Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yaw control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Study of aerodynamic technology for VSTOL fighter/attack aircraft: Horizontal attitude concept

A horizontal attitude VSTOL (HAVSTOL) supersonic fighter attack aircraft powered by RALS turbofan propulsion system is analyzed. Reaction control for subaerodynamic flight is obtained in pitch and yaw from the RALS and roll from wingtip jets powered by bleed air from the RALS duct. Emphasis is placed on the development of aerodynamic characteristics and the identification of aerodynamic uncertainties. A wind tunnel program is shown to resolve some of the uncertainties. Aerodynamic data developed are static characteristics about all axes, control effectiveness, drag, propulsion induced effects and reaction control characteristics.

Brown, S. H.↗
NASA NTRS1933

The Effects of Slots and Flaps on Lateral Control of a Low-wing Monoplane as Determined in Flight

This paper presents the results of flight tests made to determine the effect of slots and flaps on the lateral control of a low-wing monoplane. Maximum angular accelerations in roll and yaw produced by sudden application of the ailerons and maximum accelerations in yaw produced by sudden application of the rudder during gliding flight were recorded for the following wing arrangements: (a) no auxiliary device; (b) full-span slots; (c) plain flaps; (d) flaps and full-span slots; (e) wing-tip slots. Rolling- and yawing-moment coefficients were derived from the accelerations. The full span slots and the flaps each had about the same influence on the aileron rolling moments. At values of the lift coefficient obtainable with the plain wing, the effect of these devices was negligible. At the higher lift coefficients obtainable with these devices, the rolling-moment coefficients increased slightly but, despite this increase, the aileron effectiveness progressively decreased with increasing lift coefficient, owing to the corresponding reduction in air speed. In the range covered by the tests, the effectiveness of the controls was appreciably reduced by the wing-tip slots. The adverse yawing moment of the ailerons experienced at the large lift coefficients obtained with the flaps was appreciably less than at similar lift coefficients obtained with either full-span or wing-tip slots. The yawing moments produced by the rudder were only slightly affected by the use of the auxiliary devices. The airplane was found to be laterally unstable with all combinations tested. Because of the angular velocities acquired in the time taken to deflect the ailerons the rolling moments recorded in flight were only about two thirds the values that would have been obtained with the wing restrained as in wind-tunnel tests.

WING SLOTS↗
NASA NTRS1975

A study of pilot behavior during controlling the lateral directional motion of airplanes in turbulent air

The pilot behaviors controlling the lateral directional motion of airplanes in turbulent air have been investigated by using the pilot transfer function which has been obtained by the analysis of flight test data. The pilot uses the gains for the aileron manipulation proportionally to bank angle so as to minimize r.m.s. of bank angle. The pilot rudder manipulations are done proportionally to rolling velocity, yawing velocity, and yaw angle. Namely, the pilot carries out the cross control for the rudder.

Beppu, G.↗
NASA NTRS1992

Application of a passivity based control methodology for flexible joint robots to a simplified Space Shuttle RMS

A passivity approach for the control design of flexible joint robots is applied to the rate control of a three-link arm modeled after the shoulder yaw joint of the Space Shuttle Remote Manipulator System (RMS). The system model includes friction and elastic joint couplings modeled as nonlinear springs. The basic structure of the proposed controller is the sum of a model-based feedforward and a model-independent feedback. A regulator approach with link state feedback is employed to define the desired motor state. Passivity theory is used to design a motor state-based controller to stabilize the error system formed by the feedforward. Simulation results show that greatly improved performance was obtained by using the proposed controller over the existing RMS controller.

Sicard, Pierre↗
NASA NTRS1954

Stability and Control Flight Tests of a Vertically Rising Airplane Model Similar to the Lockheed XFV-1 Airplane

This paper presents the results of an investigation of the dynamic stability and controllability of a model which approximately represents the Lockheed XFV-1 airplane to a 1/8 scale. The investigation consisted of hovering flights in still air at a considerable height above the ground, hovering flights very close to the ground, vertical take-offs and landings, flights through the transition range from hovering to normal forward flight, and sideways translational flights. The model could be flown smoothly and easily in hovering flight despite the fact that the uncontrolled pitching and yawing motions were unstable oscillations. There was a noticeable reduction in the controllability of the model when hovered very close to the ground but take-offs could be made easily and landings on a g,ven spot could be made accurately in spite of this adverse ground effect. Flights through the transition range from hovering to normal forward flight could be performed fairly easily. The model seemed to have stability of angle of attack and angle of roll over most of the transition range. The yawing motion was divergent in the very high angle-of-attack range but could be controlled easily. At the lower angles of attack, the model seemed to become stable in yaw. In sideways flight there was an increasingly strong tendency to diverge in roll as the speed was increased and finally, at a speed of about 25 knots (full scale), the model rolled off despite efforts of the pilot to control it.

