Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Curves”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1922

Effect of aerofoil aspect ratio on the slope of the lift curve

On of the most important characteristics of an airfoil is the rate of change of lift with angle of attack, (sup dC)L/d alpha. This factor determines the effectiveness of a tail plane in securing static longitudinal stability. The application of the Gottingen formulas given here for calculating the variation of (sup Dc)L/d alpha with aspect ratio should be of interest to many aeronautical engineers. For the convenience of the engineer, a set of curves calculated by the method set forth here are given in graphical form. Also, the observed values of (sup dC)L/d alpha for the same airfoil at various aspect ratios follow the calculated curves closely.

Diehl, Walter S↗
NASA NTRS1930

Strength in Shear of the Thin Curved Sheets of Alclad

This note is on an investigation made to obtain information on the strength of thin curved sheets of Alclad in shear. Designers may utilize this material as a strength member as well as for a covering for the wings and fuselages. A reduction may then be made in the size of the internal strength members. These experiments were undertaken with the object of securing the maximum value from the metal in this respect. The point at which buckling occurs is of primary importance. The buckling shear of a curved thin plate was determined mathematically and also experimentally. The following formula was obtained mathematically: s=K E t/r in which s is the unit shear, K is a constant, E is the modulus of elasticity, t is the thickness of the material, and r is the radius of curvature. The value of K as determined by the experiments was found to be .075. This formula applies only when s is within the elastic limit of the material. The breaking point of the material was obtained in most of the tests as a matter of information and the results are included in this report. The effect of the supporting ribs was determined by varying the number used.

Smith, George Michael↗
NASA NTRS1957

Handbook of structural stability part III : buckling of curved plates and shells

Available theories and test data on buckling of curved plates and shells are reviewed. For torsion and external-pressure loadings, the test data are correlated in terms of linear buckling theories for both the elastic and inelastic ranges. The cases which exhibit a marked disagreement between linear theory and test data include those of curved plates and cylinders under axial compression, cylinders under bending, and spherical plates under external pressure. These cases have been analyzed by a unified semiempirical approach for both the elastic and inelastic ranges which is satisfactory for analysis and design purposes. The effects of internal pressure on buckling of elements under uniaxial loads are discussed and data on various combined loadings are presented in interaction form. (author)

Gerard, George↗
NASA NTRS1958

Handbook of structural stability part VI : strength of stiffened curved plates and shells

A comprehensive review of failure of stiffened curved plates and shells is presented. Panel instability in stiffened curved plates and general instability of stiffened cylinders are discussed. The loadings considered for the plates are axial, shear, and the combination of the two. For the cylinders, bending, external pressure, torsion, transverse shear, and combinations of these loads are considered. When possible, test data and theory were correlated. General instability in stiffened cylinders was investigated. For bending and torsion loads, test data and theory were correlated. For external pressure several existing theories were compared. As a result of this investigation a unified theoretical approach to analysis of general instability in stiffened cylinders was developed. (author)

Becker, Herbert↗
NASA NTRS1938

The Effective Width of Curved Sheet After Buckling

This report describes experiments made for the purpose of ascertaining the effective width of circularly curved sheet under pure flexural stress. A relation for the effective width of curved sheets is established. Experiments were made with circular cylinders compressed in longitudinal direction. The sheets were rigidly built in at the sides parallel to the axis of the cylinder.

Wenzek, W A↗
NASA NTRS1937

Method of curved models and its application to the study of curvilinear flight of airships. Part I

In the first part of this paper we shall present the theoretical side of the problem of constructing curved model forms and the method of testing the model. In the second part we shall present a detailed account of the first experiments according to the given method, carried out with a curved model of the nonrigid airship V-2, and a comparison of the experimental results with some data of full-scale tests made with this airship in 1933.

Gourjienko, G A↗
NASA NTRS1993

Radio light curves of V471 Tauri

We have acquired light curves at a wavelength of 6 cm of the eclipsing binary V471 Tauri around the orbit, in order to determine the geometrical location of the radio emission in the binary. Each light curve shows a broad minimum near the time of optical eclipse, suggesting that the radio luminosity originates between the two stars. Other observations at X-ray, UV, and visual wavelengths are also supportive of the idea of a gas cloud more or less permanently located between the stars. This could be explained if the radio emission arises from the interaction of the magnetic fields of the secondary and the white dwarf near the line of centers.

