Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIRPLANES - STRENGTH CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Correlation of Full-Scale Isolated Proprotor Performance and Loads

A full-scale isolated proprotor test was recently conducted in the USAF National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center. The test article was a 3-bladed research rotor derived from the right-hand rotor of the AW609. For this test, the NASA Tiltrotor Test Rig (TTR) and rotor were installed in the 40- by 80-foot test section. This paper presents correlations between data and predictions of rotor performance and blade moments using the newly acquired test data and the comprehensive analysis CAMRAD II. The operational conditions covered in this analytical study are: hover (actually, low speed vertical climb), cruise (airplane mode), conversion, and helicopter mode. Mean and 1/2 peak-to-peak quantities (hpp) are correlated; time-history correlation for the helicopter condition is also included. The correlation is reasonable to good. Also, the hover calculations turned out to be useful in providing reality checks on the test hardware such as: a) the functioning of the blade strain gages and b) calibration of the measurement of the collective pitch hardware. The time-history correlation shows that, compared to the rolled-up wake model, the multiple-trailer wake model improves the correlation slightly; the longitudinal cyclic correlation is reasonable but the lateral cyclic correlation is not good, and the collective is predicted well by the rolled-up wake model; the flap moment correlation is reasonable; the pitch link load and lag moment are underpredicted; and the torsion moment correlation is poor and needs further study.

Kottapalli, Sesi↗
NASA NTRS1992

Thrust stand evaluation of engine performance improvement algorithms in an F-15 airplane

Results are presented from the evaluation of the performance seeking control (PSC) optimization algorithm developed by Smith et al. (1990) for F-15 aircraft, which optimizes the quasi-steady-state performance of an F100 derivative turbofan engine for several modes of operation. The PSC algorithm uses onboard software engine model that calculates thrust, stall margin, and other unmeasured variables for use in the optimization. Comparisons are presented between the load cell measurements, PSC onboard model thrust calculations, and posttest state variable model computations. Actual performance improvements using the PSC algorithm are presented for its various modes. The results of using PSC algorithm are compared with similar test case results using the HIDEC algorithm.

Conners, Timothy R.↗
NASA NTRS1987

Three-dimensional trajectory analyses of two drop sizing instruments - PMS OAP and PMS FSSP

Flow-induced distortions of water drop fluxes and speeds as seen by the PMS optical array probe (OAP) and the PMS forward scattering spectrometer probe (FSSP) are estimated via three-dimensional flow and trajectory calculation methods. The sensitivities of the instruments to water drop diameter, angle of attack, and free stream air speed are determined. The instruments are first placed in isolation and then mounted under the wing of a Twin Otter airplane. For the wing-mounted OAP at 4-deg angle of attack, partial flow stagnation under the uptilted wing causes a significant decrease in both the flux and speed for small water drops. For the wing-mounted FSSP, sensitivity is found to both angle of attack and free stream air speed.

Norment, H. G.↗
NASA NTRS1957

Cloud-Droplet Ingestion in Engine Inlets with Inlet Velocity Ratios of 1.0 and 0.7

The paths of cloud droplets into two engine inlets have been calculated for a wide range of meteorological and flight conditions. The amount of water in droplet form ingested by the inlets and the amount and distribution of water impinging on the inlet walls are obtained from these droplet-trajectory calculations. In both types of inlet, a prolate ellipsoid of revolution represents either part or all of the forebody at the center of an annular inlet to an engine. The configurations can also represent a fuselage of an airplane with side ram-scoop inlets. The studies were made at an angle of attack of 0 degree. The principal difference between the two inlets studied is that the inlet-air velocity of one is 0.7 that of the other. The studies of the two velocity ratios lead to some important general concepts of water ingestion in inlets.

Brun, Rinaldo J↗
NASA NTRS2000

Shipboard Sunphotometer Measurements of Aerosol Optical Depth Spectra and Columnar Water Vapor During ACE-2 and Comparison with Selected Land, Ship, Aircraft, and Satellite Measurements

Analyses of aerosol optical depth (AOD) and colurnmn water vapor (CWV) measurements acquired with NASA Ames Research Center's 6-channel Airborne Tracking Sunphotometer (AATS-6) operated aboard the R/V Professor Vodyanitskiy during the 2nd Aerosol Characterization Experiment (ACE-2) are discussed. Data are compared with various in situ and remote measurements for selected cases. The focus is on 10 July, when the Pelican airplane flew within 70 km of the ship near the time of a NOAA-14/AVHRR satellite overpass and AOD measurements with the 14-channel Ames Airborne Tracking Sunphotometer (AATS-14) above the marine boundary layer (MBL) permitted calculation of AOD within the MBL from the AATS-6 measurements. A detailed column closure test is performed for MBL AOD on 10 July by comparing the AATS-6 MBL AODs with corresponding values calculated by combining shipboard particle size distribution measurements with models of hygroscopic growth and radiosonde humidity profiles (plus assumptions on the vertical profile of the dry particle size distribution and composition). Large differences (30-80% in the mid-visible) between measured and reconstructed AODs are obtained, in large part because of the high sensitivity of the closure methodology to hygroscopic growth models, which vary considerably and have not been validated over the necessary range of particle size/composition distributions. The wavelength dependence of AATS-6 AODs is compared with the corresponding dependence of aerosol extinction calculated from shipboard measurements of aerosol size distribution and of total scattering mearured by a shipboard integrating nephelometer for several days. Results are highly variable, illustrating further the great difficulty of deriving column values from point measurements. AATS-6 CWV values are shown to agree well with corresponding values derived from radiosonde measurements during 8 soundings on 7 days and also with values calculated from measurements taken on 10 July with the AATS-14 and the University of Washington Passive Humidigraph aboard the Pelican.

