Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GASIFIER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Investigation of continuous carbothermal reduction of magnesia by magnesium vapor condensation onto a moving bed of solid particles

Magnesium metal production by carbothermic reduction (CTR) can reduce process emissions and energy requirements relative to silicothermic or electrolytic production, if high magnesium metal yields are achieved. A novel process was investigated where product magnesium gas condensed onto a moving bed of solid particles at high temperatures (≥300 °C) and in vacuum to minimize reversion and promote crystal growth. Using a half-system in which CTR product gases were artificially generated, magnesium continuously condensed onto steel, oxide, or carbide particles at yields >85% for P Mg = 0.5 kPa. Steel particles exhibited the greatest bed retention and ease of separation, so this medium was used for scale-up to a full-system in which MgO CTR in a fixed bed gasifier at 1400 °C–1550 °C produced Mg (g) and CO. The initial reduction resulted in high Mg yield (>80%), but yield decreased as the reaction proceeded. The accumulation of Mg (s) and reversion product in the condenser promoted further reversion. The process yield could likely be improved by using high surface area particles to promote heat and mass transfer, allowing for shorter solid and gas residence times in the condenser. A finite volume model on the reactor tube and pellet bed described the kinetics, heat transfer, and mass transfer phenomena in the reduction reactor. The model predicted that the center of the bed was >50 °C cooler than the furnace, and the product gas pressures were near equilibrium. A wide, directly heated reactor could overcome these heat and mass transfer limitations.

42 ENGINEERING↗

LCA of local strategies for energy recovery from waste in England, applied to a large municipal flow

An intense waste management (WM) planning activity is currently undergoing in England to build the infrastructure necessary to treat residual wastes, increase recycling levels and the recovery of energy from waste. From the analyses of local WM strategic and planning documents we have identified the emerging of three different energy recovery strategies: established combustion of residual waste; pre-treatment of residual waste and energy recovery from Solid Recovered Fuel in a dedicated plant, usually assumed to be a gasifier; pre-treatment of residual waste and reliance on the market to accept the 'fuel from waste' so produced. Each energy recovery strategy will result in a different solution in terms of the technology selected; moreover, on the basis of the favoured solution, the total number, scale and location of thermal treatment plants built in England will dramatically change. To support the evaluation and comparison of these three WM strategy in terms of global environmental impacts, energy recovery possibilities and performance with respect to changing 'fuel from waste' market conditions, the LCA comparison of eight alternative WM scenarios for a real case study dealing with a large flow of municipal wastes was performed with the modelling tool WRATE. The large flow of waste modelled allowed to formulate and assess realistic alternative WM scenarios and to design infrastructural systems which are likely to correspond to those submitted for approval to the local authorities. The results show that all alternative scenarios contribute to saving abiotic resources and reducing global warming potential. Particularly relevant to the current English debate, the performance of a scenario was shown to depend not from the thermal treatment technology but from a combination of parameters, among which most relevant are the efficiency of energy recovery processes (both electricity and heat) and the calorific value of residual waste and pre-treated material. The contribution and relative importance of recycling and treatment/recovery processes change with the impact category. The lack of reprocessing plants in the area of the case study has shown the relevance of transport distances for recyclate material in reducing the efficiency of a WM system. Highly relevant to the current English WM infrastructural debate, these results for the first time highlight the risk of a significant reduction in the energy that could be recovered by local WM strategies relying only on the market to dispose of the 'fuel from waste' in a non dedicated plant in the case that the SRF had to be sent to landfill for lack of treatment capacity.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The O{sub 2}-enriched air gasification of coal, plastics and wood in a fluidized bed reactor

