Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Corrosion Resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Superhydrophobic Post Treatment and Coating Extenders for Improved Asset Sustainability

Launch structures, hardware, and ground support equipment, at NASA's John F. Kennedy Space Center in Florida, are exposed to a highly corrosive natural coastal marine environment. In addition, during launches, rocket exhaust deposition is also highly corrosive. Superhydrophobic coatings are being considered for additional corrosion protection on existing structures to enhance corrosion resistance and add an additional layer of protection against harsh environmental elements. These coatings have come into their own recently, and are now being investigated as corrosion protective coatings due to their water repelling capability. These coatings can be used on existing coatings, newly coated materials, or used on bare substrates. The coatings are not suitable for permanent corrosion protection, but can be used where additional corrosion control is desired or only when temporary corrosion control is needed, such as in hardware sitting on a launch pad for 30-45 days prior to a launch. In this study, superhydrophobic coatings were applied on various coated and uncoated substrates and exposed to the spaceport environment for various times up to 60 days. This paper highlights the current results of the superhydrophobic coatings performance evaluated by X-ray photoelectron spectroscopy, and contact angle measurements.

Coating↗
DOE OSTI2021

Evaluation of Corrosion Susceptibility of Structural Steels in Biomass Derived Pyrolysis Oil

Biomass derived pyrolysis oil is a promising renewable energy source. Due to the variety of biomass feedstocks, the bio-oils could contain a wide range of organic constituents which would provide unique corrosive environments for structural materials. A preliminary work exposed different classes of steels and stainless steels to selected organic constituents of biomass pyrolysis oils and found that corrosion susceptibility, assessed using electrochemical impedance spectroscopy (EIS), was prominent in the steels with Cr lower than 11 wt.%. Although this result suggests stainless steels will resist corrosion by certain organic constituents, it may not be sufficient to predict the corrosion performance in real bio-oils. Therefore, this study attempted electrochemical measurements on Cr-alloyed steels and stainless steels directly exposed to a biomass derived pyrolysis oil. To overcome the low conductivity of bio-oils, a customized Luggin capillary was designed to minimize the ohmic path in bio-oils. The results of this work will be reported.

Jun, Jiheon↗
NASA NTRS1977

Laser shocking of 2024 and 7075 aluminum alloys

The effect of laser generated stress waves on the microstructure, hardness, strength and stress corrosion resistance of 2024 and 7075 aluminum alloys was investigated. Pulsed CO2 and neodymium-glass lasers were used to determine the effect of wavelength and pulse duration on pressure generation and material property changes. No changes in material properties were observed with CO2 laser. The strength and hardness of 2024-T351 and the strength of 7075-T73 aluminum alloys were substantially improved by the stress wave environments generated with the neodymium-glass laser. The mechanical properties of 2024-T851 and 7075-T651 were unchanged by the laser treatment. The correlation of the laser shock data with published results of flyer plate experiments demonstrated that a threshold pressure needed to be exceeded before strengthening and hardening could occur. Peak pressures generated by the pulsed laser source were less than 7.0 GPa which was below the threshold pressure required to change the mechanical properties of 2024-T851 and 7075-T651. Corrosion studies indicated that laser shocking increased the resistance to local attack in 2024-T351 and 7075-T651.

Clauer, A. H.↗
DOE OSTI2023

Tailoring the γ-γ'-γ" dual superlattice microstructure of INCONEL® 725 by high temperature aging and Nb/Ta additions for superior creep properties

Next-generation energy systems require superior resistance to creep deformation due to the considerably prolonged exposure times at operating stress and temperature. To improve the elevated temperature properties of INCONEL® 725 (IN725), a corrosion resistant alloy, several variants with different Ti/Al ratio and judicious amounts of Nb and Ta were made. Furthermore, a high temperature aging (HTA) heat treatment, designed to promote favorable precipitate phase formation, was explored. These adjustments allowed to tailor the amount and type of precipitate strengthening which led to significant increases in time to failure. The Ti/Al ratio was used to favor the formation of γ' or γ" precipitates. Compact morphology precipitates, consisting of γ' precipitates surrounded by a γ" shell, were formed in alloys with a low Ti/Al ratio. The HTA increased the creep life of various alloy formulations up to a maximum improvement of 371% as compared to the standard aging heat treatment. The Nb and Ta additions had a similar effect on increasing creep life by promoting and stabilizing γ" precipitation. The positive effect of the additions was even more pronounced when coupled with the HTA. A phase stability study with up to 10,000 h exposure at 700°C revealed that the compact morphology helped in slightly reducing coarsening of the γ' precipitates, although the effect on creep was not significant. The findings of this study enable design of dual superlattice alloys through microstructural engineering that yields superior performance and can be applied to a wide range of alloys in the IN718 and derivatives family.

