Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ASH CONTENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

A survey study on arsenic speciation in coal fly ash and insights into the role of coal combustion conditions

Coal fly ashes (CFAs) are the low-density byproducts of the coal combustion process. Improper or uncontrolled CFA disposal poses significant environmental and health concerns due to the potential leaching of toxic heavy metals such as arsenic (As). Previous studies have investigated the content and speciation of As in different CFA samples, yet systematic information on As speciation in CFA with representative coal source and combustion conditions is still missing. Based on a recent survey study on the typical coal sources and combustion conditions across the U.S., this study selected 19 representative CFA samples to systematically investigate As speciation and potential correlations with these parameters. The composition, morphology, mineralogy, and As speciation of these CFA samples were characterized by complementary analytical, microscopic, and spectroscopic techniques. Synchrotron X-ray spectroscopy and microscopy analyses revealed the dominant As oxidation state to be As(V) and with strong associations to Ca, with the exception of 3 samples that had 19–51% As(III), likely due to the use of selective catalytic reduction (SCR) process. Principal component analysis was conducted to identify potential correlations of As concentration and oxidation state with parameters such as major element content, loss on ignition (LOI), average particle size, coal source, and combustion condition. Al 2 O 3 and FeO content were found to capture a majority of the variability. Further, results from this study provide fundamental basis for understanding the correlations between coal source, combustion conditions, CFA characteristics, and As speciation, and providing insights for downstream beneficial utilization or disposal management.

01 COAL, LIGNITE, AND PEAT↗

Quantification of the degree of reaction of fly ash

The quantification of the fly ash (FA) in FA blended cements is an important parameter to understand the effect of the fly ash on the hydration of OPC and on the microstructural development. The FA reaction in two different blended OPC-FA systems was studied using a selective dissolution technique based on EDTA/NaOH, diluted NaOH solution, the portlandite content and by backscattered electron image analysis. The amount of FA determined by selective dissolution using EDTA/NaOH is found to be associated with a significant possible error as different assumptions lead to large differences in the estimate of FA reacted. In addition, at longer hydration times, the reaction of the FA is underestimated by this method due to the presence of non-dissolved hydrates and MgO rich particles. The dissolution of FA in diluted NaOH solution agreed during the first days well with the dissolution as observed by image analysis. At 28 days and longer, the formation of hydrates in the diluted solutions leads to an underestimation. Image analysis appears to give consistent results and to be most reliable technique studied.

36 MATERIALS SCIENCE↗

A study of the relationship between mineral content and mechanical properties of turkey gastrocnemius tendon

The vertebrate skeletal system undergoes adaptation in response to external forces, but the relation between the skeletal changes and such forces is not understood. In this context, the variation in the amount and location of calcification has been compared with changes in mechanical properties of the normally mineralizing turkey gastrocnemius tendon using ash weight measurements, X-ray radiography, and mechanical testing. Radiographic evidence from 12- to 17-week-old birds showed calcification in only portions of gastrocnemius tendons proximal to the tarsometatarsal joint. Mechanical testing of these dissected proximal regions demonstrated an increased ultimate stress and modulus and a decreased maximum strain that appeared to parallel calcification. Further, stress-strain curves of portions of uncalcified turkey gastrocnemius tendon were shaped similar to those of other typical unmineralized tendon curves while highly calcified tendons yielded curves resembling those of bone. The proximal portions of the gastrocnemius where mineralization begins were observed to have a decreased tendon cross-sectional area compared with distal portions which do not mineralize. Based on the resultant measures of mineral content and location and mechanical properties, it is hypothesized that increased calcification is a result of increased stresses at certain locations of the tendon, perhaps the consequence of the natural forces exerted by the large leg muscles of the bird into which the gastrocnemius inserts. More specifically, tendon calcification may be the result of stress-induced exposure of charged sites on the surfaces of collagen molecules, fibrils, or fibers so that deposition of mineral and subsequent mechanical reinforcement occur in the tissue.(ABSTRACT TRUNCATED AT 250 WORDS).

