Results for “Heat Switch” — Page 22

NASA NTRS1988

Bistable direction switching in an off-axis pumped continuous wave ruby laser

A report is presented of the observation of hysteretic bistable direction switching in a single-mode CW ruby laser system. This effect is only observed when the pump beam which is focused into the ruby rod is misaligned with respect to the rod end faces. At low pump powers, the ruby lases in a mode nearly collinear with the pump axis. At a higher pump power the ruby switches to a mode that is collinear with the rod end faces and preserves the original polarization. The effect is large enough to switch the beam by an angle equal to twice the diffraction angle. The observations show that under steady-state pumping, a CW ruby laser can exhibit bistable operation in its output direction and power. A calculation using the heat equation with two concentric cylinders with one as a heat source (pump laser) and the outer wall of the other held at 77 K, gives an increase in core temperature of about 0.01 K. Therefore, the increase in temperature is not large enough to change the index of refraction to account for such large macroscopic effects.

Afzal, R. Sohrab↗

DOE OSTI2024

LES simulations of a vacuum membrane distillation channel with geometric alterations

3D LES simulations were carried out to study the performance of a vacuum membrane distillation module. A wiggly wall profile with/without embedded stiffeners was considered to alleviate axial and radial temperature polarization, the cause of performance decrease in membrane distillation. Results of the flow field show the wiggles create unsteady vortex shedding inducing intense mixing in the channel. Vortex shedding intensity increases as the Reynolds number increases or stiffeners are added. 3D results show a 56% improvement in flux when moving from a flat sheet membrane to a wiggly membrane with stiffeners at a constant Reynolds number, corresponding to an improvement from 11.7 to 41.7 in the Nusselt number, showing that the alterations improved the flux performance by enhancing the heat transfer along the membrane surface and therefore alleviating temperature polarization, a critical bottleneck in membrane distillation systems. Further, a merit criterion was defined based on the Nusselt number and friction factor, and a 40% increase in merit was shown switching from a flat to a wiggly channel, while a 97% merit increase was seen going from flat to wiggly with stiffeners. A 42% enhancement in the flux was also seen moving from a straight channel to a wiggly channel at a higher Reynolds number which highlights the importance of strategically choosing the mass flow rate, as well as inducing flow separation and vortex shedding in the channel to promote mixing and dissipate the thermal boundary layer. The variation in results between the wiggly module with stiffeners and the wiggly module at high Reynolds numbers suggests enhancing mixing structures can be more impactful on flux for this geometry than increasing the flow rate to a turbulent/transitional regime. However, both are preferable for peak system flux performance. Furthermore, a 2D approximation was used to perform simulations on more extended channels to examine the length degradation. The modules with wiggly channels performed at the same flux level with a doubling of the length. On the other hand, the flat sheet modules experienced length degradation by temperature polarization and dropped in flux yield by around 13% of the short-channel value. This work illustrates that modeling the system and understanding how the performance decreases as the membrane surface area increases are critical for a larger module (scaling up from a lab to a prototype module) to maintain high flux performance.

42 ENGINEERING↗

NASA NTRS1990

Current limiting remote power control module

The power source for the Space Station Freedom will be fully utilized nearly all of the time. As such, any loads on the system will need to operate within expected limits. Should any load draw an inordinate amount of power, the bus voltage for the system may sag and disrupt the operation of other loads. To protect the bus and loads some type of power interface between the bus and each load must be provided. This interface is most crucial when load faults occur. A possible system configuration is presented. The proposed interface is the Current Limiting Remote Power Controller (CL-RPC). Such an interface should provide the following power functions: limit overloading and resulting undervoltage; prevent catastrophic failure and still provide for redundancy management within the load; minimize cable heating; and provide accurate current measurement. A functional block diagram of the power processing stage of a CL-RPC is included. There are four functions that drive the circuit design: rate control of current; current sensing; the variable conductance switch (VCS) technology; and the algorithm used for current limiting. Each function is discussed separately.

