SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ozone mixing ratios in ppb are measured using a Teledyne API Model T400U. The analyzer uses UV absorption at 254 nm to determine O3 concentration. Sampled air was pulled from above the Naval Postgraduate School’s (NPS) Twin Otter aircraft through a rear-facing, ¼” OD PFA Teflon tube. The sample stream was split between several other gas analyzers (CO, NOx, and H2O) and an oxidation flow reactor. The data were recorded at 0.1 Hz.
ABSTRACT Emission line observations together with photoionization models provide important information about the ionization mechanisms, densities, temperatures, and metallicities in active galactic nuclei (AGN)-ionized gas. Photoionization models usually assume Maxwell–Boltzmann (M–B) electron energy distributions (EED), but it has been suggested that using κ distributions may be more appropriate and could potentially solve the discrepancies in temperatures and abundances found in HII regions and planetary nebulae. We consider the impact of the presence of κ distributions in photoionized nebulae associated with AGN and study how this might affect spectral modelling and abundance analyses for such regions. Using the photoionization code MAPPINGS 1e, we compute models adopting M–B and κ distributions of electron energies and compare the behaviour of emission line ratios for different values of κ, gas metallicity, density, ionization parameter, and SED slope. We find that the choice of EED can have a large impact on some UV and optical emission lines emitted by photoionized nebulae associated with AGN, and that the impact of adopting a κ distribution is strongly dependent on gas metallicity and ionization parameter. We compile a sample of line ratios for 143 type 2 AGN and compare our models against the observed line ratios. We find that for 98 objects, κ distributions provide a better fit to the observed line ratios than M–B distributions. In addition, we find that adopting κ-distributed electron energies results in significant changes in the inferred gas metallicity and ionization parameter in a significant fraction of objects.
By 2050, shale gas production is expected to exceed three-quarters of total US natural gas production. However, current unconventional hydrocarbon gas recovery rates are only around 20%. Maximizing production of this natural resource thus necessitates improved understanding of the fundamental mechanisms underlying hydrocarbon retention within the nanoporous shale matrix. In this study, we integrated molecular simulation with high-pressure small-angle neutron scattering (SANS), an experimental technique uniquely capable of characterizing methane behavior in situ within shale nanopores at elevated pressures. Samples were created using Marcellus shale, a gas-generative formation comprising the largest natural gas field in the United States. Our results demonstrate that, contrary to the conventional wisdom that elevated drawdown pressure increases methane recovery, a higher peak pressure led to the trapping of dense, liquid-like methane in sub-2 nm radius nanopores, which comprise more than 90% of the measured nanopore volume, due to irreversible deformation of the kerogen matrix. These findings have critical implications for pressure management strategies to maximize hydrocarbon recovery, as well as broad implications for fluid behavior under confinement.
A flow cell is a necessary measurement interface for some important optical analyzers. In our application of the flow cell, we utilize a state-of-the-art optical analyzer (Malvern Insitec) to measure particle size distribution and concentration in-situ in a sampled flow from a novel pressurized oxygen-fuel combustion process. However, since this sampling flow is a flow of moist flue gas under high temperature and pressure, and the flow contains particles and corrosive acid gases, it is an extreme challenge to obtain a flow cell with a high optical quality that does not perturb the measurement. To address this challenge, we propose a new design for an optical flow cell. By using a unique flow field in the proposed flow cell, the measurement zone can be well defined by the sampling flow, minimizing the influence of purge flow. To demonstrate this flow cell, we have built a test system, and conduct measurements utilizing polydisperse-particle standards (10-100 µm and 1-10 µm). The results reveal that the optical windows are well protected by the purge flow field, without risk of deposition from the sampling flow, and the Malvern Insitec can measure the particle size distribution by using this flow cell, without generating sample bias.