Non-NASA Center↗

Mechanical properties and durability performance of concretes with Limestone Calcined Clay Cement (LC3)

The adoption of any binder system for structural concrete depends on the performance characteristics desired for addressing the long-term deformation and durability concerns. The major properties influencing the performance includes the shrinkage characteristics governing the long-term deformation, and durability characteristics related to various transport mechanisms, governing the performance in different service conditions. This paper describes the potential of Limestone Calcined Clay Cement (LC{sup 3}) for use in structural concrete in comparison with Ordinary Portland Cement (OPC) and fly ash based blended cement (FA30). Three types of concrete mixtures were designed for the study, two based on achieving an equivalent strength grade (M30 and M50 concrete grade) with each binder, and the third with equal binder content and w/b ratio. Mechanical properties such as compressive strength and elastic modulus, and autogenous and drying shrinkage, along with various durability parameters of the different concretes were assessed. Oxygen permeability, rapid chloride penetration, chloride migration, resistivity development and water sorptivity were the various parameters considered for evaluation of durability performance. The results indicate the superiority of LC{sup 3} binder over other binders in producing durable concrete, especially in a chloride laden environment. The major reason for the better performance was attributed to the more compact and dense microstructure of the system with the LC{sup 3} binder against OPC and FA30. The drying shrinkage performance was seen to be similar for concrete with all three binders.

36 MATERIALS SCIENCE↗

Overhead Protection Increases Fuel Quality and Natural Drying of Leaf-On Woody Biomass Storage Piles

Short-rotation woody crops (SRWC) have the potential to make substantial contributions to the supply of biomass feedstock for the production of biofuels and bioproducts. This study evaluated changes in the fuel quality (moisture, ash, and heating value) of stored spring harvested shrub willow (Salix spp.) and hybrid poplar (Populus spp.) chips with respect to pile protection treatments, location within the storage piles, and length of storage. Leaf-on willow and poplar were harvested in the spring, and wood chips and foliage with moisture content in the range of 42.1% to 49.9% (w.b.) were stored in piles for five months, from May to October 2016. Three protection treatments were randomly assigned to the piles. The control treatment had no cover (NC), so piles were exposed to direct solar radiation and rainfall. The second treatment had a canopy (C) installed above the piles to limit direct rainfall. The final treatment had a canopy plus a dome aeration system (CD) installed over the piles. Covering piles reduced and maintained the low moisture content in wood chip piles. Within 30 days of establishment, the moisture content in the core of the C pile decreased to less than 30%, and was maintained between 24%–26% until the end of the storage period. Conversely, the moisture content in the NC piles decreased in the first two months, but then increased to the original moisture content in the core (>45 cm deep) and up to 70% of the original moisture content in the shell (<45 cm deep). For all the treatments in the tested conditions, the core material dried faster than the shell material. The higher heating value (HHV) across all the treatments increased slightly from 18.31 ± 0.06 MJ/kg at harvest to 18.76 ± 0.21 MJ/kg at the end of the storage period. The lower heating value (LHV) increased by about 50% in the C and CD piles by the end of the storage period. However, in the NC piles, the LHV decreased by 3% in the core and 52% in the shell. Leaf-on SRWC biomass stored in piles created in late spring under climatic conditions in central and northern New York showed differing moisture contents when stored for over 60–90 days. Overhead protection could be used to preserve or improve the fuel quality in terms of the moisture content and heating value if more than two months of storage are required. However, the implementation of such management practice will depend on whether the end users are willing to pay a higher price for dryer biomass and biomass with a higher LHV.

