Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Extrusion Process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2011

The elevated-temperature mechanical behavior of as-cast and wrought Ti-6Al-4V-1B

This work studied the effect of processing on the elevated-temperature [728 K (455 C)] fatigue deformation behavior of Ti-6Al-4V-1B for maximum applied stresses between 300 to 700 MPa (R = 0.1, 5 Hz). The alloy was evaluated in the as-cast form as well as in three wrought forms: cast-and-extruded, powder metallurgy (PM) rolled, and PM extruded. Processing caused significant differences in the microstructure, which in turn impacted the fatigue properties. The PM-extruded material exhibited a fine equiaxed {alpha} + {beta} microstructure and the greatest fatigue resistance among all the studied materials. The {beta}-phase field extrusion followed by cooling resulted in a strong {alpha}-phase texture in which the basal plane was predominately oriented perpendicular to the extrusion axis. The TiB whiskers were also aligned in the extrusion direction. The {alpha}-phase texture in the extrusions resulted in tensile-strength anisotropy. The tensile strength in the transverse orientation was lower than that in the longitudinal orientation, but the strength in the transverse orientation remained greater than that for the as-cast Ti-6Al-4V. The ratcheting behavior during fatigue is also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Microstructure and Strengthening Mechanisms in an Ultrafine Grained Al-Mg-Sc Alloy Produced by Powder Metallurgy

Additions of Sc to an Al-Mg matrix were investigated, paying particular attention to the influence of Al3Sc precipitates and other dispersoids, as well as grain size, on mechanical behavior. Prior studies have shown that Sc significantly increases the strength of coarse-grained Al-Mg alloys. Prompted by these findings, we hypothesized that it would be of fundamental and technological interest to study the behavior of Sc additions to an ultrafine-grained (UFG) microstructure (e.g., 100’s nm). Accordingly, we investigated the microstructural evolution and mechanical behavior of a cryomilled ultrafine grained Al-5Mg-0.4Sc (wt pct) and compared the results to those of an equivalent fine-grained material (FG) produced by powder metallurgy. Experimental materials were consolidated by hot isostatic pressing (HIP’ing) followed by extrusion or dual mode dynamic forging. Under identical processing conditions, UFG materials generate large Al3Sc precipitates with an average diameter of 154 nm and spaced approximately 1 to 3 µm apart, while precipitates in the FG materials have a diameter of 24 nm and are spaced 50 to 200 nm apart. The strengthening mechanisms are calculated for all materials and it is determined that the greatest strengthening contributions for the UFG and FG materials are Mg-O/N dispersion strengthening and precipitate strengthening, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermomechanical Processing of Uranium Alloys with 10 and 50 Weight Percent Zirconium

This work focuses on casting and thermomechanical processing for moderate sized (500-1000g) 10% by weight and 50% by weight uranium-zirconium alloys. Three castings of uranium – 10wt% zirconium and a fourth casting of uranium – 50wt% zirconium were completed using different castings processes. The first casting process relied on only induction mixing within the VIM system thereby eliminating the need for an arc-melting feedstock preparation step. The second casting process used the arc-melting process prior for feedstock to the same VIM system. In this study, the induction mixing process alone with a graphite crucible appears insufficient for the fabrication of UZr alloys. Graphite is suitable with the use of master alloy UZr feedstock produced by arc-melting. There was a moderate increase of approximately 100 ppm of carbon within the U10Zr alloys. However, there was a near 1000 ppm increase of carbon in the U50Zr alloy. This carbon content is considered too high for forming processes, and therefore, warrants the use of a ceramic crucible for UZr castings near 50wt% zirconium. Zirconia does not appear suitable for UZr castings near 50wt% zirconium. The use of Beryllia or Thoria may be a more suitable option. However, due to the significantly lower liquidus and lower zirconium content, Zirconia crucibles do appear viable for carbon reduction in the U10Zr system. Two thermomechanical processes are also studied in this work - hot extrusion of the U50Zr system and heat treatment in an argon atmosphere. This work demonstrated that extrusion of the U50Zr alloy near 680°C is a viable choice even with +1000 ppm carbon. Extrusion of the U50Zr system near 630°C was unsuccessful and does not appear viable unless significant force and tooling strength is available. There appears to be a moderate increase in extrudate hardness when compared to as-cast. Heat-treatment reduced the hardness of as-cast alloys in the U10Zr castings as well as resolve some variance in the microstructures. However, for the U50Zr billet that did not successfully extrude at 630°C, heat treatment at 900°C for 96 hours did not have a significant impact on hardness or microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Thick Co-Extruded Cathode Electrodes for High Energy Lithium-Ion Batteries

