Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fission gas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Technical Assessment of Off-Gas System Technologies for Potential Use in Molten Salt Reactors

Molten salt reactors (MSRs) are a class of Generation IV advanced reactor technologies aimed to enhance and improve the safety, fuel utilization and cost-effectiveness of nuclear power generation. MSR concepts are based on using a molten salt mixture as a primary nuclear reactor coolant, while the fuel can be either directly dissolved in the coolant (i.e., fluid-fueled) or can be in a separate solid form (i.e., salt-cooled solid-fueled). MSRs can be operated in either thermal or fast neutron spectra, as simple fissile convertors, or breeder reactors (e.g., utilizing both fissile and fertile fuels), as well as accelerator-driven sub-critical reactors or transuranic element burners. Operation of MSRs will necessitate management and treatment of the off-gas streams released to the headspace of the reactor where, in some designs, a cover gas can be circulated to remove certain fission products and maintain an inert atmosphere. An inert MSR cover gas swept over or sparged into the salt will confine radionuclides emerging from the free surface, including radioactive noble and non-noble gases, aerosols, and volatile species. The elements and compounds of these species will have a wide range of thermochemical and physical properties, some of which will decay to different products in the off-gas stream. Therefore, system components used to manage and treat MSR off-gas streams will need to be robust under dynamic reactor and chemistry conditions to support adequate reactor performance by managing the composition and species in the salt coolant and cover gas space. Off-gas system components would perform as a radionuclide boundary to the reactor vessel and a primary means for preventing radionuclide release; therefore, they are of high safety significance for MSR operations. This report reviews various technologies and materials for potential implementation in the design of an MSR off-gas system per a general conceptual framework. The reviewed technologies operate based on scrubbing, capture, delay, or separation of species in the off-gas stream. These include molten hydroxide scrubbers, solid sorbents, delay off-gas systems, particle traps, and cryogenic distillation. Since aspects of an off-gas system will be design-specific, the approach is to provide general discussions on attributes of these technologies and materials, including target off-gas stream species, operational parameters and conditions of importance to decontamination factors, implementation maturity, system component monitoring, potential off-normal conditions and considerations for waste products. The information aims to support the U.S. Nuclear Regulatory Commission in their safety evaluations for MSR designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Atom probe tomography of segregation at grain boundaries and gas bubbles in neutron irradiated U-10 wt% Mo fuel

During neutron irradiation to fission densities > 5.2 × 10 21 fiss/cm 3 , Xe agglomerates forming gas bubbles of varying size within the U-Mo fuel matrix. Herein, segregation of fission products to Xe bubbles and grain boundaries (GB) were studied using atom probe tomography (APT). Segregation behavior was found to vary among GBs, small bubbles (<10 nm), and larger bubbles (>10 nm). Solid fission products were enriched at GBs and larger bubbles, but not at small bubbles. Finally, a denuded zone was identified adjacent to a > 10 nm Xe gas bubble and a GB.

36 MATERIALS SCIENCE↗
NASA NTRS1976

The excess fission xenon problem in lunar samples

This paper presents noble-gas (neon, krypton, and xenon) data obtained in stepwise heating of five lunar breccias: 14063, 14082, 15205, 15405, and 15445. These data are discussed in terms of spallation gas content, cosmic-ray exposure ages, and content of fission xenon. None of these samples is rich in solar-wind gases, and none contains more fission xenon than would be expected for in situ fission of U-238 and Pu-244. The essential features of the excess-fission-xenon phenomenon seen in several Apollo 14 samples are reviewed, as are models which might account for this phenomenon and criteria by which these models may be evaluated. The lack of excess fission xenon in 14063 and 14082 eliminates models relying on microscale xenon redistribution. A model is proposed in which the excess fission xenon originates in local material and percolates through and is adsorbed on regolith material.

Drozd, R. J.↗
NASA NTRS1979

Potentials of fissioning plasmas

Successful experiments with the nuclear pumping of lasers have demonstrated that in a gaseous medium the kinetic energy of fission fragments can be converted directly into nonequilibrium optical radiation. This confirms the concept that the fissioning medium in a gas-phase nuclear reactor shows an internal structure such as a plasma in near thermal equilibrium varying up to a state of extreme nonequilibrium. During 20 years of research under NASA support major elements of the fissioning plasma reactor were demonstrated in theory and experiment, culminating in a proof-of-principle reactor test conducted at the Los Alamos Scientific Laboratory. It is concluded that the construction of a gaseous fuel reactor power plant is within the reach of present technology.