54 ENVIRONMENTAL SCIENCES↗

Petrogenesis of Challis volcanics from central and southwestern Idaho - Trace element and Pb isotopic evidence

An analysis of the lava flows and ash-flow tuffs in Idaho is conducted to determine the composition of the volcanics in terms of major and trace elements and Pb isotopic substances. Al2O3 is found to be low, MgO content is high, and the concentration of K2O is higher or equal to that of Na2O with respect to the lavas of mafic to intermediate composition. Trace elements and element ratios are compatible with the crustal component, and the Pb isotopic compositions suggest a lack of assimilation during crystallization. The evidence does not support the notion of a magma system related to subduction, and the data regarding Pb isotopes and trace elements point to a connection with the lithosphere. A model is proposed for the Challis volcanics in which they resulted from completely melting within the lithosphere and then extending during the late Mesozoic and early Cenozoic compression.

Norman, Marc D.↗

Calcium citrate without aluminum antacids does not cause aluminum retention in patients with functioning kidneys

It has been suggested that calcium citrate might enhance aluminum absorption from food, posing a threat of aluminum toxicity even in patients with normal renal function. We therefore measured serum and urinary aluminum before and following calcium citrate therapy in patients with moderate renal failure and in normal subjects maintained on constant metabolic diets with known aluminum content (967-1034 mumol/day, or 26.1-27.9 mg/day, in patients and either 834 or 1579 mumol/day, or 22.5 and 42.6 mg/day, in normal subjects). Seven patients with moderate renal failure (endogenous creatinine clearance of 43 ml/min) took 50 mmol (2 g) calcium/day as effervescent calcium citrate with meals for 17 days. Eight normal women received 25 mmol (1 g) calcium/day as tricalcium dicitrate tablets with meals for 7 days. In patients with moderate renal failure, serum and urinary aluminum were normal before treatment at 489 +/- 293 SD nmol/l (13.2 +/- 7.9 micrograms/l) and 767 +/- 497 nmol/day (20.7 +/- 13.4 micrograms/day), respectively. They remained within normal limits and did not change significantly during calcium citrate treatment (400 +/- 148 nmol/l and 600 +/- 441 nmol/day, respectively). Similarly, no significant change in serum and urinary aluminum was detected in normal women during calcium citrate administration (271 +/- 59 vs 293 +/- 85 nmol/l and 515 +/- 138 vs 615 +/- 170 nmol/day, respectively). In addition, skeletal bone aluminum content did not change significantly in 14 osteoporotic patients (endogenous creatinine clearance of 68.5 ml/min) treated for 24 months with calcium citrate, 10 mmol calcium twice/day separately from meals (29.3 +/- 13.9 ng/mg ash bone to 27.9 +/0- 10.4, P = 0.727). In them, histomorphometric examination did not show any evidence of mineralization defect. Thus, calcium citrate given alone without aluminum-containing drugs does not pose a risk of aluminum toxicity in subjects with normal or functioning kidneys, when it is administered on an empty stomach at a recommended dose of 20 mmol calcium/day.

Non-NASA Center↗

An Investigation of Carburization Behavior of Molten Iron for the Flash Ironmaking Process

In order to recognize the dripping and the carburizing behaviors of the molten iron within the coke packed bed in the flash ironmaking process, a transient three-dimensional numerical model was developed. The volume of fluid (VOF) approach is used to describe the movement of the molten iron and the argon gas. The porous medium module is employed to define the momentum, heat, and mass transfer between the coke packed bed and the molten iron. Moreover, a factor is introduced to consider the influence of the ash film on the carburization process. A reasonable agreement between the experiment and simulation is obtained. The results indicate that the molten iron flows downward from the upper crucible to middle crucible. After entering the middle crucible, the molten iron spreads around within the coke packed bed and simultaneously moves downward. The carbon is, therefore, transferred from the coke to the molten iron. With the 47-mm-height coke packed bed, the carbon content in the molten iron after the carburization decreases from 3.19 to 1.97 pct, while the coke diameter ranges from 2 to 5 mm. With the 2-mm-diameter coke, the carbon content in the molten iron after the carburization increases from 2.84 to 4.81 pct, while the coke packed bed height increases from 37 to 97 mm.

