Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Composite Bond Line Measurements Based on a Bayesian Analysis of Flash Thermography Data

For bonded composite materials, an accurate characterization of the adhesive bond line is needed to predict failure modes and fracture toughness. In this paper, bond line thickness was estimated from data obtained using through transmission flash thermography. The forward model that predicts back surface temperature is based on a three layer heat diffusion equation with varying diffusivity and flux boundary conditions. The corresponding inverse problem of estimating bond line thickness from measurement data was solved using a Bayesian approach that assumed Gaussian priors for the bond line thickness and thermal diffusivity of the adherends. Finally, the outputs of the thermography based method were compared to measurements that were collected using a micrometer and ultrasound testing.

Flash thermography↗

Prediction and evaluation of eddy-viscosity models for free mixing

Analysis for the turbulent mixing of free jets is presented in this paper and compared to recent experimental results. A turbulent mass diffusion model is presented and is based on the concentration potential core. The model yielded good results when compared with the experimental results except for low-speed flows where few experimental data are available. A review of recent experimental results verifies again that the three diffusion processes in turbulent mixing are interrelated; however, no single diffusion model may be used for all three processes. This is especially true when pressure gradients are present in the flow field. It is shown that even though momentum diffusion is significantly affected by pressure gradients, mass diffusion is not. It is further indicated that the mass diffusion model has been derived and is based on the accurate correlations of experimental results obtained for the concentration potential core. Similar techniques may be used in deriving an expression for the momentum and thermal diffusion coefficients. These expressions would be more complicated since they would have to take care of the boundary layer at the start of the mixing region. Finally, a comparison of the analyses, using this particular model and Ferri's model, with available experimental results is made.

Zakkay, V.↗

Thermal conductivity behavior of boron carbides

Knowledge of the thermal conductivity of boron carbides is necessary to evaluate its potential for high temperature thermoelectric energy conversion applications. The thermal diffusivity of hot pressed boron carbide B/sub 1-x/C/sub x/ samples as a function of composition, temperature and temperature cycling was measured. These data in concert with density and specific heat data yield the thermal conductivities of these materials. The results in terms of a structural model to explain the electrical transport data and novel mechanisms for thermal conduction are discussed.

Wood, C.↗

Three-dimensional modelling of horizontal chemical vapor deposition. I - MOCVD at atmospheric pressure

A systematic numerical study of the MOCVD of GaAs from trimethylgallium and arsine in hydrogen or nitrogen carrier gas at atmospheric pressure is reported. Three-dimensional effects are explored for CVD reactors with large and small cross-sectional aspect ratios, and the effects on growth rate uniformity of tilting the susceptor are investigated for various input flow rates. It is found that, for light carrier gases, thermal diffusion must be included in the model. Buoyancy-driven three-dimensional flow effects can greatly influence the growth rate distribution through the reactor. The importance of the proper design of the lateral thermal boundary conditions for obtaining layers of uniform thickness is emphasized.

Ouazzani, Jalil↗

Evaluations of Silicon Carbide Temperature Monitors

The effect of irradiation on materials properties is an important field of study for materials usage in both fission and fusion systems for energy production. Neutron flux and energy spectrums are well understood; however, the irradiation temperature can be more difficult to determine. Since the early 1960s, Silicon Carbide (SiC) has been used as a passive post-irradiation temperature monitor because the irradiation defects anneal out above the irradiation temperature. Irradiation temperature is determined by measuring a property change after isochronal annealing or during a continuously monitored annealing process. There are many properties that may be measured including electrical resistivity, bulk density, dimensions, thermal diffusivity, or lattice spacing. Electrical resistivity is accepted as a robust measurement technique; however, such method is time-consuming since the steps involved must be performed in a serial manner. The use of thermal expansion from continuous dilatometry is an automated process requiring minimal setup time. As part of a Nuclear Science User Facilities (NSUF) project, low dose silicon carbide monitors were irradiated in the BR2 material test reactor at SCK, Belgium, and were then evaluated at the Idaho National Laboratory (INL) High Temperature Test Laboratory (HTTL) to determine their peak temperature achieved during irradiation. The technical significance of this work was that the monitors were irradiated to a dose that was significantly less than recommended in published literature. This paper will discuss the evaluation processes available at HTTL and the performance of the low dose silicon carbide temperature monitors.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Microstructure, mechanical, and thermal properties of compositionally complex (Hf,Zr,Nb,Ti)B 2 ‒LaB 6 ceramics

