Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High Explosives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Heavily Confined PBX 9501 Experiment Report FY2020

Most accidental insults to explosives are invariably thermal in nature—either direct thermal via application of heat or indirect thermal when mechanical energy is converted to heat. The key question is whether the initial thermal insult transitions into a violent explosive response. If the ultimate violence attained is moderate, nearby personnel may be harmed or killed, but Inadvertent Nuclear Detonation (IND) will not occur. However, if the explosive ultimately transitions from deflagration to detonation (DDT) then IND becomes a concern. PBX 9501 is not an insensitive high explosive (IHE). It has been conclusively demonstrated that mechanically and thermally damaged PBX 9501 can readily DDT in heavy confinement. However, it is currently unknown whether pristine explosive—i.e. thermally and mechanically undamaged— is capable of DDT. Three experiments were conducted in order to determine whether very heavily confined pristine PBX 9501 is capable of DDT. All experiments used identical 6-inch diameter spherical charges of PBX 9501 confined in a 350 lb. hardened steel vessel with >2.5-inch thick walls. The first, primary experiment tested pristine PBX 9501 and was thermally ignited at the center of using a laser over optical fiber. Two additional baseline experiments were performed for comparison: the second test was initiated at the center using a detonator; the third test was bulk heated until self-ignition (cookoff). Velocimetry data in combination with hydrocode simulations suggest that a classical detonation wave did not develop in the pristine, thermally ignited PBX 9501. Reaction violence was approximately equivalent—in terms of ultimate energy output—as a full detonation, but the acceleration of metal fragments occurred more slowly than in a detonation-driven scenario.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2021

Predicted Reaction Mechanisms, Product Speciation, Kinetics, and Detonation Properties of the Insensitive Explosive 2,6-Diamino-3,5-dinitropyrazine-1-oxide (LLM-105)

2,6-Diamino-3,5-dinitropyrazine-1-oxide (LLM-105) is a relatively new and promising insensitive high-explosive (IHE) material that remains only partially characterized. IHEs are of interest for a range of applications and from a fundamental science standpoint, as the root causes behind insensitivity are poorly understood. In this work, we adopt a multitheory approach based on reactive molecular dynamic simulations performed with density functional theory, density functional tight-binding, and reactive force fields to characterize the reaction pathways, product speciation, reaction kinetics, and detonation performance of LLM-105. We compare and contrast these predictions to 1,3,5-triamino-2,4,6-trinitrobenzene (TATB), a prototypical IHE, and 1,3,5,7-tetranitro-1,3,5,7-tetrazoctane (HMX), a more sensitive and higher performance material. The combination of different predictive models allows access to processes operative on progressively longer timescales while providing benchmarks for assessing uncertainties in the predictions. We find that the early reaction pathways of LLM-105 decomposition are extremely similar to TATB; they involve intra- and intermolecular hydrogen transfer. Additionally, the detonation performance of LLM-105 falls between that of TATB and HMX. We find agreement between predictive models for first-step reaction pathways but significant differences in final product formations. Predictions of detonation performance result in a wide range of values, and one-step kinetic parameters show the similar reaction rates at high temperatures for three out of four models considered.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Free-field Ground Motion Induced by Underground Explosions at Aqueduct Mesa with Predictions for Physical Experiment One (PE1)

We fit standard power-law models for ground acceleration and particle velocity using scaled ground motion observations from underground nuclear explosions at Aqueduct Mesa on the Nevada National Security Site. The models are then validated using small-scale high-explosive (HE) test data from nearby Rainier Mesa. The comparison between model predictions and observations is good and can be made more favorable if the assumed yield for the HE tests are doubled. Further validation is made with a numerical experiment that additionally shows a transition in ground motion attenuation to elastic propagation (1 = r). An extended model is provided to incorporate the long-range transition in attenuation, which results in increased ground motions at farther range. We then make predictions for the field experiment, Physical Experiment One (PE1), to take place in P-tunnel on Aqueduct Mesa, and suggest that the models could be used in planning various operations for PE1.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2021

Empirical Acoustic Source Model for Chemical Explosions in Air

Chemical explosions generate pressure disturbances in air that radiate as nonlinear shock waves near the source and transition into acoustic waves with distance. Because low-frequency acoustic waves generally travel large distances without significant loss of energy, they are often used for explosion monitoring and yield estimation. However, quantitative relationships between acoustic energy and explosion yields are required for accurate yield estimation. Here, we develop an empirical acoustic source model for chemical explosions from experimental data. The empirical model returns the acoustic pressure waveform for the detonation of 1 kg of trinitrotoluene, which is conventionally used to represent the explosive release of 4.184 MJ of explosion energy. The full-waveform model can be used to predict acoustic signals for an arbitrary yield of a high-explosive detonation based on the standard scaling law and to estimate acoustic energies in a specific frequency range. We evaluate the accuracy of the acoustic source model independently by estimating the yield of other explosive events that are not included in the model development. Finally, statistical characteristics of the model and their implications for the uncertainty quantification of estimated yields are discussed.