Highlights: Black-Right-Pointing-Pointer The effect of the O{sub 2} in the gasification stream of a BFB gasifier has been studied. Black-Right-Pointing-Pointer Main advantage of the O{sub 2}-enriched air is the increasing of the bed temperature. Black-Right-Pointing-Pointer No remarkable effects on tar reduction. Decreasing of recognized PAHs. Black-Right-Pointing-Pointer Gasification reactions completed inside the dense bed and splashing zone. Black-Right-Pointing-Pointer Polycondensation reactions occur mainly in the freeboard region. - Abstract: The effect of oxygen-enriched air during fluidized bed co-gasification of a mixture of coal, plastics and wood has been investigated. The main components of the obtained syngas were measured by means of on-line analyzers and a gas chromatograph while those of the condensate phase were off-line analysed by means of a gas chromatography-mass spectrometer (GC-MS). The characterization of condensate phase as well as that of the water used as scrubbing medium completed the performed diagnostics. The experimental results were further elaborated in order to provide material and substances flow analyses inside the plant boundaries. These analyses allowed to obtain the main substance distribution between solid, gaseous and condensate phases and to estimate the conversion efficiency of carbon and hydrogen but also to easily visualise the waste streams produced by the process. The process performance was then evaluated on the basis of parameters related to the conversion efficiency of fuels into valuable products (i.e. by considering tar and particulate as process losses) as well as those related to the energy recovery.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Influence of Pelletization and Moisture Content of Oil Palm Empty Fruit Bunches (EFBs) on Dynamic Gasification Performance

Wet-ground empty fruit bunches (EFBs), dry-ground EFB, and pelletized EFB were gasified in a laboratory-scale updraft fixed-bed reactor at differing temperatures and equivalent ratios (ERs) between 0.19 and 0.78 to evaluate the performance and quality of the syngas under autothermal operating conditions. In addition, the theoretical estimation of the key performance indicator of the ashes on the performance of the gasification process was obtained. The results show that for ERs > 0.4 the autothermal operating condition was achieved for pretreatments with pelletized and dry-ground EFBs, with reactor operating temperatures T > 700 °C. With wet EFB, this condition is achieved at any ER value. The average composition of the syngas from pelletized EFB presented the best average concentrations of the combustible species CO, H2, and CH4 when the ER values were between 0.25 and 0.40. The highest hot and cold thermal efficiency values were obtained for the gasification of EFB pellets with ER values between 0.25 and 0.40. For ground EFB, increases in the ER value led to improvements in hot thermal efficiency. Finally, during the EFB pellet gasification tests, no agglomeration and sintering problems were evidenced in comparison with wet-ground and dry-ground EFBs that showed slag formation, especially at ER < 0.46.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Bed Agglomeration During the Steam Gasification of a High Lignin Corn Stover Simultaneous Saccharification and Fermentation (SSF) Digester Residue

This research investigates the bed agglomeration phenomena during the steam gasification of a high lignin residue produced from the simultaneous saccharification and fermentation (SSF) of corn stover in a bubbling fluidized bed. The studies were conducted at 895°C using alumina as bed material. Biomass was fed at 1.5 kg/hr, while steam was fed to give a velocity equal to 2.5 times the minimum fluidization velocity, with a steam/carbon ratio of 0.9. The pelletized feedstock was co-fed with a cooling nitrogen stream to mitigate feed line plugging issues. Tar production was high at 50.3 g/Nm3, and the fraction of C10+ compounds was greater than that seen in the gasification of traditional lignocellulosic feedstocks. Carbon closures over 94 % were achieved for all experiments. Bed agglomeration was found to be problematic, indicated by pressure drop increases observed below the bed and upstream of the feed line. Two size categories of solids were recovered from the reactor, +60 mesh and -60 mesh. After a 2.75-hour experiment, 61.7 wt % was recovered as -60 mesh particles and 38.2 wt% of the recovered reactor solids were +60 mesh. A sizeable percentage, 31.8 wt%, was +20 mesh. The -60 mesh particles were mainly formed by the initial bed material (Al2O3). Almost 50 wt. % of the + 20 mesh particles was found to be formed by organics. The unreacted carbon remaining in the reactor resulted in a low conversion rate to product gas. ICP-AES, SEM, SEM-EDS, and XRD confirmed that the large agglomerates (+ 20 mesh) were not encapsulated bed material but rather un-gasified feedstock pellets with sand particles attached to it.

bioenergy↗

Warm Cleanup of Coal-Derived Syngas: Multicontaminant Removal Process Demonstration

