Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Using a Phenomenological Computer Model to Investigate Advanced Combustion Trajectories in a CIDI Engine

This paper summarizes results from simulations of conventional, high-dilution, and high-efficiency cleancombustion in a diesel engine based on a two-zone phenomenological model. The two-zone combustionmodel is derived from a previously published multi-zone model, but it has been further simplified toincrease computational speed by a factor of over 100. The results demonstrate that this simplified modelis still able to track key aspects of the combustion trajectory responsible for NOx and soot production. Inparticular, the two-zone model in combination with highly simplified global kinetics correctly predictsthe importance of including oxygen mass fraction (in addition to equivalence ratio and temperature)in lowering emissions from high-efficiency clean combustion. The methodology also provides a convenient framework for extracting information directly from in-cylinder pressure measurements. This feature is likely to be useful for on-board combustion diagnostics and controls. Because of the possibilityfor simulating large numbers of engine cycles in a short time, models of this type can provide insight into multi-cycle and transient combustion behavior not readily accessible to more computationally intensive models. Also the representation of the combustion trajectory in 3D space corresponding to equivalence ratio, flame temperature, and oxygen fraction provides new insight into optimal combustionmanagement.

33 ADVANCED PROPULSION SYSTEMS↗

TAILORED BIOBLENDSTOCKS WITH LOW ENVIRONMENTAL IMPACT TO OPTIMIZE MCCI ENGINES

The overall objective of the project is to develop and demonstrate a microalgae bio-blendstock with greater than 60% greenhouse gas reduction potential relative to petroleum diesel, that can reduce sooting propensity, increase cetane number and improve engine thermal efficiency relative to a baseline diesel engine operating on conventional fuel. Specific objectives include: (1) development of a new framework for both LCA and TEA that explicitly considers temporal variation in productivity and the frequency of crop loss; (2) determination of how fuel compounds that can be produced from the algal biomass can be ‘bio-tailored’ based on the species composition and biological production process, and subsequent processing via HTL to biocrude, and upgrading of the biocrude; (3) execution of a feedback loop (algae production  biocrude refining  combustion optimization  feedback to refining stage), for optimization of fuels for MCCI combustion; (4) optimization of MCCI combustion and emissions performance, accounting first for the biological processes that dictate the chemical composition of biocrude oil, and second for the subsequent chemical processes that comprise mixing controlled compression ignition combustion; (6) simulation of MCCI engine combustion processes to demonstrate the incorporation of relevant fuel chemistry that captures the specific impacts of optimized algal fuels.

09 BIOMASS FUELS↗

Tailored Bioblendstocks with Low Environmental Impact to Optimize MCCI Engines

The overall objective of the project is to develop and demonstrate a microalgae bio-blendstock with greater than 60% greenhouse gas reduction potential relative to petroleum diesel, that can reduce sooting propensity, increase cetane number and improve engine thermal efficiency relative to a baseline diesel engine operating on conventional fuel. Specific objectives include: (1) development of a new framework for both LCA and TEA that explicitly considers temporal variation in productivity and the frequency of crop loss; (2) determination of how fuel compounds that can be produced from the algal biomass can be ‘bio-tailored’ based on the species composition and biological production process, and subsequent processing via HTL to biocrude, and upgrading of the biocrude; (3) execution of a feedback loop (algae production  biocrude refining  combustion optimization  feedback to refining stage), for optimization of fuels for MCCI combustion; (4) optimization of MCCI combustion and emissions performance, accounting first for the biological processes that dictate the chemical composition of biocrude oil, and second for the subsequent chemical processes that comprise mixing controlled compression ignition combustion; (6) simulation of MCCI engine combustion processes to demonstrate the incorporation of relevant fuel chemistry that captures the specific impacts of optimized algal fuels.

09 BIOMASS FUELS↗

Design and evaluation of an oxidant-fuel-ratio-zoned rocket injector for high performance and ablative engine compatibility

A method for temperature control of the combustion gases in the peripheral zone of a rocket combustor which would reduce ablative throat erosion, prevent melting of zirconia throat inserts, and maintain high combustion performance is discussed. Included are techniques for analyzing and predicting zoned injector performance, as well as the philosophy and method for accomplishing an optimum compromise between high performance and reduced effective gas temperature. The experimental work was done with a 1000-lbf rocket engine which used as propellants N2O4 and a blend of 50-percent N2H4 and 50-percent UDMH at 100-psia chamber pressure and an overall O/F of 2.0. The method selected to provide temperature control was to use 30 percent of the propellant to form a peripheral zone of combustion gases at an O/F of 1.31 and 2700 K. The remaining 70 percent of the propellant in the core was at an O/F of 2.45 to keep the overall O/F at 2.0.