Hopkins, Douglas C.↗

DOE OSTI2022

Resistive switching properties of monolayer h-BN atomristors with different electrodes

Resistive switching properties based on molecular beam epitaxy-grown monolayer hexagonal boron nitride (h-BN) atomristors are studied by using metal insulator metal configurations with different electrode materials. Au/monolayer h-BN/Ni devices demonstrate a forming-free bipolar resistive switching (BRS) behavior, a good endurance with up to 97 cycles at a high compliance current of 100 mA, an average on/off ratio of 10 3 , and a low set/reset voltage variability. Metal/monolayer h-BN/graphite/Co devices exhibit self-compliant current BRS characteristics. Both metal/h-BN/Ni and metal/h-BN/graphite/Co devices show the coexistence of BRS, unipolar resistive switching (URS), and nonvolatile threshold switching (TH) modes. The formation of conductive filaments is attributed to the diffusion and trapping of metal ions on the defect sites driven by the electric field, while the rupture is driven by the electric field in BRS and by Joule heating in URS and TH modes.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2023

Tuning anisotropic bonding via chemistry and pressure in layered pnictides and chalcogenides (Final Report)

The overarching goal of this research program, as originally delineated in the proposal “Tuning anisotropic bonding via chemistry and pressure in layered pnictides and chalcogenides” was to develop a predictive, chemistry-driven understanding of the impact of the phonon behavior on thermal properties of bulk layered materials. At finite temperatures, atomic vibrations (phonons) strongly impact the thermodynamics, thermal and electrical transport, and phase-switching properties of functional materials. In particular, soft phonon modes and strongly anharmonic potentials can have spectacular consequences, including structural phase transitions (for example in ferroelectrics and phase-change memory materials), metal-insulator transitions, and extreme thermal resistance preventing heat propagation. Bulk materials with highly-anisotropic bonding may provide unique strategies to induce soft-phonon modes and lattice instabilities. Recently, increasingly detailed investigations of the lattice dynamics in layered materials have been made possible by the advent of first-principles phonon calculations and advanced characterization techniques based on neutron and X-ray scattering. However, due to the lack of studies in which composition and bonding character are systematically varied, there are still fundamental questions regarding the impacts of anisotropic bonding and anharmonicity on lattice stability and thermal transport. One of the major goals of this research program is therefore to address this gap by coherently tuning bonding anisotropy and anharmonicity across families of related compounds. Such approaches have revealed new strategies for exploiting structural anisotropy in quasi-1D and 2D bulk materials to obtain tailored functional properties. This project systematically explored the lattice dynamics, phase stability, and transport properties in bulk layered materials by using both composition and applied pressure to tune the degree of bonding anisotropy and anharmonicity. To accomplish this work, we combined i) single-crystal growth of key material systems with tunable anisotropy, ii) in-situ high-temperature/high-pressure characterization of structure and phonons to probe bonding anisotropy and anharmonicity, including state-of-the-art inelastic X-ray scattering (IXS) and inelastic neutron scattering (INS), and iii) first-principles simulations leveraging large-scale computing to identify the fundamental origins of the observed effects, by relating atomic structure and dynamics to electronic orbital interactions. Finally, we modeled and verified the impact of the phonon behavior on thermal transport to identify new strategies for a-priori design of thermal conductivity. Our integrated collaborative approach helped to systematically unravel the effects of anisotropy and bonding anharmonicity on phonon transport, thermodynamics, and thermal properties of complex anisotropic materials.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Tuning anisotropic bonding via chemistry and pressure in layered pnictides and chalcogenides. Final Report

The overarching goal of this research program, as originally delineated in the proposal “Tuning anisotropic bonding via chemistry and pressure in layered pnictides and chalcogenides” was to develop a predictive, chemistry-driven understanding of the impact of the phonon behavior on thermal properties of bulk layered materials. At finite temperatures, atomic vibrations (phonons) strongly impact the thermodynamics, thermal and electrical transport, and phase-switching properties of functional materials. In particular, soft phonon modes and strongly anharmonic potentials can have spectacular consequences, including structural phase transitions (for example in ferroelectrics and phase-change memory materials), metal-insulator transitions, and extreme thermal resistance preventing heat propagation. Bulk materials with highly-anisotropic bonding may provide unique strategies to induce soft-phonon modes and lattice instabilities. Recently, increasingly detailed investigations of the lattice dynamics in layered materials have been made possible by the advent of first-principles phonon calculations and advanced characterization techniques based on neutron and X-ray scattering. However, due to the lack of studies in which composition and bonding character are systematically varied, there are still fundamental questions regarding the impacts of anisotropic bonding and anharmonicity on lattice stability and thermal transport. One of the major goals of this research program is therefore to address this gap by coherently tuning bonding anisotropy and anharmonicity across families of related compounds. Such approaches have revealed new strategies for exploiting structural anisotropy in quasi-1D and 2D bulk materials to obtain tailored functional properties. This project systematically explored the lattice dynamics, phase stability, and transport properties in bulk layered materials by using both composition and applied pressure to tune the degree of bonding anisotropy and anharmonicity. To accomplish this work, we combined i) single-crystal growth of key material systems with tunable anisotropy, ii) in-situ high-temperature/high-pressure characterization of structure and phonons to probe bonding anisotropy and anharmonicity, including state-of-the-art inelastic X-ray scattering (IXS) and inelastic neutron scattering (INS), and iii) first-principles simulations leveraging large-scale computing to identify the fundamental origins of the observed effects, by relating atomic structure and dynamics to electronic orbital interactions. Finally, we modeled and verified the impact of the phonon behavior on thermal transport to identify new strategies for a-priori design of thermal conductivity. Our integrated collaborative approach helped to systematically unravel the effects of anisotropy and bonding anharmonicity on phonon transport, thermodynamics, and thermal properties of complex anisotropic materials.

