Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Camber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Comparison of experimental and theoretical thermal fatigue lives for five nickel-base alloys.

Alloys investigated were Nimonic 90, IN 100, coated IN 100, B 1900, coated B 1900, MAR M200, and MAR M200DS (directionally solidified). Maximum temperatures ranged from 770 to 1120 C. Specimen geometries included tapered disks, double-edged wedges, and cambered airfoils. The disks and wedges were heated and cooled in fluidized beds. The airfoil specimens were heated by a Mach 1 natural gas burner and rapid-air cooled, with and without spanwise loading. Life calculations included two distinct failure modes: conventional low-cycle fatigue and cyclic creep. The complete life calculation system included the calculation of transient temperature distributions, thermal strains, stresses, creep damage, fatigue damage, and finally cycles to first crack. Calculated lives were within a factor of two for 76 of the 86 data points analyzed.

Spera, D. A.↗
NASA NTRS1973

Steady inviscid transonic flows over planar airfoils: A search for a simplified procedure

A finite difference procedure based upon a system of unsteady equations in proper conservation form with either exact or small disturbance steady terms is used to calculate the steady flows over several classes of airfoils. The airfoil condition is fulfilled on a slab whose upstream extremity is a semi-circle overlaying the airfoil leading edge circle. The limitations of the small disturbance equations are demonstrated in an extreme example of a blunt-nosed, aft-cambered airfoil. The necessity of using the equations in proper conservation form to capture the shock properly is stressed. Ability of the steady relaxation procedures to capture the shock is briefly examined.

Magnus, R.↗
NASA NTRS1973

Subsonic characteristics of a twin-jet swept-wing fighter model with maneuvering devices

An investigation has been conducted at Mach numbers ranging from 0.06 to 0.94 to determine the effects of various combinations of leading-edge slat devices on the static aerodynamic characteristics of a twin-jet swept-wing fighter model. The study also included a determination of the effects of wing leading-edge droop, trailing-edge chord-extensions, wing fences, and wing-planform and camber modifications. The angle-of-attack range generally extended from about minus 2 deg to 24 deg and the sideslip angles ranged from about minus 6 deg to 13 deg.

Ray, E. J.↗
NASA NTRS1973

Highly loaded multi-stage fan drive turbine-cascade test program

Test results are presented for 19 cascades involving five plain and two tandem blade sections. High camber and/or negative reaction is associated with six of the sections. Exit Mach numbers range up to slightly above sonic. Cascade efficiency, exit flow angle and static pressure, and blade surface pressure data are reported with incidence angle, Mach number, solidity, and relative position of the tandem blades as independent variables.

Cherry, D. G.↗
NASA NTRS1973

Investigation of boundary layer and turbulence characteristics inside the passages of an axial flow inducer

A study of the boundary layer and turbulence characteristics inside the passages of an axial flow inducer is reported. The first part deals with the analytical and experimental investigation of the boundary layer characteristics in a four bladed flat plate inducer passage operated with no throttle. An approximate analysis for the prediction of radial and chordwise velocity profiles across the passage is carried out. The momentum integral technique is used to predict the gross properties of the boundary layer. Equations are given for the exact analysis of the turbulent boundary layer characteristics using the turbulent field method. Detailed measurement of boundary layer profiles, limiting streamline angle and skin friction stress on the rotating blade is also reported. Part two of this report deals with the prediction of the flow as well as blade static pressure measurements in a three bladed inducer with cambered blades operated at a flow coefficient of 0.065. In addition, the mean velocity and turbulence measurements carried out inside the passage using a rotating triaxial probe is reported.

Anand, A.↗
NASA NTRS1973

Boundary condition program for aerodynamic lifting surface theory

Users manual for a U.S.A. FORTRAN 4 computer program which determines boundary conditions for a thin wing lifting surface program is described. This program, the geometry program, and several other programs are used together in the analysis of lifting, thin wings in steady, subsonic flow according to a kernel function lifting surface theory. The program calculates specific types of boundary conditions automatically such as those necessary to determine pitch and roll damping derivatives. The program also accepts descriptions of the camber or downwash and twist in the form of tables and/or coefficients of equations. The program performs interpolations so that tables and/or coefficients can apply at stations selected by the user and not at stations dictated by the control point locations.

Medan, R. T.↗
NASA NTRS1974

A rapid numerical solution to subsonic flow over planar and axisymmetric profiles at an angle of attack of 0 deg

A numerical solution is presented for the incompressible flow over thin planar and axisymmetric profiles at an angle of attack of 0 degrees. The method uses a finite-difference field solution to the governing equation with a Gauss-Seidel successive overrelaxation scheme. However, the use of a simple Cartesian grid system restricts this method to slender profiles. Results are presented for a cambered airfoil, airfoil in wall effect (two-dimensional flowthrough inlet), body of revolution, and flowthrough nacelle. A computer program is presented which can be used for any of the previously mentioned cases with simple input changes. Results for compressible flow are available with the use of the appropriate two-dimensional or axisymmetric compressibility corrections. Computational time for a typical field calculation of 3000 grid points and 200 cycles through the field is less than 1 minute with less than 50,000 octal storage on the Control Data Corporation 6600 computing system.

