Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic Timing Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Dynamic Analysis of Reynolds Number Effects on Trailing Edge Transonic Vortex Shedding and Its Impact on Turbine Blade Aerodynamic Performance

Time-resolved, high-speed self-aligned focusing schlieren images were acquired in the NASA Glenn Research Center Transonic Turbine Blade Cascade facility to help understand the aerodynamic behavior of high-pressure, thick trailing edge turbine blades. The trailing edge thickness of 9% of axial chord tested represents simulated ceramic matrix composite fabrication constraints, which was verified previously to possess a high-loss flow regime at high inlet turbulence conditions over a narrow range of Reynolds numbers and at a fixed design exit Mach number of 0.74. Our high-speed images, which were acquired at 10 distinct Reynolds numbers, show a significant increase in energy from flow oscillations due to transonic vortex shedding at Reynolds numbers corresponding to the high loss conditions. For those conditions, strong acoustic waves turn into shock waves. Spectral Proper Orthogonal Decomposition of the high-speed images shows acoustic waves from trailing edge vortex shedding at all conditions, with increased spectral energy at the high-loss conditions and slightly increasing frequency (about 6%) as a function of Reynolds number. Analysis of potential feedback timing is performed using velocity fields from a previous LES simulation, considering different feedback mechanisms. Most noteworthy is the acoustic/shock-boundary layer interaction mechanism on the suction surface at the blade geometric throat, which likely plays an important role in realistic curved blade passages.

Trailing Edge↗
DOE OSTI2021

Transforming ENERGY through Computational Excellence

Computational methods underpin advancing the science and engineering of energy efficiency, sustainable transportation, renewable power technologies, and developing a knowledge base to optimize energy systems. Researchers with access to enough computing, and the right type, can focus their ingenuity and creativity on addressing the energy challenges. NREL’s advanced computing influence spans several common themes across the Office of Energy Efficiency and Renewable Energy (EERE), including materials discovery, process modeling, fluid dynamics, resource mapping, and analysis of large-scale systems with real-time optimization.

advanced computing↗
DOE OSTI2025

A mathematical approach to using the forgetting curve to evaluate experience and training factors in human reliability analysis

Traditional human reliability analysis (HRA) methods have difficulty dealing with the dynamic nature of factors such as time and rely on static and expert-judgment-based assessments of performance-shaping factors (PSFs) across limited levels. In this study, we introduce a mathematical approach for dynamically evaluating the experience and training PSF. Our proposed method integrates the psychological concept of the “forgetting curve” to evaluate how PSFs are impacted by the number of trainings and the time elapsed since training. To confirm the validity of the model, we provide experimental data fitted by identifying the quantitative relationship between training and human performance. This research enables dynamic and objective assessments, thus reducing reliance on subjective expert judgment and improving the accuracy of HRA.

99 - GENERAL AND MISCELLANEOUS↗
NASA NTRS1978

Sampling analysis for the Earth Radiation Budget Satellite System mission based on orbital coverage and cloud variability

The reported study represents an extension of an investigation by Harrison et al. (1976). Based on the results of sampling studies, two 98 deg inclined orbits coupled with a 56 deg inclination orbit appear to satisfy the science requirements on both regional and zonal scales. The NOAA sun-synchronous satellites in the TIROS-N series could adequately cover the high latitudes and a satellite having an inclination of 56 deg could provide sampling in the mid and low latitude areas where variations in radiation energetics are most dynamic. Attention is given to studies of time and space coverage, zonal evaluations, a regional analysis, and statistics describing the regional variations of cloud cover. A table is presented with data concerning the uncertainty of monthly mean reflected irradiance due to cloud variability for selected northern hemisphere regions.

Harrison, E. F.↗
NASA NTRS1979

Integration Time Required to Extract Accurate Data from Transonic Wind-Tunnel Tests

Because the forces and pressures on wind-tunnel models tested at transonic speeds are not steady, even for static aerodynamic tests, integration time is required to obtain data of acceptable accuracy. The integration time required for both static and dynamic tests is evaluated analytically and confirmed by experimental measurements. It is shown that, for static and dynamic tests, the accuracy obtained is a function of integration time, frequency of the signal, and the ratio of the dynamic amplitude to the full signal of interest. In addition, for the dynamic case, the frequency bandwidth used in analysis is important. Results of this study indicate that, for typical data accuracy desired from models in a large transonic wind tunnel (11- by 11-ft), up to the following integration times are required: static force and moment tests, 0.5 s; static pressure tests, 1 s; flutter tests, 30 to 60 s; and random-dynamic tests, 10 s.

