Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Boosting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Program verification document for the ASTP flight program

The various segments of the Apollo Soyuz Test Project (ASTP) flight program were verified. This included checks on the following: general verification, reference systems and transformations, launch preparations, boost navigation and guidance, orbital navigation and guidance, time bases, discretes, and interrupts, launch vehicle attitude control, switch selector processing, digital command system, real time telemetry and data compression, and algorithms.

Source record↗
NASA NTRS1975

Launch vehicle attitude control

The minor loop and minor loop support modules which maintain correct vehicle attitude control by generating vehicle attitude error signals were verified. The logic is checked during boost and orbit (unusual timing situations necessitate the additional orbit checks) and the constants used by these modules checked at every point during the flight. Since the same logic instructions are used throughout the flight with only the constants changing, verification of the logic at two points and the constants at all points verify the logic throughout the flight.

Source record↗
NASA NTRS1974

X-rays from an auroral substorm at altitudes of 60-80 km and 15-20 km

A technique for the measurement of high altitude X-rays associated with auroral events is described. The instrument package is boosted to the lower D region by a rocket and descends slowly by parachute. This arrangement facilitates coordination with the launching of other rocket probes during events of interest. A flight on Feb. 2, 1973 from the Churchill Research Range provided 17 minutes of X-ray data above 28 km. The flight was made into an intense break-up event and X-ray fluxes were observed during two episodes of the explosive phase. The reduction of auroral absorption during the later phases of the event suggests precipitation of energetic electrons unaccompanied by the lower energy precipitation responsible for the absorption earlier in the substorm.

Sheldon, W. R.↗
NASA NTRS1975

Simultaneous investigation of parent electrons and bremsstrahlung X rays by rocket-borne detectors

Simultaneous measurements of the energy spectrum of precipitating electrons and the resulting bremsstrahlung X-ray spectrum were carried out during an auroral event on March 3, 1971, at the Churchill Research Range, Manitoba, Canada. The electron data were obtained with detectors on a Black Brant VB sounding rocket (275-km apogee), while the X-ray flux was measured by an instrument package that was boosted to 60 km on an Arcas rocket. The X-ray package was deployed on a parachute at apogee to provide a slow descent through the atmosphere. Thick-target bremsstrahlung theory is used to calculate the X-ray flux produced by the incident electrons, and a Monte Carlo method is used to predict the X-ray spectrum at various altitudes appropriate for comparison with the measured X-ray data. Satisfactory agreement between theory and experiment is obtained, and the value of the constant in the thick target theory has been estimated to be about 0.00002.

Vij, K. K.↗
NASA NTRS1975

Joint USAF/NASA hypersonic research aircraft study

A joint USAF/NASA study has developed a conceptual design for a new high-speed research airplane (X-24C) and identified candidate flight research experiments in the Mach 3 to 6 speed range. Four major categories of high priority research experiments are described as well as the X-24C design concept. The vehicle, a rocket-boosted, delta planform aircraft, is air launched from a B-52 and is capable of forty seconds of rocket cruise at Mach 6 with a research scramjet. Research provisions include a dedicated 10-foot long research experiments section, removable fins and strakes, and provisions for testing integrated airbreathing propulsion systems.

F. S. Kirkham↗
NASA NTRS1975

Surface tension propellant acquisition system technology for Space Shuttle reaction control tanks

A program was conducted to provide the technology base for the SS/RCS flight tankage. Through a combination of analysis, subscale testing and computer predictions, a surface tension acquisition/expulsion system design was developed for the Orbiter RCS application. A full-scale tank system was fabricated and ground verification testing was conducted. Cleaning, inspection, fill and drain, and one-g expulsion performance were demonstrated. Results show that the fine-mesh screen, compartmented tank system provides the performance, flexibility, reusability, and other characteristics required by the pulsing, high flowrate RCS. It provides the required expulsion under widely differing high-g boost abort and reentry vectors oriented 119 deg apart and during on-orbit operation under omnidirectional low-g conditions.