Thom, K.↗
NASA NTRS1973

Cavity temperature and flow characteristics in a gas-core test reactor

A test reactor concept for conducting basic studies on a fissioning uranium plasma and for testing various gas-core reactor concepts is analyzed. The test reactor consists of a conventional fuel-element region surrounding a 61-cm-(2-ft-) diameter cavity region which contains the plasma experiment. The fuel elements provide the neutron flux for the cavity region. The design operating conditions include 60-MW reactor power, 2.7-MW cavity power, 200-atm cavity pressure, and an average uranium plasma temperature of 15,000 K. The analytical results are given for cavity radiant heat transfer, hydrogen transpiration cooling, and uranium wire or powder injection.

Putre, H. A.↗
DOE OSTI2023

Bayesian uncertainty quantification of tristructural isotropic particle fuel silver release: Decomposing model inadequacy plus experimental noise and parametric uncertainties

Tristructural isotropic (TRISO) particle fuel is one of the most promising fuel concepts enabling high temperature and high burnup reactor operation. One dominant source of radioactivity released from the TRISO particles is silver (Ag), which is subject to a high release fraction and long decay life compared to other fission products. Previous modeling efforts using the fuel performance code BISON indicated nonnegligible uncertainties in modeling the diffusion process of fission products in TRISO compared to the Advanced Gas Reactor experiments. The overall uncertainties observed when modeling the fission product diffusion can result from uncertainties in model parameters, noisy experimental measurements, and deficiencies in the developed models. The three types of underlying uncertainties have not yet been properly quantified in open literature. Here, this paper presents the Bayesian uncertainty quantification (UQ) using massively parallelizable Markov chain Monte Carlo samplers. The uncertainties due to model parameters, model inadequacy, and experimental measurement noise are quantified, with the σ term used to represent the sum of the model inadequacy and measurement noise uncertainties. It is worth noting that this is the first time the σ term is inferred for nuclear fuel experiments, as compared to using prescribed values for uncertainty quantification in previous work. The parallelizable Markov chain Monte Carlo samplers efficiently infer the model parameters and the σ term, giving insight into physical parameters like diffusion coefficients and the combined model discrepancy and measurement noise. A subsequent forward uncertainty quantification (UQ) is also performed based on the calibration results to generate more accurate predictions of the Ag release. The model inadequacy plus experimental noise is the most dominant source of uncertainty compared to the parametric uncertainty. All the UQ analyses presented in this work are based on the second series of the irradiation experiments in the Advanced Gas Reactor program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1972

To Mars in 30 days by gas-core nuclear rocket.

An important component for a concept involving a 60-day Mars mission is the gas-core nuclear-rocket engine. A gas-core reactor, however, has also other potential applications including MHD power generators, breeder reactors, and nuclear-powered lasers. The gas-core engine uses a fissioning uranium plasma to heat hydrogen and then expands it through a nozzle to convert the thermal energy into thrust. To obtain a higher specific impulse than the 825 sec of the solid-core nuclear-rocket engine, a gas core has to produce hotter hydrogen.

Ragsdale, R. G.↗
DOE OSTI2023

Plutonium Signatures in Molten-Salt Reactor Off-Gas Tank and Safeguards Considerations

Fluid-fueled molten-salt reactors (MSRs) are actively being developed by several companies, with plans to deploy them internationally. The current IAEA inspection tools are largely incompatible with the unique design features of liquid fuel MSRs (e.g., the complex fuel chemistry, circulating fuel inventory, bulk accountancy, and high radiation environment). For these reasons, safeguards for MSRs are seen as challenging and require the development of new techniques. This paper proposes one such technique through the observation of the reactor’s off-gas. Any reactor design using low-enriched uranium will build up plutonium as the fuel undergoes burnup. Plutonium has different fission product yields than uranium. Therefore, a shift in fission product production is expected with fuel evolution. The passive removal of certain gaseous fission products to the off-gas tank of an MSR provides a valuable opportunity for analysis without significant modifications to the design of the system. Uniquely, due to the gaseous nature of the isotopes, beta particle emissions are available for observation. The ratios of these fission product isotopes can, thus, be traced back to the relative amount and types of fissile isotopes in the core. This proposed technique represents an effective safeguards tool for bulk accountancy which, while avoiding being onerous, could be used in concert with other techniques to meet the IAEA’s timeliness goals for the detection of a diversion.

Dunkle, Nicholas (ORCID:000000027323011X)↗
NASA NTRS1972

Rare gas studies in Luna 16-G-7 fines by stepwise heating technique - A low fission solar wind Xe.