Kirby, Robert H.↗
DOE OSTI2025

A New Vehicle-to-Vehicle Communication System: Visual-Enhanced Cooperative Traffic Operations

The advent of Connected and Autonomous Vehicles (CAVs) has highlighted the necessity for robust communication systems between vehicles and their environment. This study introduces a novel vehicle-to-vehicle (V2V) communication system, termed the Visual-Enhanced Cooperative Traffic Operations (VECTOR) system. The VECTOR system addresses the need for robust communication by converting dynamic data (including velocity and yaw angle data) into binary code, which is displayed on an LED panel mounted on the top of the vehicle. Following vehicles detect this panel and decode the information using a camera, implementing a visual-based communication method. VECTOR system employs a comprehensive five-module process. Initially, polynomial fitting techniques are applied to velocity data over fixed time intervals using third-degree polynomials, with validation via R² and MSE metrics. The second module converts velocity and yaw angle data into binary form, thereby enhancing detection and processing efficiency. The third module focuses on improving detection stability across various environmental conditions to enhance traffic safety. The fourth module decodes the binary data back into trajectory information, ensuring the fidelity of velocity and yaw angles. The final module integrates eco-control through the VECTOR system, employing advanced control algorithms to minimize energy consumption in CAVs. Experimental evaluations conducted using a modified CAV test platform based on the Lincoln MKZ demonstrate the feasibility and efficiency of the VECTOR system, achieving a 75% R-squared accuracy rate in replicating original velocity data. This methodology not only highlights potential applications but also underscores significant implications for advancing CAV technology.

Ma, Ke↗
NASA NTRS1973

An analytical study of the response of a constant-attitude aircraft to atmospheric turbulence

A light airplane equipped with an automatic control system which drives large wing flaps and the stabilator so as to produce a constant pitch attitude in all flight modes was analyzed for its response to a specific gust. The aircraft was also equipped with a bank-angle steering, zero sideslip automatic control system which was studied for its effectiveness in suppressing a specific lateral gust. The gusts were assumed to be comprised of 200 lateral and 400 vertical sinusoids. Each was used to excite the controlled aircraft and the time response to the sum of all sinusoids was plotted. The assumption was that the gust may be treated as stationary in space but variable in time rather than the reverse. Results indicate that such a control system can suppress vertical gusts up to the limit of control authority. Either the lateral accelerations or the yawing velocity response to lateral gusts can be suppressed with this system but not both simultaneously.

Smetana, F. O.↗
NASA NTRS1974

Effects of several factors on theoretical predictions of airplane spin characteristics

The influence of different mathematical and aerodynamic models on computed spin motion was investigated along with the importance of some of the aerodynamic and nonaerodynamic quantities defined in these models. An analytical technique was used which included the aerodynamic forces and moments acting on a spinning aircraft due to steady rotational flow and the contribution of the rotary derivatives to the oscillatory component of the total angular rates. It was shown that (1) during experimental-analytical correlation studies, the flight-recorded control time histories must be faithfully duplicated since the spinning motion can be sensitive to a small change in the application of the spin entry controls; (2) an error in the assumed inertias, yawing moments at high angle of attack, and initial spin entry bank angle do not influence the developed spin significantly; (3) damping in pitch derivatives and the center of gravity location play a role in the spinning motion; and (4) the experimental spin investigations conducted in a constant atmospheric density environment duplicate the Froude number only at the initial full-scale spin altitude (since the full-scale airplane at high altitudes experiences large density changes during the spin.)

Bihrle, W., Jr.↗
NASA NTRS1989

Tailless aircraft performance improvements with relaxed static stability

The purpose is to determine the tailless aircraft performance improvements gained from relaxed static stability, to quantify this potential in terms of range-payload improvements, and to identify other possible operational and handling benefits or problems. Two configurations were chosen for the study: a modern high aspect ratio, short-chord wing proposed as a high-altitude long endurance (HALE) remotely piloted vehicle; a wider, lower aspect ratio, high volume wing suitable for internal stowage of all fuel and payload required for a manned long-range reconnaissance mission. Flying at best cruise altitude, both unstable configurations were found to have a 14 percent improvement in range and a 7 to 9 percent improvement in maximum endurance compared to the stable configurations. The unstable manned configuration also shows a 15 percent improvement in the 50 ft takeoff obstacle distance and an improved height response to elevator control. However, it is generally more deficient in control power due to its larger adverse aileron yaw and its higher takeoff and landing lift coefficient C(sub L), both due to the downward trimmed (vs. upward trimmed for stable configurations) trailing edge surfaces.

