Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tool influence function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

373 records · Page 21

Development of an Inertial Sensor-based Methodology for Spacesuited Geology Task Assessments during Simulated Lunar Extravehicular Activities

Lunar surface exploration during Artemis missions will require the specific skill set of geology sampling. Apollo astronauts had extensive training and used specialized tools to collect lunar rocks, core samples, pebbles, sand, and dust. The inflexibility of the pressurized Apollo spacesuits forced sampling to be taken at a standstill posture. However, new exploration spacesuits are expected to incorporate advanced materials and joint bearings, allowing for greater mobility and a wider range of functional postures. Thus, science and exploration during Artemis missions will likely involve a variety of standing, squatting, and kneeling postures. In preparation for future lunar exploration missions, NASA provides geologic training to astronauts and other mission personnel. This professional training with a spacesuit in simulated lunar environments will enhance performance and reduce risk of injury to astronauts on the lunar surface. However, anecdotally, untrained or newly trained people wearing prototype planetary spacesuits have been observed to performing motions differently than a trained geologist would when conducting the same geology sampling tasks. Therefore, a tool for evaluating geology postures at extravehicular activity (EVA) training facilities becomes required. In this paper, we introduce a novel inertial measurement unit (IMU)-based method of geology task assessments in spacesuited conditions during simulated lunar EVAs. As a case study, two subjects (one geologist and one non-geologist) participated and donned the Mark III prototype planetary spacesuit during offloading with the spreader bar gimbal in NASA’s Active Response Gravity Offload System (ARGOS). For automated geology task assessments, the spacesuit was instrumented with three wireless IMUs (APDM Opal, OR, USA): one on the chest and one each on the left and right ankle bearings. Then subjects performed geology tasks using various tools (rake, trench, hammer chisel, scoop, and drive tube) for 45 minutes each. The chest IMU measured the torso tilt angle in the sagittal plane. We used an ensemble learning method with the ankle IMUs to discriminate between standing and kneeling activities. IMU data were processed using custom MATLAB (Mathworks, MA, USA) software. In our case study, the developed method was able to discriminate differences in standing and kneeling activity levels between subjects who were all highly experienced with spacesuited testing. Our preliminary data showed one subject maintained the constant and lower range of the upper body tilt angle while both standing and kneeling, while the other subject showed more variation of the upper body tilt angle and preferred bending the upper body rather than changing from standing to kneeling posture and vice versa. While geology experience may be a factor, these results need further investigation as suit sizing and ARGOS offloading configurations have been proven to have a significant influence on suited ARGOS tasks. Also, more subjects will be needed to complete these tasks for validation. IMU-based geology task assessments can provide useful information for geology training programs. Additionally, our IMU-based posture analysis can provide new insights into how to evaluate spacesuited geology task characteristics of astronauts during simulated lunar EVAs.

Kyoung Jae Kim↗

Asymmetries in cloud microphysical properties ascribed to sea ice leads via water vapour transport in the central Arctic

To investigate the influence of sea ice openings like leads on wintertime Arctic clouds, the air mass transport is exploited as a heat and humidity feeding mechanism which can modify Arctic cloud properties. Cloud microphysical properties in the central Arctic are analysed as a function of sea ice conditions during the Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expedition in 2019–2020. The Cloudnet classification algorithm is used to characterize the clouds based on remote sensing observations and the atmospheric thermodynamic state from the observatory on board the research vessel (RV) Polarstern. To link the sea ice conditions around the observational site with the cloud observations, the water vapour transport (WVT) being conveyed towards RV Polarstern has been utilized as a mechanism to associate upwind sea ice conditions with the measured cloud properties. This novel methodology is used to classify the observed clouds as coupled or decoupled to the WVT based on the location of the maximum vertical gradient of WVT height relative to the cloud-driven mixing layer. Only a conical sub-sector of sea ice concentration (SIC) and the lead fraction (LF) centred on the RV Polarstern location and extending up to 50 km in radius and with an azimuth angle governed by the time-dependent wind direction measured at the maximum WVT is related to the observed clouds. We found significant asymmetries for cases when the clouds are coupled or decoupled to the WVT and selected by LF regimes. Liquid water path of low-level clouds is found to increase as a function of LF, while the ice water path does so only for deep precipitating systems. Clouds coupled to WVT are found to generally have a lower cloud base and larger thickness than decoupled clouds. Thermodynamically, for coupled cases the cloud-top temperature is warmer and accompanied by a temperature inversion at the cloud top, whereas the decoupled cases are found to be closely compliant with the moist adiabatic temperature lapse rate. The ice water fraction within the cloud layer has been found to present a noticeable asymmetry when comparing coupled versus decoupled cases. This novel approach of coupling sea ice to cloud properties via the WVT mechanism unfolds a new tool to study Arctic surface–atmosphere processes. With this formulation, long-term observations can be analysed to enforce the statistical significance of the asymmetries. Furthermore, our results serve as an opportunity to better understand the dynamic linkage between clouds and sea ice and to evaluate its representation in numerical climate models for the Arctic system.