Muhlstein, Lado, Jr.↗
NASA NTRS1987

Analysis of planetary evolution with emphasis on differentiation and dynamics

In order to address the early stages of nebula evolution, a three-dimensional collapse code which includes not only hydrodynamics and radiative transfer, but also the effects of ionization and, possibly, magnetic fields is being addressed. As part of the examination of solar system evolution, an N-body code was developed which describes the latter stages of planet formation from the accretion of planetesimals. To test the code for accuracy and run-time efficiency, and to develop a stronger theoretical foundation, problems were studied in orbital dynamics. A regional analysis of the correlation in the gravity and topography fields of Venus was performed in order to determine the small and intermediate scale subsurface structure.

Kaula, William M.↗
NASA NTRS1989

Dynamics of planetary atmospheres

The overall goal is to illuminate the mechanisms that control weather and climate on the Earth and other planets. Each planet presents its own puzzling behavior - the stability of jets and vortices in Jupiter's otherwise turbulent atmosphere, the superrotation of the Venus atmosphere, the interplay of dust, polar volatiles, and climate change in Mars, the supersonic meteorology of Io, and the counterintuitive equator-to-pole temperature gradients on the outer planets. The data sets are generally those obtained from spacecraft - cloud-tracked winds, radiometrically inferred temperatures, and the results of in situ observations where appropriate. The approach includes both data analysis and modeling, ranging from analytic modeling to time-dependent numerical modeling of atmospheric dynamics. The latter approach involves the use of supercomputers such as the San Diego Cray. Progress is generally made when a model with a small number of free parameters either fits a data set that has a large number of independent observations or applies to several planets at once.

Ingersoll, Andrew P.↗
NASA NTRS2013

Global Weather States and Their Properties from Passive and Active Satellite Cloud Retrievals

In this study, the authors apply a clustering algorithm to International Satellite Cloud Climatology Project (ISCCP) cloud optical thickness-cloud top pressure histograms in order to derive weather states (WSs) for the global domain. The cloud property distribution within each WS is examined and the geographical variability of each WS is mapped. Once the global WSs are derived, a combination of CloudSat and Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) vertical cloud structure retrievals is used to derive the vertical distribution of the cloud field within each WS. Finally, the dynamic environment and the radiative signature of the WSs are derived and their variability is examined. The cluster analysis produces a comprehensive description of global atmospheric conditions through the derivation of 11 WSs, each representing a distinct cloud structure characterized by the horizontal distribution of cloud optical depth and cloud top pressure. Matching those distinct WSs with cloud vertical profiles derived from CloudSat and CALIPSO retrievals shows that the ISCCP WSs exhibit unique distributions of vertical layering that correspond well to the horizontal structure of cloud properties. Matching the derived WSs with vertical velocity measurements shows a normal progression in dynamic regime when moving from the most convective to the least convective WS. Time trend analysis of the WSs shows a sharp increase of the fair-weather WS in the 1990s and a flattening of that increase in the 2000s. The fact that the fair-weather WS is the one with the lowest cloud radiative cooling capability implies that this behavior has contributed excess radiative warming to the global radiative budget during the 1990s.

histograms↗
NASA NTRS1977

Dynamic response and stability analysis of flexible, multibody systems

A general version of Lagrange's equations, including auxiliary nonholonomic, rheonomic conditions of constraint, is used in the dynamic simulation and stability analysis of interconnected flexible bodies. Modeling of the nonlinear flexible/rigid dynamic coupling effects, the interaction forces/torques, and the elastic deformation effects is discussed. A digital computer program is developed to obtain time-domain solution for the nonlinear response of systems represented as a collection of individual bodies, numerical linearization of system-governing equations, time-domain solution for the perturbation response about a nominal state, and a frequency-domain stability analysis corresponding to the linearization. The digital simulation code is employed to study the dynamic behavior of a typical satellite and a spacecraft with deployable experiment booms.

Bodley, C. S.↗
NASA NTRS1989

Unsteady Euler airfoil solutions using unstructured dynamic meshes

Two algorithms for the solution of the time-dependent Euler equations are presented for unsteady aerodynamic analysis of oscillating airfoils. Both algorithms were developed for use on an unstructured grid made up of triangles. The first flow solver involves a Runge-Kutta time-stepping scheme with a finite-volume spatial discretization that reduces to central differencing on a rectangular mesh. The second flow solver involves a modified Euler time-integration scheme with an upwind-biased spatial discretization based on the flux-vector splitting of Van Leer. The paper presents descriptions of the Euler solvers and dynamic mesh algorithm along with results which assess the capability.

