SEARCH · Engineering Papers

Results for “High frequency analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS2000

Computational Aeroacoustic Analysis of Slat Trailing-Edge Flow

An acoustic analysis based on the Ffowcs Williams and Hawkings equation was performed for a high-lift system. As input, the acoustic analysis used un- steady flow data obtained from a highly resolved, time-dependent, Reynolds-averaged Navier-Stokes calculation. The analysis strongly suggests that vor- tex shedding from the trailing edge of the slat results in a high-amplitude, high-frequency acoustic signal, similar to that which was observed in a correspond- ing experimental study of the high-lift system.

Singer, Bart A.↗

NASA NTRS1996

VLBA Imaging of NGC 4261: Symmetric Parsec-scale Jets and the Inner Accretion Region

Dual frequency VLBA observations of the nucleus of NGC 4261 (3C270) reveal highly symmetric radio structures at both 1.6 and 8.4 GHz. Analysis of these images shows that the central 10 pc of this source is not significantly affected by free-free absorption, even though the nucleus of the galaxy is known to contain a nearly edge-on disk of gas and dust. The lack of detectable absorption implies that the density of ionized gas in the central 10 pc is less than (is similar to) 10(sup 3) cm (sup -3), assuming a temperature of (is similar to) 10(sup 4)K.

nuclei↗

NASA NTRS2011

Microcoil Spring Interconnects for Ceramic Grid Array Integrated Circuits

As integrated circuit miniaturization trends continue, they drive the need for smaller higher input/output (I/O) packages. Hermetically sealed ceramic area array parts are the package of choice by the space community for high reliability space flight electronic hardware. Unfortunately, the coefficient of thermal expansion mismatch between the ceramic area array package and the epoxy glass printed wiring board limits the life of the interconnecting solder joint. This work presents the results of an investigation by Marshall Space Flight Center into a method to increase the life of this second level interconnection by the use of compliant microcoil springs. The design of the spring and its attachment process are presented along with thermal cycling results of microcoil springs (MCS) compared with state-of-the-art ball and column interconnections. Vibration testing has been conducted on MCS and high lead column parts. Radio frequency simulation and measurements have been made and the MCS has been modeled and a stress analysis performed. Thermal cycling and vibration testing have shown MCS interconnects to be significantly more reliable than solder columns. Also, MCS interconnects are less prone to handling damage than solder columns. Future work that includes shock testing, incorporation into a digital signal processor board, and process evaluation of expansion from a 400 I/O device to a device with over 1,100 I/O is identified.

Strickland, S. M.↗

NASA NTRS2018

Effect of Distributed Patch of Smooth Roughness Elements on Transition in a High-Speed Boundary Layer

Surface roughness is known to have a substantial impact on the aerothermodynamic loading of hypersonic vehicles, particularly via its influence on the laminar-turbulent transition process within the boundary layer. Numerical simulations are performed to investigate the effects of a distributed region of densely packed, smooth-shaped roughness elements on the laminar boundary layer over a 7-degree half-angle, circular cone for flow conditions corresponding to a selected trajectory point from the ascent phase of the HIFiRE-1 flight experiment. For peak-to-valley roughness heights of 50 percent or less in comparison with the thickness of the unperturbed boundary layer, the computations converge to a stationary flow, suggesting that the flow is globally stable. Analysis of convective instabilities in the wake of the roughness patch indicates two dominant families of unstable disturbances, namely, a high frequency mode that corresponds to Mack mode waves modified by the wake and a lower frequency mode that corresponds to shear layer instabilities associated with the streaks in the roughness wake. Even though the peak growth rate of the later mode is more than 35 percent greater than the peak growth rates of the Mack modes, the latter modes achieve higher amplification ratios, and hence, are likely to dominate the onset of transition, which is estimated to occur slightly later than that in the unperturbed, i.e., smooth surface boundary layer. Additional computations are performed to investigate the effects of various roughness patch configurations on a Mach 3.5 flat plate boundary layer, to help guide an upcoming experiment in the Mach 3.5 Supersonic Low Disturbance Tunnel at NASA Langley Research Center. In this case, the cumulative reinforcement of basic state distortion over the length of the roughness patch is predicted to yield a significantly earlier transition than that over a smooth plate or a plate with a shorter length roughness patch.