54 ENVIRONMENTAL SCIENCES↗

ROCK DEFORMATION 2010 GORDON RESEARCH CONFERENCE, AUGUST 8-13, 2010

Creep in the crust and mantle is commonly considered a steady-state process. This view prevails despite the fact that earthquakes do not represent steady-state and at the base of the seismogenic zone, for example, the stresses that drive creep must vary with the earthquake cycle. The contribution of transient versus steady-state behavior is not easy to determine from naturally-deformed brittle or plastic rocks and our view of steady-state depends on whether we consider geological or shorter time-scales. Perhaps we avoid a non steady-state picture because we lack appropriate descriptive or quantitative tools. The aim of the 2010 Gordon Research Conference (GRC) in rock deformation is to explore what we know about non steady-state deformation and how we might advance our understanding through geological and geophysical field investigations, laboratory experiments and modeling. This will require an appraisal of the applicability of steady-state concepts as well as an exploration of transient behavior, in which processes and physical properties cycle between different states as might be the case during earthquake cycles, and transitions in behavior, where finite strain or changing environmental conditions lead to changes in processes and properties. Conference sessions will cover seven broad and interlinked topics. (1) What is steady state?; an appraisal of applicability of the steady-state concept in rock deformation. (2) Seismogenic Faulting and Brittle Fault Rocks; where transience in rates and conditions are accepted but not fully understood. (3) Episodic Creep During the Seismic Cycle; with a focus on processes in areas adjacent to the base of the seismogenic zone. (4) Creep in Zones of Stress and Temperature Cycling; considering deformation in real-world complex systems (5) Deformation, Metamorphism, and Fluids; exploring the interaction of diagenesis/metamorphism and thermal instabilities with deformation. (6) Mechanism and Microstructure Transitions During Deformation; quantifying evolution as a function of strain and associated with changes in deformation kinematics or conditions. (7) Mechanism and Microstructure Transitions Related to Mantle Geophysics; with a focus on the link between mechanisms affecting processes on geological time-scales on the time-scales associated with seismic wave propagation. The GRC on Rock Deformation aims to bring together researchers with diverse expertise, and to shape the scientific debate and provide inspiration for young researchers to fill the still extensive gaps in our knowledge of how the Earth deforms. The processes that will be discussed have wide applications in both basic and applied research. A key issue, of fundamental importance to our understanding of the Earth, for discussion at this meeting will be the transition from time-dependent (and distributed) rock deformation, including both high temperature creep and brittle creep, to episodic (and more localized) events. Such transitions have both a scientific and a socio-economic impact since they control the precursory phases of important geohazards such as earthquake rupture and volcanic eruptions, and also influence effective recovery of hydrocarbon and geothermal energy resources, and the integrity of long-term storage facilities for hazardous waste.

15 GEOTHERMAL ENERGY↗

f-Orbital Mixing in the Octahedral f 2 Compounds UX 6 2– [X = F, Br, Cl, I] and PrCl 6 3–

Understanding how interactions between the f orbitals and ligand orbitals in lanthanide and actinide systems affect their physical properties is the central issue in f-element chemistry. A wide variety of approaches including both theoretical and experimental tools have been used to study these relationships. Among the most widely used tools has been crystal field theory (CFT), which bridges theory and experiment in that it is a model based largely on atomic theory that is parametrized using experimental data. Crystal field theory is quite accurate for the lanthanides, due in part to the highly contracted nature of the 4f orbitals. For actinides, crystal field theory is less accurate, potentially due to the treatment of orbital mixing. In CFT, orbital mixing is handled implicitly by allowing the electron repulsion parameters (Slater F k parameters) and the spin–orbit coupling constant to vary. As a result, orbital mixing in CFT is isotropic in that the F k parameters and the spin–orbit coupling constant affect all f orbitals equally. This approximation works well for the lanthanides due to the limited degree of orbital mixing in these complexes. In actinide complexes, the 5f orbitals have greater overlap with the ligand orbitals, and this approximation is less accurate than in the lanthanides. In this work, we report a modification of CFT that includes the effect of orbital mixing on electron repulsion and spin–orbit coupling for each f orbital. The model is applied to the tetravalent uranium hexahalide dianions and PrCl 6 3– for which the energies of many low-lying excited states are known. The new model generally fits the data as well the traditional CFT although with fewer parameters. However, the new model does not fit the data better than the more complex CFT models of Faucher and co-workers. The results of the model show in detail how changes in overlap and orbital energies influence the energies of the bonding and antibonding orbitals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Capturing Surface Coverage Effects in Heterogeneous Catalysis

Adsorbate–adsorbate lateral interactions at relevant surface coverages have a significant effect on chemical kinetics, thereby influencing the activity of a heterogeneous catalyst. Coverage-dependent kinetic and thermodynamic parameters therefore must be included in studies of such complex systems to properly predict the turnover frequencies and kinetic trends. Thus, it becomes extremely important to accurately capture the strength of lateral interactions between neighboring species under realistic reaction conditions. In this Perspective, we discuss the various existing computational and experimental methods for determining adspecies coverage and configurational effects. The choice of the tools and methods employed in such studies depends on factors such as time, length scales, computational cost, the presence of solvents, and reaction conditions. The applications of each method and the respective challenges are also discussed here. As a result, we discuss the recent developments and future of the state-of-the-art for inclusion of surface coverage and configuration into a holistic picture for accurate predictions of catalytic behavior.

