Results for “vacuum processes” — Page 21

NASA NTRS2001

Application of a Fiber Optic Distributed Strain Sensor System to Woven E-Glass Composite

A distributed strain sensing system utilizing a series of identically written Bragg gratings along an optical fiber is examined for potential application to Composite Armored Vehicle health monitoring. A vacuum assisted resin transfer molding process was used to fabricate a woven fabric E-glass/composite panel with an embedded fiber optic strain sensor. Test samples machined from the panel were mechanically tested in 4-point bending. Experimental results are presented that show the mechanical strain from foil strain gages comparing well to optical strain from the embedded sensors. Also, it was found that the distributed strain along the sample length was consistent with the loading configuration.

Anastasi, Robert F.↗

NASA NTRS2002

Flaw Tolerance in Lap Shear Brazed Joints

Vacuum brazing is a viable process to achieve strong permanent and hermetic joints in space. As in any joining process, brazed Joints have various imperfections and defects. It is important to understand the impact that flaws have on the load carrying capacity and performance of the brazed joints. This study focuses on the behavior of lap shear joints due to their engineering importance in brazed aerospace structures. In Part 1 an average shear strength capabilitY and failure modes of the single lap joints are explored. Specimens comprised of 0.090 inch thick 347 stainless steel sheet brazed with pure silver are tested in accordance with the AWS C3.2 standard. Comparison of the measured loads and average shear stresses at failure with the Finite Element Analysis (FEA) of the same specimens as a function of the overlap lengths shows excellent correlation between the experimental and calculated values for the defect-free lap joints. In Part 2, various flaws will be introduced in the test specimens to simulate lack of braze coverage in the lap joints. Mechanical testing and FEA will be performed on these joints to verify if behavior of ductile ]appoints containing flaws is similar to the joints with the reduced braze area. Finally, in Part 3, the results obtained in Part 1 and 2 will be applied to the brazed assembly to evaluate a load carrying capability of the structural lap joint containing defects.

Flom, Yury↗

NASA NTRS2003

Pulsed Plasma Thruster (PPT) Technology: Earth Observing-1 PPT Operational and Advanced Components Being Developed

In 2002 the pulsed plasma thruster (PPT) mounted on the Earth Observing-1 spacecraft was operated successfully in orbit. The two-axis thruster system is fully incorporated in the attitude determination and control system and is being used to automatically counteract disturbances in the pitch axis of the spacecraft. The first tests conducted in space demonstrated the full range of PPT operation, followed by calibration of control torques from the PPT in the attitude control system. Then the spacecraft was placed in PPT control mode. To date, it has operated for about 30 hr. The PPT successfully controlled pitch momentum during wheel de-spin, solar array acceleration and deceleration during array rewind, and environmental torques in nominal operating conditions. Images collected with the Advanced Landsat Imager during PPT operation have demonstrated that there was no degradation in comparison to full momentum wheel control. In addition, other experiments have been performed to interrogate the effects of PPT operation on communication packages and light reflection from spacecraft surfaces. Future experiments will investigate the possibility of orbit-raising maneuvers, spacecraft roll, and concurrent operation with the Hyperion imager. Future applications envisioned for pulsed plasma thrusters include longer life, higher precision, multiaxis thruster configurations for three-axis attitude control systems or high-precision, formationflying systems. Advanced components, such as a "dry" mica-foil capacitor, a wear-resistant spark plug, and a multichannel power processing unit have been developed under contract with Unison Industries, General Dynamics, and C.U. Aerospace. Over the last year, evaluation tests have been conducted to determine power processing unit efficiency, atmospheric functionality, vacuum functionality, thruster performance evaluation, thermal performance, and component life.

Pencil, Eric J.↗

NASA NTRS2009

Young's Moduli of Cold and Vacuum Plasma Sprayed Metallic Coatings

Monolithic metallic copper alloy and NiCrAlY coatings were fabricated by either the cold spray (CS) or the vacuum plasma spray (VPS) deposition processes. Dynamic elastic modulus property measurements were conducted on these monolithic coating specimens between 300 K and 1273 K using the impulse excitation technique. The Young's moduli decreased almost linearly with increasing temperature at all temperatures except in the case of the CS Cu-23%Cr-5%Al and VPS NiCrAlY, where deviations from linearity were observed above a critical temperature. It was observed that the Young's moduli for VPS Cu-8%Cr were larger than literature data compiled for Cu. The addition of 1%Al to Cu- 8%Cr significantly increased its Young's modulus by 12 to 17% presumably due to a solid solution effect. Comparisons of the Young s moduli data between two different measurements on the same CS Cu- 23%Cr-5%Al specimen revealed that the values measured in the first run were about 10% higher than those in the second run. It is suggested that this observation is due to annealing of the initial cold work microstructure resulting form the cold spray deposition process.