Ashkenas, Irving L.↗
NASA NTRS2005

Variable Structure Control of a Hand-Launched Glider

Variable structure control system design methods are applied to the problem of aircraft spin recovery. A variable structure control law typically has two phases of operation. The reaching mode phase uses a nonlinear relay control strategy to drive the system trajectory to a pre-defined switching surface within the motion state space. The sliding mode phase involves motion along the surface as the system moves toward an equilibrium or critical point. Analysis results presented in this paper reveal that the conventional method for spin recovery can be interpreted as a variable structure controller with a switching surface defined at zero yaw rate. Application of Lyapunov stability methods show that deflecting the ailerons in the direction of the spin helps to insure that this switching surface is stable. Flight test results, obtained using an instrumented hand-launched glider, are used to verify stability of the reaching mode dynamics.

Anderson, Mark R.↗
NASA NTRSDate not supplied

Reflectivity Control Device (RCD) Momentum Management for Solar Cruiser and Future Solar Sail Missions

Solar sails provide propulsion from solar photonic pressure without the need for propellant. This advantage can be reduced or eliminated if propellant is required for attitude control. The current state of the art for solar sail attitude control is that of the solar sail mission Near Earth Asteroid Scout, which employs an Adjustable Mass Translator for pitch and yaw momentum management of reaction wheels, but must use a cold gas Reaction Control System for roll axis momentum management. It is highly desirable for solar sails to use an attitude control system that does not include propellant, so here we present a novel method of managing momentum on the roll axis. For the upcoming Solar Cruiser solar sail mission, for roll axis momentum management we plan to use Reflectivity Control Devices (RCDs), thin-film Polyimide Liquid Crystal Devices that are capable of changing optical properties on command, thus affording the opportunity to provide “photonic only” control if placed appropriately on the surface of the sail. RCD design for roll momentum management is multifaceted, and must include performance (degree of change in optical properties), RCD array size, locations of clusters on the sail, orientation with respect to the sail plane, and orientation out of the sail plane. Here we provide an explanation of the basic technology, optimal orientation, sizing, and location of RCDs, results of trade studies for Solar Cruiser, lessons learned from Solar Cruiser, and scalability for future solar sail missions. RCDs will dramatically improve the performance of the Solar Cruiser Momentum Management System compared to that of NEA Scout and will continue to benefit other future solar sail missions.

Daniel Tyler↗
NASA NTRSDate not supplied

Reflectivity Control Device (RCD) Roll Momentum Management for Solar Cruiser and Future Solar Sail Missions

Solar sails provide propulsion from solar photonic pressure without the need for propellant. This advantage can be reduced or eliminated if propellant is required for attitude control. The current state of the art for solar sail attitude control is that of the solar sail mission Near Earth Asteroid Scout, which employs an Adjustable Mass Translator for pitch and yaw momentum management of reaction wheels, but must use a cold gas Reaction Control System for roll axis momentum management. It is highly desirable for solar sails to use an attitude control system that does not include propellant, so here we present a novel method of managing momentum on the roll axis. For the upcoming Solar Cruiser solar sail mission, for roll axis momentum management we plan to use Reflectivity Control Devices (RCDs), thin-film Polyimide Liquid Crystal Devices that are capable of changing optical properties on command, thus affording the opportunity to provide “photonic only” control if placed appropriately on the surface of the sail. RCD design for roll momentum management is multifaceted, and must include performance (degree of change in optical properties), RCD array size, locations of clusters on the sail, orientation with respect to the sail plane, and orientation out of the sail plane. Here we provide an explanation of the basic technology, optimal orientation, sizing, and location of RCDs, results of trade studies for Solar Cruiser, lessons learned from Solar Cruiser, and scalability for future solar sail missions. RCDs will dramatically improve the performance of the Solar Cruiser Momentum Management System compared to that of NEA Scout and will continue to benefit other future solar sail missions.