09 BIOMASS FUELS↗

Assessment of Tools and Data for System-Level Dynamic Analyses

The only fuel cycle for which dynamic analyses and assessments are not needed is the null fuel cycle - no nuclear power. For every other concept, dynamic analyses are needed and can influence relative desirability of options. Dynamic analyses show how a fuel cycle might work during transitions from today's partial fuel cycle to something more complete, impact of technology deployments, location of choke points, the key time lags, when benefits can manifest, and how well parts of fuel cycles work together. This report summarizes the readiness of existing Fuel Cycle Technology (FCT) tools and data for conducting dynamic analyses on the range of options. VISION is the primary dynamic analysis tool. Not only does it model mass flows, as do other dynamic system analysis models, but it allows users to explore various potential constraints. The only fuel cycle for which constraints are not important are those in concept advocates PowerPoint presentations; in contrast, comparative analyses of fuel cycles must address what constraints exist and how they could impact performance. The most immediate tool need is extending VISION to the thorium/U233 fuel cycle. Depending on further clarification of waste management strategies in general and for specific fuel cycle candidates, waste management sub-models in VISION may need enhancement, e.g., more on 'co-flows' of non-fuel materials, constraints in waste streams, or automatic classification of waste streams on the basis of user-specified rules. VISION originally had an economic sub-model. The economic calculations were deemed unnecessary in later versions so it was retired. Eventually, the program will need to restore and improve the economics sub-model of VISION to at least the cash flow stage and possibly to incorporating cost constraints and feedbacks. There are multiple sources of data that dynamic analyses can draw on. In this report, 'data' means experimental data, data from more detailed theoretical or empirical calculations on technology performance, and assumptions such as the earliest date a technology can be deployed. The only fuel cycles for which we currently have adequate data are those we are sure we will never build, e.g., a PUREX plant in the U.S. For actual candidates, even for once through LWRs, there remain missing data such as how the fuel cycle would be completed with a geologic repository. The most immediate data needs are probably basic reactor physics data for new concepts and data associated with waste management for anything other than current technology. The readiness of tools and data is fluid and depends on what purposes are envisioned to drive upcoming analyses and further definition of the waste-related characteristics of fuel cycle candidates. Tools and data sets evolve as needs evolve. Thus, much of the document explains that if the FCT program wants a certain type of analysis, then the tools and data needs are as indicated. For example, functions can be treated as either commodities or facilities. Reactors, separation, fuel fabrication, repository are treated as facility types. Other functions such as uranium mining, conversion, enrichment, and waste packaging and non-repository disposal are treated as commodities and therefore not modeled as extensively. In summary, the tools are functional and can answer many fuel cycle questions but some analyses will require that the tools be modified to support those analyses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fundamental Studies of Metal Centered Transformations Relevant to Catalysis