58 GEOSCIENCES↗
DOE OSTI2014

The Effect of Pore Morphology on Hot Spot Temperature

Composite explosives contain pores that collapse under shock wave interaction generating localized regions of heat known to be important in the initiation of high explosives. Understanding pore collapse under shock loading is essential to create predictive reactive flow models to simulate the initiation process. While spherical pore collapse has been thoroughly simulated, other geometries have been relatively neglected. By simulating microoscale hot spot nucleation in this study, we analyze the effect of pore morphology on the post-shock hot spot temperature. Several pore morphologies that yield higher temperatures than the spherical case are revealed and discussed.

42 ENGINEERING↗
DOE OSTI2026

From atomistic models to machine learning: Predictive design of nanocarbons under extreme conditions

The formation of technologically valuable nanocarbon structures under extreme conditions, such as those produced during high-explosive detonations, remains poorly understood but holds significant potential for the development of controlled synthesis pathways. While detonation shockwaves provide the high-pressure, high-temperature environment required for nanodiamond formation, subsequent cooling and decompression dictate whether the diamond phase is preserved or transformed into other nanocarbon structures. Here, in this study, we employ GPU-accelerated reactive molecular dynamics (ReaxFF) simulations to investigate the graphitization and structural remodeling of detonation nanodiamond under nonlinear quench and pressure-release trajectories. We further investigate how the initial nanodiamond morphology; cuboctahedral, octahedral, or hexagonal prism influences the resulting transformation products. Evolution of nanostructure, allotrope (via simulated x-ray diffraction), carbon hybridization, and ring statistics are tracked during a two-stage quench from 5000 K to 60 GPa. Rapid cooling combined with slow decompression optimizes cubic diamond retention, whereas slow cooling with rapid pressure release promotes surface-to-core graphitization, producing concentric sp 2 -hybridized layers and hollowed inner shells. Octahedral nanodiamonds evolve into carbon nano-onions, initially forming bucky diamonds that progressively transform into fully sp 2 -hybridized structures, while hexagonal prisms preferentially form parallel-stacked graphite layers resembling carbon dots. Transient hexagonal diamond (lonsdaleite) emerges as an interfacial phase, suggesting potential reversibility in the shock-induced graphite-to-diamond transformation pathway transformation route. To extend predictive capabilities, we trained machine learning (ML) regressors on over 10 5 node-hours of molecular dynamics (MD) trajectories. A multilayer perceptron (MLP) model reliably predicts the number of graphitized layers from temperature–pressure trajectories with a coefficient of determination (R 2 ) exceeding 0.90. This high predictive fidelity enables efficient, high-throughput mapping of the synthesis parameter space for optimized graphitization outcomes. Collectively, morphological control combined with optimized quench–decompression conditions promote the selective synthesis of nanocarbon allotropes. This work establishes a data-driven framework for the rational, a priori design of carbon nanomaterials for applications in energy storage, sensing, and biomedicine.

Detonation nanodiamond remodeling↗
DOE OSTI2016

Environmental Restoration of Diesel-Range Organics from Project Chariot, Cape Thompson, Alaska - 16147