Summary This study continues the work of presenting a novel approach for making petrophysical assessments of tight core samples. This method, the full-immersion pressure-pulse decay (Hannon 2019), involves applying a rapid increase in pressure in a chamber surrounding the entire outer surface area of a cylindrical sample, shutting the system in, and monitoring the pressure decay in the chamber as it reaches a new equilibrium. A precursor article covered the numerical simulator designed to model flow through the sample, demonstrating its performance and accuracy in addition to providing a first-order comparison between the speed and shape of the pressure-decay responses of the full-immersion method with those of other similar transient methods. This study covers the parameter-estimation procedure and experimental verification through a proof-of-concept laboratory investigation. The investigations provided here demonstrate that under appropriate, achievable experimental conditions, the pressure data can be analyzed in such a way that returns an estimate of the porosity and apparent permeabilities both parallel and perpendicular to bedding from a single test performed on a single cylindrical sample. After determining these experimental conditions (the uniqueness window), this report outlines a data-inversion strategy to estimate the petrophysical properties (porosity, horizontal permeability, and vertical permeability) from each test. This strategy is put to the test through comparisons with measurements performed by a commercial core laboratory. A common set of samples recovered from an outcrop of a tight-gas sandstone formation were investigated using the full-immersion method, and their results are compared with those from conventional steady-state measurement procedures performed by the commercial laboratory. Comparisons between petrophysical characterizations of these samples, which had permeabilities between 25 nd and 2.3 μd, demonstrated close agreement in most cases. However, whereas steady-state measurements performed at the professional laboratory required 4 to 5 hours of testing time per measurement of a single permeability, similar assessments using the full-immersion technique, requiring approximately 5 to 10 minutes to complete, returned estimates of the horizontal and vertical permeability simultaneously. Additional analyses are provided to determine principal reasons of discrepancies in instances where agreement was not as strong. Based on lessons learned from these experiences, the report closes with suggestions on areas of improvement in the experimental approach. Once complete, these developments should propel this technology to fill a critical need to determine petrophysical properties (porosity and permeability) of tight rocks in a time-efficient manner and in a way that does not compromise their accuracy.
Chromium-coated zirconium alloy cladding is under investigation as an accident-tolerant fuel (ATF) concept to extend performance to higher burnups via improved oxidation resistance and reduced hydrogen pickup. However, hydrothermal corrosion behavior and hydrogen transport mechanisms governing in-service hydriding of these coatings remain poorly understood. In a collaborative study between Pacific Northwest National Laboratory (PNNL), Idaho National Laboratory (INL), and the University of Huddersfield, cold spray (CS) and physical vapor deposition (PVD) Cr-coated Optimized ZIRLO™ cladding samples were characterized after exposure to PWR-simulated water chemistry under both in-core (neutron irradiation) and out-of-core (aqueous-only) conditions at the MIT Research Reactor. Multi-scale characterization was performed independently at PNNL and INL to evaluate coating integrity, microstructural evolution, Cr/Zr interface chemistry, and hydride formation. Both laboratories observed a consistent divergence in hydriding behavior: out-of-core CS Cr-coated cladding exhibited elevated hydride concentrations exceeding those of uncoated cladding, whereas in-core CS samples showed substantially suppressed hydriding. In-core specimens also displayed irradiation-specific features, including nanoscale voids within the Cr coating and radiation-induced segregation clusters in the Zr substrate. CS coatings retained an interdiffusion-free Cr/Zr bond with no intermetallic layer, whereas PVD coatings exhibited inferior quality with visible cracks and pores. An automated image-based hydride quantification method systematically overestimated bulk hydrogen content relative to inert gas fusion measurements, underscoring the need for standardized sample preparation and reference standards. Interpretation of hydride nucleation and growth is complicated by the open inner-diameter of the specimens, which provides additional hydrogen pathways. The results motivate further foundational studies to support predictive models of hydrothermal corrosion and hydrogen transport in unirradiated and irradiated Cr-coated cladding.
This report examines the household-level energy impacts of residential property assessed clean energy (R-PACE) projects using normalized metered energy consumption methods. Our analysis covers projects that occurred through an R-PACE program between 2009 and 2017 and includes more than 25,000 electricity meters and 15,000 gas meters. We employ a comparison group, drawn from other R-PACE households with similar locational and usage characteristics whose projects were implemented at different times, to control for some non-project and non-weather factors that may impact energy use. We find that projects consisting of energy efficiency technologies save, on average, about 3% of household electricity usage and 3.5% of household gas usage. R-PACE financing, however, can be used to install central heating or air conditioning equipment for the first time. These projects would be expected to increase energy consumption. Since our data do not directly indicate which projects are new installations, we develop a simple algorithm for identifying them. Removing these inferred installation projects yields average savings of about 5% for electricity and 6% for gas for those households that remain in the sample. Given the mild California climate and the results of another study of similar California projects using similar methods, these results are in line with expectations. Solar PV projects yield large reductions in grid electricity use, averaging 69% of household consumption. We estimate that, collectively, all R-PACE projects installed in California through 2019 would generate annual reductions in grid-tied electricity consumption of 506 GWh (mostly due to solar PV) and gas consumption reductions of 2 million therms in a normal weather year. These impacts are equivalent to the electricity consumption of about 74,000 California households (including both efficiency and PV generation) and the gas consumption of about 4700 California households.
