison, Donald C.↗

NASA NTRS1994

Towards a Modern Theory of Multiphase Filtration Flow

An alternative theoretical model of joint filtration flow of immiscible incompressible fluids is presented. The model takes into account relaxation processes due to the interchange of the fluids between pores of difference sizes which is driven by capillary forces. The fluids occupy connected regions in a four-dimensional space formed by three coordinates and the pore length scale. When the fluid exchange between pores of given sizes is effected by way of successive flow through pores of all the intermediate sizes, the pressure within each region is governed by a hyperbolic equation, the role of time being played by the pore linear scale. Pressure jumps across hypersurfaces separating the regions equal corresponding values of the capillary pressure. A supplementary condition at any such hypersurface requires the speed of its displacement in the four-dimensional space to coincide with the normal velocity components of both the adjoining fluids. As a result, a principally new statement of multiphase filtration flow problems is gained with allowance for capillary relaxation in the porous space.

Buyevich, Yu A.↗

DOE OSTI2021

Dynamical piezomagnetic effect in time-reversal-invariant Weyl semimetals with axionic charge density waves

Charge density waves (CDWs) in Weyl semimetals (WSMs) have been shown to induce an exotic axionic insulating phase in which the sliding mode (phason) of the CDW acts as a dynamical axion field, giving rise to a large positive magnetoconductance. In this work, we predict that dynamical strain can induce a bulk orbital magnetization in time-reversal (TR)-invariant WSMs that are gapped by a CDW. Here, we term this effect the “dynamical piezomagnetic effect” (DPME). Unlike in J. Gooth et al., the DPME introduced in this work occurs in a bulk-constant (i.e., static and spatially homogeneous in the bulk) CDW, and does not rely on fluctuations, such as a phason. By studying the low-energy effective theory and a minimal tight-binding (TB) model, we find that the DPME originates from an effective valley axion field that couples the electromagnetic gauge field with a strain-induced pseudogauge field. In particular, whereas the piezoelectric effects studied in previous works are characterized by 2D Berry curvature, the DPME represents the first example of a fundamentally 3D strain effect originating from the Chern-Simons 3-form. We further find that the DPME has a discontinuous change at a critical value of the phase of the CDW order parameter. We demonstrate that, when there is a jump in the DPME, the surface of the system undergoes a topological quantum phase transition (TQPT), while the bulk remains gapped. Hence, the DPME provides a bulk signature of the boundary TQPT in a TR-invariant Weyl CDW.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1993

'Glitches' in soft X-ray transients: Echoes of the main burst?

Several soft X-ray transients exhibit one or more intensity jumps ('glitches') that interrupt the decay of the initial 'main' burst. We interpret these glitches as due to enhanced mass flow from the companion star which is responding, essentially linearly, to heating by X-rays from the primary. The process goes on continuously, triggered by ('echoing') the initial burst. A time delay T of a few months occurs in the similarly linear flow of matter from the companion surface to the X-ray-emitting inner disk. The time scale in the inner disk is a few days. If this model is correct there is evidence that the main burst, that has been observed to decay over a time approximately less than T, is caused by a burst of mass flow from the companion.

Augusteijn, T.↗

DOE OSTI2024

Methods to Evaluate Subcolumn Profiles Based on Two-Point Diagnostics

In atmospheric models, stochastic generation of subgrid-scale profiles or “subcolumns” has been used for a variety of purposes. Such subcolumns can be generated from subgrid probability density functions (PDFs) at different vertical levels, when such PDFs are available. To do so, the generator needs to decide how strongly points should be correlated in the vertical, that is, how much the values should be overlapped. This is sometimes called “PDF overlap.” To assess vertical correlation in a simplified, observable setting, here the vertical correlation of vertical velocity in subcloud layers is examined. Doppler lidar is used to evaluate the vertical profiles of vertical velocity produced by a large-eddy simulation (LES) model and the Subgrid Importance Latin Hypercube Sampler (SILHS) subcolumn generator. In order to diagnose unrealistic features in subcolumn profiles, various statistical diagnostics are examined here, including the bivariate PDF of vertical velocity at two separated points (i.e., altitudes), the two-point velocity correlation, the integral correlation length, the PDF of two-point velocity differences, and the skewness and kurtosis of two-point velocity differences. The profiles produced by LES match lidar well, except that they are too smooth at small scales. The profiles produced by SILHS exhibit sharp jumps from updraft to downdraft that are not observed in the lidar data. To reduce the generation of these unrealistically sharp jumps, the SILHS sampling method is revised. The diagnostics confirm that the revised sampling method reduces the overprediction of sharp jumps.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1985