Meelan Choudhari↗

NASA NTRS1992

Data analysis and interpretation of lunar dust exosphere

The lunar horizon glow observed by Apollo astronauts and captured on film during the Surveyor mission is believed to result from the scattering of sunlight off lunar fines suspended in a dust layer over the lunar surface. For scale heights on the order of tens of kilometers, it is anticipated that the size of the dust particles will be small enough to admit Rayleigh scattering. Such events would result in scattered light which is polarized to a degree which is a function of observation angle and produce spectra containing large high frequency components ('bluing'). Believing these signatures to be observable from ground based telescopes, observational data has been collected from McDonald Observatory and the task of reduction and analysis of this data is the focus of the present report.

Andrews, George A., Jr.↗

NASA NTRS1993

Investigation of spectral analysis techniques for randomly sampled velocimetry data

It is well known that velocimetry (LV) generates individual realization velocity data that are randomly or unevenly sampled in time. Spectral analysis of such data to obtain the turbulence spectra, and hence turbulence scales information, requires special techniques. The 'slotting' technique of Mayo et al, also described by Roberts and Ajmani, and the 'Direct Transform' method of Gaster and Roberts are well known in the LV community. The slotting technique is faster than the direct transform method in computation. There are practical limitations, however, as to how a high frequency and accurate estimate can be made for a given mean sampling rate. These high frequency estimates are important in obtaining the microscale information of turbulence structure. It was found from previous studies that reliable spectral estimates can be made up to about the mean sampling frequency (mean data rate) or less. If the data were evenly samples, the frequency range would be half the sampling frequency (i.e. up to Nyquist frequency); otherwise, aliasing problem would occur. The mean data rate and the sample size (total number of points) basically limit the frequency range. Also, there are large variabilities or errors associated with the high frequency estimates from randomly sampled signals. Roberts and Ajmani proposed certain pre-filtering techniques to reduce these variabilities, but at the cost of low frequency estimates. The prefiltering acts as a high-pass filter. Further, Shapiro and Silverman showed theoretically that, for Poisson sampled signals, it is possible to obtain alias-free spectral estimates far beyond the mean sampling frequency. But the question is, how far? During his tenure under 1993 NASA-ASEE Summer Faculty Fellowship Program, the author investigated from his studies on the spectral analysis techniques for randomly sampled signals that the spectral estimates can be enhanced or improved up to about 4-5 times the mean sampling frequency by using a suitable prefiltering technique. But, this increased bandwidth comes at the cost of the lower frequency estimates. The studies further showed that large data sets of the order of 100,000 points, or more, high data rates, and Poisson sampling are very crucial for obtaining reliable spectral estimates from randomly sampled data, such as LV data. Some of the results of the current study are presented.

Sree, Dave↗

NASA NTRS2007

Using High Frequency Passive Microwave, A-train, and TRMM Data to Evaluate Hydrometer Structure in the NASA GEOS-5 Data Assimilation System

Validating water vapor and prognostic condensate in global models remains a challenging research task. Model parameterizations are still subject to a large number of tunable parameters; furthermore, accurate and representative in situ observations are very sparse, and satellite observations historically have significant quantitative uncertainties. Progress on improving cloud / hydrometeor fields in models stands to benefit greatly from the growing inventory ofA-Train data sets. ill the present study we are using a variety of complementary satellite retrievals of hydrometeors to examine condensate produced by the emerging NASA Modem Era Retrospective Analysis for Research and Applications, MERRA, and its associated atmospheric general circulation model GEOS5. Cloud and precipitation are generated by both grid-scale prognostic equations and by the Relaxed Arakawa-Schubert (RAS) diagnostic convective parameterization. The high frequency channels (89 to 183.3 GHz) from AMSU-B and MRS on NOAA polar orbiting satellites are being used to evaluate the climatology and variability of precipitating ice from tropical convective anvils. Vertical hydrometeor structure from the Tropical Rainfall Measuring Mission (TRMM) and CloudSat radars are used to develop statistics on vertical hydrometeor structure in order to better interpret the extensive high frequency passive microwave climatology. Cloud liquid and ice water path data retrieved from the Moderate Resolution Imaging Spectroradiometer, MODIS, are used to investigate relationships between upper level cloudiness and tropical deep convective anvils. Together these data are used to evaluate cloud / ice water path, gross aspects of vertical hydrometeor structure, and the relationship between cloud extent and surface precipitation that the MERRA reanalysis must capture.