Raj, S. V.↗

NASA NTRS2008

Thermal Vacuum Control Systems Options for Test Facilities

This presentation suggests several Thermal Vacuum System (TVAC) control design approach methods for TVAC facilities. Over the past several years many aerospace companies have or are currently upgrading their TVAC testing facilities whether it be by upgrading old equipment or purchasing new. In doing so they are updating vacuum pumping and thermal capabilities of their chambers as well as their control systems. Although control systems are sometimes are considered second to the vacuum or thermal system upgrade process, they should not be taken lightly and must be planned and implemented with the equipment it is to control. Also, emphasis should be placed on how the operators will use the system as well as the requirements of "their" customers. Presented will be various successful methods of TVAC control systems from Programmable Logic Controller (PLC) based to personal computer (PC) based control.

Marchetti, John↗

NASA NTRS2010

Phenylethynyl Terminated Imide (PETI) Composites Made by High Temperature Vartm

The use of composites as primary structures on aerospace vehicles has increased dramatically over the past decade. As these advanced structures increase in size and complexity, their production costs have grown significantly. A major contributor to these manufacturing costs is the requirement of elevated pressures, during high temperature processing, to create fully consolidated composite parts. Recently, NASA Langley has licensed a series of low viscosity Phenyl Ethynyl Terminated Imide, PETI, oligomers that possess a wide processing window to allow for Resin Transfer Molding, RTM, processing. These resins, PETI-8 and PETI-330, demonstrate void fractions of approx.1% under elevated pressure consolidation. However, when used with a standardized thermal curing cycle in a High Temperature Vacuum Assisted RTM (HT-VARTM) process, they display undesirable void contents in excess of 7%. It was determined previously that under the thermal cycles used for laminate fabrication, the phenylethynyl endcap underwent degradation leading to volatile evolution. Modifications to the processing cycle used in the laminate fabrication have reduced the void content significantly (typically less than 3%) for carbon fiber biaxially woven fabric. For carbon fiber uniaxial fabric, void contents of less than 2% have been obtained using both PETI-8 and PETI-330. The resins were infused into carbon fiber preforms at 260 C and cured between 316 C and 371 C. Photomicrographs of the panels were taken and void contents were determined by acid digestion. Mechanical properties of the panels were determined at both room and elevated temperatures. These include short beam shear and flexure tests. The results of this work are presented herein.

Ghose, Sayata↗

NASA NTRS2005

Texturing Blood-Glucose-Monitoring Optics Using Oxygen Beams

A method has been invented for utilizing directed, hyperthermal oxygen atoms and ions for texturing tips of polymeric optical fibers or other polymeric optical components for use in optical measurement of concentration of glucose in blood. The required texture of the sensory surface of such a component amounts to a landscape of microscopic hills having high aspect ratios (hills taller than they are wide), with an average distance between hills of no more than about 5 m. This limit on the average distance between hills is chosen so that blood cells (which are wider) cannot enter the valleys between the hills, where they could obstruct optical sensing of glucose in the blood plasma. On the other hand, the plasma is required to enter the valleys, and a high aspect ratio is intended to maximize the hillside and valley surface area in contact with the plasma, thereby making it possible to obtain a given level of optical glucose- measurement sensitivity with a relatively small volume of blood. The present method of texturing by use of directed, hyperthermal (particle energy >1 eV) oxygen atoms and ions stands in contrast to a prior method of texturing by use of thermal monatomic oxygen characterized by a temperature of the order of 0.5 eV. The prior method yields low-aspect- ratio (approximately hemispherical) craters that are tens of microns wide . too wide to exclude blood cells. The figure schematically depicts parts of a typical apparatus for texturing according to the present method. One or more polymeric optical components to be textured (e.g., multiple optical fibers bundled together for simultaneous processing) are mounted in a vacuum chamber facing a suitable ion- or atom-accelerating device capable of generating a beam of oxygen atoms and/or ions having kinetic energies >1 eV. Typically, such a device includes a heated cathode, in which case it is desirable to interpose a water-cooled thermal-radiation shield to prevent melting of the polymeric component(s) to be textured. In operation, the chamber is evacuated to a pressure .10.5 torr (less than or equal to approximately 1.3 mPa), then the beam is turned on. The resulting texture is characterized by approximately conical hills having aspect ratios greater than 1. In experiments, it was demonstrated that separations between adjacent hills can be made .1 m and that the separations and heights of the hills can be varied by varying the fluence of monatomic oxygen and/or oxygen ions.