Antonov, Stoichko↗
DOE OSTI2020

A comparative study on the physicochemical characteristics of nanoparticles released in vivo from CoCrMo tapers and cement–stem interfaces of total hip replacements

The good biocompatibility and corrosion resistance of the bulk CoCrMo alloy has resulted in it being used in the manufacture of implants and load bearing medical devices. These devices, however, can release wear and corrosion products which differ from the composition of the bulk CoCrMo alloy. The physicochemical characteristics of the particles and the associated in vivo reactivity are dictated by the wear mechanisms and electrochemical conditions at the sites of material loss. Debris released from CoCrMo hip bearings, taper junctions, or cement–stem interfaces can, therefore, have different chemical and morphological characteristics, which provide them with different in vivo toxicities. Here, we propose to assess and compare the characteristics of the particles released in vivo from CoCrMo tapers and cement–stem interfaces which have received less attention compared to debris originating from the hip bearings. The study uses state–of–art characterization techniques to provide a detailed understanding of the size, morphology, composition, and chemistry of the particles liberated from the wear and corrosion flakes from revised hip replacements, with an enzymatic treatment. The phase analyses identified Cr 2 O 3 nanoparticles released from tapers and cement–stem interfaces, whose composition did not vary with origin or particle morphology. The size distributions showed significantly smaller particles were released from the stems, compared to the particles originating from the corresponding tapers. Furthermore, the investigation demonstrates that the tribocorrosive processes occurring at the taper and stem interfaces both result in Cr 2 O 3 nanoparticle formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Aluminized alloy boosts turbine blade life

Description of an aluminized alloy coating technique that involves first the application of a ductile, oxidation-resistant overlay, such as NiCrAl, which is then partially aluminized. The duplex protective system has performance advantages over conventional aluminide coatings in that it provides higher-temperature hot corrosion resistance over a longer service life.

Gedwill, M. A.↗
NASA NTRS1986

Oxidation-resistant reflective surfaces for solar dynamic power generation in near Earth orbit

Reflective surfaces for space station power generation systems are required to withstand the atomic oxygen-dominated environment of near Earth orbit. Thin films of platinum and rhodium, which are corrosion resistant reflective metals, have been deposited by ion beam sputter deposition onto various substrate materials. Solar reflectances were then measured as a function of time of exposure to a RF-generated air plasma. Similarly, various protective coating materials, including MgF2, SiO2, Al2O3, and Si3N4, were deposited onto silver-coated substrates and then exposed to the plasma. Analysis of the films both before and after exposure by both ESCA and Auger spectroscopy was also performed. The results indicate that Pt and Rh do not suffer any loss in reflectance over the duration of the tests. Also, each of the coating materials survived the plasma environment. The ESCA and Auger analyses are discussed as well.

Gulino, D. A.↗
NASA NTRS1987

Oxidation-resistant reflective surfaces for solar dynamic power generation in near earth orbit

Reflective surfaces for Space Station power generation systems are required to withstand the atomic oxygen-dominated environment of near earth orbit. Thin films of platinum and rhodium, which are corrosion resistant reflective metals, have been deposited by ion beam sputter deposition onto various substrate materials. Solar reflectances were then measured as a function of time of exposure to a RF-generated air plasma.

Gulino, Daniel A.↗
DOE OSTI2022

Anticorrosive epoxy coatings from direct epoxidation of bioethanol fractionated lignin

The development of lignin-based anticorrosive epoxy coatings for steel protection is beneficial for both alleviating the fossil resource depletion and value-added utilization of lignin but remains a challenge due to the inherent heterogeneous structure of lignin. Here, in this study, we selectively extract the low molecular weight (MW) fraction of a crop residue-derived enzymatic hydrolysis lignin (EHL) through a bioethanol fractionation process and prepare epoxy resin by direct epoxidation of the bioethanol fractionated lignin (BFL). The coatings are then fabricated using 20–100 wt% of BFL-based epoxy resin (LEp) as the commercial epoxy resin substitute. The low MW and high p-hydroxyphenyl content of the BFL offer high solubility and good workability for BFL and LEp during epoxidation and coating production, respectively. Lignin-based coatings with 20–40 wt% LEp exhibit good adhesion property (5B) and superior corrosion resistance, compared to the commercial epoxy coating. Although coating with high LEp concentrations (i.e., 60–100 wt%) resulted in decreased adhesion strength, the coating with 100 wt% LEp still displayed corrosion protection performance comparable to that of the commercial epoxy coating. Overall, this study provides a simple and effective approach to converting lignin to epoxy resins for a wide variety of surface coating applications.