Winter, J. M.↗

Techniques for enhancing durability and equivalence ratio control in a rich-lean, three-stage ground power gas turbine combustor

Rig tests of a can-type combustor were performed to demonstrate two advanced ground power engine combustor concepts: steam cooled rich-burn combustor primary zones for enhanced durability; and variable combustor geometry for three stage combustion equivalence ratio control. Both concepts proved to be highly successful in achieving their desired objectives. The steam cooling reduced peak liner temperatures to less than 800 K. This offers the potential of both long life and reduced use of strategic materials for liner fabrication. Three degrees of variable geometry were successfully implemented to control airflow distribution within the combustor. One was a variable blade angle axial flow air swirler to control primary airflow while the other two consisted of rotating bands to control secondary and tertiary or dilution air flow.

Schultz, D. F.↗

Hypersonic propulsion research

The NASA Langley Research Center has conducted hypersonic propulsion research since the 1960s. A variety of inlet concepts were explored and characterized. The emphasis of the inlet program was the development of the short (light weight), fixed geometry, side-wall-compression inlets that operate efficiently over a wide Mach number range. As hypersonic combustion tunnels were developed, programs to study the parameters controlling fuel mixing and combustion with single and multiple strut models were conducted using direct connect test techniques. These various tests supported the design of subscale engine test hardware that integrated inlet and combustor technology and allowed the study of the effect of heat release on thrust and combustor/inlet interaction. A number of subscale engine tests have demonstrated predicted performance levels at Mach 4 and 7 simulated flight conditions.

Northam, G. Burton↗

Hypersonic propulsion research

The development of technology for the modular airframe integrated scramjet has been the focus of hypersonic propulsion research for several years. An part of this research, a variety of inlet concepts have been explored and characterized. The emphasis of the inlet program has been the development of the short (light weight), fixed geometry, side wall compression inlets that operate efficiently over a wide Mach number range. As hypersonic combustion tunnels were developed, programs to study the parameters controlling fuel mixing and combustion with single and multiple strut models were conducted using direct connect test techniques. These various tests supported the design of subscale engine test hardware that integrated inlet and combustor technology and allowed the study of the effect of heat release on thrust and combustor/inlet interaction. A number of subscale engine tests have shown predicted performance levels at Mach 4 and 7 simulated flight conditions. A few of the highlights from this research program are summarized.

Northam, G. Burton↗

Relation of Turbojet and Ramjet Combustion Efficiency to Second-Order Reaction Kinetics and Fundamental Flame Speed

Theoretical studies of the turbojet and ramjet combustion process are summarized and the resulting equations are applied to experimental data obtained from various combustor tests. The theoretical treatment assumes that one step in the over-all chain of processes which constitute jet-engine combustion is sufficiently slow to be the rate-controlling step that determines combustion efficiency.

Childs, J Howard↗

Investigating the Combustion Performance of Dual Fuel Combustion with Diesel and Port Injected Hydrogen in a Large Bore Locomotive Engine

The heavy-duty transportation sector has primarily relied on conventional diesel combustion engines given their reliability and high thermal efficiency relative to spark ignition engines, but increased focus on reducing greenhouse gas emissions has led to investigation into alternative fuels. Gaseous hydrogen fuel has garnered a great deal of recent interest in the engine community given it has zero carbon, but hydrogen is not available at the scale and cost that petroleum fuels are currently available, and this is a barrier to adoption for industries that are looking to decarbonize their operations. Because of the fuel flexibility provided, dual fuel technology offers a pathway for some industries to adopt hydrogen as a fuel source while maintaining sufficient flexibility in times and locations where the new fuel is not yet available. This computational study investigates dual fuel combustion in a large bore locomotive engine architecture using direct injected diesel and port injected gaseous hydrogen fuel. With an optimal port fuel injection configuration from previous work, simulations of varying substitution ratio, compression ratio, manifold air temperature, diesel injection timing, and diesel injection pressure were performed to understand their effect on combustion performance. Results indicated that both increased substitution ratio and higher intake air temperature accelerates hydrogen flame propagation and can result in high peak cylinder pressures. Additionally, diesel injection timing and injection pressure were demonstrated as effective methods for controlling dual fuel combustion heat release rates.

ODonnell, Patrick Christopher↗

Analysis of Thermal and Chemical Effets on Negative Valve Overlap Period Energy Recovery for Low-Temperature Gasoline Combustion