Co-Extrusion (CoEx) is a high speed, scalable deposition process for creating finely patterned, interdigitated thick films. Our CoEx printhead is designed to be a drop-in replacement for slot-die heads on web coaters, enabling novel geometric structuring of electrodes with minor changes to existing battery electrode processing lines. Here, we present the use of CoEx to prepare thick (~ 120 µm) NMC cathode electrodes consisting of alternating regions of high lithium-ion transport and high lithium-ion storage capacity. By structuring the cathode electrode, we enable full lithium utilization at C/2, despite near doubling of the electrode thickness compared to conventional baseline electrodes. CoEx cathode electrodes are paired with thick, graded graphite anode electrodes and assembled into 1 Ah pouch cells for electrochemical testing. CoEx pouch cells demonstrate 10 – 20% improved energy density with respect to conventional electrodes and > 30% improved power density with respect to thick conventional (unstructured) electrodes at high discharge rates,

25 ENERGY STORAGE↗
DOE OSTI2016

Processing of Nanostructured Ferritic Alloys for Advanced Reactor Core Materials

The Fuel Cycle Research and Development Program is investigating methods of burning minor actinides in a transmutation fuel. To achieve this goal, the fast reactor core materials (cladding and duct) must be able to withstand very high doses (>200 dpa design goal) while in contact with the coolant and the fuel. Thus, these materials must withstand radiation effects that promote low temperature embrittlement, high temperature helium embrittlement, swelling, accelerated creep, corrosion with the coolant, and chemical interaction with the fuel (FCCI). One of the most promising materials for this demanding applications are the class of nanostructured ferritic alloys. These materials are ferritic alloys with high chrome (9-14Cr) with a high density (>10{sup 23}/m{sup 3}), fine distribution of nanosized (∼2 nm) oxide particles and a fine grain size (<0.5 micron). This fine microstructure provides an alloy with high strength at high temperatures and excellent radiation tolerance (e.g. reduced void swelling and ductility retention at low temperatures) but also increases the difficulty of producing engineering parts (e.g. thin walled tubes) from these advanced materials. Thus, extensive research is underway to produce tubes using techniques such as high temperature hydrostatic extrusion, intermediate temperature plug drawing and low temperature pilger processing. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2011

FCRD Milestone Report: M21AF050901

The objective of this study was to perform mechanical testing on large scale heats of the advanced ODS 14YWT alloy to investigate the effects of processing parameters on mechanical properties. Mechanical properties tests were conducted on two heats of the advanced ODS 14YWT ferritic alloy: the 14YWT-SM11 was produced by extrusion at ORNL and OW4 was produced by HIP at UCSB. The 14YWT-SM11 showed very high tensile strength compared to OW4, but showed less ductility as a result. The fracture toughness transition temperature of 14YWT-SM11 was determined in two orientations and showed T{sub 0} = 48 C in the favorably strong L-T direction while shifting by 63 C to T{sub 0} = 111 C in the weaker T-L direction. The fracture toughness transition temperature for OW4 was not determined but appeared to be within the range observed for 14YWT-SM11. The fracture toughness of 14YWT-SM11 at room temperature was 86.8 MPa{radical}m and 93.1 MPa{radical}m, which was much higher than that of OW4 (27.4 MPa{radical}m). The strain rate jump tests conducted on OW4 indicated that the creep properties were similar to MA957 at 750 C.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Development of Biocomposite Superabsorbent Nanomaterials: Effect of Processing Technique

Nanoclay particles have been usually introduced into protein-based bioplastics to obtain composite materials, showing enhanced mechanical properties. However, the addition of partially exfoliated nanoclay particles in these protein matrices may also involve an increase of others properties such as water absorption capacity, which may lead to the obtention of super absorbent biodegradable materials. Processing technologies exerted a remarkable influence on the techno-functional properties of the soy-based bioplastics studied in this research. On the one hand, extrusion technique led to bioplastics which showed enhanced mechanical properties. On the other hand, injection moulding technique yielded to non-exfoliated nanoclay particles within the protein matrix, which involved improvements of water absorption capacity. The development of superabsorbent protein-based biodegradable materials implied a deep knowledge of physicochemical properties of proteins and processing conditions of bioplastics. Extrusion or injection moulding techniques could be selected to obtain tailored protein-based bioplastics with enhanced properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Hydrothermally carbonized biomass formed via reactive twin-screw extrusion

A biomass-derived thermosetting polymer material being a product of processing a biomass feed material via a twin screw extruder having a length extending between an inlet and an outlet. Hot water from a water heater is injected into at least one inlet along the length of the twin screw extruder, the at least one inlet generally corresponding with a pressure boundary within the twin screw extruder. A pressure-sustaining valve is connected between the length of the twin screw extruder and the outlet, with the valve being adjusted to produce the biomass-derived thermosetting polymer material.

