SEARCH · Engineering Papers

Results for “Energetic material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1997

Sample Diluter for Detecting Hypergolic Propellants and Other Toxic or Hazardous Gases

Hardware was developed to dilute vapor samples of purged hypergolic propellants (with air) into the range of existing instruments for detection of such toxic vapors. Since these detectors are normally used to monitor at the threshold limit value (TLV), most do not have quantitative capability at percent levels which relate to lower explosion limit (LEL) and fire hazards. For example, the upper limits of Energetic Sciences (ESI) 6000 series detectors used at KSC are 200 parts per million (ppm) for monomethyl hydrazine (MMH) and 500 ppm for nitrogen dioxide (NO2) arising from decomposition of nitrogen tetroxide (N2O4). Orbiter Processing Facility (OPF) personnel servicing Shuttle thrusters need to measure up to 250 ppm MMH and 7,500 ppm NO2 with portable, intrinsically safe instruments. Our objective was to quickly fabricate a sample diluter out of existing materials as a temporary measure while other parallel efforts were conducted to provide a commercial or in-house-developed instrument to detect high propellant levels. A 3 to 1 diluter would bring 500 ppm MMH into the range of the existing fuel ESI, and a 30 to 1 diluter would do the same for NO2. In this way, familiar equipment already available would be used, resulting in minimal paperwork, safety, and training impacts and low cost. An MMH vapor sample-diluter was constructed from a 1/4-inch Kynar tee, along with specially designed lengths of sample and dilution tubing. The sample line was 3 feet of Bev-A-Line 4, 1/4-inch tube leading to the straight run of the tee. The side run of the tee had a 17-inch length of Bev-A-Line 4, 1/4-inch tube, for nominal 3 to 1 dilution. A gas sample bag was prepared and assayed at 113 ppm ppm MMH, and diluted vapor samples were assayed at 39.5 ppm, or a measured dilution of 2.9 to 1. For NO2, a 316 stainless steel (SS) 1/8-inch tee with 49.5 inches of coiled, 1/8-inch outside diameter (OD) 316 SS tubing was used as the sampling end of the dilution system. The side run of the tee was open. The measured dilution ratio, based on the input value of 6,480 ppm NO2, and the average output value of 233 ppm, was 28 to 1. Thus, sample-diluters were successful in diluting concentrated hypergolic propellant vapors, both MMH and N2O4 into the ranges of existing TLV detectors.

Barile, R. G.↗

NASA NTRS1988

Bimodal abundances in the energetic particles of solar and interplanetary origin

This letter reports the first results from an examination of the daily-averaged abundances of the elements from H through Fe as well as electrons and isotopes of He in energetic particles observed in interplanetary space by the ISEE 3 spacecraft over an 8.5 yr period. The abundances of heavy elements such as Fe/O show, for the first time, clear evidence of the presence of two distinct populations of particles. Earlier observations could be interpreted as extreme variations within a single population. The population with enhanced Fe/O shows correlated enhancements in He-3/He-4, p/e, and He/H. This population is consistent with material that has been processed to high temperatures in the impulsively heated regions of solar flares. The second population, with more normal abundances, is probably accelerated from ambient material by coronal and interplanetary shocks.

Reames, Donald V.↗

NASA NTRS1996

NASA's Technical Handbook for Avoiding On-Orbit ESD Anomalies Due to Internal Charging Effects

This paper describes NASA-HDBK-4002, "Avoiding Problems Caused by Spacecraft On-Orbit Internal Charging Effects". The handbook includes a description of internal charging and why it is of concern to spacecraft designers. It also suggests how to determine when a project needs to consider internal spacecraft charging, it contains an electron penetration depth chart, rationale for a critical electron flux criterion, a worst-case geosynchronous electron plasma spectrum, general design guidelines, quantitative design guidelines, and a typical materials characteristics list. Appendices include a listing of some environment codes, electron transport codes, a discussion of geostationary electron plasma environments, a brief description of electron beam and other materials tests, and transient susceptibility tests. The handbook will be in the web page, hftp://standards.nasa.gov. A prior document, NASA TP2361 "Design Guidelines for Assessing and controlling Spacecraft Charging Effects", 1984, is in use to describe mitigation techniques for the effects of surface charging of satellites in space plasma environments. HDBK-4002 is meant to complement 2361 and together, the pair of documents describe both cause and mitigation designs for problems caused by energetic space plasmas.