Warm cleanup of coal- or biomass-derived syngas requires sorbent and catalytic beds to protect downstream processes and catalysts from fouling. Sulfur is particularly harmful because even parts-per-million amounts are sufficient to poison downstream synthesis catalysts. Zinc oxide (ZnO) is a conventional sorbent for sulfur removal; however, its operational performance using real gasifier-derived syngas and in an integrated warm cleanup process is not well reported. In this paper, we report the optimal temperature for bulk desulfurization to be 450oC, while removal of sulfur to parts-per-billion levels requires a lower temperature of approximately 350oC. Under these conditions, we found that sulfur in the form of both hydrogen sulfide and carbonyl sulfide could be absorbed equally well using ZnO. For long-term operation, sorbent regeneration is desirable to minimize process costs. Over the course of five sulfidation and regeneration cycles, a ZnO bed lost about a third of its initial sulfur capacity, however sorbent capacity stabilized. Here, we also demonstrate, at the bench-scale, a process and materials used for warm cleanup of coal-derived syngas using five operations: 1) Na2CO3 for HCl removal, 2) regenerable ZnO beds for bulk sulfur removal, 3) a second ZnO bed for trace sulfur removal, 4) a Ni-Cu/C sorbent for multi-contaminant inorganic removal, and 5) a Ir-Ni/MgAl2O4 catalyst employed for ammonia decomposition and tar and light hydrocarbon steam reforming. Syngas cleanup was demonstrated through successful long-term performance of a poison-sensitive, Cu-based, water-gas-shift catalyst placed downstream of the cleanup process train. The tar reformer is an important and necessary operation with this particular gasification system; its inclusion was the difference between deactivating the water-gas catalyst with carbon deposition and successful 100-hour testing using 1 LPM of coal-derived syngas.

Spies, Kurt A.↗

Conversion of Coal in a Fluidized Bed Chemical Looping Combustion Reactor with and without Oxygen Uncoupling

Chemical looping combustion (CLC) is a carbon capture technology that involves circulating metal-based oxygen carrier particles between two reactors, where the metal is alternately oxidized by air and then reduced by fuel as the fuel combusts. In the variant of CLC known as chemical looping with oxygen uncoupling (CLOU), the oxygen carrier releases gaseous O 2 in the fuel reactor, allowing for a rapid reaction with solid fuels. This study focuses on improving the understanding of mechanisms responsible for carbon conversion of coal and coal char in a bench-scale fluidized bed reactor using oxygen carriers with and without oxygen uncoupling properties. Effects of coal particle size and temperature on the rate of carbon conversion are evaluated in order to quantify performance and to aid in design and modeling of large-scale fully circulating chemical looping systems. The data confirms that conversion with a copper-based CLOU carrier is faster and results in lower CO and CH 4 concentrations than the natural ore ilmenite, which does not have CLOU properties. Furthermore, with coal as fuel, the increase in the rate of char carbon conversion with CLOU is lower than that previously reported because of competition for oxygen by volatiles. Conversion is also faster with smaller particles but results in higher CO concentrations as small particles gasify and release volatiles more quickly.

01 COAL, LIGNITE, AND PEAT↗

Sustainable H 2 -Rich Syngas Production via Microwave-Assisted vs Conventional Catalysis of Pinewood

Catalytic gasification of biomass is a promising method for producing hydrogen-rich syngas, which is a valuable resource for cleanenergy applications. In this study, microwave-assisted biomass gasification was compared with conventional thermally driven biomass gasification using pinewood as the biomass without the use of external gasifying agents (such as air, steam, and CO 2 ), under non-catalytic and catalytic conditions. The catalysts consisted of either an iron or a nickel catalyst, and the pinewood used as biomass contained 42% oxygen. This comparative analysis explores the differences in reaction chemistry, product yields, and the role of key reactions such as the water gas shift (WGS) reaction, Boudouard reaction, etc. The gas-phase and liquid-phase products were analyzed using online gas chromatography, and the fresh and spent catalysts were analyzed using X-ray diffraction (XRD) techniques. It was found that microwave-assisted gasification offers advantages in terms of enhanced reaction efficiency, catalyst stability, and hydrogen yield. For the microwave-assisted reaction, the gas yield reached 87%, the char yield was 12.1%, and the tar yield was less than 1% (0.793%) at 550 °C. In contrast, thermal-assisted gasification using the same catalyst produced a gas yield of 85.796%, char yield of 11.438%, and higher tar yield of 2.8% at 900 °C. The higher microwave-assisted performance was attributed to faster heating and better control over reaction conditions, higher reaction rates, and more favorable conditions for hydrogen production.