Robertson, Franklin↗

NASA NTRS1992

High-resolution measurements and analysis of (N-14)(O-16)2 in the (001)-(000) and (011)-(010) bands

High-resolution spectra of NO2 were recorded with a Fourier-transform spectrometer, covering transitions in the (001)-(000) and (011)-(010) bands from 1540 to 1662/cm. The measured line frequencies were used with additional data taken from studies at microwave and far-IR frequencies in an analysis to obtain spin-rotation constants and rotational energies of levels in the (001) and (011) states. Line strengths of these two bands were also measured and analyzed. The analyses included spin-rotation levels of the (001) state for Ka up to and including 13 and N to 73 and those of the (001) state for Ka up to and including 7 and N to 55. The study included observed and enhanced Ka = 5 - 6 transitions in the (020)-(000) band that interact, by means of a Coriolis-type interaction, with Ka = 5 transitions in the (011)-(000) band. Also observed and analyzed were the results of spin-rotation resonance interactions between two levels of the same state. These perturbations affected one or more levels of a given Ka and state and were observed for Ka = 0 with Ka = 2 and Ka = 1 with Ka = 3 for the (001) and (000) states and for Ka = 0 with Ka = 2 for the (011) and (001) states.

Toth, Robert A.↗

NASA NTRS1978

The MOM tunneling diode - Theoretical estimate of its performance at microwave and infrared frequencies

A theoretical analysis of the metal-oxide-metal (MOM) antenna/diode as a detector of microwave and infrared radiation is presented with the experimental verification conducted in the far infrared. It is shown that the detectivity at room temperature can be as high as 10 to the 10th per W Hz exp 1/2 at frequencies of 10 to the 14th Hz in the infrared. As a result, design guidelines are obtained for the lithographic fabrication of thin-film MOM structures that are to operate in the 10-micron region of the infrared spectrum.

Sanchez, A.↗

NASA NTRS2018

Challenges and Opportunities for Subsonic Transport X-Plane Acoustic Flight Research

Aircraft system noise aspects of experimental aircraft acoustic flight research are analyzed. Experimental aircraft are seen as a key development step toward the introduction of a full scale low noise subsonic transport in the future, especially when considering an unconventional aircraft configuration integrating a range of advanced noise reduction technologies. Possible design scenarios for an experimental aircraft are considered where the scale of the experimental aircraft relative to the future, full scale aircraft is likely a major cost driver. Aircraft system noise predictions are presented for a NASA modeled Mid- Fuselage Nacelle subsonic transport concept. The predictions are made for the total airframe system noise at 100, 50, 25, and 12.5% scale of the full scale, future version of the concept, both without and then with a set of noise reduction technologies. The noise reduction technologies include the dual use fairing of the Krueger flap, the continuous mold line for the trailing edge high lift flap, and the pod gear concept for the main gear. The predictions are treated as simulations of flight test measurements of an experimental aircraft that are then processed to full scale as flight data would be. The analysis shows that the combined impact of frequency shift, atmospheric absorption, and background noise cutoff is to establish a realistic upper limit on useful frequency from the experimental aircraft noise. The implications for instrumentation requirements are also noted for high frequency, as well as for the challenge of identifying sources that are reduced significantly by the proposed noise reduction technologies. For the experimental acoustic flight research to be most useful for the objectives of improving the prediction of the future full scale aircraft, it is indicated that the scale should be above 75%. As the demonstrator scale approaches 50%, the limitations become more severe for direct impact to the prediction of the full scale future concept.