Livingston, John M.↗
NASA NTRS2009

Damage Arresting Composites for Shaped Vehicles

This report describes the development of a novel structural solution that addresses the demanding fuselage loading requirements for the Hybrid Wing or Blended Wing Body configurations that are described in NASA NRA subtopic A2A.3, "Materials and Structures for Wing Components and Non-Circular Fuselage." The phase I portion of this task includes a comprehensive finite element model-based structural sizing exercise performed using the BWB airplane configuration to generate internal loads and fuselage panel weights for an advanced Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) structural concept. An accompanying element-level test program is also described which substantiates the analytical results and calculation methods used in the trade study. The phase II plan for the continuation of this research is also included herein.

Velicki, Alex↗
NASA NTRS1983

Performance of high-altitude, long-endurance, turboprop airplanes using conventional or cryogenic fuels

An analytical study has been conducted to evaluate the potential endurance of remotely piloted, low speed, high altitude, long endurance airplanes designed with 1990 technology. The baseline configuration was a propeller driven, sailplane like airplane powered by turbine engines that used JP-7, liquid methane, or liquid hydrogen as fuel. Endurance was measured as the time spent between 60,000 feet and an engine limited maximum altitude of 70,000 feet. Performance was calculated for a baseline vehicle and for configurations derived by varying aerodynamic, structural or propulsion parameters. Endurance is maximized by reducing wing loading and engine size. The level of maximum endurance for a given wing loading is virtually the same for all three fuels. Constraints due to winds aloft and propulsion system scaling produce maximum endurance values of 71 hours for JP-7 fuel, 70 hours for liquid methane, and 65 hours for liquid hydrogen. Endurance is shown to be strongly effected by structural weight fraction, specific fuel consumption, and fuel load. Listings of the computer program used in this study and sample cases are included in the report.

Liu, G. C.↗
NASA NTRS1957

Comparison of calculated and experimental load distributions on thin wings at high subsonic and sonic speeds

A method for calculating the aerodynamic loading on a wing in combination with a body is presented. Calculated results are compared with experimentally measured data for two wing-body configurations throughout a range of Mach number up to 1.0. The magnitude and the distribution of spanwise loading of the calculated data are generally in good agreement with the experimental data.

WINGS, COMPLETE - THEORY↗
NASA NTRS1978

A finite volume method for calculating transonic potential flow around wings from the pressure minimum integral

Analysis of the pressure minimum integral in the calculation of three-dimensional potential flow around wings makes it possible to use non-rectangular mesh networks for distributing the three-dimensional potential into discrete points. The method is comparatively easily expanded to the treatment of realistic airplane configurations. Shock-pressure affected pressure distributions on any wings are determined with accuracy using this method.

Eberle, A.↗
NASA NTRS1981

Analytical study of the cruise performance of a class of remotely piloted, microwave-powered, high-altitude airplane platforms

Each cycle of the flight profile consists of climb while the vehicle is tracked and powered by a microwave beam, followed by gliding flight back to a minimum altitude. Parameter variations were used to define the effects of changes in the characteristics of the airplane aerodynamics, the power transmission systems, the propulsion system, and winds. Results show that wind effects limit the reduction of wing loading and increase the lift coefficient, two effective ways to obtain longer range and endurance for each flight cycle. Calculated climb performance showed strong sensitivity to some power and propulsion parameters. A simplified method of computing gliding endurance was developed.

Morris, C. E. K., Jr.↗
NASA NTRS1985

Finding Bright-Spot Coordinates in Television Images

Circuit provides data for computer to calculate coordinates of bright spot of light in video image. Calculation performed while image being scanned, and results available immediately at end of video frame. Video-processing circuit has variety of potential uses in commerce and industry. For example, locates tagged-parts on factory assembly line or track airplane landing lights.

Richardson, T. E.↗
NASA NTRS1943

A theoretical investigation of the lateral oscillations of an airplane with free rudder with special reference to the effect of friction

Charts showing the variation in dynamic stability with the rudder hinge-moment characteristics are presented. A stabilizing rudder floating tendency combined with a high degree of aerodynamic balance is shown to lead to oscillations of increasing amplitude. This dynamic instability is increased by viscous-friction in the rudder control system. The presence of solid friction in the rudder control system will cause steady oscillations of constant amplitude if the floating angle of the rudder per unit angle of sideslip is stabilizing and greater than a certain critical value that depends on other airplane parameters, such as vertical-tail area and airplane moment of inertia about the vertical axis. The amplitude of the steady oscillation is proportional to the amount of friction and is generally quite small but increases as the condition of dynamic instability is approached. An approximate method of calculating the amplitudes of the steady oscillation is explained and is illustrated by a numerical example. A more accurate step-by-step calculation of the motion is also made and it is shown that the agreement with the approximate method is good.