biomass↗

Effects of Measurement Materials and Oxygen Partial Pressure on the Viscosity of synthetic Eastern and Western United States Coal Slags

The viscosity of the molten ash (slag) resulting from the mineral constituents in carbon feedstock used in slagging gasifiers is critical for controlling the gasification process. The viscosity of two synthetic slags with compositions resembling the mineral impurities in average eastern and western coal feedstock was examined at temperatures from 1300–1500 °C using a rotating bob viscometer. A few combinations of atmospheres and experimental materials were investigated with respect to one another to determine slag viscosity. A CO/CO{sub 2} atmosphere (CO/CO{sub 2} = 1.8, corresponding to a P{sub O{sub 2}} = 10–8 atm) is required to sustain ferrous ions in FeO-containing slags, an environment that is oxidizing to most metals. Iron oxide in the slag prevents usage of Fe parts. In unpurified Ar, the Fe metal surface oxidizes. Using purified argon prevents iron measurement components from oxidation; however, the metallic surfaces act as nucleation sites for the reduction of the Fe oxide in the slag into metallic Fe. Dissolution of ceramic materials into the slag, including Al{sub 2}O{sub 3} and ZrO{sub 2}, occurs in both atmospheres. Therefore, evaluating slag properties in the laboratory is challenging. The measured viscosities of two synthetic slags in this study diverged depending upon material selection. This difference is likely attributable to container/spindle-slag interactions. Viscosity measurements of the eastern coal slag using all ceramic parts agreed best with FactSage prediction above 1350 °C, with an average activation energy of 271.2 kJ. For western coal slag, the dissolution of container/spindle materials was substantial during the measurement, with precipitation of crystalline phase noted. The experimental viscosity data of the western coal slag agreed best with Kalmanovitch prediction above 1350 °C. The activation energy changed dramatically for both data sets of western coal slag, likely indicating the Newtonian-to-non-Newtonian transition.

01 COAL, LIGNITE, AND PEAT↗

Steam Gasification Rates of Three Bituminous Coal Chars in an Entrained-Flow Reactor at Pressurized Conditions

Three bituminous coal chars (Illinois #6, Utah Skyline, and Pittsburgh #8) were gasified separately at total pressures of 10 and 15 atm in an entrained-flow reactor using gas temperatures up to 1830 K and particle residence times <240 ms. The experiments were performed at conditions where the majority of particle mass release was due to H 2 O gasification, although select experiments were performed at conditions where significant mass release was due to gasification by both H 2 O and CO 2 . The measured coal data we recorded were fit to three char gasification models including a simple first-order global model, as well as the CCK N and CCK models that stem from the CBK model. The optimal kinetic parameters for each of the three models are reported, and the steam reactivity of the coal chars at the studied conditions is as follows: Pittsburgh #8 > Utah Skyline > Illinois #6.

01 COAL, LIGNITE, AND PEAT↗

Crystalline structure transformation of carbon anodes during gasification

The crystalline structure transformation of five carbon anodes during gasification in air and carbon dioxide was studied using quantitative X-ray diffraction (XRD) analysis and high-resolution transmission electron microscopy (HRTEM). XRD analysis and HRTEM observations confirmed that anodes have a highly ordered graphitic structure. The examination of partially gasified samples indicated that crystalline structure transformation occurred in two stages during gasification. The first stage involved the consumption of disorganized carbon matter in the initial 15% conversion. Oxygen was found to be more reactive toward disorganized carbon at this stage of the gasification process compared to carbon dioxide. Following this stage, as more carbon was consumed, especially with the removal of smaller crystallites, it was found that the crystalline structure became more ordered with increasing conversion levels. This is due to the merging of neighboring crystallites, required to maintain the minimum energy configuration. In addition, the interaction between the pitch and the coke components was found to be strongly linked to the initial coke structure. 'Stress graphitization' occurred at the pitch-coke interface, which helps to enhance the structural development of the anodes. 26 refs., 9 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Hydrogen production from the steam-iron process with direct reduction of iron oxide by chemical looping combustion of coal char