09 BIOMASS FUELS↗
DOE OSTI2020

Single-Step Shear-Based Deformation Processing of Electrical Conductor Wires

Commercial electrical conductor wires are currently produced from aluminum alloys by multi-step deformation processing involving rolling and drawing. These processes typically require 10 to 20 steps of deformation, since the plastic strain or reduction that can be imposed in a single step is limited by material workability and process mechanics. Here, we demonstrate a fundamentally different, single-step approach to produce flat wire aluminum products using machining-based deformation that also ensures adequate material workability in the formed product. Two process routes are proposed: (1) chip formation by free-machining (FM), with a post-machining, light drawing reduction (<20%) to achieve desired finish and (2) constrained chip formation by large strain extrusion machining (LSEM). Using commercially pure aluminum conductor alloys (Al 1100 and EC1350) as representative material systems, we demonstrate key features of the machining-based processing, including (a) single-step processing to achieve flat wire geometries, (b) surface finish (Ra = 0.2 to 1.0 μm) comparable to that of commercial wire products made by drawing/rolling, (c) deformation control independent of wire size, and (d) hardness increases of 50–150% over that of annealed wires, while retaining high electrical conductivity (>56% IACS). Here, the wire microstructure, which can also be varied via the large-strain deformation parameters, is correlated with mechanical and electrical properties. Implications for commercial manufacture of flat wire products are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Vacuum-assisted extrusion to reduce internal porosity in large-format additive manufacturing

Large-scale 3D printing of polymer composite structures has gained popularity and seen extensive use over the last decade. Much of the research related to improving the mechanical properties of 3D-printed parts has focused on exploring new materials and optimizing print parameters to improve geometric control and minimize voids between printed beads. However, porosity at the microstructural level (within the printed bead) has been much less studied although it is almost universally observed at levels of 4 %-10 % when using fiber reinforced materials. This study introduces a vacuum-assist approach that minimizes internal porosity by removing ambient air from the interstitial space between pellets in the hopper and acts as a negative pressure vent for gases that evolve during the initial stages of single-screw extrusion. Vacuum-assisted extrusion was able to reduce porosity below 2 % across a wide range of processing parameters, moisture content, fiber reinforcements, and printing platforms. Specifically, when printing on a large-format extruder (Strangpresse Model-30), the vacuum-assisted extrusion reduced internal porosity by 35–75 % compared to conventional non-vacuum extrusion, and only pores with length scale > 2 microns are affected. The success of this approach prompted the design of a patent-pending continuous vacuum hopper relevant for large-scale 3D printing on commercial systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Decoupling the effects of texture and composition on magnetic properties of Fe-Si sheet processed by shear deformation

Soft magnetic Fe-Si alloys (electrical steels) possess exceptional functional properties such as high permeability, low coercivity, and low core loss, which generally improve with increasing Si content in the alloy. However, Fe-Si alloys containing > 3.5 wt% Si are also characterized by prohibitively low workability and poor ductility that have prevented their efficient commercial production in sheet form by rolling. This has limited their use for improving efficiency of motors and transformers. In this study, hybrid cutting-extrusion (HCE) is used as a single-step thermomechanical processing method to produce continuous Fe-Si alloy sheet with high Si compositions of 4 wt% to 6.5 wt%. HCE sheet is shown to have a homogeneous annealed grain structure and simple-shear crystallographic textures. By controlling the HCE deformation path, varied crystallographic shear textures are created in the sheet. Quasi-static magnetic properties of the HCE sheet are evaluated to decouple the effects of sheet texture and Si composition on resultant permeability and coercivity properties. The results suggest that HCE, with suitable process scaling, is a viable route for production of high-Si content electrical steel sheet for next-generation motors and transformers.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Big Area Additive Manufacturing (BAAM) Materials Development and Reinforcement with Advanced Composites