Examination of He, Ne, Kr, and Xe in a dust sample (equal to or less than 125 micrometer) of Luna 16 in 12 temperature steps with especially small intervals in the low temperature range (80 C steps). The gas concentrations, as well as their relative abundances, are in general agreement with values reported by Vinogradov (1971) for Luna 16 and values found in Apollo 11 fines except for Ne. Comparison is made with various other experimental results. The solar wind Xe was lower in the fission-affected isotopes than was found in Apollo 11 fines and in the 1000 C fraction of the Pesyanoe meteorite as measured by Marti (1969). Air-Xe is interpreted as a fractional solar wind Xe with the composition found in this study.

Kaiser, W. A.↗
DOE OSTI2023

Monte Carlo Analysis of Coolant Stream Impurity Gamma Emissions in Gas-Cooled Fast Reactors

It is well established that a rapid increase in the concentration of fission products in the reactor coolant stream can serve as an early indication of fuel failure. We use Monte Carlo simulations to investigate the feasibility of using several gamma detectors as diagnostic equipment to monitor the presence of major fission product isotopes in high-temperature gas-cooled reactor (HTGR) coolant streams for early detection of fuel failure and therefore the prevention of fuel failure conditions. Herein we model the response of high-purity germanium (HPGe), CdZnTe, NaI(Tl), and LaBr 3 (Ce) detectors of typical commercial sizes to the gamma emissions from nuclides expected to be found within the coolant stream of the Versatile Test Reactor (VTR) under development by the U.S. Department of Energy. The results indicate that for the 233- and 250-keV gamma rays from 133 Xe and 135 Xe, respectively, the 3σ detection criterion is met in under 1 min using a single HPGe detector. Changes in other spectral lines associated with Xe nuclides are detected within 1 h regardless of the choice of detector.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

A preconceptual design of an inverted Stable-Salt Reactor

This paper presents a preconceptual design of an inverted stable-salt reactor (SSR), with the unique feature that the static fuel salt is accommodated in one single bulk fuel container, while the coolant salt is circulating through the core via flow tubes penetrating the fuel container.The inverted SSR is expected to substantially decrease the capital cost compared to the state-of-the-art SSR such as the SSR-W designed by Moltex Energy, because one single gas vent at the top of the fuel container is required in the inverted SSR to prevent the leakage of the radioactive fission product gases instead of one gas vent in each of the hundreds of thousands of fuel tubes in SSR-W. In addition, the operation of the inverted SSR is largely simplified. However, numerous challenges associated with the design of the inverted SSR still remain to be overcome. Preliminary neutronics and thermal-hydraulics performance characteristics of the inverted SSR are assessed in this study. A viable core configuration of the inverted SSR is identified, and the superior characteristics of the inverted SSR, including a better neutron economy and a lower maximum fuel temperature, are demonstrated in this paper. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1982

Fission track studies of xenolithic chondrites - Implications regarding brecciation and metamorphism

Fission tracks in phosphates from one gas-poor chondrite and three gas-rich ones are studied to determine their thermal history and brecciation time scales. Model fission track ages are calculated for given track densities due to Pu-244 and U-238; track densities and uranium measurements for whitlockite are shown, and possible sources of the tracks are mentioned. Details of track density and uranium measurements are discussed for each meteorite separately. Whitlockites from all the meteorites give model fission track ages of 4.4 Gyr assuming a Pu/U ratio at 4.55 Gyr of 0.045. The final brecciation event definitely did not reset the track clock in phosphates of one meteor and probably not in another two. It is concluded that the observed fission track ages date the end of metamorphic cooling in the meteorite parent bodies and support the planetesimal model for the formation of xenolithic chondrites.

Kothari, B. K.↗
DOE OSTI2022

Numerical study of multi-component flow and mixing in a scaled fission product venting system

Numerical simulation of isothermal multi-component gas flow was conducted to study fluid flow and mixing in a scaled low-pressure, low-temperature test facility for the fission product venting system (FPVS) of a gas cooled fast reactor (GFR). The geometry of FPVS test facility was an open loop including gradual expansion coupling and two 90°pipe elbows. First, the validation of large eddy simulation (LES) wall-adapting local eddy-viscosity (WALE) turbulent model was performed for transitional flow in a circular pipe with gradual expansion. The reactingFOAM solver in OpenFOAM v8 was employed. By introducing appropriate turbulence disturbance at the flow inlet, such as turbulence intensity, the numerical results showed good agreement in (1) the velocity profile downstream of the pipe expansion measured by particle image velocimetry (PIV) in this study, and (2) the reattachment length reported in the literature. Using this validated model, the numerical simulation of flow and component mixing was performed for the FPVS with an inlet flowrate corresponding to a Reynolds number of 2,400 to investigate the flow behavior and component mixing. Standard deviation of the mass fraction of component, referred to as absolute mixing index (AMI), was calculated to quantify the mixing of components, showing that the component mixing length determined by AMI is related to the reattachment length downstream of the expansion. Additionally, this study was able to identify the best location in the FPVS test facility to measure the velocity and concentration profies where multicomponent flow is well mixed.