36 MATERIALS SCIENCE↗

NASA NTRS1994

Copper Alloy For High-Temperature Uses

Alloy of Cu/8Cr/4Nb (numbers indicate parts by atom percent) improved over older high-temperature copper-based alloys in that it offers enhanced high temperature strength, resistance to creep, and ductility while retaining most of thermal conductivity of pure copper; in addition, alloy does not become embrittled upon exposure to hydrogen at temperatures as high as 705 degrees C. Designed for use in presence of high heat fluxes and active cooling; for example, in heat exchangers in advanced aircraft and spacecraft engines, and other high-temperature applications in which there is need for such material. High conductivity and hardness of alloy exploited in welding electrodes and in high-voltage and high-current switches and other applications in which wear poses design problem.

Dreshfield, Robert L.↗

NASA NTRS2001

High Efficiency Microwave Power Amplifier: From the Lab to Industry

Since the beginnings of space travel, various microwave power amplifier designs have been employed. These included Class-A, -B, and -C bias arrangements. However, shared limitation of these topologies is the inherent high total consumption of input power associated with the generation of radio frequency (RF)/microwave power. The power amplifier has always been the largest drain for the limited available power on the spacecraft. Typically, the conversion efficiency of a microwave power amplifier is 10 to 20%. For a typical microwave power amplifier of 20 watts, input DC power of at least 100 watts is required. Such a large demand for input power suggests that a better method of RF/microwave power generation is required. The price paid for using a linear amplifier where high linearity is unnecessary includes higher initial and operating costs, lower DC-to-RF conversion efficiency, high power consumption, higher power dissipation and the accompanying need for higher capacity heat removal means, and an amplifier that is more prone to parasitic oscillation. The first use of a higher efficiency mode of power generation was described by Baxandall in 1959. This higher efficiency mode, Class-D, is achieved through distinct switching techniques to reduce the power losses associated with switching, conduction, and gate drive losses of a given transistor.

Sims, William Herbert, III↗

DOE OSTI2021

Spatiotemporal characterization of the field-induced insulator-to-metal transition

Watching a metal filament grow Resistive switching is a process in which the electrical resistance of a sample changes abruptly in response to a voltage pulse, often by orders of magnitude. This process is at the heart of many neuromorphic computing approaches but visualizing it in both space and time is tricky. del Valle et al . monitored the resistive switching in three different vanadium oxide compounds by measuring time- and space-resolved optical reflectivity (see the Perspective by Hilgenkamp and Gao). A characteristic conducting filament was quickly nucleated on the inhomogeneities in the sample and then propagated due to Joule heating. —JS

Science & Technology - Other Topics↗

NASA NTRS1972

Experimental studies and applications of vanadium oxides.

The electrical and electrochemical properties of V-5 and V-7 vanadium oxides were investigated. The effects of pressure, temperature and moisture on the bulk resistivity of the oxides in powder, sintered, and crystalline form were determined, and the static and dynamic volt-ampere characteristics were obtained. Sintered samples tested showed better electrical stability than the compressed powder samples. Two types of commercially available vanadium pentoxide were heat-treated to obtain various crystalline oxide forms which were mounted on alumina substrates and terminated by thick-film conductors for making electrical connections. Indications are that these materials could have applications as sensors, critical-temperature resistors, high-speed switches, and temperature-compensation elements in hybrid microelectronic circuits.