Additive manufacturing (AM) by extrusion deposition is rapidly developing as an energy efficient process that greatly reduces development time for new products including vehicle structures. Development of reinforced thermoplastic compounds that are specifically tailored to the AM process and possess the properties necessary for engineering structures is currently underway. This project focused on developing a fundamental understanding of printability by performing a number of polymer characterization tests, initial printability screenings, and basic mechanical property determinations for a number of compounds. Structural evaluations of more complex printed articles were also performed in order to build a database of mechanical performance for validation of structural simulations planned for Phase II. Included in the structural tests were components that were reinforced using a number of methods including over-wrapping with dry fabric and resin infusing to form an advanced composite having the shape of the 3D printed structure. The results indicate a number of factors that affect printability of materials, and initial structural analysis shows that the data generated will be useful for model validation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Post-process annealing of large-scale 3D printed polyphenylene sulfide composites

Large-scale extrusion-based additive manufacturing of high-performance thermoplastic composites like fiber reinforced polyphenylene sulfide (PPS) is well-suited for tooling applications to lower manufacturing costs and lead times. Autoclave tooling requires good mechanical performance at temperatures even above the glass transition temperature (T g ). In this work, the authors have investigated a post-process isothermal annealing technique to improve the mechanical properties of various grades of carbon fiber reinforced PPS components printed on the Big Area Additive Manufacturing (BAAM) system. Since PPS is a semi-crystalline polymer, crystallinity can change during annealing and affect the mechanical properties of the part. In addition, isothermal annealing can also lead to solid-state structural changes in the form of thermal and oxidative branching and/or crosslinking reactions in some grades of PPS which can alter the crystallization process. This work reports the effect of annealing on dynamic mechanical properties of BAAM printed components, along with studies to determine the effect of annealing on crystallinity and the occurrence of oxidative reactions. Results showed that isothermal annealing at 250 °C for 18 h improved the storage modulus of all selected grades (neat and reinforced) of PPS at temperatures above T g . Annealing led to an overall increase in the degree of crystallinity, with secondary crystallization taking place. Although oxidative structural changes were observed to occur more on the surface of the PPS parts, they primarily influenced the size of crystals formed and did not significantly alter the degree of crystallinity at various regions within the sample.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A meshing framework for digital twins for extrusion based additive manufacturing

Additive manufacturing (AM) allows for manufacturing of complex three-dimensional geometries not typically realizable with standard manufacturing practices. The internal microstructure of AM components has a significant impact on mechanical, vibrational, and shock properties and permits richer design space when this is controllable. Due to complex interactions of internal geometry of an extrusion-based AM component, it is common practice to assume homogeneous behavior or to perform characterization testing on specific toolpath configurations. To avoid testing or material waste, it is necessary to develop a consistently accurate numerical simulation framework with relevant boundary value problems that can handle the complicated geometry of internal material microstructure present in AM components. Herein, a framework is proposed to directly create computational meshes suitable for finite element analysis (FEA) of the fine-scale features generated from extrusion-based AM tool paths to maintain a strong process–structure–property-performance linkage. This mesh can be manually or automatically analyzed using standard FEA simulations such as quasi-static preloading or modal analysis. The framework allows an in-silico assessment of a target AM geometry where fine-scale features greatly impact quantities of design interest such as in soft elastomeric lattices where toolpath infill can greatly influence the self-contact of a structure in compression, which we use as a motivating exemplar. This approach greatly reduces both time and resource waste present in traditional build and test design cycles for non-intuitive design spaces, and acts as a tool for use in the production of a key component of a digital twin, a mesh suitable for finite element analysis. In conclusion, it also further allows for the exploration of toolpath infill to optimize component properties beyond simple linear properties such as density and stiffness.

Additive manufacturing↗
DOE OSTI2025

Microstructural features underpinning the mechanical behavior of powder metallurgy Cr-based alloys

Refractory materials such as Cr-based alloys offer the potential of enhanced elevated temperature performance but have been limited by their poor formability. However, powder metallurgy has been shown to be a viable pathway to fabricate these alloys. Nanophase separation sintering (NPSS) in particular has been used in the literature to accelerate the densification of powder metallurgy Cr- and W-based alloys. Here, we explore microstructure evolution during NPSS in a binary Cr 85 Ni 15 alloy consolidated via (i) cold pressing & pressureless sintering and (ii) hot isostatic pressing followed by hot extrusion & hot upsetting, and the role of these different processing routes on resulting material properties. The alloy lacked room temperature tensile ductility regardless of consolidation process, with multi-length scale characterization, including scanning electron microscopy, transmission electron microscopy, atom probe tomography, X-ray diffraction, and uniaxial tensile testing, revealing that brittleness was due to intrinsically poor Cr grain boundary cohesion. Tensile testing conducted at 760 °C showed marked strength reduction for the extruded & upset (94 %) condition compared to the pressed & sintered (18 %). The formation of orthorhombic CrNi 2 intermetallics functioned as precipitate strengtheners and prevented elevated temperature softening in the pressed and sintered condition. The findings offer foundational insights into aiding the future development of Cr-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Review of additive manufacturing and densification techniques for the net- and near net-shaping of geometrically complex silicon nitride components