36 MATERIALS SCIENCE↗

Hydration studies of calcium sulfoaluminate cements blended with fly ash

The main objective of this work is to study the hydration and properties of calcium sulfoaluminate cement pastes blended with fly ash (FA) and the corresponding mortars at different hydration ages. Laboratory X-ray powder diffraction, rheological studies, thermal analysis, porosimetry and compressive strength measurements were performed. The analysis of the diffraction data by Rietveld method allowed quantifying crystalline phases and overall amorphous contents. The studied parameters were: i) FA content, 0, 15 and 30 wt.%; and ii) water addition, water-to-CSA mass ratio (w/CSA = 0.50 and 0.65), and water-to-binder mass ratio (w/b = 0.50). Finally, compressive strengths after 6 months of 0 and 15 wt.% FA [w/CSA = 0.50] mortars were similar: 73 ± 2 and 72 ± 3 MPa, respectively. This is justified by the filler effect of the FA as no strong evidences of reactivity of FA with CSA were observed. These results support the partial substitution of CSA cements with FA with the economic and environmental benefits.

36 MATERIALS SCIENCE↗

Elemental Modes of Occurrence in an Illinois #6 Coal and Fractions Prepared by Physical Separation Techniques at a Coal Preparation Plant

In order to gain better insight into elemental partitioning between clean coal and tailings, modes of occurrence have been determined for a number of major and trace elements (S, K, Ca, V, Cr, Mn, Fe, Zn, As, Se, Pb) in an Illinois No.6 coal and fractions prepared by physical separation methods at a commercial coal preparation plant. Elemental modes of occurrence were largely determined directly by XAFS or Moessbauer spectroscopic methods because the concentrations of major minerals and wt.% ash were found to be highly correlated for this coal and derived fractions, rendering correlations between individual elements and minerals ambiguous for inferring elemental modes of occurrence. Of the major elements investigated, iron and potassium are shown to be entirely inorganic in occurrence. Most (90%) of the iron is present as pyrite, with minor fractions in the form of clays and sulfates. All potassium is present in illitic clays. Calcium in the original coal is 80-90% inorganic and is divided between calcite, gypsum, and illite, with the remainder of the calcium present as carboxyl-bound calcium. In the clean coal fraction, organically associated Ca exceeds 50% of the total calcium. This organically-associated form of Ca explains the poorer separation of Ca relative to both K and ash. Among the trace elements, V and Cr are predominantly inorganically associated with illite, but minor amounts (5-15% Cr, 20-30% V) of these elements are also organically associated. Estimates of the V and Cr contents of illite are 420 ppm and 630 ppm, respectively, whereas these elements average 20 and 8 ppm in the macerals. Arsenic in the coal is almost entirely associated with pyrite, with an average As content of about 150 ppm, but some As ({approx} 10%) is present as arsenate due to minor oxidation of the pyrite. The mode of occurrence of Zn, although entirely inorganic, is more complex than normally noted for Illinois basin coals; about 2/3 is present in sphalerite, with lesser amounts associated with illite and a third form yet to be conclusively identified. The non-sulfide zinc forms are removed predominantly by the first stage of separation (rotary breaker), whereas the sphalerite is removed by the second stage (heavy media). Germanium is the only trace element determined to have a predominantly organic association.

01 COAL, LIGNITE, AND PEAT↗

Concentration of rare earth minerals from coal by froth flotation

Rare earth elements (REEs) found in coal are in the form of minerals, ion-adsorbed onto clay surfaces or inner layers, or organically bound. Rare earth minerals such as monazite exist in coal and have grain sizes smaller than 5 µm. In this study, froth flotation was successful in concentrating rare earth minerals existing in a thickener underflow material derived from Fire Clay seam coal that contained around 431 ppm of total rare earth elements (TREE) on a dry ash basis. Furthermore, conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2,300 ppm TREE. Using a laboratory flotation column to limit hydraulic entrainment, the TREE content was further enriched to around 4,700 ppm, which equated to an enrichment ratio of 10:1.

