Engineering aspects of control system design via the ''direct method'' of Liapunov
Control system design for plants developed into engineering technique via direct method of Liapunov
PRODUCTION ENGINEERING↗
SEARCH · Engineering Papers
Results for “Engineering method”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Application of differential similarity to finding nondimensional groups important in tests of cooled engine components
The method of differential similarity is applied to the partial differential equations and boundary conditions which govern the temperature, velocity, and pressure fields in the flowing gases and the solid stationary components in air-cooled engines. This procedure yields the nondimensional groups which must have the same value in both the test rig and the engine to produce similarity between the test results and the engine performance. These results guide the experimentalist in the design and selection of test equipment that properly scales quantities to actual engine conditions. They also provide a firm fundamental foundation for substantiation of previous similarity analyses which employed heuristic, physical reasoning arguments to arrive at the nondimensional groups.
Sucec, J.↗
Composite load spectra for select space propulsion structural components
The work performed to develop composite load spectra (CLS) for the Space Shuttle Main Engine (SSME) using probabilistic methods. The three methods were implemented to be the engine system influence model. RASCAL was chosen to be the principal method as most component load models were implemented with the method. Validation of RASCAL was performed. High accuracy comparable to the Monte Carlo method can be obtained if a large enough bin size is used. Generic probabilistic models were developed and implemented for load calculations using the probabilistic methods discussed above. Each engine mission, either a real fighter or a test, has three mission phases: the engine start transient phase, the steady state phase, and the engine cut off transient phase. Power level and engine operating inlet conditions change during a mission. The load calculation module provides the steady-state and quasi-steady state calculation procedures with duty-cycle-data option. The quasi-steady state procedure is for engine transient phase calculations. In addition, a few generic probabilistic load models were also developed for specific conditions. These include the fixed transient spike model, the poison arrival transient spike model, and the rare event model. These generic probabilistic load models provide sufficient latitude for simulating loads with specific conditions. For SSME components, turbine blades, transfer ducts, LOX post, and the high pressure oxidizer turbopump (HPOTP) discharge duct were selected for application of the CLS program. They include static pressure loads and dynamic pressure loads for all four components, centrifugal force for the turbine blade, temperatures of thermal loads for all four components, and structural vibration loads for the ducts and LOX posts.
Newell, J. F.↗
Sa-9, 8, and 10 dispersion analysis
Saturn 8, 9, and 10 launch vehicles - dispersions and application to nominal trajectory, mission objectives, root sum square method, and engine- out capability
TRAJECTORY↗
Engineering study to determine feasible methods of simulating planetary albedo and radiation effects upon the thermal balance of spacecraft Final report
Planetary radiation and albedo effects on thermal balance of spacecraft orbiting Mars and Venus
MARS ATMOSPHERE↗
A novel method for studying heterogeneous reactions during simulated engine shutdown conditions
Propellant low temperature preignition reactions during simulated engine shutdown conditions, discussing IR spectroscopic observation method
Dauerman, L.↗
Trajectory optimization techniques in chemical reaction engineering. I - Boundary condition iteration methods
Boundary condition iteration methods in chemical process plant optimal design and control, considering simplicity and ease of programming, computation time and storage requirements
Coull, J.↗
Study on the applicability of a precise, accurate method for rapid evaluation of engine and lubricant performance
The development of a procedure for obtaining data related to wear metal determinations in used lubricants is discussed. The procedure makes it possible to obtain rapid, simultaneous determinations of a number of wear metals at levels of parts per thousand to low parts per billion using a small amount of sample. The electrode assembly and instrumentation used in the process are described. Samples of data obtained from tests conducted under controlled conditions are tabulated.
Kinard, J. T.↗
Effect of symmetrical vortex shedding on the longitudinal aerodynamic characteristics of wing-body-tail combinations
An engineering prediction method for determining the longitudinal aerodynamic characteristics of wing-body-tail combinations is developed. The method includes the effects of nonlinear aerodynamics of components and the interference between components. Nonlinearities associated with symmetrical vortex shedding from the nose of the body are considered as well as the nonlinearities associated with the separation vortices from the leading edges and side edges of the lifting surfaces. The wing and tail characteristics are calculated using lifting surface theories which include effects of incidence, camber, twist, and induced velocities from external sources of disturbance such as bodies and vortices. The lifting surface theories calculate the distribution of leading edge and side edge suction which is converted to vortex lift using the Polhamus suction analogy. Correlation curves are developed to determine the fraction of the theoretical suction force which is converted into vortex lift. The prediction method is compared with experimental data on a variety of aircraft configurations to assess the accuracy and limitations of the method.