Polymers of intrinsic microporosity (PIMs) offer tantalizing combinations of high selectivity and permeability in initial gas permeation measurements. Here, we report characterization of pure- and mixed-gas permeation properties of a thick (~80 μm) PIM consisting of Tröger's Base (TB) and Ethanoanthracene (EA) films. The effects of feed pressure and temperature on pure-gas permeabilities of CH 4 , N 2 , O 2 , H 2 , and CO 2 were investigated. The physical aging behavior of the thick film was tracked via pure-gas O 2 , N 2 , and CH 4 permeability at 35 °C. Gas permeability decreased noticeably and selectivity increased as aging time increased. Particular attention was given to mixed-gas measurements of CO 2 and CH 4 (50/50) permeabilities at 35 °C and fugacities ranging from 2 to 18 atm to explore whether the rigid, bridged, bicyclic TB and EA units could resist CO 2 -induced plasticization. These results are presented along with pure-gas CO 2 and CH 4 results for membrane samples aged at different times. PIM-EA-TB aged for ~24 h did not show signs of plasticization across the fugacity range considered. Furthermore, dual-mode competitive sorption presumably caused the CO 2 /CH 4 mixed-gas selectivity to be slightly higher than its corresponding pure-gas selectivity. However, as aging time increased, aged films underwent progressively more rapid and extensive CO 2 -induced plasticization with increasing fugacity, suggesting a systematic relationship between physical aging and plasticization in PIMs. Consequently, physical aging caused less improvement in mixed-gas CO 2 /CH 4 selectivity than it did in pure-gas selectivity, due mainly to plasticization effects.
Understanding the nature of fluid flow through fractured wellbore cement is fundamental for evaluating the leakage potential and risk assessments of leaky wellbores. In this study, the conditions that require considering visco-inertial flow for describing the gas flow through wellbore cement fractures were investigated. Nitrogen gas flow tests were conducted on fractured cement samples under varying pressure conditions and flow rates, covering both viscous and visco-inertial flow regimes. The data substantially deviated from Darcy's law at higher flowrates and were well-fit to Forchheimer's equation for visco-inertial flow. The inertial coefficient and critical Reynolds number were expressed as a function of the hydraulic aperture. Finally, the empirical function obtained from the experiments was used as an input to numerical simulations which showed the significant role of visco-inertial flow in wellhead pressure build-up and leakage rates, and demonstrated the importance of visco-inertial flow when modeling gas flow through wellbore cement fractures.
The study of lipid molecular fossils by traditional biomarker analysis requires bulk sample crushing, followed by solvent extraction, and then the analysis of the extract by gas chromatography-mass spectrometry (GC–MS). This traditional analysis mixes all organic compounds in the sample regardless of their origins, with a loss of information on the spatial distribution of organic molecules within the sample. These shortcomings can be overcome using the chemical mapping of intact samples. Spectroscopic techniques such as UV fluorescence or Raman spectroscopy, laser ablation inductively coupled plasma mass spectrometry, and time-of-flight secondary ion mass spectrometry (ToF-SIMS) are among those elemental and molecular mapping techniques. This study employed femtosecond (fs) laser ablation combined with single-photon ionization, a method called fs-laser desorption postionization mass spectrometry (fs-LDPI-MS). In this work, a pulsed ~75 fs, 800 nm laser was used to ablate the geological sample, which was then photoionized after a few microseconds by a pulsed 7.9 eV vacuum ultraviolet laser. An organic carbon-rich geological sample was used for this study to map hydrocarbon biomarkers in sediments that were previously studied by GC–MS. The petrography of this sample was examined by optical and fluorescence microscopy. It is demonstrated here that fs-LDPI-MS combined with petrography for multimodal imaging can expose buried compounds within the sample via in situ layer removal. When used in conjunction with traditional organic geochemical analysis, this method has the potential to determine the spatial distribution of organic biomarkers in geological material. Finally, fs-LDPI-MS imaging data are compared with ToF-SIMS imaging that is commonly used for such studies.
