Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diesel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Demonstration of low-level biogenic fuel content using quench curve and direct liquid scintillation counting (LSC) methods

In this work, an investigation into the direct method for liquid scintillation counting (LSC) quantification of biogenic fuel content in fuel blendstock is presented. This method development intentionally used a colored matrix (~99 wt%), fossil diesel fraction, and low-level biogenic fractions (~1 wt%) to determine the applicability of the LSC technique in colored blend mixtures. LSC procedures for quench correction, including the use of an instrument internal standard (Quantulus SQP values), color quench curves, and an internal 14 C standard spike on samples containing low-level amounts of biogenic gasoline, jet, and diesel mixed with fossil fuel, were compared. Samples were analyzed on both Perkin-Elmer Quantulus and Tri-Carb instruments, and the 14 C contents were compared with those determined by accelerator mass spectrometry (AMS). Results from the Tri-Carb instrument showed that percent differences of <10 % compared to AMS-reported values are achievable at 5-hour count times despite colored samples. A comparison between the impact of chemical and color quenching in the fuel samples showed that color quenching in highly colored samples reduces efficiency significantly more than chemical quenching, indicating that chemical quench curves are not appropriate for highly colored biofuel/fossil-fuel blended samples. Results indicate that both the direct method with internal spike quench correction and the use of a color-quench curve provide accurate results for 1 % biogenic fuel blends. Additionally, we have explored the use of Fourier transform infrared (FTIR) spectroscopy in measuring the biogenic content of the colored blended fuel samples. Preliminary results show the presence of biogenic carbon-derived fingerprints that are absent in fossil-derived sample. However, further work is needed to develop an FTIR-based quantitative method.

09 BIOMASS FUELS↗
DOE OSTI2020

An energy model of droplet impingement on an inclined wall under isothermal and non-isothermal environments

The observation of spray-wall interaction is of great importance to understand the dynamics that occur during fuel impingement onto the chamber wall or piston surfaces in internal combustion engines. It is found that the maximum spreading length of an impinged droplet can provide a quantitative estimation of heat transfer and energy transformation for spray-wall interaction. Furthermore, it influences the air-fuel mixing and hydrocarbon and particle emissions at combusting conditions. In this paper, an analytical model of different droplet-wall impingement conditions is developed in terms of βm (dimensionless maximum spreading length, the ratio of maximum spreading length to initial droplet diameter) to understand the detailed impinging dynamic process. These conditions are grouped as: a single diesel droplet impinging on the wall with different inclined angles (α); cold wall - heated droplet and heated wall - cold droplet impingement when inclined angle of the wall is 0°, respectively. The analytical model is built up based on the energy conservation that considers kinetic energy, gravitation energy, and surface energy before impingement, as well as viscous dissipation, gravitation energy, adhesion energy, deformation energy, and heat energy after impingement. The experimental work of diesel droplet impinging on an inclined wall is performed at a certain range of the Weber number (We of 33 to 420) with various inclined angles (α of 0° to 45°), while for inclined angle is 0°, droplet and wall temperature are varied from 25°C to 150°C to study the effects of the inclined angle and temperature on the temporal evolution of the post-impingement characteristics (i.e. droplet spreading length, dynamic contact angle). The analytical model is validated and evaluated at the aforementioned experimental operating points. The validated model can be employed to predict maximum spreading length of the droplet impinged on the wall. It is further utilized to determine the transition from capillary regime to kinetic regime, then to viscous regime at different inclined angle of the wall.

42 ENGINEERING↗
DOE OSTI2022

Performance and cost of fuel cells for off-road heavy-duty vehicles

Hydrogen fuel cell-powered off-road vehicles can replace hydrocarbon-powered off-road vehicles to reduce carbon dioxide and criteria pollutant emissions in the agriculture, construction, and mining industries. Vehicle manufacturers and customers recognize health and environmental benefits of emissions reductions but are ultimately compelled by the total cost of ownership of their vehicles. In this study, we conduct a technoeconomic evaluation for three hallmark off-road vehicles, tractors, wheel loaders, and excavators, comparing vehicles with hydrogen fuel cell + battery hybrid powertrains to traditional diesel powertrains. Stakeholder-valued performance metrics include fuel cell engine power, engine durability, hydrogen consumption rate, hydrogen storage system volume, and energy-regenerative drivetrain efficiency. The total cost of ownership includes capital, operating and maintenance, fuel, and fuel storage costs. State-of-the-art fuel cell powered wheel loaders and excavators are currently cost competitive with diesel platforms. If targeted improvements to cost, performance, and durability improvements of fuel cell stacks and storage systems are achieved, fuel cell systems would be cost competitive for tractors and significantly lower total cost of ownership options for wheel loaders and excavators.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Microwave-assisted pyrolysis of liquid hydrocarbons using iron-based alumina catalysts obtained by solution combustion synthesis: The effect of synthesis parameters