Experimental results performed with a fluidized-bed reactor supported the feasibility of the three processes including direct reduction of iron oxide by char, H{sub 2} production by the steam-iron process, and the oxidation of Fe{sub 3}O{sub 4} resulting from the steam-iron process to the original Fe{sub 2}O{sub 3} by air. Chars resulting from a Chinese lignite loaded with K{sub 2}CO{sub 3} were used successfully as a reducing material, leading to the reduction of Fe{sub 2}O{sub 3} to FeO and Fe for the steam-iron process, which was confirmed by both the off-gases concentrations and X-ray diffractometer analysis. The reduction of Fe{sub 2}O{sub 3} by K-10-char at 1073 K is desirable from the perspective of the carbon conversion rate and high concentration of CO{sub 2}. The carbon in char was completely converted to CO{sub 2} when the mass ratio of Fe{sub 2}O{sub 3}/K-10-char was increased to 10/0.3. The oxidation rate of K-10-char by Fe{sub 2}O{sub 3} without a gasifying agent was comparable to the K-10-char steam gasification rate. The fractions of FeO and Fe in the reduced residue were 43 and 57%, respectively, in the case of 3 g of Fe{sub 2}O{sub 3} and 0.5 g of K-10-char, which was verified by the total H{sub 2} yield equaling 1000 mL/g K-10-char from the steam-iron process. The time that it took to achieve complete oxidation of Fe{sub 3}O{sub 4} to Fe{sub 2}O{sub 3} by air with an 8.7% O{sub 2} concentration at 1073 K was about 15 min. 53 refs., 19 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Solar-driven coal gasification in a thermally irradiated packed-bed reactor

Coal gasification for high-quality synthesis gas production is considered using concentrated solar energy as the source of high-temperature process heat. The solar reactor consists of two cavities separated by a radiant emitter plate, with the upper one serving as the solar absorber and the lower one containing the reacting packed bed that shrinks as the reaction progresses. A 5 kW prototype reactor with an 8 cm depth, 14.3 cm diameter cylindrical bed was fabricated and tested in a high-flux solar furnace, subjected to solar flux concentrations up to 2600 suns and packed-bed temperatures up to 1440 K. The reactor is modeled by formulating the 1D unsteady energy conservation equation that couples conductive-radiative heat transfer with the reaction kinetics and solving it by the finite volume technique for a transient shrinking domain. The overall reaction rate was determined experimentally by thermogravimetry, while the effective thermal conductivity was determined experimentally in a radial heat flow oven. Model validation was accomplished in terms of bed temperatures, gasified mass, and bed shrink rates measured in solar experiments conducted with beech charcoal. Heat transfer through the bed proved to be the rate-controlling mechanism, indicating an ablation regime. 31 refs., 18 figs.

01 COAL, LIGNITE, AND PEAT↗

Investigating the formation mechanism of soot-like materials present in blast furnace coke samples