Whittlesey, Albert↗

NASA NTRS1991

Long-term changes in composition of solar particles implanted in extraterrestrial materials

Analysis of lunar surface samples for elements implanted therein by solar corpuscular radiation reveals evidence for the following compositional changes over a time period between 1.5 and 3 Gyr: 50-percent decreases in the ratios He-4/Ar-36 and Xe/Ar-36; a 20-percent increase in the ratio He-3/He-4; a 3-percent increase in the ratio Ne-20/Ne-22; and a 50-percent increase in the ratio N-15/N-14. The causes of these changes are not resolved at this time but may include (1) a change in acceleration conditions of the solar wind, (2) a change in flux of solar energetic particles relative to that of the solar wind, and (3) a change in composition of the solar convective zone. There is good evidence for a long-term decrease in the solar-wind flux.

Kerridge, J. F.↗

NASA NTRS1979

Survey of ion plating sources

Ion plating is a plasma deposition technique where ions of the gas and the evaporant have a decisive role in the formation of a coating in terms of adherence, coherence, and morphological growth. The range of materials that can be ion plated is predominantly determined by the selection of the evaporation source. Based on the type of evaporation source, gaseous media and mode of transport, the following will be discussed: resistance, electron beam sputtering, reactive and ion beam evaporation. Ionization efficiencies and ion energies in the glow discharge determine the percentage of atoms which are ionized under typical ion plating conditions. The plating flux consists of a small number of energetic ions and a large number of energetic neutrals. The energy distribution ranges from thermal energies up to a maximum energy of the discharge. The various reaction mechanisms which contribute to the exceptionally strong adherence - formation of a graded substrate/coating interface are not fully understood, however the controlling factors are evaluated. The influence of process variables on the nucleation and growth characteristics are illustrated in terms of morphological changes which affect the mechanical and tribological properties of the coating.

Spalvins, T.↗

NASA NTRS1983

Properties of ices and grains - An experimental study

Proton irradiation of a variety of ice mixtures was carried out to study the effect of galactic cosmic ray irradiation of comets in the Oort Cloud. Three significant effects were noted: (1) production of new molecules; (2) production of a more energetic ice at low temperatures; (3) production of a non-volatile, complex organic residue. These phenomena suggest various effects on new comets approaching the sun including enhanced activity. Experiments on the condensation of silicate grains provide information on the condensation mechanism and properties of grains. Controlled annealing of the amorphous condensates shows how crystallization occurs. Infrared spectra of different stages of crystallization contain features that may identify composition, structure and history of refractory material.

Donn, B.↗

NASA NTRS1981

Singly charged energetic helium emitted in solar flares

First direct charge state measurements of 0.41-1.05 MeV per nucleon helium accelerated at the sun reveal surprisingly large abundances of singly ionized helium, with typical He(+)/He(++) ratios between 0.04 and 0.21. This unexpected overabundance of He(+) was observed in each of the three large solar-flare particle events which occurred between 1978 August and 1979 October. The data were obtained with the Max-Planck-Institut/University of Maryland Experiment on board the ISEE-3 spacecraft. The observations suggest either strong coronal temperature inhomogeneities including cool regions of approximately 100,000 K or injection of 'cold' chromospheric/photospheric material into the flare acceleration region.