Mascitti, V. R.↗
NASA NTRS1974

Comparisons of two-dimensional shock-expansion theory with experimental aerodynamic data for delta-planform wings at high supersonic speeds

An investigation has been conducted to explore the potential for optimizing airfoil shape at high supersonic speeds by utilizing the two-dimensional shock-expansion method. Theoretical and experimental force and moment coefficients are compared for four delta-planform semispan wings having a leading-edge sweep angle of 65 deg and incorporating modified diamond airfoils with a thickness-chord ratio of 0.06. The wings differ only in airfoil maximum-thickness position and camber. The experimental data are obtained at Mach numbers of 3.95 and 4.63 and at a Reynolds number of 9.84 million per meter. A relatively simple method is developed for predicting, in terms of lift-drag ratio, the optimum modified diamond airfoil at high supersonic and hypersonic speeds.

Jernell, L. S.↗
NASA NTRS1974

Analysis of wing-body interaction flutter for a preliminary space shuttle design

Subsonic flutter analyses for a preliminary space shuttle design were performed to determine the effect of wing-body aerodynamic interaction on the vehicle flutter speed. It was found that the proximity of the large bodies of the shuttle to the wing reduces critical flutter speed by 11%. Aerodynamic reflection off the bodies is the dominant interaction effect while aerodynamic forces caused by body motion are of secondary importance in most cases. The analyses employed a doublet-lattice representation of the space shuttle, where in the wing and body surfaces were modeled by a lattice of nonplanar lifting surface elements. Axial singularities were introduced to account for body incidence, volume, and camber (slender body) effects. A series of studies on the placement and number of these elements was performed to ensure convergence of the results.

Chipman, R. R.↗
NASA NTRS1974

Longitudinal aerodynamic performance of a series of power-law and minimum wave drag bodies at Mach 6 and several Reynolds numbers

Experimental data have been obtained for two series of bodies at Mach 6 and Reynolds numbers, based on model length, from 1.4 million to 9.5 million. One series consisted of axisymmetric power-law bodies geometrically constrained for constant length and base diameter with values of the exponent n of 0.25, 0.5, 0.6, 0.667, 0.75, and 1.0. The other series consisted of positively and negatively cambered bodies of polygonal cross section, each having a constant longitudinal area distribution conforming to that required for minimizing zero-lift wave drag at hypersonic speeds under the geometric constraints of given length and volume. At the highest Reynolds number, the power-law body for minimum drag is blunter (exponent n lower) than predicted by inviscid theory (n approximately 0.6 instead of n = 0.667); however, the peak value of lift-drag ratio occurs at n = 0.667. Viscous effects were present on the bodies of polygonal cross section but were less pronounced than those on the power-law bodies. The trapezoidal bodies with maximum width at the bottom were found to have the highest maximum lift-drag ratio and the lowest mimimum drag.

Ashby, G. C., Jr.↗
NASA NTRS1974

Design and testing of a tandem row pump inducer

The design and testing of a tandem row pump inducer having a supercavitating first stage with a 0.60 hub ratio is presented. The second stage tested was a helical impeller with a 0.70 hub ratio. A cubic arc transition was utilized to accomplish the hub change. The first stage had two blades and the free-vortex design approach was empirically modified based on previous experience. The recommended second stage design having four blades and using cambered blade section is presented but the model was not built or tested. The more simple helix was built instead to reduce cost. Data taken included head generation, cavitation observations and unsteady head fluctuations over the 0-100Hz range.

Etter, R. J.↗
NASA NTRS1974

Low-speed aerodynamic characteristics of a hypersonic research airplane concept having a 70 deg swept delta wing

An experimental investigation of the low-speed static longitudinal, lateral and directional stability characteristics of a hypersonic research airplane concept having a 70 deg swept delta wing was conducted in a low-speed tunnel with a 12-foot (3.66 meter) octagonal test section. Aircraft component variations included: (1) fuselage shape modifications, (2) tip fins, (3) center vertical fin, (4) wing camber, and (5) wing planform. This investigation was conducted at a dynamic pressure of 262.4 Pa (5.48 psf), a Mach number of 0.06, and a Reynolds number of 2.24 million, based on body length. Tests were conducted through an angle-of-attack range of 0 deg to 30 deg with elevon deflections from +5.0 deg to minus 30.0 deg. The complete configuration exhibited positive static longitudinal, lateral and directional stability up to angles of attack of at least 20 deg and was trimmable to lift coefficients of at least 0.70 with elevon deflections of minus 30 deg.