Banks, Bruce↗

NASA NTRSDate not supplied

Metallic Powder Core Tubular Wire Development for Additive Manufacturing

NASA Langley Research Center (LaRC) in Hampton, VA, and the Center for Welding, Joining, and Coating Research (CWJCR) in the Department of Metallurgical and Materials Engineering at the Colorado School of Mines (CSM) in Golden, CO, have collaborated for nearly fifteen years to develop metallic powder core tubular wire (PCTW) feedstock for additive manufacturing (AM) using electron beam deposition. The motivation for this development was to offset dealloying observed during deposition of titanium and aluminum alloy solid wire feedstock in the LaRC electron beam freeform fabrication (EBF3) system and to explore novel alloy compositions by tailoring the powder fill. EBF3 is a fusion-based AM process that is performed under vacuum and is consequently prone to vaporization loss of low vapor pressure alloying elements. Research spanning four graduate student research projects succeeded in developing the basic methodology to fabricate PCTW, the mass balance equations used to define the powder fill, microstructure control through particulate inoculation, and the feasibility of producing metal matrix composite materials.

powder core tubular wire (PCTW)↗

NASA NTRSDate not supplied

Optimization of the 4-Bed CO2 Scrubber Performance Based on Ground Tests

Testing of ground hardware closely matching the flight design for the 4-Bed CO2Scrubber (4BCO2) has provided a wealth of information about the complex and highly coupled batch process. The 4BCO2 process is a Thermal and Vacuum Swing Adsorption (TVSA) cycle with recirculating flows. The ability to measure CO2concentration at intermediate points in this architecture is new to this ground test system and has revealed a better understanding of system performance and its dependence on system design, operational parameters, and boundary conditions. This paper will discuss a statistical analysis performed to identify significant correlations between performance factors and operational parameters. Using these new insights on the highly coupled system physics, means for improvements to system performance are proposed.

CO2 Removal↗

NASA NTRSDate not supplied

Thermal Protection System P50 Cork Char Response Characterization to Ascent Flight Shear and Heating Environments

NASA’s Space Launch System (SLS) experienced deflagration of the acreage of the Core Stage base heat shield during the Green Run hot-fire test campaigns and Artemis I flight. The burning products from the base heat shield during Green Run hot-fire test operation led to concerns in aerothermal environments and thermal protection system (TPS) performance prior to Artemis I flight. Updated design thermal environments accounting for cork combustion were developed using Green Run measurements and assessed prior to Artemis I, resulting in increased TPS thickness for the base heat shield. This work documents a highly controlled ground test within the NASA Marshall Space Flight Center’s Propulsion Test Branch Hot Gas Facility (HGF) and investigates the P50 cork TPS response due to sensitivity changes in radiative heat rates and surface shear stress. Prior to testing at the HGF, most of the P50 cork panels had a thick layer of char due to the cork combustion process replicated in a thermal vacuum chamber. SLS ascent shear stress and heating rate profile were simulated within the HGF by running the combustion-driven wind tunnel at off-nominal conditions and Mach numbers below 1. This test data provided insight into aerothermal measurements from Artemis I flight as well as informing updated base heating design environments for Artemis II. An in-depth understanding of the TPS P50 cork char response and observations is presented for launch vehicle flight ascent environments.

aerothermodynamics↗

DOE OSTI2021

BETO 2021 Peer Review - Process Monitoring and Predictions of Biorefinery Performance

Online process monitoring coupled with rapid predictive tools will be essential to refineries of the future to provide real-time feedback and process control on new, renewable feeds and their accompanying processes and products. This project will provide refinery operators with tools to predict product component concentrations in minutes from online, slip stream mass spectra, allowing for rapid detection of off-specification product. We will arrive at a template for predictive tool generation through the development of a specific tool as a starting point -- co-processing of pyrolysis oils and vacuum gas oil over fluid catalytic cracking (FCC) catalysts.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗

NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗

NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗

DOE OSTI2022

Thermal Instability in the Manufacturing of Wind Turbine Blade Spar Caps – Phase 2