The microwave-absorbing and catalytic properties of iron-based alumina (FeAl x O y ) materials have enabled their use as catalysts for the microwave-assisted generation of hydrogen and carbon via pyrolysis of hydrocarbons. Solution combustion synthesis (SCS) is a promising method to fabricate these materials, but the pyrolysis performance still needs to be improved. The present work investigated how altering the SCS parameters affects the pyrolysis of diesel fuel, gasoline, and crude oil. Two fuels (citric acid and glycine), four Fe:Al molar ratios, and two heating modes (hotplate and furnace) were tested. Fe/γ-Al 2 O 3 and Fe/β-SiC catalysts were prepared via incipient wetness impregnation for comparison. Among the three fossil fuels tested, diesel fuel yielded the highest amounts of H 2 and least amounts of CO x . The choice of fuel for the SCS process and the Fe/Al ratio strongly affected pyrolysis performance as they influence properties important for both catalysis and microwave absorption. The use of glycine resulted in catalysts that exhibited high H 2 yield and low CO 2 generation, which is explained by the revealed structural differences. The increase in the Fe:Al molar ratio accelerated microwave heating by adding more magnetic loss but also increased the amount of CO x . When the optimal SCS parameters were used, FeAl x O y catalysts outperformed Fe/γ-Al 2 O 3 and Fe/β-SiC. The high H 2 generation efficiency of the SCS catalysts is explained by their enhanced microwave-absorption properties. Scanning electron microscopy and energy dispersive X-ray spectroscopy revealed the formation of large-diameter CNTs via the tip-growth mechanism. The regeneration of SCS catalysts was demonstrated via the Boudouard reaction.

Carbon nanotubes↗
DOE OSTI2024

Evaluation of methods for characterizing the fine particulate matter emissions from aircraft and other diffusion flame combustion aerosol sources

The U. S. Environmental Protection Agency in collaboration with the U. S. Air Force Arnold Engineering Development Complex conducted the VAriable Response In Aircraft nvPM Testing (VARIAnT) 3 and 4 test campaigns to compare nvPM emissions measurements from a variety of diffusion flame combustion aerosol sources (DFCASs), including a Cummins diesel engine, a diesel powered generator, two gas turbine start carts, a J85-GE-5 turbojet engine burning multiple fuels, and a Mini-CAST soot generator. The VARIAnT research program has conducted four test campaigns to date with the VARIAnT 3 and 4 test campaigns focusing on BC mass instrument performance, use of gas turbine engine sources for BC mass instrument calibration, and the characterization of the aerosols produced from the combustion sources. Results from both campaigns revealed agreement of about 20% between the AVL Micro-Soot Sensor, the Cavity Attenuated Phase Shift (CAPS PMSSA) monitor and the thermal-optical reference method for elemental carbon (EC), independent of the calibration source used. For the Artium LII-300, the measured mass concentrations in VARIAnT3 fall within 18% and in VARIAnT4 fall within 32% of the reference EC mass concentration when calibrated on a combustor rig in VARIAnT3 and on a LGT-60 start cart in VARIAnT4, respectively. It was also found that the three mass instrument types (MSS, CAPS PMSSA, and LII-300) can exhibit different BC to reference EC ratios depending on the emission source that appear to correlate to particle geometric mean mobility diameter, morphology, or some other parameter associated with particle geometric mean diameter (GMD) with the LII-300 showing a slightly stronger apparent trend with GMD. Systematic differences in LII-300 measured mass concentrations have been reduced by calibrating with a turbine combustion source (combustor or turbine engine). With respect to the particle size measurements made, the sizing instruments (TSI SMPS, TSI EEPS, and Cambustion DMS 500) were found to be in general agreement in terms of size distributions and concentrations with some exceptions. Teflon filter measurements of the total aerosol mass produced by the various DFCASs differed from the reference EC, BC, and integrated particle sized distribution measured aerosol masses. The Teflon filter measured mass was 30 to 40% greater than the reference EC and 50 to 60% greater than the BC mass for the J85 in both test campaigns. The measurements of particle size distributions and single particle analysis by miniSPLAT indicated the presence of large particles (>100 nm) having more compact morphologies, higher effective density, and a composition dominated by OC and ash. This increased large particle fraction is also associated with higher values of single scattering albedo measured by the CAPS PMSSA instrument and higher OC/EC measurements. These measurements indicate gas turbine engine emissions can be a more heterogeneous mix of particle types beyond the original E31 assumption that it is mainly composed of black carbon.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Biomass feedstock transport using fuel cell and battery electric trucks improves lifecycle metrics of biofuel sustainability and economy