Greenberg, Harry↗
NASA NTRS1956

High-temperature oxidation and ignition of metals

A study of the high-temperature oxidation of several aircraft construction materials was undertaken to assess the possibility of ignition under high-temperature flight conditions.Tests have been made both in open and closed jets, and, in addition, the burning of metals has been observed under static conditions in a pressurized vessel containing either air, oxygen, or nitrogen. When heated in an atmosphere of oxygen or when heated and plunged into a supersonic airstream, titanium, iron, carbon steel, and common alloys such as 4130 were found to have spontaneous-ignition temperatures in the solid phase (below melting) and they melted rapidly while burning. Inconel, copper, 18-8 stainless steel, Monel, and aluminum could not be made to ignite spontaneously at temperatures up to melting with the equipment available. Magnesium ignited spontaneously in either type of test at temperatures just above the melting temperature.A theory for the spontaneous ignition of metals, based on the first law of thermodynamics, is presented. Good correlation was obtained between calculated spontaneous-ignition temperatures and values measured in supersonic jet tests. There appears at the present time to be no need for concern regarding the spontaneous ignition of Inconel, the stainless steels, copper, aluminum, or magnesium for ordinary supersonic airplane or missile applications where the material temperature is kept within ordinary structural limits or at least below melting. For hypersonic applications where the material is to be melted away to absorb the heat of convection, the results of the present tests do not apply sufficiently to allow a conclusion.

Hill, Paul R↗
NASA NTRS2011

Subsonic Ultra Green Aircraft Research

This Final Report summarizes the work accomplished by the Boeing Subsonic Ultra Green Aircraft Research (SUGAR) team in Phase 1, which includes the time period of October 2008 through March 2010. The team consisted of Boeing Research and Technology, Boeing Commercial Airplanes, General Electric, and Georgia Tech. The team completed the development of a comprehensive future scenario for world-wide commercial aviation, selected baseline and advanced configurations for detailed study, generated technology suites for each configuration, conducted detailed performance analysis, calculated noise and emissions, assessed technology risks, and developed technology roadmaps. Five concepts were evaluated in detail: 2008 baseline, N+3 reference, N+3 high span strut braced wing, N+3 gas turbine battery electric concept, and N+3 hybrid wing body. A wide portfolio of technologies was identified to address the NASA N+3 goals. Significant improvements in air traffic management, aerodynamics, materials and structures, aircraft systems, propulsion, and acoustics are needed. Recommendations for Phase 2 concept and technology projects have been identified.

Bradley, Marty K.↗
NASA NTRS1973

Response of a rigid aircraft to nonstationary atmospheric turbulence.

The plunging response of an aircraft to a type of nonstationary turbulent excitation is considered. The latter consists of stationary Gaussian noise modulated by a well-defined envelope function. The intent of the investigation is to model the excitation experienced by an airplane flying through turbulence of varying intensity and to examine the influence of intensity variations on exceedance frequencies of the gust velocity and the airplane's plunging velocity and acceleration. One analytical advantage of the proposed model is that the Gaussian assumption for the gust excitation is retained. The analysis described herein is developed in terms of an envelope function of arbitrary form; however, numerical calculations are limited to the case of harmonic modulation.

Verdon, J. M.↗
NASA NTRS1981

Parametric study of microwave-powered high-altitude airplane platforms designed for linear flight

The performance of a class of remotely piloted, microwave powered, high altitude airplane platforms is studied. The first part of each cycle of the flight profile consists of climb while the vehicle is tracked and powered by a microwave beam; this is followed by gliding flight back to a minimum altitude above a microwave station and initiation of another cycle. Parametric variations were used to define the effects of changes in the characteristics of the airplane aerodynamics, the energy transmission systems, the propulsion system, and winds. Results show that wind effects limit the reduction of wing loading and the increase of lift coefficient, two effective ways to obtain longer range and endurance for each flight cycle. Calculated climb performance showed strong sensitivity to some power and propulsion parameters. A simplified method of computing gliding endurance was developed.

Morris, C. E. K., Jr.↗
NASA NTRS1934

A Comparison Between the Theoretical and Measured Longitudinal Stability Characteristics of an Airplane

This report covers an investigation of the application of the theory of dynamic longitudinal stability, based on the assumption of small oscillations, to oscillations an airplane is likely to undergo in flight. The investigation was conducted with a small parasol monoplane for the fixed-stick condition. The period and damping of longitudinal oscillations were determined by direct measurements of oscillations in flight and also by calculation in which the factors that enter the theoretical stability equation were determined in flight. A comparison of the above-mentioned characteristics obtained by these two methods indicates that the theory is applicable to the conditions encountered in flight.

Soule, Hartley A↗