15 GEOTHERMAL ENERGY↗
NASA NTRS1981

Multiple-path fission-foil nuclear lasing of Ar-Xe

Nuclear lasing of Ar 10% Xe at 760 torr with a thermal neutron flux of 3.5 x 10 to the 16th n/sq cm s has produced an output power of 50 W. Lasing occurred at 2.6 microns in Xe-I. The argon buffer gas is shown to efficiently stop fission fragments at reasonable pressures emitted from (U-235)3O8 coatings. A unique folded optical path was used to increase the excited gas volume which in turn increases laser output.

De Young, R. J.↗
DOE OSTI2026

Triso Analysis Tool For Predictive Source Terms

Source term modeling for TRi-structural ISOtropic (TRISO) fuel has been performed for previous reactor designs, but few are available in the open literature. Thus, there is a need to develop a simple, versatile, and mechanistic model of fission product release and transport in gas reactor cores that can be applied to a variety of reactors through user inputs and reactor-specific radionuclide inventories. To meet this need, the TRISO Analysis Tool for Predictive Source terms (TRISO-ATOPS) was developed. This model calculates the release of the key safety-important fission products by diffusion through the kernel, silicon carbide and graphite based on fuel and graphite temperatures in the reactor under normal operation. These releases from the fuel enter the coolant where they can plate-out on cooler surfaces. A clean-up model is included for designs with a coolant purification system for removing fission gases. This initial distribution of fission products in the reactor serves as an initial condition for potential releases under postulated accident conditions. From this initial condition, the model calculates the fission product release for any transient temperature profile, and the fission product releases can then be used to assess radiological dose to the workers and the public using conventional radiological dose tools. Data on the diffusion of fission products is based on historic German TRISO experiments and the more current Department of Energy Advanced Gas Reactor TRISO fuel development program. The example cases in this work demonstrate the flexibility of the model

Stoyer, Benjamin [Idaho National Laboratory (INL),↗
DOE OSTI2023

The effect of interfacial phenomena on gas solubility measurements in molten salts

The behavior of fission gases in molten fuel salt reactors governs activity transport from the reactor and can also affect the performance of the reactor itself. The gas solubility can be described thermodynamically by Henry’s law. However, the coupling of the condensed and gas phases depends on the interfacial area, which is difficult to measure or even to estimate. Surfaces of materials in the reactor will include disperse phases in the salt and porosity within the structural materials, covering a range of compositions and sizes. These attributes can affect measurements of fundamental properties such as gas solubility. Methods to obtain gas solubility, surface tension, interfacial energies, and bubble gas transport are reviewed. Recent data from manometric experiments are interpreted based on xenon sorption onto salt-wetted quartz.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1982

Adsorption and excess fission Xe - Adsorption of Xe on vacuum crushed minerals

It is hypothesized that adsorption is not likely to provide a sufficiently precise mechanism for the concentration of excess fission Xe in the entire lunar regolith, in view of laboratory analogs of the lunar soil and calculations of the residence times of noble gases in the present day regolith. Lunar cold trap and episodic degassing models are difficult to reconcile, however, with the generality of excess fission Xe in all gas-rich highland breccias. It is concluded that the high Xe concentration in such highland breccias is not the result of Xe adsorption prior to the trapping of this component.

Bernatowicz, T. J.↗
NASA NTRS1991

Fission fragment assisted reactor concept for space propulsion: Foil reactor

The concept is to fabricate a reactor using thin films or foils of uranium, uranium oxide and then to coat them on substrates. These coatings would be made so thin as to allow the escaping fission fragments to directly heat a hydrogen propellant. The idea was studied of direct gas heating and direct gas pumping in a nuclear pumped laser program. Fission fragments were used to pump lasers. In this concept two substrates are placed opposite each other. The internal faces are coated with thin foil of uranium oxide. A few of the advantages of this technology are listed. In general, however, it is felt that if one look at all solid core nuclear thermal rockets or nuclear thermal propulsion methods, one is going to find that they all pretty much look the same. It is felt that this reactor has higher potential reliability. It has low structural operating temperatures, very short burn times, with graceful failure modes, and it has reduced potential for energetic accidents. Going to a design like this would take the NTP community part way to some of the very advanced engine designs, such as the gas core reactor, but with reduced risk because of the much lower temperatures.

Wright, Steven A.↗