As the wind turbine industry continues to develop, the technology surrounding the design, development, and manufacturing of blades requires advancement as well. Wind turbine blades continue to increase in size, increasing the cost and time associated with manufacturing. Simulation driven manufacturing cycle design is required for the industry to maintain manufacturing schedules and optimize the manufacturing process. A recent effort to reduce the cycle time of wind blade spar caps encountered a recurring manufacturing defect during the exotherm and curing of the resin system after filling in the vacuum-assisted resin transfer molding (VARTM) process. Thermal waves developed in sections of the spar cap resulting in unacceptable part tolerances, requiring the parts to be thrown out. The first phase of this IACMI project focused on characterizing the fabric and epoxy system used in manufacturing and simulating the manufacturing process to determine the root cause of the thermal waves. The second phase of this project refined and validated the manufacturing simulations. The simulation workflow was then used to analyze multiple cure cycle options to determine if the thermal waves would appear. The estimated filling time from the filling simulation was shown to match well to experiment, and the temperature history from the curing simulation lined up well with experiment. This indicates that these simulations could be used to evaluate future curing cycles to be used with manufacturing. It is recommended that the distortion simulation work be completed for this project, as it would allow for further manufacturing cycle evaluation through the prediction of stresses and strains in the part. This could provide indicators of defects like the thermal waves seen in manufacturing earlier.

17 WIND ENERGY↗

NASA NTRS1975

Space processing of composite materials

Materials and processes for the testing of aluminum-base fiber and particle composites, and of metal foams under extended-time low-g conditions were investigated. A wetting and dispersion technique was developed, based on the theory that under the absence of a gas phase all solids are wetted by liquids. The process is characterized by a high vacuum environment and a high temperature cycle. Successful wetting and dispersion experiments were carried out with sapphire fibers, whiskers and particles, and with fibers of silicon carbide, pyrolytic graphite and tungsten. The developed process and facilities permit the preparation of a precomposite which serves as sample material for flight experiments. Low-g processing consists then merely in the uniform redistribution of the reinforcements during a melting cycle. For the preparation of metal foams, gas generation by means of a thermally decomposing compound was found most adaptable to flight experiments. For flight experiments, the use of compacted mixture of the component materials limits low-g processing to a simple melt cycle.

Steurer, W. H.↗

NASA NTRS1998

Development of Textile Reinforced Composites for Aircraft Structures

NASA has been a leader in development of composite materials for aircraft applications during the past 25 years. In the early 1980's NASA and others conducted research to improve damage tolerance of composite structures through the use of toughened resins but these resins were not cost-effective. The aircraft industry wanted affordable, robust structures that could withstand the rigors of flight service with minimal damage. The cost and damage tolerance barriers of conventional laminated composites led NASA to focus on new concepts in composites which would incorporate the automated manufacturing methods of the textiles industry and which would incorporate through-the-thickness reinforcements. The NASA Advanced Composites Technology (ACT) Program provided the resources to extensively investigate the application of textile processes to next generation aircraft wing and fuselage structures. This paper discusses advanced textile material forms that have been developed, innovative machine concepts and key technology advancements required for future application of textile reinforced composites in commercial transport aircraft. Multiaxial warp knitting, triaxial braiding and through-the-thickness stitching are the three textile processes that have surfaced as the most promising for further development. Textile reinforced composite structural elements that have been developed in the NASA ACT Program are discussed. Included are braided fuselage frames and window-belt reinforcements, woven/stitched lower fuselage side panels, stitched multiaxial warp knit wing skins, and braided wing stiffeners. In addition, low-cost processing concepts such as resin transfer molding (RTM), resin film infusion (RFI), and vacuum-assisted resin transfer molding (VARTM) are discussed. Process modeling concepts to predict resin flow and cure in textile preforms are also discussed.

Dexter, H. Benson↗

DOE OSTI2026

Control of Nonlinear Compton Scattering in a Squeezed Vacuum

Electromagnetic radiation by accelerated charges is a fundamental process in physics. Here, we introduce a quantum-optical framework for controlling the emission of radiation of an electron in an intense laser field via squeezed vacuum states. By engineering the quantum fluctuations of the emission modes, we demonstrate that the probability of nonlinear Compton scattering can be significantly enhanced or suppressed through tunable squeezing amplitude and angle. We show numerically that our predictions are experimentally accessible with current squeezing technologies, establishing a new paradigm for quantum control in high-intensity light-matter interactions.

Light-matter interaction↗