Patterson, Joseph↗
NASA NTRS1994

A Study of Dean Vortex Development and Structure in a Curved Rectangular Channel with Aspect Ratio of 40 at Dean Numbers up to 430

Flow in a curved channel with mild curvature, an aspect ratio of 40 to 1, and an inner to outer radius ratio of 0.979 is studied at Dean numbers De ranging from 35 to 430. For positions from the start of curvature ranging from 85 to 145 degrees, the sequence of transition events begins with curved channel Poiseuille flow at De less than 40-64. As the Dean number increases, observations show initial development of Dean vortex pairs, followed by symmetric vortex pairs which, when viewed in spanwise/radial planes, cover the entire channel height (De=90-100). At De from 40 to 125-130, the vortex pairs often develop intermittent waviness in the form of vortex undulations. Splitting and merging of vortex pairs is also observed over the same experimental conditions as well as at higher De. When Dean numbers range from 130 to 185-200, the undulating wavy mode is replaced by a twisting mode with higher amplitudes of oscillation and shorter wavelengths. The twisting wavy mode results in the development of regions where turbulence intensity is locally augmented at Dean numbers from 150 to 185-200, principally in the upwash regions between the two individual vortices which make up each vortex pair. These turbulent regions eventually increase in intensity and spatial extent as the Dean number increases further, until individual regions merge together so that the entire cross section of the channel contains chaotic turbulent motions. When Dean numbers then reach 400-435, spectra of velocity fluctuations then evidence fully turbulent flow.

Ligrani, Phillip M.↗
NASA NTRS1994

On the evolution of centrifugal instabilities within curved incompressible mixing layers

It is known that certain configurations which possess curvature are prone to a class of instabilities which their 'flat' counterparts will not support. The main thrust of the study of these centrifugal instabilities has concentrated on curved solid boundaries and their effect on the fluid motion. In this article attention is shifted towards a fluid-fluid interface observed within a curved incompressible mixing layer. Experimental evidence is available to support the conjecture that this situation may be subjected to centrifugal instabilities. The evolution of modes with wavelengths comparable with the layer's thickness is considered and the high Taylor/Gortler number regime is also discussed which characterizes the ultimate fate of the modes.

Otto, S. R.↗
NASA NTRS1994

Multi-lab comparison on R-curve methodologies: Alloy 2024-T3

In an effort to determine an optimum method for ranking the fracture toughness of developmental aluminum alloys for High Speed Civil Transport applications, five labs performed K and/or J based fracture tests on aluminum alloy 2024-T3. Two material thicknesses were examined: 0.063 in. and 0.125 in. Middle crack tension and compact tension specimens were excised from 60 in. wide middle crack tension panels which had been previously tested at Boeing. The crack resistance curves generated were compared to the R-curves from 60 in. wide specimens. The experimental program indicated that effective stress intensity from secant compliance based crack length and stress intensity calculated from J-integral testing were equivalent. In addition, comparison of different specimen sizes and configurations indicated that standard validity requirements for compact tension specimens may be overly restrictive.

Reynolds, Anthony P.↗
NASA NTRS1994

Prediction of R-curves from small coupon tests

R-curves were predicted for Alclad 2024-T3 and C188-T3 sheet using the results of small-coupon Kahn tear tests in combination with two-dimensional elastic-plastic finite element stress analyses. The predictions were compared to experimental R-curves from 6.3, 16 and 60-inch wide M(T) specimens and good agreement was obtained. The method is an inexpensive alternative to wide panel testing for characterizing the fracture toughness of damage-tolerant sheet alloys. The usefulness of this approach was demonstrated by performing residual strength calculations for a two-bay crack in a representative fuselage structure. C188-T3 was predicted to have a 24 percent higher load carrying capability than 2024-T3 in this application as a result of its superior fracture toughness.

Yeh, J. R.↗
NASA NTRS1995

Wavenumber selection for small-wavelength Goertler vortices in curved channel flows

The problem of wavenumber selection for fully nonlinear, small-wavelength Goertler vortices in a curved channel flow is considered. These types of Goertler vortices were first considered by Hall & Lakin (1988) for an external boundary layer flow. They proved particularly amenable to asymptotic description, it was possible to consider vortices large enough so that the mean flow correction driven by them is as large as the basic state, and this prompted the authors to consider them in a curved channel flow as an initial application of the phase-equation approach to Goertler vortices. This involves the assumption that the phase variable of these Goertler vortices varies on slow spanwise and time scales, then an analysis of both inside and outside the core region, to which vortex activity is restricted, leads to a system of partial differential equations which can be solved numerically for the wavenumber. The authors consider in particular the effect on the wavenumber of the outer channel wall varying on the same slow spanwise scale as the phase variable.

Dando, Andrew↗
NASA NTRS1992

The effect of material heterogeneity in curved composite beams for use in aircraft structures

A design tool is presented for predicting the effect of material heterogeneity on the performance of curved composite beams for use in aircraft fuselage structures. Material heterogeneity can be induced during processes such as sheet forming and stretch forming of thermoplastic composites. This heterogeneity can be introduced in the form of fiber realignment and spreading during the manufacturing process causing a gradient in material properties in both the radial and tangential directions. The analysis procedure uses a separate two-dimensional elasticity solution for the stresses in the flanges and web sections of the beam. The separate solutions are coupled by requiring the forces and displacements match at the section boundaries. Analysis is performed for curved beams loaded in pure bending and uniform pressure. The beams can be of any general cross-section such as a hat, T-, I-, or J-beam. Preliminary results show that geometry of the beam dictates the effect of heterogeneity on performance. Heterogeneity plays a much larger role in beams with a small average radius to depth ratio, R/t, where R is the average radius of the beam and t is the difference between the inside and outside radius. Results of the analysis are in the form of stresses and displacements, and they are compared to both mechanics of materials and numerical solutions obtained using finite element analysis.

