SEARCH · Engineering Papers

Results for “FeO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

385 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Interaction between a shock wave and a turbulent boundary layer in transonic flow

Interaction between a shock wave and an unseparated turbulent boundary layer is considered. The method of matched asymptotic expansions is used, with solutions valid in the double limit as Reynolds number tends to infinity and Mach number tends to unity. The shock is weak enough that interaction effects can be considered as perturbations to the undisturbed flow; the case considered is that where the sonic line is near the outer edge of the boundary layer. It is shown that, with order estimates for Reynolds stress perturbations, the induced wall pressure distribution can be calculated using only the two outer interaction regions, independent of a specific closure condition and that this solution is in fact a turbulent free interaction solution. A detailed analysis of the inner regions, for which an eddy viscosity model for the Reynolds shear stress is used, provides a description of the variations in velocity, temperature and density near and at the wall.

Adamson, T. C., Jr.↗

NASA NTRS1982

A digital flight control system verification laboratory

A NASA/FAA program has been established for the verification and validation of digital flight control systems (DFCS), with the primary objective being the development and analysis of automated verification tools. In order to enhance the capabilities, effectiveness, and ease of using the test environment, software verification tools can be applied. Tool design includes a static analyzer, an assertion generator, a symbolic executor, a dynamic analysis instrument, and an automated documentation generator. Static and dynamic tools are integrated with error detection capabilities, resulting in a facility which analyzes a representative testbed of DFCS software. Future investigations will ensue particularly in the areas of increase in the number of software test tools, and a cost effectiveness assessment.

De Feo, P.↗

NASA NTRS1986

Requirement analysis of an intelligent, redundant, actuation system

The reliability and fault tolerance requirements of integrated, critical, digital fly-by-wire control systems for advanced military and civil aircraft requires redundant, reconfigurable implementations of the actuation system. An effective way for controlling the actuators and implementing the required fault detection and reconfiguration strategies is by means of dedicated microprocessors. This paper describes a laboratory implementation of a flexible intelligent redundant actuation system capable of demonstrating the concept and analyzing a variety of configurations and technical issues.

De Feo, P.↗

NASA NTRS1989

Feasibility of predicting performance degradation of airfoils in heavy rain

The heavy rain aerodynamic performance penalty program is detailed. This effort supported the design of a fullscale test program as well as examined the feasibility of estimating the degradation of performance of airfoils from first principles. The analytic efforts were supplemented by a droplet splashback test program in an attempt to observe the physics of impact and generation of ejecta. These tests demonstrated that the interaction of rain with an airfoil is a highly complex phenomenon and this interaction is not likely to be analyzed analytically with existing tools.

Bilanin, A. J.↗

NASA NTRS2003

Ice-Accretion Scaling Using Water-Film Thickness Parameters

Studies were performed at INTA in Spain to determine water-film thickness on a stagnation-point probe inserted in a simulated cloud. The measurements were correlated with non-dimensional parameters describing the flow and the cloud conditions. Icing scaling tests in the NASA Glenn Icing Research Tunnel were then conducted using the Ruff scaling method with the scale velocity found by matching scale and reference values of either the INTA non-dimensional water-film thickness or a Weber number based on that film thickness. For comparison, tests were also performed using the constant drop-size Weber number and the average-velocity methods. The reference and scale models were both aluminum, 61-cm-span, NACA 0012 airfoil sections at 0 deg. AOA. The reference had a 53-cm-chord and the scale, 27 cm (1/2 size). Both models were mounted vertically in the center of the IRT test section. Tests covered a freezing fraction range of 0.28 to 1.0. Rime ice (n = 1.0) tests showed the consistency of the IRT calibration over a range of velocities. At a freezing fraction of 0.76, there was no significant difference in the scale ice shapes produced by the different methods. For freezing fractions of 0.40, 0.52 and 0.61, somewhat better agreement with the reference horn angles was typically achieved with the average-velocity and constant-film thickness methods than when either of the two Weber numbers was matched to the reference value. At a freezing fraction of 0.28, the four methods were judged equal in providing simulations of the reference shape.

Anderson, David N.↗

NASA NTRS2011

Experimental Observations on the Deformation and Breakup of Water Droplets Near the Leading Edge of an Airfoil

This work presents the results of an experimental study on droplet deformation and breakup near the leading edge of an airfoil. The experiment was conducted in the rotating rig test cell at the Instituto Nacional de Tecnica Aeroespacial (INTA) in Madrid, Spain. An airfoil model placed at the end of the rotating arm was moved at speeds of 50 to 90 m/sec. A monosize droplet generator was employed to produce droplets that were allowed to fall from above, perpendicular to the path of the airfoil at a given location. High speed imaging was employed to observe the interaction between the droplets and the airfoil. The high speed imaging allowed observation of droplet deformation and breakup as the droplet approached the airfoil near the stagnation line. A tracking software program was used to measure from the high speed movies the horizontal and vertical displacement of the droplet against time. The velocity, acceleration, Weber number, Bond number, Reynolds number, and the drag coefficients were calculated along the path of a given droplet from beginning of deformation to breakup and/or hitting the airfoil. Results are presented for droplets with a diameter of 490 micrometers at airfoil speeds of 50, 60, 70, 80 and 90 m/sec

Vargas, Mario↗

NASA NTRS2012

Rotating Rig Development for Droplet Deformation/Breakup and Impact Induced by Aerodynamic Surfaces

This work presents the development of a Rotating Rig Facility by the Instituto Nacional de Tecnica Aeroespacial (INTA) in cooperation with the NASA Glenn Research Center. The facility is located at the INTA installations near Madrid, Spain. It has been designed to study the deformation, breakup and impact of large droplets induced by aerodynamic bodies. The importance of these physical phenomena is related to the effects of Supercooled Large Droplets in icing clouds on the impinging efficiency of the droplets on the body, that may change should these phenomena not be taken into account. The important variables and the similarity parameters that enter in this problem are presented. The facility's components are described and some possible set-ups are explained. Application examples from past experiments are presented in order to indicate the capabilities of the new facility.

Feo, A.↗