We report the use of new vehicle technologies such as fuel cell hybrid electric and fully electric powertrains for biomass feedstock supply is an unexplored solution to reducing biofuel production cost, greenhouse gas emissions, and health impacts. These technologies have found success in light-duty vehicle applications and are in development for heavy-duty trucks. This study presents the first detailed stochastic techno-economic analysis and life-cycle assessment of biomass feedstock supply systems with diesel, fuel cell hybrid electric, and fully electric trucks and determines their impacts on biofuel production considering butanol as a representative biofuel. This study finds that fuel cell hybrid electric and fully electric trucks consume less energy relative to the diesel-powered truck regardless of the evaluated circumstances, including payloads of truck (loaded and empty), pavement types (gravel and paved), road conditions (normal and damaged), and road networks (local and highways). The use of fuel cell hybrid and fully electric trucks powered by H 2 -fuel and renewable sources of electricity, respectively, results in a large reduction in cost and carbon footprint, specifically for a long-distance hauling, and minimize other economic and environmental impacts. While the economic advantage of fuel cell hybrid electric vehicle is dependent on the price of H 2 -fuel and road conditions, use reduces the GHG emissions of biobutanol per 100 km-trucking-distance by 0.98-10.9 gCO 2e /MJ. Results show that converting to fully electric truck transport decreases the biobutanol production cost and GHG emissions per 100 km-trucking-distance by 0.4-7.3 cents/L and 0.78 to 9.1 gCO 2e /MJ, respectively. This study establishes the foundation for future investigations that will guide the development of economically, socially, and environmentally sustainable biomass feedstock supply system for cellulosic biorefineries or other goods transportation systems.

09 BIOMASS FUELS↗
DOE OSTI2026

Drive Cycles, Battery Pack Scaling, and Usage Considerations for Long-Haul and Regional-Haul Electric Trucks

Electrifying Class-8 heavy-duty trucks presents a promising opportunity to enhance energy efficiency and reduce freight transport costs. Battery electric trucks (BETs), once considered niche, are gaining traction due to advancements in battery technology and cost reductions. However, accurately predicting battery lifespan under realistic usage conditions remains a key challenge. Understanding battery failure mechanisms and their links to design, operation, and management is essential for developers and fleet operators. This study introduces a method to develop simplified, lab-testable dynamic stress test (DST) cycles for regional and long-haul Class-8 BETs, derived from real-world diesel truck usage. These DSTs enable benchmarking of battery technologies, identification of aging stressors, and optimization of battery design, life, and cost. The approach supports evaluation of key metrics such as levelized cost of driving and total cost of ownership, aiding fair comparisons and adoption decisions. We also propose feasible battery pack sizes that meet current driving demands with strategic charging, and a method to scale pack-level DSTs to cell-level cycles for lab-based testing. These tools facilitate tradeoff analysis across battery chemistries, pack sizing, and charging strategies, while offering means to get insights into battery aging under realistic conditions-ultimately supporting informed BET deployment decisions.