Thomas, Russell H.↗

NASA NTRS1975

Analysis of a stability valve system for extending the dynamic range of a supersonic inlet

A stability valve system designed for a full-scale, flight, supersonic, mixed-compression inlet was modeled dynamically by using analog computer techniques. The system uses poppet valves mounted in the inlet cowl to bypass airflow and augments the inlet shock position control system by preventing unstarts caused by high-frequency perturbations. The model was used as a design aid to investigate the effects of varying both the physical configurations of the valve and the flight and wind tunnel conditions. Results of the analysis indicate that the stability valve will provide a bandpass operation of 1 hertz to 17 hertz.

Webb, J. A., Jr.↗

NASA NTRSDate not supplied

Global Analysis of Nonlinear Second-Mode Development in a Mach-6 Boundary Layer From High-Speed Schlieren Data

The second-mode instability on a 7◦ half-angle sharp cone at Mach 6 is analyzed using high-speed calibrated schlieren imagery at a frame rate near the expected fundamental frequency. Experiments were conducted in the NASA Langley 20-Inch Mach 6 facility at unit Reynolds number between 6.56×106 and 9.71×106 m−1. Time-resolved pixel intensity signals throughout the boundary layer are reconstructed using spatially available data in the schlieren images to recover an effective sampling rate of over 10 MHz; these are then converted to quantitative density gradients using a thin-lens-based calibration technique. A global analysis is performed on the schlieren data to investigate the nonlinear growth of the second-mode fundamental and harmonic content. Point-wise measures of the auto-bicoherence are used to identify specific triadic interactions and the locations of their highest levels of quadratic phase coupling. Significant resonance interactions between the second-mode fundamental and harmonic instabilities were found along with interactions between these and the mean flow. Bispectral mode decomposition is employed to educe the flow structures associated with these interactions. A similar analysis is performed for the power spectrum, with power spectral densities computed for each pixel’s time-series and spectral proper orthogonal decomposition employed to derive the modal structure and energy of the flow at specific frequencies. Comparisons between the bispectral quantities and second-mode power show that nonlinear interactions, particularly resonance interactions, are closely correlated with space-time modulation of disturbances during the nonlinear stage of transition.

boundary layer transition↗

NASA NTRS2003

Analyzing Aeroelasticity in Turbomachines

ASTROP2-LE is a computer program that predicts flutter and forced responses of blades, vanes, and other components of such turbomachines as fans, compressors, and turbines. ASTROP2-LE is based on the ASTROP2 program, developed previously for analysis of stability of turbomachinery components. In developing ASTROP2- LE, ASTROP2 was modified to include a capability for modeling forced responses. The program was also modified to add a capability for analysis of aeroelasticity with mistuning and unsteady aerodynamic solutions from another program, LINFLX2D, that solves the linearized Euler equations of unsteady two-dimensional flow. Using LINFLX2D to calculate unsteady aerodynamic loads, it is possible to analyze effects of transonic flow on flutter and forced response. ASTROP2-LE can be used to analyze subsonic, transonic, and supersonic aerodynamics and structural mistuning for rotors with blades of differing structural properties. It calculates the aerodynamic damping of a blade system operating in airflow so that stability can be assessed. The code also predicts the magnitudes and frequencies of the unsteady aerodynamic forces on the airfoils of a blade row from incoming wakes. This information can be used in high-cycle fatigue analysis to predict the fatigue lives of the blades.

Reddy, T. S. R.↗

NASA NTRS1994

The kinetic response of a stochastic plasma to low frequency perturbations

Following suggestion that substorm breakup might be caused by an interchange or ballooning instability, several magnetohydrodynamic (MHD) and gyro-kinetic stability analysis have been performed for plasma sheet magnetic field geometries. However, the stochastic ion dynamics in the highly stressed, thin high-beta near earth plasma sheet violate the locality requirements of MHD and the invarience of the magnetic moment, mu, required by gyro-kinetic theories. In this paper we develop a new linear Vlasov kinetic theory (for low frequency modes omega less than omega(sub b), omega(sub b) being the bounce frequency) which includes the dynamics of stochastic ions.