Hovestadt, D.↗

NASA NTRS2014

Computation of Cosmic Ray Ionization and Dose at Mars: a Comparison of HZETRN and Planetocosmics for Proton and Alpha Particles

The ability to evaluate the cosmic ray environment at Mars is of interest for future manned exploration. To support exploration, tools must be developed to accurately access the radiation environment in both free space and on planetary surfaces. The primary tool NASA uses to quantify radiation exposure behind shielding materials is the space radiation transport code, HZETRN. In order to build confidence in HZETRN, code benchmarking against Monte Carlo radiation transport codes is often used. This work compares the dose calculations at Mars by HZETRN and the Geant4 application Planetocosmics. The dose at ground and the energy deposited in the atmosphere by galactic cosmic ray protons and alpha particles has been calculated for the Curiosity landing conditions. In addition, this work has considered Solar Energetic Particle events, allowing for the comparison of varying input radiation environments. The results for protons and alpha particles show very good agreement between HZETRN and Planetocosmics.

Gronoff, Guillaume↗

NASA NTRS1988

The origin and energetics of CTB 80

Deep narrow-band images of the core of the unusual supernova remnant CTB 80 are presented, and the origin and energetics of the remnant are discussed. Based on a description of the core as a wind-blown bubble or bow shock around a pulsar, a scenario is presented relating the core and extended components to a single supernova explosion about 100,000 yr ago. The physical nature of the interface between the pulsar wind and the ambient thermal plasma is considered, and it is concluded that the pulsar is probably moving through shock-compressed material associated with the evolved remnant. It is argued that the core geometry is probably a bow shock viewed partially face-on.

Hester, J. Jeff↗

NASA NTRS2008

Controlling Charging and Arcing on a Solar Powered Auroral Orbiting Spacecraft

The Global Precipitation Measurement satellite (GPM) will be launched into a high inclination (65 degree) orbit to monitor rainfall on a global scale. Satellites in high inclination orbits have been shown to charge to high negative potentials, with the possibility of arcing on the solar arrays, when three conditions are met: a drop in plasma density below approximately 10,000 cm(exp -3), an injection of energetic electrons of energy more that 7-10 keV, and passage through darkness. Since all of these conditions are expected to obtain for some of the GPM orbits, charging calculations were done using first the Space Environment and Effects (SEE) Program Interactive Spacecraft Charging Handbook, and secondly the NASA Air-force Spacecraft Charging Analyzer Program (NASCAP-2k). The object of the calculations was to determine if charging was likely for the GPM configuration and materials, and specifically to see if choosing a particular type of thermal white paint would help minimize charging. A detailed NASCAP-2k geometrical model of the GPM spacecraft was built, with such a large number of nodes that it challenged the capability of NASCAP-2k to do the calculations. The results of the calculations were that for worst-case auroral charging conditions, charging to levels on the order of -120 to -230 volts could occur on GPM during night-time, with differential voltages on the solar arrays that might lead to solar array arcing. In sunlit conditions, charging did not exceed -20 V under any conditions. The night-time results were sensitive to the spacecraft surface materials chosen. For non-conducting white paints, the charging was severe, and could continue unabated throughout the passage of GPM through the auroral zone. Somewhat conductive (dissipative) white paints minimized the night-time charging to levels of -120 V or less, and thus were recommended for GPM thermal control. It is shown that the choice of thermal control paints is important to prevent arcing on high inclination orbiting spacecraft solar arrays as well as for GEO satellites, even for solar array designs chosen to minimize arcing.

Ferguson, Dale C.↗

NASA NTRS1987

Simulation studies for surfaces and materials strength

Three different investigations based on computer simulations were carried out. Simulation calculations were performed using model potentials with two- and three-body interactions which were represented by the Mie and the Axilrod-Teller potentials, respectively. In the first part, to analyze stability criteria for simple crystals, a parametrical investigation was performed and stability regions for five different crystalline structures were determined with respect to potential energy parameters. To simulate some of the basic surface processes such as diffusion and nucleation, in the second and third parts, silicon surfaces were considered as a specific example. In these studies diffusion of adatoms on stepped surfaces were simulated and energetics associated with the formation of kink sites were calculated.