25 ENERGY STORAGE↗
DOE OSTI2020

A comparison of computational models for predicting yield sooting index

Sooting propensity, a measurement of how much particulate matter is produced when a fuel is burned, is a property of significant interest among researchers who are striving to discover the next generation of cleaner, more efficient fuels and fuel additives. Many compounds are not viable as fuels and/or fuel additives, and as a result, designing cleaner-burning biofuels using only experimental techniques is inefficient. Predictive models have been instrumental in reducing this inherent difficulty, providing researchers with a tool to preemptively screen compounds before production and testing. The present work compares the accuracies and interpretabilities of existing models used to predict a particular measure of sooting propensity, Yield Sooting Index (YSI). These models include artificial neural networks, graph neural networks, and multivariate equations. A novel equation for predicting YSI based on atom path count and bond order is proposed, which can highlight key structural components that contribute to YSI. It was found that artificial neural networks slightly outperform graph neural networks and greatly outperform multivariate equations in blind (test set) prediction accuracy; however, graph neural networks and multivariate equations provide significantly more interpretability as to how compound structure relates to YSI. Predictions of YSI are compared to experimental measurements for previously un-tested compounds with cetane numbers comparable to diesel fuel (50-60) (butyl decanoate, ethyl decanoate, 1,4-bis(ethenoxymethyl)cyclohexane, and 5-heptyloxolan-2-one), and it was found that these compounds produce significantly less soot compared to diesel fuel.

09 BIOMASS FUELS↗
DOE OSTI2022

Influence of NOx chemistry on the prediction of natural gas end-gas autoignition in CFD engine simulations

Natural gas (NG) represents a promising low-cost/low-emission alternative to diesel fuel when used in high-efficiency internal combustion engines. Advanced combustion strategies utilizing high EGR rates and controlled end-gas autoignition can be implemented with NG to achieve diesel-like efficiencies; however, to support the design of these next-generation NG ICEs, computational tools, including single- and multi-dimensional simulation packages will need to account for the complex chemistry that can occur between the reactive species found in EGR (including NOx) and the fuel. Research has shown that NOx plays an important role in the promotion/inhibition of large hydrocarbon autoignition and when accounted for in CFD engine simulations, can significantly improve the prediction of end-gas autoignition for these fuels. However, reduced NOx-enabled NG mechanisms for use in CFD engine simulations are lacking, and as a result, the influence of NOx chemistry on NG engine operation remains unknown. Here, we analyze the effects of NOx chemistry on the prediction of NG/oxidizer/EGR autoignition and generate a reduced mechanism of a suitable size to be used in engine simulations. Results indicate that NG ignition is sensitive to NOx chemistry, where it was observed that the addition of EGR, which included NOx, promoted NG autoignition. The modified mechanism captured well all trends and closely matched experimentally measured ignition delay times for a wide range of EGR rates and NG compositions. Here, the importance of C2-C3 chemistry is noted, especially for wet NG compositions containing high fractions of ethane and propane. Finally, when utilized in CFD simulations of a Cooperative Fuels Research (CFR) engine, the new reduced mechanism was able to predict the knock onset crank angle (KOCA) to within one crank angle degree of experimental data, a significant improvement compared to previous simulations without NOx chemistry.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Understanding the ignition process and flame structure of conventional and oxygenated fuels under engine relevant conditions – An optical study

Renewably generated synthetic fuels such as poly-oxymethylene ethers (OME) have a significant potential to effectively break the soot-NOX trade-off in compression ignition engines by using exhaust gas recirculation (EGR) to maintain low nitrogen oxide (NOX) emissions while maintaining good efficiency and simultaneously contributing to circular carbon economy. However, owing to the fundamental differences in properties of OME when compared to fossil-based diesel fuels, it is critical to fully understand its ignition and combustion phenomenology to take advantage of this fuel to its utmost potential. In this context, this work outlines the results of a systematic experimental study performed in a heavy-duty, single-cylinder, optical engine probing the spatial and temporal progression of fuel decomposition and ignition behavior of OME when compared to n-dodecane, a diesel-fuel surrogate. Thermodynamic analysis and optical diagnostics techniques including simultaneous HCHO-PLIF and OH-PLIF complemented by high-speed OH* chemiluminescence were employed along with parametric sweeps of intake temperature and EGR dilution rates. OME does not exhibit any observable low temperature heat release irrespective of the ambient oxygen concentration. Differences in the observed diffusive flame structure such as longer flame lift-off length, less pronounced combustion recession, faster premixed burn at ignition (“volumetric” ignition), non-sooting behavior suggest that the inherent presence of fuel-bound oxygen in OME can skew the air-fuel ratio (AFR) distribution within the jet thereby reducing the reliance of combustion on mixing and air entrainment. This leads to rapid late-cycle oxidation leading to shorter combustion duration and favorable combustion phasing. Results also suggest that OME exhibits relatively weak negative temperature coefficient (NTC) behavior, however, the OME fuel-decomposition kinetic-pathways produce significant concentration of HCHO, which might be erroneously interpreted as a product of cool-flames.