01 COAL, LIGNITE, AND PEAT↗

Performance Testing of Moving Bed Gasifier Using Biomass and Waste Fuels to Generate Low-Cost Clean Hydrogen

Our need for hydrogen is growing as the world transitions toward a low-carbon future. Hydrogen provides long-term energy storage for grid stability in a solar- and wind-dominated power market and can be used to decarbonize other sectors. One promising process for generating low-cost hydrogen that produces net-negative carbon is to gasify biomass with a mixture of legacy coal wastes, waste plastics, and other wastes with carbon capture. Use of waste fuels lowers costs and diverts waste from landfills. EPRI is leading a project, funded by the U.S. Department of Energy, to conduct performance testing of modular, moving-bed gasification for the generation of low-cost, clean hydrogen from biomass mixed with legacy coal waste, waste plastic, and/or refuse derived fuels. The work scope includes preparation of multiple pellet feedstocks using biomass (both woody biomass and corn stover) with a mixture of legacy coal waste, plastic waste (wire insulation), and refuse-derived fuel (RDF). These pelletized feedstocks are being qualified based on performance testing of selected fuel blend compositions in updraft moving-bed gasifier located in Sardinia, Italy. Testing is being conducted to obtain relevant data to advance the modular design of the moving-bed gasification process, and successfully use these feedstocks to produce a high hydrogen content raw syngas that can be shifted to produce clean hydrogen. Testing results will be used to determine the effects of the various fuels on feedstock development, the resulting products (i.e., syngas compositions, organic condensate production, and ash characteristics), and impacts on gasifier operations.

08 HYDROGEN↗

Coal-Waste-Enhanced Filaments for Additive Manufacturing of High-Temperature Plastics and Ceramic Composites

In the United States, coal waste from over a century of mining and burning coal for heat and electricity has accumulated as mountains of coal fly ash and bottom ash and acre-size ponds, coal fines and gob. These materials can be a problem for local communities and water systems. A cost-effective process to utilize high volumes of these coal wastes in a high-value product would be beneficial to those communities by reducing the amount of waste and providing jobs, manufacturing components, and materials from the waste. Many coal-to-products technologies (e.g., carbon fibers, graphene, carbon foam) rely on carefully choosing the starting material and then altering it chemically or thermally to make the products work. Due to the wide variability of composition and coal content in typical coal waste streams, many high-volume coal waste streams are likely to be unsuitable for use in those technologies. Semplastics’ technology has been shown to utilize most types of coal waste successfully without any pre-selection or pre-processing requirements other than a nominal particle-size reduction for wastes like bottom ash. This characteristic of Semplastics’ solution may enable the use of much larger volumes of a wider range of coal wastes than other coal-to-products technologies. In this project, Semplastics leveraged its unique experience with both coal waste (fly ash or coal combustion residuals), resin materials, and 3D printing to develop 3D printer filaments using common coal wastes – bituminous coal fines and fly ash – and researched the feasibility of using other forms of coal waste as fillers. Simple 3D-printed parts were successfully produced from the coal waste enhanced filaments, which were found to have improved strength and stiffness.

01 COAL, LIGNITE, AND PEAT↗

Efficiency of natural pozzolans, ground glasses and coal bottom ashes in mitigating sulfate attack and alkali-silica reaction

The use of pozzolans to partially replace Portland cement in concrete has generally demonstrated beneficial impacts on the durability characteristics of concrete for decades. In this paper a diverse range of pozzolans including natural pozzolans, ground glasses and industrial by-products such as coal ash (fly ash and bottom ash) and silica fume were investigated for their synergistic potential in binary or ternary blends with Portland cement in improving resistance to chemical sulfate attack and alkali-silica reaction (ASR). It is generally considered that pozzolans improve most of the durability issues encountered in concrete, including reducing the risk of sulfate attack or ASR. But this is not always the case. For example, it was found that ground glasses were very efficient in improving sulfate resistance, but their ability to mitigate expansion due to ASR was dictated by the equivalent alkalis content (Na{sub 2}O{sub e}) of the glass and high-alkali soda glass was generally not effective in this role. On the other hand, metakaolin, a highly reactive pozzolan, was highly effective in reducing ASR expansion, but may actually increase the damage due to sulfate attack when used at moderate replacement levels. Most pozzolans, such as low-CaO coal fly ash and ground coal bottom ash, silica fume, and pumice, were effective in controlling expansion due to both ASR and sulfate attack. The results demonstrated that the extent of the positive impact of using natural pozzolans on both properties was variable. The pozzolanic reactivity of materials alone was an unreliable indicator to assess the ability of the pozzolan to suppress expansion due to sulfate attack or ASR.