A central challenge for efficient auto-ignition controlled low-temperature gasoline combustion (LTGC) engines has been achieving the combustion phasing needed to reach stable performance over a wide operating regime. The negative valve overlap (NVO) strategy has been explored as a way to improve combustion stability through a combination of charge heating and altered reactivity via a recompression stroke with a pilot fuel injection. The study objective was to analyze the thermal and chemical effects on NVO-period energy recovery. The analysis leveraged experimental gas sampling results obtained from a single-cylinder LTGC engine along with cylinder pressure measurements and custom data reduction methods used to estimate period thermodynamic properties. The engine was fueled by either iso-octane or ethanol, and operated under sweeps of NVO-period oxygen concentration, injection timing, and fueling rate. Gas sampling at the end of the NVO period was performed via a custom dump-valve apparatus, with detailed sample speciation by in-house gas chromatography. The balance of NVO-period input and output energy flows was calculated in terms of fuel energy, work, heat loss, and change in sensible energy. Experiment results were complemented by detailed chemistry single-zone reactor simulations performed at relevant mixing and thermodynamic conditions, with results used to evaluate ignition behavior and expected energy recovery yields. For the intermediate bulk-gas temperatures present during the NVO period (900-1100 K), weak negative temperature coefficient behavior with iso-octane fueling significantly lengthened ignition delays relative to similar ethanol fueled conditions. Faster ethanol ignition chemistry led to lower recovered fuel intermediate yields relative to similar iso-octane fueled conditions due to more complete fuel oxidation. From the energy analysis it was found that increased NVO-period global equivalence ratio, either from lower NVOperiod oxygen concentrations or higher fueling rates, in general led to a greater fraction of net recovered fuel energy and work as heat losses were minimized. These observations were supported by complementary single-zone reactor model results, which further indicated that kinetic time-scales favor chemical energy-consuming exothermic oxidation over slower endothermic reformation. Nonetheless, fuel energy recovery close to the thermodynamic equilibrium solution was achieved for baseline conditions that featured 4% NVO-period oxygen concentration.

ethanol↗

Computational diagnostics and characterization of combustion recession in diesel sprays

While low-temperature combustion (LTC) strategies have been found to mitigate nitrogen oxides and particulate matter emissions in diesel engines, studies have also associated LTC with an increase in unburnt hydrocarbons. With more recent studies on diesel after end-of-injection (AEOI), combustion recession is identified as a phenomenon where at near nozzle region, high-temperature ignition (HTI) combustion can propagate back to the nozzle tip consuming the unburnt hydrocarbons AEOI. Current literature has suggested that combustion recession is controlled by auto-ignition. However, high-fidelity simulations and detailed analysis of such a mechanism are missing. In this study, comprehensive Large Eddy Simulations of a reacting spray at “Spray A” conditions are performed, where detailed analysis of combustion recession concerning flame morphology and propagation modes are included. In particular, this study demonstrated for the first time that while combustion recession is mainly auto-ignition dominated (consistent with the literature), a cool flame was found to deflagrate towards the richer regions of the mixture, promoting mixing and increasing the mixture temperature. This leads to HTI kernels, which then grow and develop as deflagrative waves, therefore sustaining the combustion recession process. The study also detailed the extinction mechanism of combustion: the entrainment wave will overlean the near-nozzle mixtures, rendering it unable to support HTI, which leads to the extinction of the upstream flame AEOI in lower reactivity mixtures. Combustion recession is also observed to be contingent on the chemical and diffusion processes, even at low scalar dissipation rates. Finally, a new criterion for combustion recession based on chemical explosive mode is proposed and validated with previous combustion recession index to quantify the extent of HTI in near-nozzle mixtures AEOI. The newly developed metric combined with a previous experimentally-based metric can provide simple but valuable measurements of the degree and propensity of the upstream flame AEOI.

CEMA↗

Research on oxidation by air and tempering of Raney nickel electrocatalysts for the H2 anodes of alkali combustion materials cells

The controlled oxidation in air of Raney nickel electrocatalysts was studied, with special attention paid to the quantitative analysis of nickel hydroxide. The content of the latter was determined through X-ray studies, thermogravimetric measurements, and spectral photometric examinations. The dependence of the content on the drying of activated catalyst is determined. The influence of nickel hydroxide on the electrochemical parameters of the catalyst, such as diffusion polarization, is studied, including a measurement of the exchange current density using the potential drop method. Conservation by oxidation in air with ancillary stabilization of the oxide in an H2 flow at 300 C is explored, including reduction by H2, the influence of tempering time, and structural studies on conserved and stabilized catalyst, long term research on the catalyst, including the influence of aging on the reduced catalyst, and the results of impedance measurements are presented.

Selbach, H. J.↗

Researches on direct injection in internal-combustion engines

These researches present a solution for reducing the fatigue of the Diesel engine by permitting the preservation of its components and, at the same time, raising its specific horsepower to a par with that of carburetor engines, while maintaining for the Diesel engine its perogative of burning heavy fuel under optimum economical conditions. The feeding of Diesel engines by injection pumps actuated by engine compression achieves the required high speeds of injection readily and permits rigorous control of the combustible charge introduced into each cylinder and of the peak pressure in the resultant cycle.