Halicioglu, Timur↗

NASA NTRS1985

The energy dependence of the neon-22 excess in the cosmic radiation

It has been recognized now for some time that the heavy neon isotope, neon-22, is overabundant by a factor of 3 to 4 with respect to neon-22 in the cosmic ray source compared to the ratio of these isotopes in the Solar System. In view of the otherwise remarkable similarity of the chemical composition of the cosmic ray source and the composition of the Solar Energetic Particles, the anomaly regarding the neon isotopes is so much more striking. The observed excess of neon-22 is too large to be explained as a result of the chemical evolution of the Galaxy since the formation of the Solar System. Further information on the origin of the neon-22 excess may come from a comparison of the energy spectra of the two neon isotopes. If the cosmic radiation in the solar neighborhood is a mixture of material from several sources, one of which has an excess of neon-22, then the source energy spectra of neon-20 and neon-22 may differ significantly.

Herrstroem, N. Y.↗

NASA NTRS2002

Overview of the Chandra X-Ray Observatory Facility

The Chandra X-Ray Observatory (originally called the Advanced X-Ray Astrophysics Facility - AXAF) is the X-Ray component of NASA's "Great Observatory" Program. Chandra is a NASA facility that provides scientific data to the international astronomical community in response to scientific proposals for its use. The Observatory is the product of the efforts of many organizations in the United States and Europe. The Great Observatories also include the Hubble Space Telescope for space-based observations of astronomical objects primarily in the visible portion of the electromagnetic spectrum, the now defunct Compton Gamma- Ray Observatory that was designed to observe gamma-ray emission from astronomical objects, and the soon-to-be-launched Space Infrared Telescope Facility (SIRTF). The Chandra X-Ray Observatory (hereafter CXO) is sensitive to X-rays in the energy range from below 0.1 to above 10.0 keV corresponding to wavelengths from 12 to 0.12 nanometers. The relationship among the various parts of the electromagnetic spectrum, sorted by characteristic temperature and the corresponding wavelength, is illustrated. The German physicist Wilhelm Roentgen discovered what he thought was a new form of radiation in 1895. He called it X-radiation to summarize its properties. The radiation had the ability to pass through many materials that easily absorb visible light and to free electrons from atoms. We now know that X-rays are nothing more than light (electromagnetic radiation) but at high energies. Light has been given many names: radio waves, microwaves, infrared, visible, ultraviolet, X-ray and gamma radiation are all different forms. Radio waves are composed of low energy particles of light (photons). Optical photons - the only photons perceived by the human eye - are a million times more energetic than the typical radio photon, whereas the energies of X-ray photons range from hundreds to thousands of times higher than that of optical photons. Very low temperature systems (hundreds of degrees below zero Celsius) produce low energy radio and microwave photons, whereas cool bodies like our own (about 30 degrees Celsius) produce infrared radiation. Very high temperatures (millions of degrees Celsius) are one way of producing X-rays.

Weisskopf, M. C.↗

NASA NTRSDate not supplied

Electron Bombardment on Dione: Surface Compositional Effects and Temperature Anomalies

Saturn’s icy moons are composed primarily of water ice with minor other “contaminants,” such as CO2 ice, and a dark component thought to be organics, hematite and/or metallic Fe. The space weathering process of electron bombardment is expected to be particularly important on the surfaces of Saturn’s inner moons (Mimas, Tethys, Dione, and Rhea), as they orbit within Saturn’s inner magnetosphere. Terrains exhibiting thermal anomalies (i.e., colder temperatures in the day and warmer temperatures at night than surrounding areas) correspond to regions of high energy electron bombardment. Energetic electrons impact the surfaces, sintering ice grains together, and this process becomes more effective for increasing particle energies. Solar UV radiation, cosmic rays, dust in-fall, and cold plasma particles trapped in Saturn’s magnetic field also play an important role in altering the nature and the structure of the native surface ices by the implantation of contaminants, ionization, sputtering, and dissociation of water ice molecules. Additionally, CO2 could be sourced from irradiation of dark organic material. Many of these surface alterations are observable in Cassini’s Visible and Infrared Mapping Spectrometer (VIMS) spectra. We used similar methodologies as have been employed in previous works to derive surface temperatures from Cassini’s Composite Infrared Spectrometer (CIRS), which helped to isolate areas where space weathering due to electron bombardment is more predominant. The subtle changes in VIMS spectra were investigated using machine learning techniques. We present here our results for Dione.