The overall objectives the research performed have been to advance the mission of the U. S. Department of Energy, with specific emphasis concerned with the conversion and use of fossil and renewable energy resources, and the synthesis of advanced chemicals. Achieving this objective requires improvements in rational catalyst design by establishing details of reaction mechanisms and their kinetics. Therefore, over the course of this award, emphasis has been directed towards obtaining detailed information concerned with fundamental transformations that occur at metal centers, with particular attention given towards reactions such as (i) hydrodesulfurization (HDS) and hydrodenitrogenation (HDN), (ii) the use of carbon dioxide as a renewable C1 feedstock, (iii) the generation of hydrogen on demand, and (iv) transformations that involve the cleavage of H–H, C–H and C–C bonds. HDS and HDN are the essential processes for removing sulfur- and nitrogen-containing impurities from crude oil in order to obtain (i) cleaner fuels that minimize environmental pollution and (ii) cleaner chemical feedstocks that are less likely to poison the catalysts that are used for subsequent transformations. The catalysts employed for HDS and HDN are typically molybdenum and tungsten sulfides and, to gain insight into these transformations at the molecular level, we have focused on developing the coordination chemistry of heterocyclic sulfur and nitrogen compounds with molybdenum and tungsten. For example, we obtained the first examples of the cleavage of thiophene C–S bonds by employing molecular molybdenum compounds. The efficient utilization of carbon dioxide as a renewable C 1 source for the synthesis of value added organic chemicals and fuels has prompted much effort towards developing catalytic reactions to functionalize CO 2 . One such approach is hydrosilylation, which can proceed in a stepwise manner to afford a series of products with different levels of reduction, namely silyl formates, silyl acetals, methoxy silanes and methane. Despite the utility of these transformations, however, most catalysts employ precious metals, which operate at elevated temperatures, and control of the level of reduction is challenging. Therefore, it is significant that we have developed zinc and magnesium systems that can achieve hydrosilylation of CO 2 and which may be modified to control the level of reduction. The growing demand for energy requires the development of alternative energy sources that are more sustainable than fossil fuels and have a reduced impact on the environment. In this regard, an attractive energy storage medium is provided by hydrogen, which can, for example, be consumed in a fuel cell with only water as a byproduct. Unfortunately, a problem with using hydrogen in this manner is that present storage and transportation techniques are inadequate. For example, not only does storing liquid hydrogen present a safety risk, considerable energy is also required to liquefy the hydrogen and maintain it in this form. Therefore, we have focused on the application of chemical methods to provide hydrogen on demand. One such method utilizes formic acid as a storage medium and we reported the first examples of molybdenum compounds that serve as catalysts for releasing H 2 from formic acid. The nature of the interaction of a C–H bond with a metal center is of pivotal importance in many transformations of organic molecules, and we have examined several systems to probe how the interaction varies according to whether the metal is molybdenum or tungsten. These studies demonstrate that tungsten exhibits a greater propensity to cleave a C–H bond. While the oxidative addition of C–H bonds to a metal center is well precedented, transformations that feature oxidative addition of C–C bonds are uncommon and so it is noteworthy that we have observed the cleavage of a strong C–C bond that is a component of an unstrained 6-membered aromatic ring. The oxidative addition of dihydrogen to a metal center, and its microscopic reverse, reductive elimination, are two of the simplest yet most important transformations in organometallic chemistry. For example, oxidative addition of dihydrogen is a key step in many transition metal-catalyzed reactions involving H 2 . However, relatively few studies have established in detail the factors that influence the thermodynamics of this transformation. Therefore, it is significant that we demonstrated experimentally that that the energetics of the oxidative addition of H 2 to the six coordinate molybdenum and tungsten halide complexes depends very strongly on the nature of both the metal and the halogen. Deuterium kinetic isotope effects (KIEs) and equilibrium isotope effects (EIEs) serve as versatile tools to infer details about reaction mechanisms. In this regard, primary deuterium isotope effects are often interpreted by using two simple guidelines: (i) the KIE for an elementary reaction is normal (k H /k D > 1) and (ii) the EIE is dictated by deuterium preferring to be located in the site corresponding to the highest frequency oscillator. We have evaluated the applicability of these rules to the interactions of H–H and C–H bonds with a transition metal center and our results question the ability to predict primary EIEs in these systems based on the simple notion that deuterium prefers to occupy the highest frequency oscillator. The key findings are that the EIEs for (i) formation of σ–complexes by coordination of H–H and C–H bonds and (ii) oxidative addition of dihydrogen exhibit unusual temperature dependencies, such that the same system may exhibit both normal (i.e. K H /K D > 1) and inverse (i.e. K H /K D < 1) values.

02 PETROLEUM↗

Investigation of Best-Practices and Computationally Inexpensive Radiative Exchange Models for Discrete Element Method Modeling of Aluminosilicate Particles in Concentrating Solar Power Environments