Fester, D. A.↗
NASA NTRS1975

Utility of Space Transportation System to Space Communication Community

A potentially cost effective technique was investigated of launching operational satellites into synchronous orbit using the space transportation system (STS). This technique uses an unguided spinning solid rocket motor as the means for boosting a satellite from a low altitude shuttle parking orbit into a synchronous transfer orbit. The spacecraft is then injected into a geosynchronous orbit by an apogee kick motor fired at transfer orbit apogee. The approach is essentially that used on all Delta and Atlas-Centaur launches of synchronous satellites with the shuttle orbiter performing the function of the first two stages of the Delta three stage launch vehicle and the perigee kick motor performing the function of the Delta third state. It is concluded that the STS can be useful to the space communication community as well as to other geostationary satellite system users if the recommended actions are implemented.

Bronstein, L. M.↗
NASA NTRS1975

ASTP (SA-210) launch vehicle operational flight trajectory dispersion analysis, volume 1

In order to establish realistic deviation limits for the ASTP (SA-210) Launch Vehicle Operational Flight Trajectory, a dispersion analysis was conducted. The nominal trajectory prescribed for this analysis is the ASTP (SA-210) Launch Vehicle 500 Pound Launch Window Opening OT. The error sources considered are those associated with predictions of vehicle characteristics, vehicle systems performance, and flight environment. The nominal vehicle, the boost trajectory simulations, the error sources, the analytic procedures utilized, and the results are discussed. Launch vehicle guidance system inaccuracies were determined from the guidance error analysis. These data are composed of individual error source trajectory parameter dispersion envelopes.

Williams, N. D.↗
NASA NTRS1975

Clusius-Dickel Separations (CDS): A new look at an old technique

The history, applications, and theoretical basis of the CDS technique are reviewed. The advantage to be realized by conduction of CDSs in low-g, space environments are deduced. The results are reported of investigations aimed at further improving CDS efficiencies by altering convective flow patterns. The question of whether multicellular flow or turbulence can introduce a new separation mechanism which would boost separation efficiencies at least an order of magnitude is considered. Results are presented and discussed.

Grodzka, P. G.↗
NASA NTRS1975

Centaur zero gravity coast and engine restart demonstration on the Titan/Centaur (TC-2) extended mission

The Centaur propellant management and thermal control techniques required for zero gravity coasting were successfully demonstrated during an extended mission following spacecraft separation on the TC-2 flight. As part of the demonstration, two successful engine starts were accomplished. The first engine start followed a one-hour zero gravity coast, and the second engine start followed a three-hour zero gravity coast. All of the Centaur systems performed satisfactorily, the design parameters for zero gravity coasting were verified, and no significant problems were encountered. The flight results showed that the propellant location and behavior, propellant heating, and tank pressure rise rates observed during the zero-gravity coasts were less severe than expected. Consequently, the majority of the propellants remained at the tank bottom, the propellant collection times were very short, and more than 7 hours of coast could have been achieved before a tank venting was required. The tank pressurization prior to the engine starts provided boost pump Net Positive Suction Head values well in excess of the values required. The LO2 tank pressurization was accomplished by a new bubbler method that greatly reduced the helium usage.

Lacovic, R. F.↗
NASA NTRS1976

Evaluation of dispersion strengthened nickel-base alloy heat shields for space shuttle application

The results obtained in a program to evaluate dispersion-strengthened nickel-base alloys for use in a metallic radiative thermal protection system operating at surface temperatures to 1477 K for the space shuttle were presented. Vehicle environments having critical effects on the thermal protection system are defined; TD Ni-20Cr characteristics of material used in the current study are compared with previous results; cyclic load, temperature, and pressure effects on sheet material residual strength are investigated; the effects of braze reinforcement in improving the efficiency of spotwelded joints are evaluated; parametric studies of metallic radiative thermal protection systems are reported; and the design, instrumentation, and testing of full scale subsize heat shield panels in two configurations are described. Initial tests of full scale subsize panels included simulated meteoroid impact tests, simulated entry flight aerodynamic heating, programmed differential pressure loads and temperatures simulating mission conditions, and acoustic tests simulating sound levels experienced during boost flight.