Mendenhall, M. R.↗
Prediction of static aerodynamic characteristics for slender bodies alone and with lifting surfaces to very high angles of attack
An engineering-type method is presented for computing normal-force and pitching-moment coefficients for slender bodies of circular and noncircular cross section alone and with lifting surfaces. In this method, a semi-empirical term representing viscous-separation crossflow is added to a term representing potential-theory crossflow. For many bodies of revolution, computed aerodynamic characteristics are shown to agree with measured results for investigated free-stream Mach numbers from 0.6 to 2.9. The angles of attack extend from 0 deg to 180 deg for M = 2.9 from 0 deg to 60 deg for M = 0.6 to 2.0. For several bodies of elliptic cross section, measured results are also predicted reasonably well over the investigated Mach number range from 0.6 to 2.0 and at angles of attack from 0 deg to 60 deg. As for the bodies of revolution, the predictions are best for supersonic Mach numbers. For body-wing and body-wing-tail configurations with wings of aspect ratios 3 and 4, measured normal-force coefficients and centers are predicted reasonably well at the upper test Mach number of 2.0. Vapor-screen and oil-flow pictures are shown for many body, body-wing and body-wing-tail configurations. When spearation and vortex patterns are asymmetric, undesirable side forces are measured for the models even at zero sideslip angle. Generally, the side-force coefficients decrease or vanish with the following: increase in Mach number, decrease in nose fineness ratio, change from sharp to blunt nose, and flattening of body cross section (particularly the body nose).
Jorgensen, L. H.↗
Calculation of unsteady two-dimensional laminar and turbulent boundary layers with fluctuations in external velocity
A numerical method is proposed for calculating unsteady two-dimensional laminar and turbulent boundary layers with allowance for fluctuations in external flow velocity. An eddy-viscosity formulation is used to model the Reynolds shear stress term appropriate to turbulent flow, and the governing boundary layer equations are solved by a two-point finite-difference scheme. For illustration, the method is applied to the calculation of the phase angles between the shear stress at the wall and an oscillating external laminar boundary layer on a flat plate. The effectiveness of the method (for engineering purposes) is demonstrated by comparing calculations for turbulent flows with experimental data.
Cebeci, T.↗
Evacuated load-bearing high performance insulation study
A light weight, vacuum jacketed, load bearing cryogenic insulation system was developed and tested on a 1.17-m (46-in.) spherical test tank. The vacuum jacket consists of 0.08 mm (0.003 in.) thick 321 stainless steel formed into a wedge design that allows elastic jacket movements as the tank shrinks (cools) or expands (warms up or is pressurized). Hollow glass spheres, approximately 80 micrometers in diameter with a bulk density of 0.069 g/cc (4.3 lb cubic foot), provide the insulating qualities and one atmosphere load bearing capability required. The design, fabrication, and test effort developed the manufacturing methods and engineering data needed to scale the system to other tank sizes, shapes, and applications. The program demonstrated that thin wall jackets can be formed and welded to maintain the required vacuum level of .013 Pa yet flex elastically for multiple reuses. No significant shifting or breakage of the microspheres occurred after 13 simulated Space Tug flight cycles on the test tank and a hundred 1 atmosphere load cycles in a flat plate calorimeter. The test data were then scaled to the Space Tug LO2 and LH2 tanks, and weight, thermal performance, payload performance, and costs were compared with a helium purged multilayer insulation system.