Chemically inert, aluminosilicate based particles have been investigated as both a thermal transport and sensible energy storage medium for concentrating solar power facilities. These particles will experience a wide range of operating temperatures (300-1000 K) and handling conditions (dense to dilute falling particle curtains, dense granular flows, or dense structures), requiring specially-designed and optimized infrastructures. The relative influence of collisional and frictional interactions between particles varies based on temperature-dependent particulate properties and greatly impacts the bulk, granular flow behavior. These underlying physics are captured using discrete element method modeling tools. However, this modeling method is computationally expensive as each particle position and interaction is tracked during the simulation. These modeling methods are further complicated by introducing temperature-dependent particle properties, high-temperature radiative exchange, and directional irradiation sources experienced by granular flows in concentrating solar power environments. In this study, coupled experimental and numerical slump testing of aluminosilicate particles was performed and computationally efficient radiative exchange models were evaluated to establish best-practices for discrete element method models for concentrating solar power environments. The three particle types investigated included Carbobead HSP 30 /60, Carbobead CP 30/60, and Granusil 4030. Existing modeling limitations and computationally-efficient multi-modal heat transfer models were evaluated using Aspherix®, a commercial discrete element method software. High-temperature (< 1073 K) slump testing of aluminosilicate particles was performed to investigate the deviation between experimentally-observed and numerically-predicted angles of repose introduced by computation-time reduction practices including the relaxation of the particle elastic modulus and coarse-graining. Coarse-graining is used to use a single modeled particle that is representative of a collection of smaller particles, decreasing the computational cost at the expense of geometric accuracy. Additionally, relaxation of the elastic modulus is used to reduce computational time at the expense of an increased, modeled particle overlap. Prior studies have determined that aluminosilicate particles retain a high elastic modulus at high temperatures (< 1073 K), requiring small simulation timesteps to ensure resolved contact forces resemble appropriate solid mechanics. A parametric study was performed to evaluate the influence of computation time improvements on the deviation between experimental and modeled angle of repose across high temperatures < 1073 K. Additionally, numerical case studies were performed on candidate particle systems at varying porosities and temperatures. These studies were performed to investigate the influence of computationally-efficient radiative-exchange modeling methods coupled to Aspherix® on modeled accuracy and computation time. The recently-developed distance-based approximation was evaluated in estimating radiative exchange between particles and participating surfaces located in close proximity. The distance based approximation was developed to use tabulated estimates of the radiative distribution factor between individual particles and surfaces in close proximity (< 40 particle radii). These methods were expanded to the aluminosilicate particles of interest, including the influence of particle size distributions. To capture radiative exchange between particles and surfaces not in close proximity (> 40 particle radii) and to capture the absorption of directional irradiation from concentrating solar resources, a volumetrically-averaged radiative distribution factor was calculated between the modeled granular flow and surfaces using Monte Carlo ray-tracing for participating media. Volume-averaged absorption and scattering coefficients were predicted using a volumetric discretization of the modeled domain with monodisperse approximations based on geometric optics and experimentally-determined scattering phase functions for aluminosilicate particles.

14 SOLAR ENERGY↗

Final Report: In-Situ TEM Observations of Degradation Mechanisms in Next-Generation High-Energy Density Lithium-Ion Battery Systems

This project originally sought to characterize nanoscale processes associated with the degradation of next-generation high energy density lithium-ion battery electrodes via in-situ transmission electron microscopy (TEM). The research also focused on developing the experimental techniques necessary for investigating electrochemical systems by in-situ transmission electron microscopy and providing a framework for understanding and quantifying electron beam effects that influence experimental results. In line with these goals, this project demonstrated and published the first in-situ TEM cycling of a Li-ion battery electrode in commercially relevant non-aqueous electrolyte: a technique subsequently adopted by a number of researchers in the field. Experiments performed on Sn anodes, demonstrated porosity evolution during Li dealloying as a mechanism for strain accommodation during the first cycle, and observed partially reversible crystalline to amorphous phase transitions associated with Li insertion and extraction in subsequent cycles. Complementary study of in-situ dealloying in a simple model, Au-Cu, was also performed. We also published the earliest quantitative measurements of electron beam effects in aqueous and non-aqueous liquids. Specifically, we utilized a model system to quantify the fraction of incident electron beam that contributed to charge transfer mediated reactions in non-aqueous liquid, since such liquids are primarily dose sensitive. We also quantified the evolution of model aqueous chemistries as a function of dose rate and chemical potential to better understand the reaction mechanisms active in liquids exposed to electron beams. The original project goals included the use of controlled environments to simulate different battery operational conditions. To aid such experiments, we developed new experimental apparatuses and techniques to perform in-situ liquid cell TEM under controlled temperature, including heating and cooling. We demonstrated this capability in aqueous systems; specifically understanding phase selection and solid-liquid interface interactions with particles during water crystallization and hydrothermal precipitation kinetics of ZnO. We also published the first demonstration of in-situ TEM based high-field (plasma) experiments and in-situ TEM of aqueous photochemistry, which demonstrated an previously unrecognized early growth mode transition during Au sputtering and delocalization of gas bubble nucleation during water splitting, respectively. In addition to the scientific results, this portion of the project greatly expanded the range of systems that can be characterized in realistic environments at the nanoscale via in-situ TEM. Unfortunately, commercial battery electrolytes are quite sensitive to electron dose. This limits the time of acquisition and/or the spatial resolution of the experiments. The same problem has been encountered in all subsequent publications in the field. The major problem, relative to the project original goals, is that long term cycling is challenging to characterize and the desired high resolution or analytical capabilities are limited. In line with our original goals to characterize battery reaction and degradation mechanisms under controlled electrochemical cycling, we developed a completely new type of Li-ion electrochemical cell that has been useful for both structural and analytical characterization. To date, we have demonstrated this platform for in-situ cycling of Li-ion batteries during scanning electron microscopy (SEM), Auger electron spectroscopy (AES), and x-ray photoelectron spectroscopy (XPS). In-situ AES has been found to be a quite powerful tool to characterize the chemical evolution of Li-ion batteries cycled in-situ and much of our effort in the final project period has focused on charactering Li-ion cathodes using the technique. We utilized in-situ SEM to propose a new mechanism for Li whisker/dendrite formation and show the importance of diffusion mediated stress relaxation in fracture of Sn anode particles. A combination of in-situ XPS and AES was used to clarify the CuO anode reaction mechanism. In the final project period, we have gained new insights into surface reactions occurring on cathodes at high voltage using in-situ AES. Specifically, we have discovered that many of the SEI formation reactions typically attributed to electrolyte decomposition are actually more fundamental to the electrode material surface thermodynamics in the presence of an arbitrary carbon source. These insights greatly affect how we understand and control surface degradation induced capacity fade at cathodes. Finally, we have made some effort to apply this novel in-situ platform to TEM characterization and believe this is a fruitful avenue for future research.