36 MATERIALS SCIENCE↗

Material analysis of Bottom ash from waste-to-energy plants

Bottom ash (BA) from waste-to-energy (WtE) plants contains valuable components, particularly ferrous (Fe) and non-ferrous (NFe) metals, which can be recovered. To assess the resource recovery potential of BA in the Czech Republic, it was necessary to obtain its detailed material composition. This paper presents the material composition of BA samples from all three Czech WtE plants. It was found that the BA contained 9.2–22.7% glass, 1.8–5.1% ceramics and porcelain, 0.2–1.0% unburnt organic matter, 10.2–16.3% magnetic fraction, 6.1–11.0% Fe scrap, and 1.3–2.8% NFe metals (in dry matter). The contents of individual components were also studied with respect to the BA granulometry and character of the WtE waste collection area.

54 ENVIRONMENTAL SCIENCES↗

Skeletal status and soft tissue composition in astronauts. Tissue and fluid changes by radionuclide absorptiometry in vivo

A device has been constructed and tested which provides immediate readout of bone mineral content and bone width from absorptiometric scans with low energy radionuclides. The basis of this analog system is a logarithmic converter-integrator coupled with a precision linear ratemeter. The system provided accurate and reliable results on standards and ashed bone sections. Clinical measurements were made on about 100 patients with the direct readout system, and these were highly correlated with the results from digital scan data on the same patients. The direct readout system has been used successfully in field studies and surveys as well as for clinical observations.

Cameron, J. R.↗

Explosive volcanism on Hecates Tholus, Mars - Investigation of eruption conditions

From a reexamination of the medium and high-resolution Viking images of Amazonian and Hesperian age volcanic centers on Mars, it is believed that an excellent example of well-preserved explosive activity does indeed exist close to the summit of Hecates Tholus. A mantled region to the west of the summit caldera is seen as an example of a geologically very recent plinian air fall ash deposit. Morphological evidence is presented for describing this as explosively generated material, and numerical models of magma ascent and eruption in the Martian environment are used to estimate the physical characteristics (eruption cloud height, magma discharge rate, magma volatile content, duration of activity, and vent size) for this event. Attention is also given to the implication of this eruptive style for the composition of the erupted magma.

Mouginis-Mark, P. J.↗

Investigation of coal char-slag transition during oxidation: effect of temperature and residual carbon

The transition of coal char to molten slag at high conversion was studied for a bituminous coal using a laminar entrained-flow reactor under oxidizing conditions. Post-oxidized char particles were analyzed by various techniques including loss-on-ignition, gas adsorption analysis, and scanning electron microscopy to determine carbon content, internal surface area and pore size distribution, and char morphology, respectively. These analyses provide information concerning the effect of temperature and residual carbon on the transition from porous char to molten slag. Results showed that, at temperatures above the ash flow temperature, the transition from porous char to molten slag occurred at about 90% conversion for the coal used in this study. No transition occurred at temperatures below the ash flow temperature. This finding explains previous observations that there is a coal-dependent critical carbon conversion at which the ash stickiness increases dramatically. This result also indicates that surface area can be used as a criterion for determining the critical conversion of the transition. In addition, it was found that the randomly overlapping pore model cannot be directly applied to predict the surface area evolution of char particles during the transition without considering the reopening of closed micropores during the initial reaction and the ash fusion effect. 33 refs., 9 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