Williams, L., Jr.↗

NASA NTRS1973

ERTS-1 - Toward global monitoring.

The satellite has a near-polar orbit with a mean altitude of about 547 n. mi. On the average six million square kilometers are mapped daily. The multispectral scanner and other essential systems on board the satellite have suffered no detectable degradation since the early failures of a circuit switch and one of the two tape recorders. A year of ERTS-1 experience has shown that many applications can be mechanized with the present instrumentation. New investigations planned for future satellites are discussed, giving attention to pollution monitoring, geological studies, heat-balance surveys, and the analysis of damage caused by storms and earthquakes.

Fletcher, J. C.↗

NASA NTRS1990

Galileo spacecraft power management and distribution system

The Galileo PMAD (power management and distribution system) is described, and the design drivers that established the final as-built hardware are discussed. The spacecraft is powered by two general-purpose heat-source-radioisotope thermoelectric generators. Power bus regulation is provided by a shunt regulator. Galileo PMAD distributes a 570-W beginning of mission (BOM) power source to a user complement of some 137 load elements. Extensive use of pyrotechnics requires two pyro switching subassemblies. They initiate 148 squibs which operate the 47 pyro devices on the spacecraft. Detection and correction of faults in the Galileo PMAD is an autonomous feature dictated by requirements for long life and reliability in the absence of ground-based support. Volatile computer memories in the spacecraft command and data system and attitude control system require a continuous source of backup power during all anticipated power bus fault scenarios. Power for the Jupiter Probe is conditioned, isolated, and controlled by a Probe interface subassembly. Flight performance of the spacecraft and the PMAD has been successful to date, with no major anomalies.

Detwiler, R. C.↗

NASA NTRS2010

Two-Phase Thermal Switching System for a Small, Extended Duration Lunar Surface Science Platform

This paper describes a novel thermal control system for the Warm Electronics Box (WEB) on board a small lunar surface lander intended to support science activities anywhere on the lunar surface for an extended duration of up to 6 years. Virtually all lander electronics, which collectively dissipate about 60 W in the reference mission, are contained within the WEB. These devices must be maintained below 323 K (with a goal of 303 K) during the nearly 15-earth-day lunar day, when surface temperatures can reach 390K, and above 263 K during the nearly 15-earth-day lunar night, when surface temperatures can reach 100K. Because of the large temperature swing from lunar day-to-night, a novel thermal switching system was required that would be able to provide high conductance from WEB to radiator(s) during the hot lunar day and low (or negligible) conductance during the cold lunar night. The concept that was developed consists of ammonia variable conductance heat pipes (VCHPs) to collect heat from WEB components and a polymer wick propylene loop heat pipe (LHP) to transport the collected heat to the radiator(s). The VCHPs autonomously maximize transport when the WEB is warm and autonomously shut down when the WEB gets cold. The LHP autonomously shuts down when the VCHPs shut down. When the environment transitions from lunar night to day, the VCHPs and LHP autonomously turn back on. Out of 26 analyzed systems, this novel arrangement was able to best achieve the combined goals of zero control power, autonomous operation, long life, low complexity, low T, and landed tilt tolerance.

Bugby, David C.↗

DOE OSTI2025

In Situ Study of Resistive Switching in a Nitride‐Based Memristive Device

Abstract Resistive switching (RS) devices with ultra‐low‐voltage threshold and reliable switching repeatability exhibits great potential applications in energy‐efficient data storage and neuromorphic computing. Understanding switching mechanisms at nanoscale is critical to design RS devices with improved performance. In this work, a lamella memristive device using focused ion beam (FIB) method based on the metal/TiO x /TiN/Si structure device is fabricated. In situ transmission electron microscopy (TEM) and current–voltage ( I–V ) characteristic demonstrate that the lamella device shows a volatile RS behavior with a threshold switching at ≈ ± 0.4 V. In situ scanning transmission electron microscopy (STEM) experiments with electron energy loss spectroscopy (EELS) reveal that the charge carriers such as oxygen vacancies migrate under positive/negative DC bias and modulate Schottky barriers at the top and bottom metal/semiconductor interfaces. The RS mechanism of the lamella device is based on the Schottky barriers modulation and Joule heating assisted electric field triggered thermal runaway (FTTR) occurred at the metal/semiconductor interfaces. The fundamental insights gained from this study presents a perspective on interface‐type RS devices processing and opens up new technological opportunities of fabricating ultra‐low‐energy memristive devices.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Scalable electrified cementitious materials production and recycling