Parmley, R. T.↗
A review and assessment of the stress-intensity factors for surface cracks
The stress-intensity factor solutions proposed for a surface crack in a finite plate subjected to uniform tension are reviewed. Fourteen different solutions for the stress-intensity factors are compared. These solutions were obtained over the past 16 years using approximate analytical methods, experimental methods, and engineering estimates. The accuracy is assessed of the various solutions by correlating fracture data on surface-cracked tension specimens made of a brittle epoxy material. Fracture of the epoxy material was characterized by a constant value of stress-intensity factor at failure. Thus, the correctness of the various solutions is judged by the variations in the stress-intensity factors at failure. The solutions were ranked in order of minimum standard deviation. The highest ranking solutions correlated 95 percent of data analyzed within + or - 10 percent, whereas the lowest ranking solutions correlated 95 percent of data analyzed within + or - 20 percent. However, some solutions could be applied to all data considered, whereas others are limited with respect to crack shapes and crack sizes that could be analyzed.
Newman, J. C., Jr.↗
A program to compute three-dimensional subsonic unsteady aerodynamic characteristics using the doublet lattic method, L216 (DUBFLX). Volume 1: Engineering and usage
The program input presented consists of configuration geometry, aerodynamic parameters, and modal data; output includes element geometry, pressure difference distributions, integrated aerodynamic coefficients, stability derivatives, generalized aerodynamic forces, and aerodynamic influence coefficient matrices. Optionally, modal data may be input on magnetic file (tape or disk), and certain geometric and aerodynamic output may be saved for subsequent use.
Richard, M.↗
Wind-tunnel measurements and comparison with flight of the boundary layer and heat transfer on a hollow cylinder at Mach 3
The wind tunnel tests were conducted both with and without boundary layer trips at Mach 3 and nominal free stream Reynolds numbers per meter ranging from 3.3 x 10 the 6th power. Instrumentation consisted of pressure orifices, thermocouples, a boundary layer pitot pressure rake, and a floating element skin friction balance. Measurements from both wind tunnel and flight were compared with existing engineering prediction methods.
Stallings, R. L., Jr.↗
Application of the MNA design method to a nonlinear turbofan engine
Using nonlinear digital simulation as a representative model of the dynamic operation of the QCSEE turbofan engine, a feedback control system is designed by variable frequency design techniques. Transfer functions are generated for each of five power level settings covering the range of operation from approach power to full throttle (62.5% to 100% full power). These transfer functions are then used by an interactive control system design synthesis program to provide a closed loop feedback control using the multivariable Nyquist array and extensions to multivariable Bode diagrams and Nichols charts.
Leininger, G. G.↗
A review and assessment of the stress-intensity factors for surface cracks
The stress-intensity factor solutions proposed for a surface crack in a finite plate subjected to uniform tension are reviewed. Fourteen different solutions obtained over the past 16 years using approximate analytical methods, experimental methods, and engineering estimates are compared. The accuracy of the various solutions is assessed by correlating fracture data on surface-cracked tension specimens made of a brittle epoxy material. Fracture of the epoxy material was characterized by a constant value of stress-intensity factor as failure. Thus, the correctness of various solutions is judged by the variations in the stress-intensity factors at failure. The solutions were ranked in order of minimum standard deviation. The highest ranking solutions correlated 95% of data analyzed within + or - 10% whereas the lowest ranking solutions correlated 95% of data analyzed within + or - 20%. Some solutions could be applied to all data considered, whereas others were limited with respect to crack shapes and crack sizes that could be analyzed.
Newman, J. C., Jr.↗
Helicopter theory
A comprehensive presentation is made of the engineering analysis methods used in the design, development and evaluation of helicopters. After an introduction covering the fundamentals of helicopter rotors, configuration and operation, rotary wing history, and the analytical notation used in the text, the following topics are discussed: (1) vertical flight, including momentum, blade element and vortex theories, induced power, vertical drag and ground effect; (2) forward flight, including in addition to momentum and vortex theory for this mode such phenomena as rotor flapping and its higher harmonics, tip loss and root cutout, compressibility and pitch-flap coupling; (3) hover and forward flight performance assessment; (4) helicopter rotor design; (5) rotary wing aerodynamics; (6) rotary wing structural dynamics, including flutter, flap-lag dynamics ground resonance and vibration and loads; (7) helicopter aeroelasticity; (8) stability and control (flying qualities); (9) stall; and (10) noise.
Johnson, W.↗