Creel, T. R., Jr.↗
NASA NTRS1974

Low-speed aerodynamic characteristics of airfoil sections with rounded trailing edges in forward and reverse flow

Low-speed wind-tunnel tests were conducted to determine the two-dimensional aerodynamic characteristics of 6-, 12-, and 18-percent-thick airfoil sections with rounded trailing edges in both forward and reverse flow. The shapes incorporated camber with both the leading and trailing edges rounded to provide reasonable aerodynamic performance with either edge directed toward the free-stream flow. The tests were conducted with the airfoils in both normal and reverse orientations relative to the free stream. The Mach number was varied from 0.16 to 0.36 and the angle of attack was varied from minus 10 to 24 million. Reynolds number, based on the airfoil chord, was varied from about 1.0 to 12.0 million.

Beasley, W. D.↗
NASA NTRS1974

Development of a computer program to obtain ordinates for NACA-6 and 6A-series airfoils

A computer program was developed to produce the ordinates for airfoils of any thickness, thickness distribution, or camber in the NACA 6- and 6A-series. For the 6-series and for all but the leading edge of the 6A-series, agreement between the ordinates obtained from the new program and previously published values is generally within .00005 chord. Near the leading edge of the 6A-series airfoils, differences up to .00035 chord are found.

Ladson, C. L.↗
NASA NTRS1974

Supercirculation effects induced by vectoring a partial-span rectangular jet

Thrust-induced supercirculation effects from thrust vectoring have indicated a potential for not only increasing maneuverability of fighter aircraft but also as a means of improving cruise performance. The current study investigated a partial-span rectangular jet-exhaust nozzle located at the wing trailing edge that acts similar to a jet flap by increasing lift due to supercirculation. This paper summarizes experimental studies including the effects of nozzle deflection angle, wing camber, and nozzle shape and exit location on lift, drag and load distributions. The results indicate that significant increases in thrust-induced lift along with substantial decreases in drag are possible.

Capone, F. J.↗
NASA NTRS1974

Review of NASA supercritical airfoils

NASA supercritical airfoils are characterized by a substantially reduced curvature of the midcord region of the upper surface together with increased camber near the trailing edge. The basic aerodynamic phenomena associated with the airfoils and representative wind tunnel results are discussed. The results indicate that the drag rise Mach numbers for NASA supercritical airfoils are 0.1 higher than for comparable NACA 6-series airfoils. A recent analytic method for predicting the aerodynamic characteristics of supercritical airfoils is described. The flight demonstration programs of three applications of supercritical airfoils utilizing the F-8, T-2C and F-111 as test beds are summarized.

Whitcomb, R. T.↗
NASA NTRS1974

Theoretical prediction of thick wing and pylon-fuselage-fanpod-nacelle aerodynamic characteristics at subcritical speeds. Part 1: Theory and results

The theoretical development and the comparison of results with data of a thick wing and pylon-fuselage-fanpod-nacelle analysis are presented. The analysis utilizes potential flow theory to compute the surface velocities and pressures, section lift and center of pressure, and the total configuration lift, moment, and vortex drag. The skin friction drag is also estimated in the analysis. The perturbation velocities induced by the wing and pylon, fuselage and fanpod, and nacelle are represented by source and vortex lattices, quadrilateral vortices, and source frustums, respectively. The strengths of these singularities are solved for simultaneously including all interference effects. The wing and pylon planforms, twists, cambers, and thickness distributions, and the fuselage and fanpod geometries can be arbitrary in shape, provided the surface gradients are smooth. The flow through nacelle is assumed to be axisymmetric. An axisymmetric center engine hub can also be included. The pylon and nacelle can be attached to the wing, fuselage, or fanpod.

Tulinius, J. R.↗
NASA NTRS1974

Influence of propulsion system size, shape, and location on supersonic aircraft design

The effects of various propulsion system parameters on the characteristics of a supersonic transport were investigated. The effects of arbitrarily scaling engine size on wave drag, friction drag, drag-due-to-lift, wing sizing, airplane balance, and airplane weight were studied. These evaluations were made for two families of nacelle shapes, resulting from typical turbojet and turbofan installations. Also examined were effects of nacelle location, and the wing camber plane deformations required to cancel the nacelle interference pressure field at cruise Mach number (2.7 M) were determined. The most drag-sensitive parameter is found to be nacelle shape. Similarly, wing deformation requirements are found to be primarily affected by nacelle shape. Effects of engine size variations are noted primarily in airplane gross weight.

Bonner, E.↗