Daniel Tyler↗
DOE OSTI2021

Wake steering of multirotor wind turbines

Abstract In this paper, wake steering is applied to multirotor turbines to determine whether it has the potential to reduce wind plant wake losses. Through application of rotor yaw to multirotor turbines, a new degree of freedom is introduced to wind farm control such that wakes can be expanded, channelled or redirected to improve inflow conditions for downstream turbines. Five different yaw configurations are investigated (including a baseline case) by employing large‐eddy simulations (LES) to generate a detailed representation of the velocity field downwind of a multirotor wind turbine. Two lower‐fidelity models from single‐rotor yaw studies (curled‐wake model and analytical Gaussian wake model) are extended to the multirotor case, and their results are compared with the LES data. For each model, the wake is analysed primarily by examining wake cross‐sections at different downwind distances. Further quantitative analysis is carried out through characterisations of wake centroids and widths over a range of streamwise locations and through a brief analysis of power production. Most significantly, it is shown that rotor yaw can have a considerable impact on both the distribution and magnitude of the wake velocity deficit, leading to power gains for downstream turbines. The lower‐fidelity models show small deviation from the LES results for specific configurations; however, both are able to reasonably capture the wake trends over a large streamwise range.

17 WIND ENERGY↗
NASA NTRS2016

On Wings of the Minimum Induced Drag: Spanload Implications for Aircraft and Birds

For nearly a century Ludwig Prandtl's lifting-line theory remains a standard tool for understanding and analyzing aircraft wings. The tool, said Prandtl, initially points to the elliptical spanload as the most efficient wing choice, and it, too, has become the standard in aviation. Having no other model, avian researchers have used the elliptical spanload virtually since its introduction. Yet over the last half-century, research in bird flight has generated increasing data incongruous with the elliptical spanload. In 1933 Prandtl published a little-known paper presenting a superior spanload: any other solution produces greater drag. We argue that this second spanload is the correct model for bird flight data. Based on research we present a unifying theory for superior efficiency and coordinated control in a single solution. Specifically, Prandtl's second spanload offers the only solution to three aspects of bird flight: how birds are able to turn and maneuver without a vertical tail; why birds fly in formation with their wingtips overlapped; and why narrow wingtips do not result in wingtip stall. We performed research using two experimental aircraft designed in accordance with the fundamentals of Prandtl's second paper, but applying recent developments, to validate the various potentials of the new spanload, to wit: as an alternative for avian researchers, to demonstrate the concept of proverse yaw, and to offer a new method of aircraft control and efficiency.

aerodynamics↗
DOE OSTI2020

Field Validation of Wake Steering Control with Wind Direction Variability

Wake steering is a wind farm control strategy wherein upstream turbines are misaligned with the wind direction to redirect their wakes away from downstream turbines, increasing overall wind plant power. Wake steering is often analyzed assuming steady mean wind directions across the wind farm. However, in practice, the wind direction varies considerably over time because of large-scale weather phenomena. Wind direction variability causes the increase in power production from wake-steering to be less than predicted by steady-state models, but more robust wake-steering strategies can be designed that account for variable wind conditions. This paper compares the achieved yaw offsets and power gains from two different 2-turbine wake-steering experiments at a commercial wind farm with model predictions using the FLOw Redirection and Induction in Steady State (FLORIS) control-oriented model, assuming both fixed and variable wind directions. The impact of wind direction variability is modeled by including wind direction and yaw uncertainty in the FLORIS calculations. The field results match the trends predicted, assuming wind direction variability. Specifically, the yaw offsets achieved in the intended control regions are lower than desired, resulting in less power gain, while a slight loss in power occurs for wind directions outside of the intended control region because of unintentional yaw misalignment. The agreement between the model and field results suggests that the wind direction variability model can be used to design wake-steering controllers that are more robust to variable wind conditions present in the field.

17 WIND ENERGY↗
NASA NTRS2002

Reusable Launch Vehicle Attitude Control Using a Time-Varying Sliding Mode Control Technique

In this paper we present a time-varying sliding mode control (TVSMC) technique for reusable launch vehicle (RLV) attitude control in ascent and entry flight phases. In ascent flight the guidance commands Euler roll, pitch and yaw angles, and in entry flight it commands the aerodynamic angles of bank, attack and sideslip. The controller employs a body rate inner loop and the attitude outer loop, which are separated in time-scale by the singular perturbation principle. The novelty of the TVSMC is that both the sliding surface and the boundary layer dynamics can be varied in real time using the PD-eigenvalue assignment technique. This salient feature is used to cope with control command saturation and integrator windup in the presence of severe disturbance or control effector failure, which enhances the robustness and fault tolerance of the controller. The TV-SMC ascent and descent designs are currently being tested with high fidelity, 6-DOF dispersion simulations. The test results will be presented in the final version of this paper.

Shtessel, Yuri B.↗