25 ENERGY STORAGE↗

Influence of Coronal Abundance Variations

The PI of this project was Jeff Scargle of NASA/Ames. Co-I's were Alma Connors of Eureka Scientific/Wellesley, and myself. Part of the work was subcontracted to Eureka Scientific via SAO, with Vinay Kashyap as PI. This project was originally assigned grant number NCC2-1206, and was later changed to NCC2-1350 for administrative reasons. The goal of the project was to obtain, derive, and develop statistical and data analysis tools that would be of use in the analyses of high-resolution, high-sensitivity data that are becoming available with new instruments. This is envisioned as a cross-disciplinary effort with a number of "collaborators" including some at SA0 (Aneta Siemiginowska, Peter Freeman) and at the Harvard Statistics department (David van Dyk, Rostislav Protassov, Xiao-li Meng, Epaminondas Sourlas, et al). We have developed a new tool to reliably measure the metallicities of thermal plasma. It is unfeasible to obtain high-resolution grating spectra for most stars, and one must make the best possible determination based on lower-resolution, CCD-type spectra. It has been noticed that most analyses of such spectra have resulted in measured metallicities that were significantly lower than when compared with analyses of high- resolution grating data where available (see, e.g., Brickhouse et al., 2000, ApJ 530,387). Such results have led to the proposal of the existence of so-called Metal Abundance Deficient, or "MAD" stars (e.g., Drake, J.J., 1996, Cool Stars 9, ASP Conf.Ser. 109, 203). We however find that much of these analyses may be systematically underestimating the metallicities, and using a newly developed method to correctly treat the low-counts regime at the high-energy tail of the stellar spectra (van Dyk et al. 2001, ApJ 548,224), have found that the metallicities of these stars are generally comparable to their photospheric values. The results were reported at the AAS (Sourlas, Yu, van Dyk, Kashyap, and Drake, 2000, BAAS 196, v32, #54.02), and at the conference on Statistical Challenges in Modem Astronomy (Sourlas, van Dyk, Kashyap, Drake, and Pease, 2003, SCMA 111, Eds. E.D.Feigelson, G.J.Babu, New York:Springer, p489-490). We also described the limitations of one of the most egregiously misused and misapplied statistical tests in astrophysical literature, the F-test for verifying model components (Protassov, van Dyk, Connors, Kashyap, and Siemiginowska, 2002, ApJ, 571,545). Indeed, a search through the ApJ archives turned up 170 papers in the 5 previous years that used the F-test explicitly in some form or the other, and with the vast majority of them not using it correctly! Indeed, looking at just 4 issues of the ApJ in 2001, we found 13 instances of its use, of which nine were demonstrably incorrect. Clearly, it is difficult to understate the importance of this issue. We also worked on speeding up Bayes Blocks and Sparse Bayes Blocks algorithms to make them more tractable for large searches. We also supported staistics students and postdocs in both explicit physics- model-based (spectra with tens of thousands of atomic lines) and "model-free" -- i.e. non-parametric or semi-parametric -- algorithms. Work on using more of the latter is just beginning; while using multi-scale methods for Poisson imaging has come to hition. In fact, "An Image Restoration Technique with Error Estimates", by D. Esch, A. Connors, M. Karovska, and D. van Dyk, was published by ApJ (Esch et a1.2004, ApJ, 610, 1213). The code has been delivered to M. Karovska for CXC; and is available for beta-testing upon request. The other large project we worked on was on the self-consistent modeling of logN-logs curves in the Poisson limit. logN-logs curves are a fundamental tool in the study of source populations, luminosity functions, and cosmological parameters. However, their determination is hampered by statistical effects such as the Eddington bias, incompleteness due to detection efficiency, faint source flux fluctuations, etc. We have develed a new and powerful method using the full Poisson machinery that allows us to model the logN-logs distribution of X-ray sources in a self-consistent manner. Because we properly account for all the above statistical effects, our modeling is valid over the full range of the data, and not just for strong sources, as is normally done. Using a Bayesian approach and modeling the fluxes with known functional forms such as simple or broken power-laws, and conditioning the expected photon counts on the fluxes, the background contamination, effective area, detector vignetting, and detection probability, we can delve deeply into the low counts regime and extend the usefulness of medium sensitivity surveys such as ChAMP by orders of magnitude. The built-in flexibility of the algorithm also allows a simultaneous analysis of multiple datasets. We have applied this analysis to a set a Chandra observations (Sourlas, Kashyap, Zezas, van Dyk, 2004, HEAD #8, #16.32)