Air-fuel ratio↗
DOE OSTI2022

Looking Beyond Bill Savings to Equity in Renewable Energy Microgrid Deployment

Microgrids powered by renewable energy can provide backup power to critical infrastructure during grid outages. These systems can also play an important role in advancing energy justice by providing economic, environmental, health, and resilience benefits for underserved communities. The value of microgrids is often measured by the economic savings and resilience provided, but there are other energy justice factors that should be considered. This paper describes a methodology for quantifying broader costs and benefits including utility bill savings, value of resilience, social cost of carbon, public health costs, and jobs associated with the construction and operation of microgrids. We evaluate these factors at three case study sites and find that including energy justice values in the cost-benefit analysis of microgrids can change investment decisions. When climate, health, resilience, and job creation are considered, cost-optimal microgrids include more renewable generation, leading to a 52-82% reduction in emissions and diesel fuel use. The net present values of the microgrids grow from negative $626,000-843,000 in the diesel only case to $10-16 million in the hybrid microgrid case and $12-19 million in the renewable microgrid case, indicating potential for greater microgrid deployment if energy justice values are incorporated in decision making. However, we also see large increases in capital expenses, which could limit deployment unless accompanied by innovative financing measures. These findings may be useful to communities as they seek to strengthen resilience to natural disasters while also improving public health, meeting climate goals, and providing economic opportunity for residents.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Combined Land Use of Solar Infrastructure and Agriculture for Socioeconomic and Environmental Co-Benefits in the Tropics

Solar photovoltaics (PV) are on the rise even in areas of low solar insolation. However, in developing countries with limited capital, land scarcity, or with geographically isolated agrarian communities, large solar infrastructures are often impractical. In these cases, implementation of low-density PV over existing crops may be required to integrate renewable energy services into rural communities. Here, using Indonesia as a model system, we investigated the land use, energy, greenhouse gas emissions, economic feasibility, and the environmental co-benefits associated with off-grid solar PV when combined with high value crop cultivation. The life cycle analyses indicate that small-scale dual land-use systems are economically viable in certain configurations and have the potential to provide several co-benefits including rural electrification, retrofitting diesel electricity generation, and electricity for processing agricultural products locally. A hypothetical full-density off-grid solar PV for a model village in Indonesia shows that electricity output (1907.5 GJ yr-1) is much higher than the total residential consumption (678 GJ yr-1), highlighting the opportunity to downscale the PV infrastructure by half to lower capital cost, to co-locate crops, and to support secondary income generating activities. Economic analysis shows that the 30-year net present cost of electricity from the half-density co-located PV system (12,257 million IDR) is significantly lower than that of the flat cost of diesel required to generate equivalent electricity (14,702 million IDR). Our analysis provides insights for smarter energy planning by optimizing the efficiency of land use and limiting conversion of agricultural and forested areas for energy production.

agrivoltaics↗
DOE OSTI2022

Carbon footprint prediction considering the evolution of alternative fuels and cargo: A case study of Yangtze river ships

For reducing carbon emissions in the shipping sector, application of alternative low-carbon and zero-carbon fuels is the consensus. However, requirements of economic development cannot be ignored while focusing on emission reduction. Cargo development is an important prerequisite. Considering the cargo growth as a novelty, a method to calculate the annual carbon emissions of different alternative fuel-powered ships in different cargo growth prospects and power scenarios is proposed. With respect to the time dimension, the relationship between alternative fuels, cargo, and carbon reduction is revealed. The Yangtze River bulk carrier case was studied and the life cycle carbon emission analysis of diesel, LNG hybrid, LNG, hydrogen, methanol, and ammonia were carried out. The annual carbon curves of the high, steady, and low cargo growth prospects were obtained for different scenarios of the power system structure. The results show that LNG hybrid, LNG and methanol fuels are currently the suitable choices. Their life cycle carbon emissions were reduced by 31.5–38.1% compared with those of diesel power. The carbon emissions of green hydrogen and green ammonia were reduced by 78.8% and 91.3%, respectively, compared with those of hydrogen and ammonia. The carbon reduction results of green fuels in their initial application were explored which are at 0.6–10.8%. In addition, there is a balanced annual growth rate, whose annual carbon curve will be steady under its corresponding scenario of power system structure, which could help the ship owners plan their future.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Characterization of commercial vehicles’ start-up operations from in-use data