The DOE R&D program under the Spent Fuel Waste Science Technology (SFWST) campaign has made key progress in modeling and experimental approaches towards the characterization of chemical and physical phenomena that could impact the long-term safety assessment of heat-generating nuclear waste disposition in deep clay/shale/argillaceous rock. International collaboration activities such as heater tests and postmortem analysis of samples recovered from these have elucidated key information regarding changes in the engineered barrier system (EBS) material exposed to years of thermal loads. Chemical and structural analyses of sampled bentonite material from such tests has as well as experiments conducted on these are key to the characterization of thermal effects affecting bentonite clay barrier performance and the extent of sacrificial zones in the EBS during the thermal period. Thermal, hydrologic, and chemical data collected from heater tests and laboratory experiments has been used in the development, validation, and calibration of THMC simulators to model near-field coupled processes. This information leads to the development of simulation approaches (e.g., continuum vs. discrete) to tackle issues related to flow and transport at various scales of the host-rock and EBS design concept. Consideration of direct disposal of large capacity dual-purpose canisters (DPCs) as part of the back-end SNF waste disposition strategy has generated interest in improving our understanding of the effects of elevated temperatures on the EBS design. This is particularly important for backfilled repository concepts where temperature plays a key role in the EBS behavior and long-term performance. This report describes multiple R&D efforts on disposal in argillaceous geologic media through development and application of coupled THMC process models, experimental studies on clay/metal/cement barrier and host-rock (argillite) material interactions, molecular dynamic (MD) simulations of water transport during (swelling) clay dehydration, first-principles studies of metaschoepite (UO 2 corrosion product) stability, and advances in thermodynamic plus surface complexation database development. Drift-scale URL experiments provides key data for testing hydrological-chemical (HC) model involving strong couplings of fluid mixing and barrier material chemical interactions. The THM modeling focuses on heater test experiments in argillite rock and gas migration in bentonite as part of international collaboration activities at underground research laboratories (URLs). In addition, field testing at an URL involves in situ analysis of fault slip behavior and fault permeability. Pore-scale modeling of gas bubble migration is also being investigated within the gas migration modeling effort. Interaction experiments on bentonite samples from heater test under ambient and elevated temperatures permit the evaluation of ion exchange, phase stability, and mineral transformation changes that could impact clay swelling. Advances in the development, testing, and implementation of a spent nuclear fuel (SNF) degradation model coupled with canister corrosion focus on the effects of hydrogen gas generation and its integration with Geologic Disposal Safety Assessment (GDSA). GDSA integration activities includes evaluation of groundwater chemistries in shale formations.
Time-of-flight secondary-ion mass spectrometry (TOF-SIMS) and atom probe tomography (APT) have many similarities. Both detect the chemical makeup of a solid material at ppm or better sensitivity, while retaining the spatial location information from the signal. Both use a similar principle to measure a signal associated with a given charged secondary ion—the flight time it takes a secondary ion to reach the detector after it is generated. Both are destructive techniques—albeit destructive of very small volumes—because the signal measured is generated by the removal of material from the sample itself. Importantly, both techniques require ultra-high vacuum (UHV) to ensure that the secondary ions, once generated, can reach the detector without collision with other atoms in the gas phase. In the case of TOF-SIMS, the samples can vary from several mm to several inches in size, whereas for APT, the samples are cones several hundred microns in size that are prepared in a special manner (covered in detail later in the chapter). We will discuss the basic fundamentals of each technique and cover several examples of the technique applied to photovoltaic materials, which should give a good idea of the types of information one can gain from TOF-SIMS and APT and how they are complementary as they both operate at different length scales: at the hundreds of microns to hundreds of nanometer scale for TOF-SIMS and at the nanometer to a few angstroms scale for APT.