C L Young↗

NASA NTRS2002

Experimental Verification of the Theoretical Prediction of the Phase Structure of a Ni-Al-Ti-Cr-Cu Alloy

The Bozzolo-Ferrante-Smith (BFS) method for alloys was applied to the study of NiAl-based materials to assess the effect of alloying additions on structure. Ternary, quaternary and even pentalloys based on NiAl with additions of Ti, Cr and Cu were studied and experimental verification of the theoretical predictions including the phase structure of a Ni-Al-Ti-Cr-Cu alloy is presented. Two approaches were used, Monte Carlo simulations to determine low energy structures, and analytical calculations of the energy of high symmetry configurations which give physical insight into preferred structures. The energetics for site occupancy in ternary and quaternary systems were calculated leading to an indirect determination of solubility limits at 0 K. Precipitate formation with information concerning structure and lattice parameter were also 'observed' computationally and the general characteristics of a Ni-Al-Ti-Cr-Cu alloy were correctly predicted. The results indicate that the BFS method for alloys can be a useful tool for alloy design and can be used to complement experimental alloy design programs.

Wilson, A.↗

NASA NTRSDate not supplied

Electron Bombardment on Dione: Surface Compositional Effects and Temperature Anomalies

Saturn’s icy moons are composed primarily of water ice with minor other “contaminants,” such as CO2 ice, and a dark component thought to be organics, hematite and/or metallic Fe [1]. The space weathering process of electron bombardment is expected to be particularly important on the surfaces of Saturn’s inner moons (Mimas, Tethys, Dione, and Rhea), as they orbit within Saturn’s inner magnetosphere. Terrains exhibiting thermal anomalies (i.e., colder temperatures in the day and warmer temperatures at night than surrounding areas) correspond to regions of high energy electron bombardment [2; 3; 4; 5]. Energetic electrons impact the surfaces, sintering ice grains together, and this process becomes more effective for increasing particle energies [6]. Solar UV radiation, cosmic rays, dust in-fall, and cold plasma particles trapped in Saturn’s magnetic field also play an important role in altering the nature and the structure of the native surface ices by the implantation of contaminants, ionization, sputtering, and dissociation of water ice molecules [7]. Additionally, CO2 could be sourced from irradiation of dark organic material [8]. Many of these surface alterations are observable in Cassini’s Visible and Infrared Mapping Spectrometer (VIMS) spectra [9]. We used similar methodologies as have been employed in previous works [e.g., 10] to derive surface temperatures from Cassini’s Composite Infrared Spectrometer (CIRS), which helped to isolate areas where space weathering due to electron bombardment is more predominant. The subtle changes in VIMS spectra were investigated using machine learning techniques. We present here our results for Dione.

Cindy Lee Young↗

NASA NTRSDate not supplied

Electron Bombardment on Dione: Surface Compositional Effects and Temperature Abnormalities

C L Young↗

NASA NTRSDate not supplied

Hydrated Interplanetary Dust Particles: Implications for Oxygen Reservoirs in the Outer Solar System

A re-evaluation of solar energetic particle (SEP) track densities in interplanetary dust particles (IDPs) show that many are derived from outer solar system parent bodies such as Kuiper belt objects (KBOs) or beyond. Kuiper belt objects are widely believed to represent the frozen remnants from the birth of the solar system. The population of track-rich IDPs include members from both the anhydrous chondritic-porous and hydrated chondritic-smooth classes and earlier work suggested that the hydrated IDPs may represent anhydrous IDP material that was aqueously altered. We are performing systematic studies of the mineralogy, chemistry and isotopic compositions of track-rich IDPs to gain a fuller understanding of the origin and evolution of KBOs. Here, we focus on the identification of hydrated Kuiper belt dust particles that allows for the direct evaluation of their O isotopic compositions and the implications for the oxygen isotopic composition of outer solar system ices.

L. P. Keller↗