Johnson, R., Jr.↗
NASA NTRS1976

Vibration characteristics of 1/8-scale dynamic models of the space-shuttle solid-rocket boosters

Vibration tests and analyses of six 1/8 scale models of the space shuttle solid rocket boosters are reported. Natural vibration frequencies and mode shapes were obtained for these aluminum shell models having internal solid fuel configurations corresponding to launch, midburn (maximum dynamic pressure), and near endburn (burnout) flight conditions. Test results for longitudinal, torsional, bending, and shell vibration frequencies are compared with analytical predictions derived from thin shell theory and from finite element plate and beam theory. The lowest analytical longitudinal, torsional, bending, and shell vibration frequencies were within + or - 10 percent of experimental values. The effects of damping and asymmetric end skirts on natural vibration frequency were also considered. The analytical frequencies of an idealized full scale space shuttle solid rocket boosted structure are computed with and without internal pressure and are compared with the 1/8 scale model results.

Leadbetter, S. A.↗
NASA NTRS1975

TC-2 post Helios experiment data review

Data are presented from a systems postflight analysis of the Centaur Launch Vehicle and Helios. Also given is a comparison of data from preflight analyses. Topics examined are: (1) propellant behavior; (2) helium usage; (3) propellant tank pressurization; (4) propellant tank thermodynamics; (5) component heating; thermal control; and thermal protection system; (6) main engine system; (7) H2O2 consumption; (8) boost pump post-meco performance; and (9) an overview of other systems.

Source record↗
NASA NTRS1976

Stability and control characteristics of an air-breathing missile configuration having a forward located inlet

An investigation was made to determine the aerodynamic characteristics of an airbreathing missile configuration having a forward located inlet. Control was provided by cruciform tail surfaces. Aerodynamic data were obtained for the body-tail configuration alone and with planar or cruciform wings. At Mach numbers from 2.86 to 4.63, the model had internal flow. At Mach numbers from 1.70 to 2.86, the internal duct was closed, and an inlet fairing was installed to simulate boost conditions.

Sawyer, W. C.↗
NASA NTRS1976

Results of test IA137 in the NASA/ARC 14 foot transonic wind tunnel of the 0.07 scale external tank forebody (model 68-T) to determine auxiliary aerodynamic data system feasibility

Tests were conducted in a 14 foot transonic wind tunnel to examine the feasibility of the auxiliary aerodynamic data system (AADS) for determining angles of attack and sideslip during boost flight. The model used was a 0.07 scale replica of the external tank forebody consisting of the nose portion and a 60 inch (full scale) cylindrical section of the ogive cylinder tangency point. The model terminated in a blunt base with a 320.0 inch diameter at external tank (ET) station 1120.37. Pressure data were obtained from five pressure orifices (one total and four statics) on the nose probe, and sixteen surface static pressure orifices along the ET forebody.

Thornton, D. E.↗
NASA NTRS1976

Space shuttle digital flight control system

The space shuttle digital, fly by wire, flight control system presents an interesting challenge in avionics system design. In residence in each of four redundant general purpose computers at lift off are the guidance, navigation, and control algorithms for the entire flight. The mission is divided into several flight segments: first stage ascent, second stage ascent; abort to launch site, abort once around; on orbit operations, entry, terminal area energy management; and approach and landing. The FCS is complicated in that it must perform the functions to fly the shuttle as a boost vehicle, as a spacecraft, as a reentry vehicle, and as a conventional aircraft. The crew is provided with both manual and automatic modes of operations in all flight phases including touchdown and rollout.

Minott, G. M.↗
NASA NTRS1975

Shuttle-launched multi-comet mission 1985

A low-cost multi-comet intercept mission with a launch in March 1985 is proposed. Two cometary spacecraft of identical design will be placed into a low earth parking orbit using a single Shuttle launch vehicle. Solid kick stages will then be used to boost each spacecraft into its required interplanetary trajectory. It is planned to have one spacecraft intercept comet Giacobini-Zinner in September 1985 and then go on to comet Borrelly with an encounter in December 1987. Earth swingby maneuvers will be used to achieve the double cometary intercept. The other spacecraft will be targeted for a pre-perihelion encounter with Halley's comet in December 1985.

Farquhar, R. W.↗