Cape Thompson, Alaska, is located approximately 120 miles north of Kotzebue, Alaska, within the Ogotoruk Creek valley. The remote Alaskan location is also home to the US Atomic Energy Commission (AEC) Project Chariot study area. Project Chariot was part of the Plowshare Program, created in 1957 by the AEC to study peaceful uses for atomic energy. Project Chariot began in 1958 when a scientific field team chose Cape Thompson as a potential site to excavate a harbor using a series of nuclear explosions. Between 1959 and 1962, AEC was responsible for over 40 pretest bio-environmental and geotechnical studies of the Cape Thompson area. Strong public opposition to the tests developed, which caused the project to be cancelled with no nuclear explosions ever conducted at the site. In the early 1960's, several deep boreholes were drilled to obtain subsurface, temperature, and high-explosive testing data. Refrigerated diesel was used as a drilling fluid to keep the boreholes open so that thermistors could measure subsurface temperatures. The test boreholes were named Able, Baker, Charlie, Dog, and X-1. In the summer of 2014, the US Department of Energy, Office of Legacy Management (LM) completed the remediation of remnant diesel at these sites. Prior to the 2014 remediation activities, LM conducted two separate characterization field studies to determine the nature and extent of the contamination from the 1960's drilling activities. In 2013, LM developed a remediation plan that was submitted and approved by the Alaska Department of Environmental Conservation (ADEC). The 2014 Project Chariot remediation had some unique logistical challenges and historic issues with stakeholders to overcome. Many of the historic issues centered on previous AEC scientific actions and a general mistrust of the government by the local stakeholders. Prior to and during the 2014 remediation work, an outreach campaign was implemented to discuss prior activities at the site and include stakeholders from Point Hope, Alaska, in the remediation-planning process. The remoteness of the region also provided unique logistical challenges. Because of the short field season, LM initiated several subcontracts over a year in advance. The field camp, heavy equipment, and soil storage containers were shipped by barge to the site. Personnel, food, and small materials were flown in by bush plane from Kotzebue, Alaska. Previous site characterization had identified diesel-range organics (DROs) as the primary contaminant. The cleanup levels for the site were provided by the Alaska Administrative Code (AAC) for the Arctic Zone region. The AAC cleanup level for DROs on gravel pads is 500 mg/kg and 12,500 mg/kg tundra in the arctic-zone region. To help determine the extent and direct soil excavation in the field, photoionization detectors (PIDs) were used for field screening. While the PID results provided rough limits for excavation, laboratory confirmation sampling was required to provide actual excavation guidance. All excavation locations remained open until laboratory results met AAC criteria and ADEC approved closure. The laboratory sample protocol required the bush plane to pick up samples almost daily and transfer them to Anchorage for analysis. In order to meet holding time requirements, all laboratory samples were analyzed on an expedited basis. Analytical results and ADEC approval notifications were e-mailed back to the site via satellite connection. A total of 202 laboratory analyses were needed to complete the remediation effort. At each location (Able, Baker, Charlie, Dog, and X-1), the boreholes were plugged and abandoned in accordance with ADEC regulations. Contaminated soil was excavated, and the material was placed in super-sacks and hauled to connex boxes located near the sea shore. Approximately 786 tons of material was removed and shipped by barge to the Columbia Ridge Landfill in Arlington, Oregon, for disposal. The well casings were cut and sealed below ground surface. Each location was graded to its original contours and reclaimed with native vegetation, and a geodetic survey was conducted. Tours with leaders of the Village of Point Hope and the land owner (Arctic Slope Regional Corporation) were conducted prior to the final demobilization. All remediation equipment and camp facilities were removed at the completion of the project. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

An updated technique to obtain explosive kinetics data on microsecond timescales

There are few techniques available for chemists to obtain time-to-explosion data with known temperature inputs at the early stages of the design and synthesis of new explosives. In the 1960s, a technique was developed to rapidly heat milligram-quantities of confined explosives to ~1000 K on microsecond timescales. Wenograd loaded explosives inside stainless steel hypodermic needles, connected them to a fireset and rapidly discharged a capacitor through the steel. He obtained the temperature by measuring the needle resistance in a Wheatstone bridge arrangement and the time to explosion from a needle rupture. However, owing to the narrow-gauge needles used in the original research, the experiment was only possible with melt-castable explosives; it was never replicated, and modern diagnostics are now available with advances beyond the 1960s. Here, we report the development of the High Explosives Initiation Time (HEIT) test, which utilizes a 250 J pulsed power system to heat the needles. This work extends the Wenograd approach by using optical diagnostics, computational modeling, and advanced techniques to measure needle resistance and needle rupture. Preliminary rate information for pentaerythritol tetranitrate (PETN) will be presented.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2017

SURF Model Calibration Strategy

SURF and SURFplus are high explosive reactive burn models for shock initiation and propagation of detonation waves. They are engineering models motivated by the ignition & growth concept of high spots and for SURFplus a second slow reaction for the energy release from carbon clustering. A key feature of the SURF model is that there is a partial decoupling between model parameters and detonation properties. This enables reduced sets of independent parameters to be calibrated sequentially for the initiation and propagation regimes. Here we focus on a methodology for tting the initiation parameters to Pop plot data based on 1-D simulations to compute a numerical Pop plot. In addition, the strategy for tting the remaining parameters for the propagation regime and failure diameter is discussed.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2021

Reinforced Ammo Can Validation Test Report for Lawrence Livermore National Laboratory