Batina, John T.↗
NASA NTRS1992

Aeroelastic analysis of advanced propellers using an efficient Euler solver

A 3D Euler solver is coupled with a 3D structural dynamics model to investigate flutter of propfans. A hybrid scheme is used to reduce computational time for the Euler equations and a normal mode analysis is used for flutter calculations. Experimental and calculated flutter results are compared for an advanced propeller propfan which experienced flutter at transonic tip relative velocities. The predicted flutter calculations are in close agreement with the experimental data. A structural damping value of 0.5 percent was required to predict the behavior observed in the experiment. Computations show that the flutter behavior is dominated by the second mode, but coupling with the first mode is required. The addition of other modes to the calculations did not affect the flutter behavior.

Srivastava, R.↗
NASA NTRS1988

The effect of rotor dynamics on a flywheel stack energy storage system

The paper presents a dynamic analysis of a magnetic-bearing stack system consisting of a single flywheel supported by two magnetic bearings. Real-time plots from a computer simulation are used to show the effect of dynamic coupling on the torque response, and the frequency response is used to determine the resonance frequencies of the stack system. It is found that system stability depends on the flywheel speed.

Jayaraman, Chaitanya P.↗
DOE OSTI2024

Structural Impact of Grid-Forming Inverters on Power System Coherency

This paper addresses the following fundamental research question: how does the integration of grid-forming inverters (GFMs) replacing conventional synchronous generators (SGs) impact the slow coherent eigen-structure and the low frequency oscillatory behavior of future power systems? Due to time-scale separated dynamics, generator states inside a coherent area synchronize over a fast time-scale due to stronger coupling, while the areas themselves synchronize over a slower time scale. Our mathematical analysis shows that due to the large-scale integration of GFMs, the weighted Laplacian structure of the frequency dynamics is preserved, however, the entries of the Laplacian may be significantly modified based on the location and penetration levels of the GFMs. This can impact and potentially significantly alter the coherency structure of the system. We have validated our findings with numerical results using the IEEE 68-bus test system.

Mukherjee, Sayak [BATTELLE (PACIFIC NW LAB)]↗
NASA NTRS2008

Mars Reconnaissance Orbiter Uplink Analysis Tool

This software analyzes Mars Reconnaissance Orbiter (MRO) orbital geometry with respect to Mars Exploration Rover (MER) contact windows, and is the first tool of its kind designed specifically to support MRO-MER interface coordination. Prior to this automated tool, this analysis was done manually with Excel and the UNIX command line. In total, the process would take approximately 30 minutes for each analysis. The current automated analysis takes less than 30 seconds. This tool resides on the flight machine and uses a PHP interface that does the entire analysis of the input files and takes into account one-way light time from another input file. Input flies are copied over to the proper directories and are dynamically read into the tool s interface. The user can then choose the corresponding input files based on the time frame desired for analysis. After submission of the Web form, the tool merges the two files into a single, time-ordered listing of events for both spacecraft. The times are converted to the same reference time (Earth Transmit Time) by reading in a light time file and performing the calculations necessary to shift the time formats. The program also has the ability to vary the size of the keep-out window on the main page of the analysis tool by inputting a custom time for padding each MRO event time. The parameters on the form are read in and passed to the second page for analysis. Everything is fully coded in PHP and can be accessed by anyone with access to the machine via Web page. This uplink tool will continue to be used for the duration of the MER mission's needs for X-band uplinks. Future missions also can use the tools to check overflight times as well as potential site observation times. Adaptation of the input files to the proper format, and the window keep-out times, would allow for other analyses. Any operations task that uses the idea of keep-out windows will have a use for this program.

Khanampompan, Teerapat↗
DOE OSTI2021

Observation of Fundamental Mechanisms in Compression-Induced Phase Transformations Using Ultrafast X-ray Diffraction

As theoretically hypothesized for several decades in group IV transition metals, we have discovered a dynamically stabilized body-centered cubic (bcc) intermediate state in Zr under uniaxial loading at sub-nanosecond timescales. Under ultrafast shock wave compression, rather than the transformation from α-Zr to the more disordered hex-3 equilibrium ω-Zr phase, in its place we find the formation of a previously unobserved nonequilibrium bcc metastable intermediate. We probe the compression-induced phase transition pathway in zirconium using time-resolved sub-picosecond x-ray diffraction analysis at the Linac Coherent Light Source. We also present molecular dynamics simulations using a potential derived from first-principles methods which independently predict this intermediate phase under ultrafast shock conditions. In contrast with experiments on longer timescale (> 10 ns) where the phase diagram alone is an adequate predictor of the crystalline structure of a material, our recent study highlights the importance of metastability and time dependence in the kinetics of phase transformations.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Development of the Planar Inlet Design and Analysis Process (PINDAP)