09 BIOMASS FUELS↗
DOE OSTI2024

Spectro-electrochemistry of vanadium ions in LiCl-KCl-VCl2,3

Owing to their relatively high thermal conductivity and corrosion resistance, and low radiation heating and embrittlement properties, vanadium (V) alloys are being considered for fusion blanket structural materials. As such, the fundamental behavior of these materials, including the speciation of their corrosion products in molten lithium salts, must be elucidated to enable quantitative lifetime prediction. Yuan et al. [REF#1] demonstrated the reduction and oxidation of vanadium ions in molten LiCl-KCl eutectic salt using a tungsten wire, indicating the possibility of metallic vanadium reduction from V3+ negative potentials

36 - MATERIALS SCIENCE↗
DOE OSTI2020

Ab initio Study of the Mechanism for the Initiation of Localized Corrosion on Stainless Steel

Stainless steels are widely used as primary piping material in PWR’s because of their high corrosion resistance largely due to the formation of a passive film of metal oxides, such as chromium (e.g., Cr2O3). However, upon exposure to aggressive ions like chlorides (Cl-), stainless steel becomes susceptible to localized corrosion due to the breakdown of the passive film. It is therefore essential to gain fundamental insights into the mechanism of the passive film breakdown (depassivation) to develop a tailored design to minimize localized corrosion. This project investigates the initial stages of the depassivation of the Cr passive film using density functional theory (DFT), a quantum based computational method.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High-temperature corrosion of a nickel-based alloy in a molten chloride environment – The effect of thermal and chemical purifications

There is currently an ever-increasing demand for higher process efficiencies in next generation (Gen3) concentrating solar power (CSP). Higher process efficiencies may be procured by increasing the operating temperature, and simultaneously, minimizing the degradation of materials used for construction of CSP plants (e.g., piping, thermal storage tanks, solar receivers and heat exchangers). Thus, understanding materials corrosion in the presence of molten salt mixtures used as thermal energy storage media and heat transfer fluids is indispensable for CSP development. The present paper provides insights into the effects of salt purification on the corrosion of a nickel-based alloy (Haynes 230) isothermally exposed to a stagnant chloride-based salt mixture at 800 °C. The MgCl 2 -based salt mixture was thermally dehydrated and chemically treated with (0.1 and 0.5 wt %) elemental magnesium. Results reveal the electrochemical nature of the corrosion process, and the formation of corrosion products such as oxides (MgO, MgCr 2 O 4 , and MgAl 2 O 4 ) and nitrides (CrN) on the alloy surface and in sub-surface regions. Magnesium additions enhanced the ability to resist corrosion by reducing the concentration of impurities (H 2 O, MgOH + , OH - species) and polarizing the alloy surface. The formation of nitrides in all cases studied indicates the impact of using nitrogen as a protective gas in the system. Results also reveal that a single step treatment of the salt using metallic Mg could be considered as a measure to control the salt's impurity level, e.g., if required for system control.

14 SOLAR ENERGY↗
DOE OSTI2021

Effect of High Temperature CO 2 on Haynes 230 Alloy (Updated Jan 2021)

The supercritical carbon dioxide (sCO 2 ) Brayton cycle is a promising candidate for future nuclear reactors due to its ability to improve power cycle energy conversion efficiency. The sCO 2 Brayton cycle can operate with an efficiency of 45-50% at operating temperatures of 550-700 C. One of the greatest hurdles currently faced by sCO 2 Brayton cycles is the corrosivity of sCO 2 and the lack of long-term alloy corrosion and mechanical performance data, as these will be key to enhancing the longevity of the system, and thus the levelized cost of electricity. Past studies have shown that sCO 2 corrosion occurs through the formation of metal carbonates, oxide layers, and carburization, and alloys with Cr, Mo and Ni generally exhibit less corrosion. While stainless steels may offer sufficient corrosion resistance at the lower range of temperatures seen by the sCO 2 Brayton cycles, more expensive nickel-based alloys are typically needed for the higher temperature regions. This study investigates the effects of corrosion on the Haynes 230 alloy, with a preliminary view on changes in the mechanical properties. High temperature CO 2 is used for this study as the corrosion products are similar to that of supercritical CO 2 , allowing for an estimation of the susceptibility towards corrosion without the need for high pressure experimentation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multiscale Development and Validation of the Stainless Steel Alloy Corrosion (SStAC) Tool for High Temperature Engine Materials