A research effort was conducted to investigate the effects of an unintentional internal detonation of energetic materials on a small transportation container called the “Reinforced Ammo Can” (RAC), which is currently approved for the transport of energetic materials up to 2 grams net explosive weight (NEW) onsite at Lawrence Livermore National Laboratory (LLNL). The project used experimental testing of the containers based on simulated results conducted by a Missouri S & T explosives engineering graduate student while on an internship working in explosives safety at LLNL. The proposed experimental testing consisted of 20 central detonation tests in separate Reinforced Ammo Can containers to verify their high explosive (HE) containment capability. RAC containers are required for transporting secondary explosives on site at LLNL Site 200 in quantities between 300 mg and 2 grams of Trinitrotoluene (TNT) equivalent NEW. Currently, the LLNL Environmental Safety and Health (ES&H) Manual states that the RAC containers are permissible for on-site transportation of secondary explosives up to 2 grams NEW by approved HE handlers with the approval of an Explosives Safety Expert (ESE). Simulated results indicated that tensile failure of the closure mechanism on the container is the most likely failure mode, and showed potential occurrence at the 2 gram NEW threshold. Experimental validation tests were conducted indicating failure/rupture of the containers lid with venting of the detonation products at the 2 gram NEW test threshold with an explosive mass safety factor of 1.3. Failure consisted of impact opening the container latch mechanism resulting in potential ejection of the lid depending on the orientation of the charge within the confinement. This analysis solely is an evaluation of the response of the containment if a detonation were to occur, it does NOT consider the probability of such an event.

42 ENGINEERING↗
DOE OSTI2020

Refractive Imaging of Air Shock Above Microscale Defects in Pentaerythritol Tetranitrate (PETN) Films

Physical vapor deposition (PVD) of high explosives can produce energetic samples with unique microstructure and morphology compared to traditional powder processing techniques, but challenges may exist in fabricating explosive films without defects. Deposition conditions and substrate material may promote microcracking and other defects in the explosive films. Here, we investigate effects of engineered microscale defects (gaps) on detonation propagation and failure for pentaerythritol tetranitrate (PETN) films using ultra-high-speed refractive imaging and hydrocode modelling. Observations of the air shock above the gap reveal significant instabilities during gap crossing and re-ignition.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Beam Profile Measurements at the DARHT II Accelerator Exit

Measurements of the beam profile at the exit of the DARHT II accelerator have been made. The 1.65-kA, 17-MeV DARHT-II linear induction accelerator [1] is unique in that its beam pulse has a long, 1.6-ns flattop during which the kinetic energy varies by less than ±2%. Four short pulses are selected out of this long pulse in the downstream transport [2], and these are converted to bremsstrahlung for multi-pulse flash radiography of high explosive driven hydrodynamic experiments. The objective of the measurements was to demonstrate the capability to make these measurements with a long beam pulse of high intensity. Many observations can be made on the basis of these measurements. These are described herein.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

ESIAS Pseudocode

The Explosive Shock Image Analysis System (ESAIS) is designed to provide a semiautomated quantitative analysis of fast-frame imagery taken during the detonation of high explosive (HE) rate sticks. ESIAS does this by assisting the user in identifying the HE stick geometry on the image (i.e., sides of the undetonated HE stick, detonation front, an axial reference point to assist in the inter-comparison of images); scaling the images based on the known diameter of the undetonated HE stick; identifying the profiles of various surfaces resulting from the detonation process such as the shock wave and product gases or the outer pipe surface; calculating the detonation speed of the HE by tracking the distance it travels between two images with a known time lapse between the images; and determining the slit velocities resulting from the detonation. ESIAS will also import scope traces from oscilloscopes and assist in identifying the time of arrival of significant peaks.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1975

The L = 6.6 Oosik barium plasma injection experiment and magnetic storm of March 7, 1972

A high-explosive shaped charge vaporizing a hollow conical liner of Ba metal and producing a fast field-aligned jet of plasma was detonated at high altitude, during a quiescent phase of a magnetic storm initiated by an ssc 10 hrs prior to the experiment, in an attempt to trace out and observe the dynamics of an auroral field line in the magnetosphere. Observations offer evidence for an upward Birkeland current sheet at the poleward edge of the auroral spiral of 8 x 10 to the minus second power A/m. Unusual features of the substorm leave open the possibility that the plasma injection may have triggered it.