Diesel engines produce disproportionate levels of emissions when the engine and after-treatment systems are operating at low temperatures. This situation arises most commonly when the vehicle is first started after overnight. To quantify emissions attributable to vehicle starts, a sizable collection of on-road commercial vehicle operating data is analyzed to identify start-up events and inspect associated emissions. Data was obtained from the National Renewable Energy Laboratory’s (NREL’s) Fleet DNA and from the Center for Environmental Research & Technology (CE-CERT). Included are 500 + diesel vehicles with more than 42,000 recorded days, drawn from 25 vocational categories across the United States. Analysis shows that vehicle behavior, in terms of engine cold- and warm-operation, starts per day, soak time, and warm-up duration, differs significantly between vehicle vocations. Also, weighting factors for cold- and hot-starts currently used in the U.S. Environmental Protection Agency’s Federal Test Procedure (FTP) for heavy-duty emissions certification accurately represent real-world operations. Although the FTP includes a comparable fraction of cold operation, the hot fraction is much shorter than real-world operation due to limited test duration. The investigation also revealed that real-world engines operate for a significant amount of time when the engine coolant is in the “hot-stabilized” region, but the selective catalytic reduction (SCR) temperature is below its effective operating temperature of 200 °C. Of the vehicles under investigation, almost 20% of their operational time is within this condition. Therefore, novel approaches to raise and maintain SCR temperature are highly required to further reduce engine emissions.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Compatibility of Fuel System Elastomers and Plastics with a Fast-Pyrolysis Oil (Bio-oil) at Room Temperature

Herein the compatibility of a fast-pyrolysis bio-oil with 17 elastomer and 21 plastic materials common to fuel storage, dispensing, and delivery systems was assessed by measuring volume and hardness. Diesel was used as the baseline for comparison. The elastomer and plastic specimens were exposed to the test fuels at 23 °C. The exposure times were 4 and 16 weeks for the elastomers and plastics, respectively. The elastomers (except for silicone and styrene butadiene) exhibited pronounced swelling in the bio-oil. This was especially true for the fluorocarbons and acrylonitrile rubbers. For the elastomers, a strong correlation between polarity and volume swell was observed. Compositional and structural analysis on one of the fluorocarbon materials showed that the bio-oil was less effective at extracting phthalate additives than the diesel. However, the crystallinity of a fluorocarbon was altered by the bio-oil. Unlike the elastomers, the plastic materials were less impacted by exposure to the bio-oil. This finding is attributed to their denser and more rigid molecular structures (compared to the elastomers). Notable swelling did occur in the nylons, but this swelling was attributed to water absorption rather than polarity. Comparison with previous studies showed that the observed swelling was lower for both the elastomers and the plastics. Solubility (and hence swell) increases with temperature, and because this study was conducted at 23 °C rather than 50 °C, the reduced temperature is responsible for the lower swell levels.

09 BIOMASS FUELS↗
DOE OSTI2023

Co-Hydrotreatment of Yellow Greases and the Water-Insoluble Fraction of Pyrolysis Oil. Part I: Experimental Design to Increase Kerosene Yield and Reduce Coke Formation

Here, this paper reports the co-hydrotreatment of Biomass Technology Group commercial pyrolysis oil water-insoluble (WIS) phase (also known as pyrolytic lignin) and yellow greases (waste cooking oil), aiming to produce sustainable aviation fuels (SAFs). We use a sulfided NiMo/Al 2 O 3 blend with 16 wt % WIS and a central composite experimental design to identify processing conditions increasing kerosene yield and reducing coke formation. The input variables were: (1) reaction temperature (320, 350, and 380 °C), (2) initial hydrogen pressure (5, 6, and 7 MPa), and (3) amount of catalyst (0.7, 1.0, and 1.3 g). The hydrotreated oily phases were distilled to obtain gasoline (<150 °C), kerosene (150–250 °C), diesel (250–350 °C), and residual oil (>350 °C). The reaction temperature is the main factor affecting the yield of gaseous, solid, and liquid products. Meanwhile, a higher initial hydrogen pressure and catalyst loading increased the yield of kerosene and other distillates and decreased the coke formation. A high temperature correlated with a lower content of oxygenates in kerosene cuts. Based on our experimental results, we propose to conduct hydrotreatment studies at 380 °C, initial H 2 pressure of 7 MPa, and 1.3 g of catalyst. Under the identified conditions, it was possible to improve the kerosene yield to more than 20 wt % and reduce the yield of coke to close to 2.0 wt %. The chemical composition and fuel properties of the gasoline, kerosene, and diesel cuts were thoroughly analyzed. The content of aromatics and phenols in the kerosene fraction produced at the conditions identified in this project exceeded the recommended values for SAFs. New strategies (such as blending and more intense hydrotreatment to remove oxygenated compounds) need to be implemented to reduce the content of these molecules in our final product.