Scargle, Jeffrey D.↗

Molecular Assemblies, Genes and Genomics Integrated Efficiently (MAGGIE)

Final report on MAGGIE. We set ambitious goals to model the functions of individual organisms and their community from molecular to systems scale. These scientific goals are driving the development of sophisticated algorithms to analyze large amounts of experimental measurements made using high throughput technologies to explain and predict how the environment influences biological function at multiple scales and how the microbial systems in turn modify the environment. By experimentally evaluating predictions made using these models we will test the degree to which our quantitative multiscale understanding wilt help to rationally steer individual microbes and their communities towards specific tasks. Towards this end we have made substantial progress towards understanding evolution of gene families, transcriptional structures, detailed structures of keystone molecular assemblies (proteins and complexes), protein interactions, biological networks, microbial interactions, and community structure. Using comparative analysis we have tracked the evolutionary history of gene functions to understand how novel functions evolve. One level up, we have used proteomics data, high-resolution genome tiling microarrays, and 5' RNA sequencing to revise genome annotations, discover new genes including ncRNAs, and map dynamically changing operon structures of five model organisms: For Desulfovibrio vulgaris Hildenborough, Pyrococcus furiosis, Sulfolobus solfataricus, Methanococcus maripaludis and Haiobacterium salinarum NROL We have developed machine learning algorithms to accurately identify protein interactions at a near-zero false positive rate from noisy data generated using tagfess complex purification, TAP purification, and analysis of membrane complexes. Combining other genome-scale datasets produced by ENIGMA (in particular, microarray data) and available from literature we have been able to achieve a true positive rate as high as 65% at almost zero false positives when applied to the manually curated training set. Applying this method to the data representing around a quarter of the fraction space for water soluble proteins in D. vulgaris, we obtained 854 reliable pair wise interactions. Further, we have developed algorithms to analyze and assign significance to protein interaction data from bait pull-down experiments and integrate these data with other systems biology data through associative biclustering in a parallel computing environment. We will 'fill-in' missing information in these interaction data using a 'Transitive Closure' algorithm and subsequently use 'Between Commonality Decomposition' algorithm to discover complexes within these large graphs of protein interactions. To characterize the metabolic activities of proteins and their complexes we are developing algorithms to deconvolute pure mass spectra, estimate chemical formula for m/z values, and fit isotopic fine structure to metabolomics data. We have discovered that in comparison to isotopic pattern fitting methods restricting the chemical formula by these two dimensions actually facilitates unique solutions for chemical formula generators. To understand how microbial functions are regulated we have developed complementary algorithms for reconstructing gene regulatory networks (GRNs). Whereas the network inference algorithms cMonkey and Inferelator developed enable de novo reconstruction of predictive models for GRNs from diverse systems biology data, the RegPrecise and RegPredict framework developed uses evolutionary comparisons of genomes from closely related organisms to reconstruct conserved regulons. We have integrated the two complementary algorithms to rapidly generate comprehensive models for gene regulation of understudied organisms. Our preliminary analyses of these reconstructed GRNs have revealed novel regulatory mechanisms and cis-regulatory motifs, as well asothers that are conserved across species. Finally, we are supporting scientific efforts in ENIGMA with data management solutions and by integrating all of the algorithms, software and data into a Knowledgebase. For instance, we have developed the RegPrecise database (http://regprecise.lbl.gov) which represents manually curated sets of regulons laying the basis for automatic annotation of regulatory interactions in closely related species. We are also in the midst of scaling up MicrobesOnline to handle the growing volume of sequence and functional genomics data. Over the last year our efforts have been focused on providing support for additional genomic and functional genomic data types. Similarly, we have developed several visualization tools to help with the exploration of complex systems biology datasets. A case in point is the Gaggle Genome Browser (GGB), which was enhanced with visualizations for plotting peptide detections and protein-DNA binding alongside transcriptome structure, plus the ability to interactively filter by signal intensity or p-value.