Wescott, E. M.↗
DOE OSTI2020

Comprehensive Data Analysis and Analytic Method Development for PBX9501 Material (FY2019 Annual Report of Aging and Lifetimes Program)

In the polymer bonded explosive (PBX) 9501, a binder consisting of 2.5 wt% nitroplasticizer (NP) and 2.5 wt% Estane R 5703 (Estane) is combined with 94.9 wt% of the high-explosive HMX and 0.1 wt% stabilizer. Because of its flexibility and tensile strength, this binder lowers the sensitivity and improves the manufacturability of PBX 9501. However, like many plasticizers comprised of low molecular weight components, NP has a tendency to diffuse out of the PBX 9501 matrix and can decompose at moderate temperatures into reactive byproducts, such as NO, NO 2 , H 2 O, and HNO x . Through oxidation and hydrolysis, these molecules can further degrade NP and Estane, ultimately degrading the properties of PBX 9501. While gaseous molecules can readily diffuse out of the PBX 9501 charges, the intermediates with lower volatility are more likely trapped in the condensed phase inside the charges and, in a closed system, will co-exist with Estane for an extended period of time creating an ongoing reactive environment. Understanding the rates of formation for these volatiles and intermediates during the NP degradation is therefore a critical prerequisite for understanding the long-term stability of polymeric binders used in munition systems. To work toward this ultimate goal, in the past year, we have conducted comprehensive studies on the physical properties of NP and finished three-year long aging experiment to understand the aging behavior of NP under thermal treatment. Important results are summarized in this annual report. Although NP is widely used in the DOE complex, their physical properties are rather scattered and inconsistent in the open literature. For example, there are at least two widely different values, 14.5°C and -15°C, for the melting point of NP. Although it is known that NP is a eutectic 50:50 mixture of BDNPA and BDNPF, their eutectic phase diagram is not well documented. Furthermore, the effect of temperature on the miscibility between water and eutectic BDNPA/F mixture is rarely reported. To fill these knowledge gaps, a large set of BDNPA/F mixtures with BDNPA concentration ranging from 0 to 100 wt% was analyzed using DSC techniques. In addition to determining the eutectic melt point as -25°C, a phase diagram of the BDNPA/F system was constructed from -30°C to 45°C. With this phase diagram, the phase transition temperatures and composition can be readily found for the BDNPA/F mixtures with various mass ratios.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Formation of bowl-shaped craters

High-explosive charges are used to form, in several types of granular media, laboratory-scale examples of the bowl-shaped craters that are found to be the largest and simplest class of impact structure on planetary and lunar surfaces. High-speed films of the experiments yield crater growth rate and particle displacement data, including quantitative stress, strain, displacement, and velocity data. These results are compared with the particle displacement and velocity data from large explosion experiments which have produced bowl-shaped craters. A time-sequence description of large, bowl-shaped impact crater formation is developed from the results of these comparisons, as well as those of the morphological features and structural deformations of large explosions and impact craters.

Piekutowski, A. J.↗
DOE OSTI2020

Multiphase representation of hotspot formation and growth

Multiphase reacting flow approach has been adopted for modeling of hotspot formation and growth on sub-zonal scale. Mechanical response of the high explosive (HE) is modeled by the Visco-Plastic SCRAM model which includes plastic work, crack growth, and frictional heating along the cracks. In this work a sub-zonal regions with high temperature, hotspots, are modeled as a new phase. Formation and growth of the hotspot phase from the cold phase is modeled as a phase change. Each phase has its own temperature and pressure. Chemical reactions also progress in both phases. The growth of hotspots are determined by the solution of the heat conduction equation with appropriate heat sources due to friction and plastic heating. Sample calculations using the BABBO code show successful detonation calculations with hotspot formation and growth.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Data‐Efficient Generation of Synthetic Microstructures of Polymer‐Bonded Energetic Material With Fine‐Tuned Stable Diffusion

Among current deep learning approaches for synthetic image generation, diffusion-based models stand out in terms of algorithmic stability and ability to retain high-fidelity image features with detailed resolution. Here, in this work, we employ Dreambooth, a method for fine-tuning Stable Diffusion, on X-ray CT images of microstructure of the polymer-bonded form (PBX) of a commonly used high explosive, Pentaerythritol tetranitrate (PETN), which yields generative models for creating synthetic PBX images. The models developed here represent five classes (or ‘lots’) of microstructures and demonstrate successful generation of images of each class with high fidelity, as verified by computed classification accuracy of ∼ 94% or higher. Data augmentation afforded by such image synthesis can be used to more reliably decipher underlying statistics, build processing-structure correlations, recognize off-normal structural anomalies, and identify age-related changes. Ideas related to converting image data into appropriate density mapping and performing mesoscale simulation or surrogate modeling of detonation are also discussed.

Dreambooth↗