09 BIOMASS FUELS↗
DOE OSTI2024

Co-hydrotreatment of Bio-oil and Waste Cooking Oil to Produce Transportation Fuels

This paper reports the co-hydrotreatment of the heavy bio-oil fraction with waste cooking oil (WCO) using NiMo/γ-Al 2 O 3 catalyst, followed by the distillation of resulting deoxygenated oil and the characterization of resulting fuel cuts. The heavy BTG bio-oil fraction was obtained by removing the very reactive light-oxygenated compounds via rotary evaporation, subsequently mixed with 1-butanol. The resulting oil was blended with WCO and subjected to a two-step co-hydrotreatment process. The first step, called “stabilization,” is aimed at saturating highly reactive hydrogen-deficient compounds. The second step, called “deoxygenation,” aimed to remove bio-oil oxygen, primarily as H 2 O. This study examined the impact of varying bio-oil concentrations (0, 10, 20, 30, 40 wt.% of WCO) on the upgraded oil's yield, composition, and fuel properties. The resulting hydrotreated oil was distilled into gasoline-range, kerosene-range, and diesel-range hydrocarbons at <150 °C, 150 to 250 °C, and 250 to 350 °C, respectively. The yield of the hydrotreated oil indicates that as the bio-oil concentration increases, the amounts of coke (0.7 to 2.4 %) and water (2 to 10 wt. %) increase while the organic layer yields decrease (80 to 63 %). The coke yield was comparable to the coke yield obtained when co-processing the pyrolytic lignin fraction. This suggests that coke is formed from both the sugar oligomers and the lignin-derived oligomers. The UV-fluorescence analysis on the hydrotreated oil shows that more polycondensed and conjugated ring compounds formed as the bio-oil concentration is increased. These compounds are precursors of coke. FTIR results showed that most raw materials were converted to biofuels after the hydrotreatment. To achieve less than 1 wt. % of coke yield, blends with up to 20 wt. % pyrolysis oil should be used. An increase in bio-oil concentration leads to a slight increase in gasoline yield and a decrease in kerosene and diesel yields. The identified carbon species found in the fuel cuts include n-paraffin, iso-paraffin, cycloparaffin, and aromatics. Further, the jet fuel cut (kerosene) was characterized by density, surface tension, and viscosity. Our product conforms to the standard specifications for sustainable aviation fuels (Jet A-1). Further research is suggested to fine-tune the operating parameters for achieving reduced coke yield and enhanced kerosene yield.

09 BIOMASS FUELS↗
DOE OSTI2022

Regionalized Life-Cycle Water Impacts of Microalgal-Based Biofuels in the United States

While algal biofuels have the potential to reduce the national reliance on fossil fuels, high water consumption associated with algal biomass cultivation represents a major concern potentially compromising the sustainable commercialization of this technology. This study focuses on quantifying the water footprint (WF) and water scarcity footprint (WSF) of renewable diesel derived from algal biomass and provides insights into where algal cultivation is less water-intensive than traditional ethanol and biodiesel feedstocks. Results are generated with an engineering process model developed to predict the life-cycle water consumption, considering green, blue, and gray water, of algae facilities across the United States at a high spatiotemporal resolution. The total WFs for Florida and Arizona are determined to be 13.1 and 17.6 m 3 GJ –1 , respectively. The blue WF in Arizona is shown to be 8.5 times larger than in Florida, while the green WF is 4.5 times smaller, but when combined into a total WF, there is just a 26% difference between the two locations. The analysis reveals that the total life-cycle WFs of algal renewable diesel are smaller than the optimal WFs of corn ethanol and soybean biodiesel. Algal systems benefit from higher growth rates and offer the opportunity to manage wastewater streams, therefore generating smaller green and gray WFs than those of conventional biofuels. Here, the WSF analysis identifies the Gulf Coast as the most suitable region for algal cultivation, with cultivation in the western US shown to exacerbate local water stress levels.

54 ENVIRONMENTAL SCIENCES↗