The goal of this project was to create a simulation tool to assist in part design, reducing costs by eliminating the need for conservative material selection, and enabling alloy optimization to improve corrosion resistance. Thus, it helps decrease costs for existing engines and assists in the material and engine design for the engines of the future. To meet our stated goal, we developed the Stainless-Steel Alloy Corrosion (SStAC) tool, which: (1) Models corrosion of engine valves fabricated from 21-2N valve steel in an engine environment at temperatures up to 800 °C. (2) Runs in 1D for a fast estimate of the corrosion rate, and in 2D or 3D for more detailed simulations that represent any part geometry and predict the precise location and rate of corrosion and its impact on the mechanical and thermal behavior. (3) Was implemented using the open-source Multiphysics Object Oriented Simulation Environment (MOOSE). (4) Couples the corrosion model with mechanics and thermal transport models. The SStAC tool can predict the corrosion rate of 21-2N engine valves with less than 10% error.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Development of hydrogen resistant structural alloy NASA-23

Hydrogen-resistant alloy NASA-23 was developed specifically as a structural alloy for application in liquid propulsion systems that use hydrogen fuel. NASA-23 was designed to be similar to Alloy 718 in strength, ductility, and corrosion resistance, but with superior resistance to hydrogen environment embrittlement. The alloy is readily processed; it can be both hot and cold worked and is castable and weldable. A material property data base is being generated for both cast and wrought NASA-23. This paper will present the status of alloy development and discuss potential applications in propulsion systems.

Bhat, B. N.↗
DOE OSTI2024

Advanced neutron absorber Ni-Cr-Mo-Gd alloys seawater corrosion mechanism and susceptibility study

Previous studies demonstrated the corrosion susceptibility of advanced neutron absorber (ANA) Ni-Cr-Mo-Gd in a seawater environment but remained inconclusive. In this paper, scanning electron microscopy was employed to identify the corrosion phase in Ni-Cr-Mo-Gd, and computational thermodynamic simulation was used to study phase corrosion potentials. Results showed that the Ni 5 Gd second phase, distributed along FCC grain boundaries in Ni-Cr-Mo-Gd, has lower corrosion potential than the substrate. Furthermore, heat treatment and alloy chemistry adjustment would not ameliorate the ANA corrosion susceptibility. Finally, isolating the Ni 5 Gd from the corrosion medium through advanced manufacturing is a viable way to improve the ANA corrosion resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Milestone Report: Effect of High Temperature CO 2 on Haynes 230 Alloy

The supercritical carbon dioxide (sCO 2 ) Brayton cycle is a promising candidate for future nuclear reactors due to its ability to improve power cycle energy conversion efficiency. The sCO 2 Brayton cycle can operate with an efficiency of 45-50% at operating temperatures of 550-700 C. One of the greatest hurdles currently faced by sCO 2 Brayton cycles is the extreme corrosivity of sCO 2 . This affects the longevity of the power cycle and thus the levelized cost of electricity. Past studies have shown that sCO 2 corrosion occurs through the formation of metal carbonates, oxide layers, and carburization, and alloys with Cr, Mo and Ni generally exhibit less corrosion. While stainless steels may offer sufficient corrosion resistance at the lower range of temperatures seen by the sCO 2 Brayton cycles, more expensive alloys such as Inconel and Haynes are typically needed for the higher temperature regions. This study investigates the effects of corrosion on the Haynes 230 alloy, focusing on changes in the mechanical properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2024

Plasma Rapid Oxidation Technique for Extending Component Tenability (PROTECT)

Additive manufacturing (AM) is increasingly utilized in aerospace applications. However, post-processing is required for many applications, so intricate designs are limited. Plasma electrolytic oxidation (PEO) was investigated as a post-processing treatment on Ti-6-4 (or Ti-6Al-4V: Alpha-beta titanium alloy with a high specific strength and excellent corrosion resistance)additively manufactured specimens. The “Keronite Black” PEO treatment reduced the surface roughness (Ra) of test specimens by approximately 0.5 μm. This reduction in Ra compared to the as-printed sample was hypothesized to benefit corrosion and fatigue properties because increased Ra is known to negatively impact corrosion and fatigue characteristics. Up to a 101% improvement in the corrosion potential (Ɛcorr) was observed. Although fatigue characteristics varied by PEO parameters, there was no significant fatigue debit due to the PEO treatment. Additionally, no effect to adhesion characteristics was observed due to PEO treatment. It is recommended that additional studies investigate the ability of PEO treatments to improve the corrosion, fatigue, chemical compatibility, radiation hardening, particle shedding characteristics, and flammability/oxidizer compatibility of aerospace additively manufactured components.

Jennifer Williams↗