Tuscher, Jean E↗

International Symposium on Combustion, 15th, Tokyo, Japan, August 25-31, 1974, Proceedings

Recent theoretical and experimental studies concerned with detonation and pressure wave combustion interaction, fire and explosion research and safety, heterogeneous combustion, flame-flow interactions, kinetics of elementary reactions, pollution control in and by combustion systems, and ignition are presented. Some of the topics covered include critical power density for direct initiation of unconfined gaseous detonations, extinction of laminar diffusion flames for liquid fuels, combustion of bulk titanium in oxygen, flame propagation in small spheres of unconfined and slightly confined flammable mixtures, kinetics of the reaction of nitric oxide with hydrogen, production of chemi-ions and formation of CH and CH2 radicals in methane-oxygen and ethylene-oxygen flames, NOx emission characteristics in two-stage combustion, and spherical ignition of oxyhydrogen behind a reflected shock wave. Individual items are announced in this issue.

Source record↗

Effect of Premixed Fuel Preparation for Partially Premixed Combustion with a Low Octane Gasoline on a Light-Duty Multi-Cylinder Compression Ignition Engine

Gasoline compression ignition concepts with the majority of the fuel being introduced early in the cycle are known as partially premixed combustion (PPC). Previous research on single- and multi-cylinder engines has shown that PPC has the potential for high thermal efficiency with low NOx and soot emissions. A variety of fuel injection strategies has been proposed in the literature. These injection strategies aim to create a partially stratified charge to simultaneously reduce NOx and soot emissions while maintaining some level of control over the combustion process through the fuel delivery system. The impact of the direct injection strategy to create a premixed charge of fuel and air has not previously been explored, and its impact on engine efficiency and emissions is not well understood. This paper explores the effect of sweeping the direct injected pilot timing from -91° to -324° ATDC, which is just after the exhaust valve closes for the engine used in this study. During the sweep, the pilot injection consistently contained 65% of the total fuel (based on command duration ratio), and the main injection timing was adjusted slightly to maintain combustion phasing near top dead center. A modern four cylinder, 1.9 L diesel engine with a variable geometry turbocharger, high pressure common rail injection system, wide included angle injectors, and variable swirl actuation was used in this study. The pistons were modified to an open bowl configuration suitable for highly premixed combustion modes. The stock diesel injection system was unmodified, and the gasoline fuel was doped with a lubricity additive to protect the high pressure fuel pump and the injectors. The study was conducted at a fixed speed/load condition of 2000 rpm and 4.0 bar brake mean effective pressure (BMEP). The pilot injection timing sweep was conducted at different intake manifold pressures, swirl levels, and fuel injection GTP-15-1067, Dempsey 2 pressures. The gasoline used in this study has relatively high fuel reactivity with a research octane number of 68. The results of this experimental campaign indicate that the highest brake thermal efficiency and lowest emissions are achieved simultaneously with the earliest pilot injection timings (i.e., during the intake stroke).

33 ADVANCED PROPULSION SYSTEMS↗

INVESTIGATION INTO REACTIVITY SEPARATION BETWEEN DIRECT INJECTED AND PREMIXED FUELS IN RCCI COMBUSTION MODE

This experimental study focuses on the effects of the reactivity separation between the port injected fuel and the direct injection fuel, the amount of external-cooled exhaust gas recirculation (EGR), and the direct injection timing of the high reactivity fuel on Reactivity Controlled Compression Ignition (RCCI) combustion. The experiments were conducted on a lightduty, single-cylinder diesel engine with a production GM/Isuzu engine head and piston and a retrofitted port fuel injection system. The global charge-mass equivalence ratio, ϕ′, was fixed at 0.32 throughout all of the experiments. To investigate the effects of the fuel reactivity separation, different Primary Reference Fuels (PRF) were port injected, with the PRF number varying from 50 to 90. To investigate the effects of EGR, an EGR range of 0 to 55% was used. To investigate the effects of the injection timing, an injection timing window of -65 to -45 degrees ATDC was chosen. The results indicate that there are several tradeoffs. First, decreasing the port injected fuel reactivity (increasing the PRF number) delays combustion phasing, decreases the combustion efficiency by up to 9%, increases the gross indicated thermal efficiency up to 22%, enhances the combustion sensitivity to the direct injection timing, and slightly increases the UHC, CO, and NOx emissions. Second, increasing the EGR percentage delays combustion phasing, lowers the peak heat release rate, and lowers the NOx emissions. The combustion efficiency first increases and then decreases with EGR percentage for high reactivity fuels (low PRF number), but only decreases for low reactivity fuels. Finally, delaying the injection timing advances combustion phasing and increases the combustion efficiency, but decreases the gross indicated thermal efficiency and increases the NOx emissions. Across all of the experiments, delays in CA50 increase the gross indicated thermal efficiency and decrease the combustion efficiency, which represents an inherent tradeoff for RCCI combustion on a lightduty engine.

Yan, Ziming↗