54 ENVIRONMENTAL SCIENCES↗

How initial conditions-, structural-, and parameter-based model uncertainty interact and influence predictions in permafrost ecosystems: Modeling Archive

This dataset contains model output and input data, as well as source code examples for the Terrestrial Ecosystem Model with the Dynamic Vegetation Model and Dynamic Organic Soil (DVM-DOS-TEM) for the field sites Imnavait creek and the Bonanza creek Long Term Ecological Research Network (LTER). The data covers simulations from the last glacial maximum (LGM) until 2100 for a selection of paleo scenarios, setting the mean temperature of the LGM up to 10°C lower than pre-industrial conditions. The model structure was modulated to represent various model versions, and this dataset contains the relevant changes in the source code. The raw output data, the processed statistical data, the setup and processing scripts as well as parameter value distribution files from a parameter sensitivity analysis are included as well. Model outputs include active layer depth, organic soil carbon, soil layer depths, gross primary productivity (GPP) with and without nitrogen limitation, net primary productivity (NPP), soil liquid water content, heterotrophic, maintenance, and growth respiration, soil temperature, and vegetation carbon (*.nc files). The Next-Generation Ecosystem Experiments in the Arctic (NGEE Arctic) project is a research effort to reduce uncertainty in the Department of Energy’s Energy Exascale Earth System Model (E3SM) by developing a predictive understanding of Arctic tundra ecosystems underlain by permafrost and to quantify feedbacks from the Arctic tundra to the Earth system. NGEE Arctic is supported by the Department of Energy's Office of Biological and Environmental Research.Over Phases 1–3, observations made by the NGEE Arctic team across a gradient of permafrost landscapes in Arctic Alaska improved the representation of tundra processes in the land surface component of E3SM (the E3SM Land Model, ELM). Model improvements emphasized unique aspects of permafrost environments and explored reductions in model complexity while retaining predictive power. The Arctic-informed ELM developed by NGEE Arctic has been used to make novel predictions on processes ranging from permafrost thaw to soil biogeochemical cycling to Earth system feedbacks associated with the unique characteristics of tundra plants. In Phase 4, the NGEE Arctic team is evaluating our new predictive understanding under novel conditions across the Arctic domain. In collaboration with partners at long-term pan-Arctic research sites we are examining whether an Arctic-informed ELM can faithfully simulate interactions among surface and subsurface processes at site, regional, and pan-Arctic scales. In turn, we are using variety of tools to dynamically extend and evaluate ELM inference, with an emphasis on data synthesis and pan-Arctic model evaluation, reintegration of code with an evolving E3SM, scaling across heterogeneous Arctic landscapes, and the appropriate representation of the impacts of increasingly frequent Arctic disturbances.

54 ENVIRONMENTAL SCIENCES↗

Satellite Collision Modeling with Physics-Based Hydrocodes: Debris Generation Predictions of the Iridium-Cosmos Collision Event and Other Impact Events

Satellite collision debris poses risks to existing space assets and future space missions. Predictive models of debris generated from these hypervelocity collisions are critical for developing accurate space situational awareness tools and effective mitigation strategies. Hypervelocity collisions involve complex phenomenon that spans several time- and length-scales. We have developed a satellite collision debris modeling approach consisting of a Lagrangian hydrocode enriched with smooth particle hydrodynamics (SPH), advanced material failure models, detailed satellite mesh models, and massively parallel computers. These computational studies enable us to investigate the influence of satellite center-of-mass (CM) overlap and orientation, relative velocity, and material composition on the size, velocity, and material type distributions of collision debris. We have applied our debris modeling capability to the recent Iridium 33-Cosmos 2251 collision event. While the relative velocity was well understood in this event, the degree of satellite CM overlap and orientation was ill-defined. In our simulations, we varied the collision CM overlap and orientation of the satellites from nearly maximum overlap to partial overlap on the outermost extents of the satellites (i.e, solar panels and gravity boom). As expected, we found that with increased satellite overlap, the overall debris cloud mass and momentum (transfer) increases, the average debris size decreases, and the debris velocity increases. The largest predicted debris can also provide insight into which satellite components were further removed from the impact location. A significant fraction of the momentum transfer is imparted to the smallest debris (< 1-5mm, dependent on mesh resolution), especially in large CM overlap simulations. While the inclusion of the smallest debris is critical to enforcing mass and momentum conservation in hydrocode simulations, there seems to be relatively little interest in their disposition. Based on comparing our results to observations, it is unlikely that the Iridium 33-Cosmos 2251 collision event was a large mass-overlap collision. We also performed separate simulations studying the debris generated by the collision of 5 and 10 cm spherical projectiles on the Iridium 33 satellite at closing velocities of 5, 10, and 15 km/s. It is important to understand the vulnerability of satellites to small debris threats, given their pervasiveness in orbit. These studies can also be merged with probabilistic conjunction analysis to better understand the risk to space assets. In these computational studies, we found that momentum transfer, kinetic energy losses due to dissipative mechanisms (e.g., fracture), fragment number, and fragment velocity increases with increasing velocity for a fixed projectile size. For a fixed velocity, we found that the smaller projectile size more efficiently transfers momentum to the satellite. This latter point has an important implication: Eight (spaced) 5 cm debris objects can impart more momentum to the satellite, and likely cause more damage, than a single 10 cm debris object at the same velocity. Further studies are required to assess the satellite damage induced by 1-5 cm sized debris objects, as well as multiple debris objects, in this velocity range.

42 ENGINEERING↗