The production of Portland cement, the industry-standard cement, contributes ~8% of global CO 2 emissions through fossil-fuel heating and decomposition of limestone (the primary cement raw material). Decarbonization, e.g., via direct electrification, of this 200-year-old liming routine is extremely challenging at the industry scale. We propose a scalable electrochemical decarbonization approach to circumvent the limestone use by switching to carbon-free calcium silicates from abundant minerals and recycled concrete. Water electrolysis produces protons and hydroxides to drive a pH gradient that accelerates Ca 2+ ion leaching from calcium silicates and captures atmospheric CO 2 to form carbon-negative CaCO 3 , which serves as the feedstock for cement manufacturing or as the carbon-mineralized product for cement substitution with permanent carbon storage. Value-added co-products amorphous silica and green H 2 further enhance cement performance and supplant fossil fuels for net-zero transition, respectively. The products readily meet present-day regulatory standards and demands, and the approach readily synergizes with business-as-usual cement manufacturing and concrete construction, which are important for upscaling and structural safety, promising ready reception by the public and industries. Blended Portland cement produced through our approach with carbon-negative CaCO 3 and silica demonstrates enhanced resilience and achieves carbon neutrality or negativity when incorporating storage or circulation of CO 2 from cement plant flue gas, respectively. This low-cost, electrochemical cement production approach using abundant ubiquitous raw materials enables electrification, transition to clean fuel, and decarbonization at a gigaton scale.

36 MATERIALS SCIENCE↗

NASA NTRS1985

Dynamic Thermophysical Measurements in Space

The objective is to develop techniques for the dynamic measurement of selected thermophysical properties (e.g., heat of fusion, heat capacity, electrical resistivity) of solids and liquids at temperatures above 2000 K in a near zero-gravity environment. The first phase involves establishing the stability (geometrical) limits of specimens when rapidly heated to temperatures beyond their melting point. A test equipment package was designed and constructed for this purpose, consisting of removable specimen cartridge cells, a battery-bank power supply, a high-speed framing camera, a single-wavelength pyrometer, and electronic switching and control equipment. The operation of the equipment package was tested in the laboratory in preparation for near zero-gravity experiments to be performed during a KC-135 flight in September, 1984.

Cezairliyan, A.↗

NASA NTRS1994

SLR 2000

SLR 2000 is a concept for a totally automated subcentimeter SLR system presently being studied at GSFC. If funding permits, a prototype would be installed and tested at the Goddard Geophysical and Astronomical Observatory (GCAO) in FY98 and a small number of automated stations would be fielded by the year 2000. Unlike present systems, the "SLR 2000" system is being designed to: 1) operate autonomously without the need for onsite operators; 2) present no hazards (i.e., optical, electrical, and/or chemical) to personnel in the vicinity or to overflying aircraft; and 3) have a mean time between failures (MTBF) of at least three months. It is assumed that the systems are located at "friendly" sites where some level of security is provided and where certain low level service functions (e.g. commercial power, communications, heat pump service cleaning, etc.) are available or can be contracted for locally on an as-needed basis. The main system consists of two parts - an optical head and electronics rack. The optical head contains the laser transmitter and power supply, transmit/receive switch, optical telescope, tracking angle sensor (intensified CCD camera), detector and power supply, two angular encoders, azimuth and elevation motors, and a protective dome. The optical head mounts directly to the top of a concrete pier which contains the geodetic monument and forms part of the environmental housing for the hardware and servicing personnel. It is equipped with electronic levels for leveling the mount and monitoring its stability.

Degnan, John J.↗

NASA NTRS1993

Power Switching Device

The MOS-Controlled Thyristor is a new type of power switching device for faster and more efficient control and management of power electronics. It enables power electronic switching at frequencies of 50 to 100 thousand times a second with much lower power losses than other semiconductor devices. Advantages include electric power savings and smaller space. The device is used in motor and power controllers, AC & DC motor drives and induction heating. Early development was supported by Lewis Research Center (LEW) and other agencies. General Electric''s power semiconductor operation, the initial NASA contractor, was later purchased by Harris Semiconductor.

Source record↗