Hurricane, Omar A.↗

NASA NTRS1982

Solar analysis of solar-constant monitoring package (SMM)

The activity cavity radiometer irradiance monitor is supplying the first high precision data on solar total irradiance at the Earth. Thee classes of variability were discovered: large variations of amplitudes up to 0.2%; small high frequency variations in the form of a continuum in the periodogram, extending up to the Nyquist frequency; and sharp spikes at frequencies corresponding to the individual p modes already known from radial velocity measurements. The observed variations (up to 0.3%, on time scales of several days) were identified with sunspot darkness. The data analysis is expected to give information about the solar interior, as well as about the solar input to the terrestrial climate.

Hudson, H. S.↗

NASA NTRS1981

Analytical verification of undesirable properties of direct model reference adaptive control algorithms

The present investigation is concerned with a new method, called 'final approach analysis', which has been developed to analyze the dynamic properties of a class of direct adaptive control algorithms. Particular attention is given to the robustness of these algorithms to a number of aspects. These aspects are related to the generation of high frequencies in the plant control signal, to excessive bandwidth of the adaptive control loop resulting in excitation of unmodeled dynamics, and, consequently, leading to dynamic instability of the closed-loop adaptive system, and, thirdly, to noise corrupted measurements. The final approach analysis is useful because it can be used in a constructive way to adjust the adaptive gains so as to limit the closed-loop system bandwidth and to ameliorate some of the undesirable characteristics of existing adaptive algorithms.

Rohrs, C. E.↗

NASA NTRSDate not supplied

Ground Tests on the BOLT Geometry at Mach 7: Cross-Facility Comparison and Stability Analysis

Transition measurements have been obtained through two experimental campaigns conducted independently by the German Aerospace Center and the French Aerospace Lab with the French Alternative Energies and Atomic Energy Commission on subscale models of the BOLT-1 flight experiment geometry. This paper details a cross-facility comparison of measurements obtained at Mach 7, as well as subsequent computational analysis. Infrared (IR) thermography measurements obtained by both campaigns have facilitated a global comparison of the transition front across facilities at analagous conditions, which are found to be in good agreement. High-frequency surface pressure fluctuation data demonstrate significant amplification of instabilities with Mack-mode characteristics in the outboard regions of the acreage. These measurements are compared to stability analyses of varying fidelity. The computational methods employed to characterize the boundary-layer transition phenomena include the traditional line-marching implementation of the Parabolized Stability Equations (PSE), 2D eigenvalue analysis coupled with PSE, and Adaptive Mesh Refinement Wavepacket Tracking. While the 2D eigenvalue analysis is found to predict instabilities, which correlate in terms of frequency and acreage location to the experimental measurements, the predicted amplification for these instabilities is lower than would typically be expected for transition. Line-marching results for traveling crossflow produce the best match to the experimental transition front, with a consistent transition N factor of approximately 3-3.5.

Boundary Layer Transition↗

NASA NTRS1988

A selective modal scheme for the analysis of EM coupling into or radiation from large open-ended waveguides

A selective modal scheme is proposed to efficiently analyze the problem of high-frequency (HF) electromagnetic (EM) coupling/penetration into or radiation from open-ended waveguides. This scheme is based on the phenomenon that at sufficiently high frequencies, the modes which contribute most significantly to the fields coupled into the waveguide are those whose modal ray directions are most nearly parallel to the incident-wave direction. This concept is illustrated by calculating the EM radiation and backscattering from open-ended parallel-plate, rectangular, circular, and sectoral waveguide geometries. The calculations use the usual geometrical optics, aperture field, and Ufimtsev edge current techniques. Also included are some measured results which further verify the accuracy of the above computations.

Altintas, Ayhan↗