Persistence of shocks to large distances in the solar wind

Present hydrodynamic models of solar wind streams predict that interactions will cause interplanetary shocks to decay and large-scale structures to coalesce and smooth out, with a decay length of 10-15 AU for moderate or small-amplitude shocks. The Pioneer 10 plasma data, extending 1-30 AU, are examined in the light of such predictions. It is found that coalescence of streams into a single stream per solar rotation does occur, in general, but that considerable structure remains by 30 AU. The leading edge of a stream often exhibits a velocity jump of greater than 20 km/s; many of these may be shocks. There is a characteristic velocity-density-temperature signature of these distant streams which differs from the close-in double-shock signature. A unique transient was seen in July 1982, at 28 AU, with a velocity jump of about 235 km/s.

Kayser, S. E.↗

NASA NTRS1990

Natural melting within a spherical shell

Fundamental heat transfer experiments were performed on the melting of a phase change medium in a spherical shell. Free expansion of the medium into a void space within the sphere was permitted. A step function temperature jump on the outer shell wall was imposed and the timewise evolution of the melting process and the position of the solid-liquid interface was photographically recorded. Numerical integration of the interface position data yielded information about the melted mass and the energy of melting. It was found that the rate of melting and the heat transfer were significantly affected by the movement of the solid medium to the base of the sphere due to gravity. The energy transfer associated with melting was substantially higher than that predicted by the conduction model. Furthermore, the radio of the measured values of sensible energy in the liquid melt to the energy of melting were nearly proportional to the Stefan number. The experimental results are in agreement with a theory set forth in an earlier paper.

Bahrami, Parviz A.↗

DOE OSTI2022

Modeling the Effects of Drift Orbit Bifurcation on Radiation Belt Electrons

Abstract Drift orbit bifurcation (DOB) has been suggested to play a major role in the loss and transport of radiation belt electrons since it violates the second adiabatic invariants of particles and makes the third invariant undefined. Results from our guiding‐center test particle simulations using the Tsyganenko‐1989c magnetic field model show that the DOB could affect a broad region of the outer radiation belt, which can penetrate inside the geosynchronous orbit at Kp ≥ 3, and its effects are more significant further away from the Earth, at a higher Kp and for higher electron energies. Specifically, the short‐term simulation results after one electron drift show both traditional and nontraditional DOB transport of electrons, with the nontraditional DOB, caused by a third minimum of the magnetic field strength near the equator, reported here for the first time. Moreover, our results show large ballistic jumps in the second invariant and radial distance for electrons at high equatorial pitch angles after one drift. In addition, long‐term DOB transport coefficients of electrons over many drifts are calculated based on our simulation results. We find that the pitch angle and radial diffusion coefficients of electrons due to DOB could be comparable to or even larger than those caused by electron interactions with chorus and Ultra‐Low‐Frequency waves, respectively. In sum, our results demonstrate that DOB could cause effective loss and transport of radiation belt electrons even in the absence of waves.

Astronomy & Astrophysics↗

DOE OSTI2022

Slow Shock Formation Upstream of Reconnecting Current Sheets

The formation, development, and impact of slow shocks in the upstream regions of reconnecting current layers are explored. Slow shocks have been documented in the upstream regions of magnetohydrodynamic (MHD) simulations of magnetic reconnection as well as in similar simulations with the kglobal kinetic macroscale simulation model. They are therefore a candidate mechanism for preheating the plasma that is injected into the current layers that facilitate magnetic energy release in solar flares. Of particular interest is their potential role in producing the hot thermal component of electrons in flares. During multi-island reconnection, the formation and merging of flux ropes in the reconnecting current layer drives plasma flows and pressure disturbances in the upstream region. These pressure disturbances steepen into slow shocks that propagate along the reconnecting component of the magnetic field and satisfy the expected Rankine–Hugoniot jump conditions. Plasma heating arises from both compression across the shock and the parallel electric field that develops to maintain charge neutrality in a kinetic system. Shocks are weaker at lower plasma β, where shock steepening is slow. While these upstream slow shocks are intrinsic to the dynamics of multi-island reconnection, their contribution to electron heating remains relatively minor compared with that from Fermi reflection and the parallel electric fields that bound the reconnection outflow.

79 ASTRONOMY AND ASTROPHYSICS↗