Silicon nitride (Si 3 N 4 ) is an advantageous material due its unique combination of mechanical, thermal, chemical, and electrical properties both at ambient and elevated temperatures. Because of these properties there are a wide range of applications for Si 3 N 4 components. Applications include heat exchangers, environmental barrier coatings, osteointegration scaffolds, radomes, and integrated circuitry. Furthermore, such applications often require geometric complexity for efficient and/or effective operation. However, traditional ceramics processing methods such as hot-pressing or die extrusion are typically limited to simple axis-symmetric shapes. With the advent of additive manufacturing, there has been significant advancement into the forming of geometrically complex Si 3 N 4 components. This review documents additive manufacturing advancements that have demonstrated, or are capable of, fabricating Si 3 N 4 components with complex geometry.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Fiber motion in highly confined flows of carbon fiber and non-Newtonian polymer [Advanced modeling of non-Newtonian polymer and carbon fibers]

Inks compounded of short carbon fibers suspended in polymer resin can be extruded to produce composite materials during additive manufacturing or 3D printing processes. The flow process induces anisotropic orientation of the fibers which is set into the matrix and significantly affects the mechanical and physical properties of the final product. Therefore, the flow of fiber suspensions needs to be understood in order to predict the orientation distribution of the fibers during such manufacturing processes. There is still a lack of knowledge for extrusion of the complex mixture of a non-Newtonian polymer containing a high-volume fraction of fibers with high fiber aspect ratio, where both inter-particle, fluid-particle and fiber-wall interactions are computationally evaluated. This paper presents predictive numerical simulations and experimental results of such confined flow in a concentrated regime. The code is based on Lagrange multiplier technique and resolves each particle and interaction between the fibers and surrounding fluid and nozzle walls. We investigate numerically how the fiber length impacts the fiber alignment during extrusion. We found that a fiber length above 67% of the nozzle's diameter induces dramatic change in the fiber flow, causing fibers to concentrate at the nozzle boundaries with very low concentration of fibers in the center of the nozzle. It was found that the best fiber alignment is reached for fiber lengths equal to 40–50% of the nozzle diameters. Numerical findings are supported by experimental results. In conclusion, this work improves understanding of fiber orientation during 3D printing and is an important milestone for the prediction of the complex mechanical properties of additively manufactured fiber composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Lignetics CRADA closeout report

Lignetics is one of the leading domestic producers of wood pellet fuels used for domestic heating. The company also produces pellets for other applications including animal bedding. The primary feedstock used for the production of Lignetics products is woody biomass. To improve the economics of pellet production, Lignetics is evaluating advanced preprocessing technologies developed by researchers at INL. In the proposed project, INL and Lignetics will work collaboratively to assess the feasibility of integrating INL’s advanced preprocessing technologies (fractional milling, high moisture pelleting and low temperature drying) in Lignetics production facilities. The successful completion of the project relies on the integration of the fractional milling and high moisture pelleting (HMP) process and low temperature drying to improve the economics of woody biomass pellet production for use in biofuel and bioproduct applications. In the HMP process, the biomass loses some moisture during compression and extrusion through the pellet die due frictional heat developed. Also, as pellets have a definite size and shape, they can be further dried in low temperature grain or belt dryers. Belt dryers are better suited to take advantage of low-grade and waste heat because they operate at lower temperatures than rotary dryers (Tumuluru et al.) Rotary dryers, for example, typically require inlet temperatures of 260°C, but more optimally operate around 400°C. In contrast, the inlet temperature of a belt dryer, such as a commercially available vacuum dryer, can be as low as 10°C above the ambient temperature, although more typically they operate at higher temperatures, between 90°C and 200°C. Because of their lower temperature operation, fire hazards and emissions to the air are lower for belt dryers in addition to reducing drying and overall pelleting costs, INL’s technology also has potential to reduce emissions at Lignetics facilities.

09 BIOMASS FUELS↗