Zircaloy-4 and AISI 347 stainless steel were irradiated to low doses (10 20 and 10 21 n/cm 2 ) at low temperature (~60°C) in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). These materials were under consideration for some of the structural components of the medical isotope production facility developed by SHINE Technologies. Zircaloy-4 base metal, as welded, welded and post-weld heat treated (PWHT), and hydrogen charged samples were irradiated. AISI 347 base metal from Sandmeyer Steel, Penn Stainless, and Rolled Alloys suppliers were irradiated. AISI 347 gas tungsten arc welding (GTAW) and flux-cored arc welding (FCAW) samples of Penn Stainless and Rolled Alloys were also irradiated. The irradiated materials were tested with microhardness and tensile tests at room temperature in air. The AISI 347 materials had more elongation after irradiation than the Zircaloy-4 materials. In fact, the Zircaloy-4 welded without PWHT and with H charging had the lowest elongation of any of the materials. This report is the final in a series of reports on this project.
Studying the kinematics and mass modelling of galaxies from H i 21 cm data provides valuable insights into the properties of both the baryonic components and the dark matter halo in nearby galaxies. Despite many observational studies, mass modelling of galaxies remains challenging due to different limitations. For example, most of the previous studies involving mass modelling are based on rotation curves derived from 2D velocity fields from H i or H α spectroscopic observation which are often affected by beam smearing and projection effect. However, kinematic modelling done by fitting the ‘Tilted ring model’ to 3D data cube is not affected by these issues. In this study, we present and compare 3D kinematic modelling of a pilot sample of 11 galaxies from the GMRT archive atomic gas survey (GARCIA) using two different publicly available pipelines. We model the observed H i rotation curve using 3.6-μm infrared data and SDSS r-band data for stellar contribution, H i surface density profile for gas, and Navarro–Frenk–White profile for dark matter halo; and employ the Markov chain Monte Carlo optimization method for parameter estimation. Further, to validate our analysis, we revisit important scaling relations, e.g. the M gas –M star relation, M star –M halo relation, M gas –M halo relation and Baryonic Tully–Fisher relation. Here, the scaling relations from our analysis are broadly consistent with that reported in the literature. A larger sample of galaxies from GARCIA in the near future will allow studying these scaling relations in greater details.
Catalytic pyrolysis of methane (CH4) is a promising approach to generate hydrogen (H2). The apparent activation energy of this process has a significant influence on the efficiency and required temperature for H2 generation. Preliminary experiments indicate that minerals present in shales have catalytic effects during in-situ H2 generation from shale reservoirs under electromagnetic (EM) heating. However, the quantitative role of such natural catalysts on apparent activation energy is not explored yet. This research evaluated the role of reservoir rock (shale) in EM heating and on the apparent activation energy of methane pyrolysis (MP) for in-situ H2 generation. Experiments are conducted in a customized EM reactor with frequency 2.45 GHz, and reaction temperature and generated gases are measured by a real-time IR pyrometer and gas analyzer, respectively. It is found that shale samples experienced thermal runway (TR) at 420 ºC under 0.15 kW EM power without any artificial heating promoter. In the presence of spent shale, CH4 conversion started approximately at 600 ºC with negligible amount of carbon dioxide (CO2) generated during this process. We further calculated apparent reaction order and apparent activation energy for MP process in the presence of shale under EM heating, which are 0.4357 and 98.12 kJ/mol, respectively. This research paves a way for leveraging the role of minerals as natural catalysts for enhancing H2 generation under EM heating in petroleum reservoirs.