An attempt to gain an understanding of the formation mechanism of these 'soot-like' materials has been made by means of tracing the changes in the molecular-mass distribution and molecular structure of the NMP-extractable materials from an injectant coal as well as its partially gasified chars and its pyrolytic tars. Variations in the SEC chromatograms provide clues about changes in the apparent molecular-mass distributions of these NMP extracts. Results suggest that the build-up of 'soot-like' materials follows from the secondary reactions of tars evolved from the injectant coal. The likely secondary-reaction pathways have been probed by collating structural information on these NMP extracts. The time-resolved 13-16 and 22-25 min elution fractions from the SEC column have been characterized using UV fluorescence (UV F) spectroscopy. Greater concentrations of larger aromatic ring systems are found present in samples formed under conditions appearing more prone for soot formation. The 11-16 min (large apparent molecular mass) effluent from SEC has been examined by Fourier transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM). Results from FTIR spectroscopy are consistent with the UV F data, showing more significant extents of dehydrogenation under conditions more prone to form soot. Similarly, TEM results show that larger amount of graphene layers exist in samples exposed to more soot-prone conditions. The emerging picture for the formation of 'soot-like' materials involves a well-defined sequence. Tars evolved from the injectant coal undergo secondary dehydrogenation, condensation, and repolymerization reactions, which eventually lead to the formation of the NMP-extractable 'soot-like' materials of large apparent molecular mass. 44 refs., 7 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Preventing ash agglomeration during gasification of high-sodium lignite

Various additives were evaluated to assess their ability to prevent ash agglomeration during the gasification of high-sodium lignite. Additives that showed promise in simple muffle furnace tests included meta-kaolin, vermiculite, two types of silica fume, and one type of bauxite. Additives that were tested and rejected included dolomite, calcite, sand flour, kaolinite, fine kaolin, and calcined bauxite. Based on the muffle furnace test results, the meta-kaolin was selected for a follow-on demonstration in a pilot-scale coal gasifier. Pilot-scale testing showed that the addition of coarse (minus 14-mesh, 920-{mu}m mean size) meta-kaolin at a feed rate roughly equivalent to the ash content of the lignite (10 wt %) successfully prevented agglomeration and deposition problems during gasification of high-sodium lignite at a maximum operating temperature of 927{sup o}C (1700{sup o}F). 13 refs., 24 figs., 1 tab.

01 COAL, LIGNITE, AND PEAT↗

Mineralogical characterization of Sasol feed coals and corresponding gasification ash constituents

Feed coal and coarse ash particles (heated rock fragments and clinkers), produced from Sasol-Lurgi gasifier tests under different operating conditions, have been characterized by quantitative X-ray diffraction, electron microprobe analysis, and associated chemical techniques, as a basis for better understanding of the relations between the mineralogical and physical properties of the ash particles. Crystalline phases in the ashes include quartz particles inherited directly from the feed coal, as well as anorthite, mullite, and diopside, derived from solid-state reactions or crystallization of a silicate melt during the gasification process. Glass, cooled from the melt, is also abundant in the ash materials. The abundance of large particles of hard minerals in the coal or the ash, such as quartz, anorthite, pyrite, and diopside, has been correlated with a laboratory-determined abrasion index and may contribute significantly to wear on mechanical equipment during coal- or ash-handling operations. 21 refs., 3 figs., 9 tabs.

01 COAL, LIGNITE, AND PEAT↗

Phase shift method to estimate solids circulation rate in circulating fluidized beds

While solids circulation rate is a critical design and control parameter in circulating fluidized bed (CFB) reactor systems, there are no available techniques to measure it directly at conditions of industrial interest. Cold flow tests have been conducted at NETL in an industrial scale CFB unit where the solids flow has been the topic of research in order to develop an independent method which could be applied to CFBs operating under the erosive and corrosive high temperatures and pressures of a coal fired boiler or gasifier. The dynamic responses of the CFB loop to modest modulated aeration flows in the return leg or standpipe were imposed to establish a periodic response in the unit without causing upset in the process performance. The resulting periodic behavior could then be analyzed with a dynamic model and the average solids circulation rate could be established. This method was applied to the CFB unit operated under a wide range of operating conditions including fast fluidization, core annular flow, dilute and dense transport, and dense suspension upflow. In addition, the system was operated in both low and high total solids inventories to explore the influence of inventory limiting cases on the estimated results. The technique was able to estimate the solids circulation rate for all transport circulating fluidized beds when operating above upper transport velocity, U{sub tr2}. For CFB operating in the fast fluidized bed regime (i.e., U{sub g}< U{sub tr2}), the phase shift technique was not successful. The riser pressure drop becomes independent of the solids circulation rate and the mass flow rate out of the riser does not show modulated behavior even when the riser pressure drop does.

42 ENGINEERING↗