The aerodynamic development of an engine inlet requires a comprehensive program of both wind tunnel testing and Computational Fluid Dynamics (CFD) simulations. To save time and resources, much "testing" is done using CFD before any design ever enters a wind tunnel. The focus of my project this summer is on CFD analysis tool development. In particular, I am working to further develop the capabilities of the Planar Inlet Design and Analysis Process (PINDAP). "PINDAP" is a collection of computational tools that allow for efficient and accurate design and analysis of the aerodynamics about and through inlets that can make use of a planar (two-dimensional or axisymmetric) geometric and flow assumption. PINDAP utilizes the WIND CFD flow solver, which is capable of simulating the turbulent, compressible flow field. My project this summer is a continuation of work that I performed for two previous summers. Two years ago, I used basic features of the PINDAP to design a Mach 5 hypersonic scramjet engine inlet and to demonstrate the feasibility of the PINDAP. The following summer, I worked to develop its geometry and grid generation capabilities to include subsonic and supersonic inlets, complete bodies and cowls, conic leading and trailing edges, as well as airfoils. These additions allowed for much more design flexibility when using the program.

Gruber, Christopher R.↗
NASA NTRS2016

Tethered Space Satellite-1 (TSS-1): Wound About a Bolt

In the early 1990's US and Italian scientists collaborated to study the electrodynamics on a long tether between two satellites as it moved through the electrically charged portion of Earth's atmosphere called the ionosphere. Potential uses for the electrical current induced in the long wire include power and thrust generation for a satellite, momentum exchange, artificial gravity, deployment of sensors or antennas, and gravity-gradient stabilization. The Tethered Space Satellite (TSS) was a first-of-its-kind experiment with long tethers in space. It consisted of a satellite with science experiments attached to a 12.5 mile long, very thin (0.10 inch diameter) copper wire assembly wound around a spool in the deployer reel mechanism. The whole mechanism sits on a pallet that is installed into the Shuttle bay. At an altitude of 160 nautical miles above earth, the satellite would be deplodeployed from the Shuttle bay by raising it on a boom facing away from Earth. Once cleared of the bay, the deployer mechanism would slowly feed out the 12-plus miles of tether. Scientific data would be collected throughout the operation, after which the satellite would be reeled back in. A receiver spool to catch the 12.5 mile tether as it was being unwound by the deployer reel mechanism was set up to do the system-level test of deployer real mechanism prior to installing the loaded pallet into the Shuttle bay. The system level tests were required before the pallet could be installed into the Space Shuttle cargo bay. A few months before flight, the system level tests, including unreeling and reeling the tether, were completed at Kennedy Space Center (KSC) and the TSS payload was installed onto the Spacelab pallet. Some of this testing equipment was then shipped back to the contractor, Martin Marietta. Integration with the Shuttle began. Systems-level load analyses, which cannot be run until all information about each payload is finalized, was run in parallel with the physical integration of the hardware into the Shuttle payload bay. An analysis, called Coupled loads analysis, incorporates any updates to the model due to system level tests of all the different payloads, and any changes that were found during integration. Engineering analysis examines the worst case scenarios for the loads the hardware will see. The two times during the mission where the dynamic loads are the worst were 1) the first 10-second portion of Shuttle lift off, and 2) a 2-second time during landing when the landing gears hit the ground. The coupled loads analysis using the final verification loads showed that a single bolt attaching the deployer reel mechanism to the support structure had a "negative margin" - which is an indication that it might fail - during touch down. Hardware certification rules do not allow for hardware to fly with negative margins. A structural failure of one payload could have serious or catastrophic consequences to other payloads, or may significantly damage the Orbiter. The issue had to be resolved before the flight.

O'Connor, Brian↗
DOE OSTI2020

Heterogeneous Polymer Dynamics Explored Using Static 1H NMR Spectra

NMR spectroscopy continues to provide important molecular level details of dynamics in different polymer materials, ranging from rubbers to highly crosslinked composites. It has been argued that thermoset polymers containing dynamic and chemical heterogeneities can be fully cured at temperatures well below the final glass transition temperature (Tg). In this paper, we described the use of static solid-state 1H NMR spectroscopy to measure the activation of different chain dynamics as a function of temperature. Near Tg, increasing polymer segmental chain fluctuations lead to dynamic averaging of the local homonuclear proton-proton (1H-1H) dipolar couplings, as reflected in the reduction of the NMR line shape second moment (M2) when motions are faster than the magnitude of the dipolar coupling. In general, for polymer systems, distributions in the dynamic correlation times are commonly expected. To help identify the limitations and pitfalls of M2 analyses, the impact of activation energy or, equivalently, correlation time distributions, on the analysis of 1H NMR M2 temperature variations is explored. It is shown by using normalized reference curves that the distributions in dynamic activation energies can be measured from the M2 temperature behavior. An example of the M2 analysis for a series of thermosetting polymers with systematically varied dynamic heterogeneity is presented and discussed.

36 MATERIALS SCIENCE↗