While ion mobility coupled to mass spectrometry (IMS/MS) has been increasingly adapted to biological analysis, the structural and molecular specificity offered by IMS/MS has untapped potential for creating novel materials (for energy, catalysis, biomolecular switches etc.) with rationally tailored properties by precisely controlling the chemical structure and composition of these materials. While electrochemical and catalytic properties of the bulk material are understood by mass-selective ion-soft-landing, different structures of one molecule can exhibit distinct properties from the bulk. Many biological phenomenon occur at interfaces and are highly structurally specific. IMS/MS offers means to separate molecules in a sample (which is first ionized and released to gas phase from the condensed phase) based on mass and structure. Species thus separated can potentially be deposited onto surfaces with molecular and structural specificity, to perform fundamental investigations for understanding critical interfacial phenomenon. Key performance metrics for IMS/MS analysis are resolution of separations and sensitivity. Recently developed Structures for Lossless Ion Manipulations (SLIM)4 enabled unprecedented resolution in IMS separations. In addition, high sensitivity was enabled in SLIM due to lossless confinement of ions using radio frequency fields. Thus, SLIM enabled extremely long path length separations (up to 0.1 km thus far) providing efficient separation of molecular ions never before achieved (e.g. isotopologues, D&L amino acids). While SLIM has unprecedented analytical separations power/utility, the use of SLIM platform for depositing mobility and mass selected molecular ions has two specific technological challenges: (a) Pulsed nature of IMS separations and their low duty cycle and (b) the need for a low vacuum of ~4 torr for lossless ion confinement. These limitations lead to long deposition times due to loss of ions generated from the sample. Enabling ion confinement at atmospheric pressure will be path-breaking contribution to the fundamental understanding of ion manipulations and separations and will also enable novel science currently precluded due to the inability of the present technologies to confine ions under ambient conditions. Traditionally used radio frequency fields are ineffective in confining ions at high pressures due to ion/neutral collisions. To address these, we propose to (a) develop methods for confining and manipulating ions for lossless IMS separations at atmospheric pressure enabling high sensitivity and throughput and (b) use the high specificity of IMS/MS and high throughput from ambient ion confinement to perform mobility and mass selective ion deposition at atmospheric pressure. Our goal is to enable the study of the fundamental properties of energy/catalysis materials and biomolecules. This project paves the way for high-throughput, mass and structure selective material deposition for highly specific surface creation/functionalization (discussed in Section 2 of the report). Further, the developments reported continue to push the boundaries of this process to ambient conditions (discussed in Section 3 of the report). We conclude with a list of specific intellectual property and publications which have been the outcome of this funded project.
Physical aging or degradation of amine-containing polymers and supported amine adsorbents is a critical issue that could limit practical application of such materials for CO 2 capture. However, to date, there is a scarcity of studies that evaluate the long-term stability of amine-based sorbents without the exclusive use of accelerated aging tests. Here, we demonstrate that extended aging (~2 years) of linear poly(propylenimine) (LPPI) confined in mesoporous silica (SBA-15) supports does not drastically impact the CO 2 adsorption performance under simulated flue gas (10% CO 2 ) and direct air capture (DAC, 400 ppm CO 2 ) conditions, although the behavior of the aged sorbents and polymers in the two CO 2 concentration regimes differs. Sorbents made with aged LPPI had modestly decreased CO 2 uptake performance (<~20% lower) compared to the fresh polymers, with overall good CO 2 cycling performance. The data indicate that only slow degradation occurs under the deployed ambient storage conditions. Even after extended aging, the LPPI-based sorbents preserved their ability to display stable temperature-swing cycling performance. In parallel, the impact of blending LPPI polymers of different number-average molecular weights, M n , is evaluated, seeking to understand its impact on adsorbent performance. We find that the results demonstrate that blends of two M n aged LPPI give similar CO 2 adsorption performance to adsorbents made from a single M n LPPI, suggesting that molecular weight will not negatively impact adsorbent performance in the studied M n range. After an accelerated oxidation experiment, the aged LPPI sorbents retained a larger portion of the samples’ original performance when cycling under simulated flue gas conditions than under DAC conditions. However, in each case, the oxidized sorbents could be cycled repeatedly with consistent uptake performance. Overall, these first of their kind extended aging tests suggest that LPPI-based amine adsorbents offer promise for long term, stable use in carbon capture applications.
Lichens are symbiotic organisms with unique secondary metabolism. Various metabolites from lichens have shown antimicrobial activity. Nevertheless, very few studies have investigated the antimicrobial potential of the volatile compounds they produce. This study investigates the chemical composition and antimicrobial properties of volatile compounds from Pseudevernia furfuracea collected in two regions of Morocco. Hydrodistillation was used to obtain volatile compounds from samples collected in the High Atlas and Middle Atlas. Gas chromatography–mass spectrometry (GC-MS) analysis identified phenolic cyclic compounds as the primary constituents, with atraric acid and chloroatranol being the most abundant. Additionally, eight compounds were detected in lichens for the first time. The antimicrobial activity of these compounds was assessed using disc diffusion and broth microdilution methods. Both samples demonstrated significant antimicrobial effects against multidrug-resistant human bacteria, reference microorganisms, fish pathogens, and Candida albicans, with minimum inhibitory concentrations (MICs) ranging from 1000 µg/mL to 31.25 µg/mL. This study provides the first report on the volatile compounds from Pseudevernia furfuracea and their antimicrobial effects, particularly against fish pathogens, suggesting their potential as novel antimicrobial agents for human and veterinary use. Further research is warranted to explore these findings in more detail.