Otoole, Brendan J.↗
NASA NTRS1994

An analytical and experimental investigation of the response of the curved, composite frame/skin specimens

Six-foot diameter, semicircular graphite/epoxy specimens representative of generic aircraft frames were loaded quasi-statistically to determine their load response and failure mechanisms for large deflections that occur in airplanes crashes. These frame/skin specimens consisted of a cylindrical skin section co-cured with a semicircular I-frame. The skin provided the necessary lateral stiffness to keep deformations in the plane of the frame in order to realistically represent deformations as they occur in actual fuselage structures. Various frame laminate stacking sequences and geometries were evaluated by statically loading the specimen until multiple failures occurred. Two analytical methods were compared for modeling the frame/skin specimens: a two-dimensional shell finite element analysis and a one-dimensional, closed-form, curved beam solution derived using an energy method. Flange effectivities were included in the beam analysis to account for the curling phenomenon that occurs in thin flanges of curved beams. Good correlation was obtained between experimental results and the analytical predictions of the linear response of the frames prior to the initial failure. The specimens were found to be useful for evaluating composite frame designs.

Moas, Eduardo↗
NASA NTRS1994

Very-broadband-structure and the linear rise in the extinction curve

Measurements of the very broadband structure in the visual part of the extinction curve are compared to IUE extinction curve parameters in the scheme of Fitzpatrick and Massa. The correlation of Very-broadband-structure (VBS) depth with FUV rise found by Reimann & Friedemann (1991) is shown to be a correlation with linear rise and not with far UV non-linear rise. The correlation with linear rise suggests that the VBS is due to an onset of extinction at about 1.8/micrometer, rather than what has previously been suggested: due to luminescence or the presence of two extinction components longward and shortward of the VBS. The optical properties inferred for the linear rise carrier are consistent with some amorphous solid with a large optical gap. Small carbonaceous grains may be the carrier of the linear rise in extinction, because the erosion of core-mantle particles is expected to produce many of such small grains and offers a natural mechanism for the existence of the inferred two populations of big (a approximately 0.13 micrometer) and small (a approximately 0.005 micrometer) grains.

Jenniskens, P.↗
NASA NTRS1995

The orbital light curve of PSR 1957 + 20

We make a detailed study of the optical light curve of PSR 1957 + 20. We show that the deep, smooth, and symmetrical modulation can be successfully modeled by a higl irradiated secondary. Two types of models are consistent with the data: (! a secodary close to filling its Rochhe lobe with 10%-20% of the incident flux converted to optical emission, and (2) a secondary considerably underfilling its Roche lobe, with a high degree of beaming of the neutron star flux. owever, the second model canbe rejected on the basis of current estimates of the extinction toward 1957 + 20. The proximity of the photosphere of the secondary to its Roche lobe facilitates mass loss by irradiation. Our ignorance of the (nonirradiated) luminosity of the secondary allows us to place only weak constraints on the inclination -50-80 deg. There is no evidence in the light curve for optical emission from any source in PSR 1957 + 20 other than the secondary itself.

Callanan, Paul J.↗
NASA NTRS1995

Extreme ultraviolet light curves of UZ Fornacis: Evidence for accretion stream absorption and vertical extent of the accretion spot

We report on two pointed observations of UZ For carried out by the imaging photometers aboard the Extreme Ultraviolet Explorer (EUVE), one as part of the EUVE Right Angle Program and one as an off-axis source during a guest observation. Both observations lasted approximately 3 days and covered a total of 72 orbits of the UZ For binary providing multiple coverage of all the orbital phases of UZ For. The resulting high signal-to-noise phase-folded light curve strongly constrains the emission and absorption geometry of UZ For. We have detected a narrow absorption dip that we attribute to the accretion stream at the location of the stagnation region many white dwarf radii away from the accretion spot and have also detected a broad dip caused by absorption much closer to the white dwarf surface. Both absorption effects are variable in time and phase. Based on the timescales of M-star eclipse ingress and egress, the angular spot size is constrained to be less than 5 deg; thus the ratio of spot area to white dwarf surface area is less than or equal to 0.0005. To explain the light curve phase duration given this small angular spot size, the extreme-ultraviolet (EUV) accretion spot must be raised vertically by approximately 5% of the white dwarf radius.

Warren, John K.↗