Novel compositionally complex borides, (Hf,Zr,Nb,Ti)B 2 and (Hf,Zr,Nb,Ti)B 2 ‒LaB 6 , were fabricated using spark plasma sintering process. (Hf,Zr,Nb,Ti)B 2 ‒LaB 6 exhibits a dual-phase microstructure, in which (Hf,Zr,Nb,Ti)B 2 is a primary phase with the hexagonal structure and LaB 6 is a secondary phase with a cubic structure. The mechanical properties of both (Hf,Zr,Nb,Ti)B 2 and (Hf,Zr,Nb,Ti)B 2 ‒LaB 6 are comparable, with a combination of high hardness and moderate fracture toughness. Thermal diffusivity and conductivity of (Hf,Zr,Nb,Ti)B 2 are much lower than the individual transition metal borides but are significantly increased by the addition of LaB 6 . Herein, it is implied that the thermal properties of boride ceramics can be controlled through the appropriate design of principal metal element compositions.

borides↗

Linear viscous stability theory for stably stratified shear flow - A review.

In this paper the linear viscous stability theory for stably stratified parallel shear flow is reviewed and some new results are presented. Attention is focused on recent work on unbounded flows with emphasis placed on results which demonstrate apparent destabilizing effects of diffusivity which lie beyond the scope of inviscid theory. In particular it is shown that self-excited disturbances may exist with phase speeds lying outside the range of basic flow speed and that with strong thermal diffusivity, instability may occur even though the local Richardson number exceeds 0.25 throughout the flow.

Gage, K. S.↗

Effect of neutron irradiation on the thermoelectric properties of SiGe alloys

Zone-leveled and hot-pressed n- and p-type Si80Ge20 alloys were irradiated with neutrons to a fluence of 4 x 1018 n/sq cm and to a fluence of 5.4 x 1019 n/sq cm at a temperature of approximately 200-300 C. The effect of neutron irradiation on the thermoelectric properties of these alloys was evaluated. The carrier concentration and mobility (and hence the resistivity) were measured at room temperature while the thermal diffusivity was measured at 177-192 C both before and after the irradiation and after each subsequent 2-h heat treatment at 350 C, 600, and 1000 C. The irradiation increased the resistivity significantly, but the thermal conductivity decreased only by about 10-15 percent. This tends to indicate that the radiation produced only small defects (single pairs and small vacancy chains). The samples all returned to almost exactly their preirradiation state after the 1000 C anneal. This indicates that SiGe alloys can be operated in this neutron fluence at high temperatures without a degradation of thermoelectric properties.

Vandersande, Jan W.↗

Shadowgraph Study of Gradient Driven Fluctuations

A fluid or fluid mixture, subjected to a vertical temperature and/or concentration gradient in a gravitational field, exhibits greatly enhanced light scattering at small angles. This effect is caused by coupling between the vertical velocity fluctuations due to thermal energy and the vertically varying refractive index. Physically, small upward or downward moving regions will be displaced into fluid having a refractive index different from that of the moving region, thus giving rise to the enhanced scattering. The scattered intensity is predicted to vary with scattering wave vector q, as q(sup -4), for sufficiently large q, but the divergence is quenched by gravity at small q. In the absence of gravity, the long wavelength fluctuations responsible for the enhanced scattering are predicted to grow until limited by the sample dimensions. It is thus of interest to measure the mean-squared amplitude of such fluctuations in the microgravity environment for comparison with existing theory and ground based measurements. The relevant wave vectors are extremely small, making traditional low-angle light scattering difficult or impossible because of stray elastically scattered light generated by optical surfaces. An alternative technique is offered by the shadowgraph method, which is normally used to visualize fluid flows, but which can also serve as a quantitative tool to measure fluctuations. A somewhat novel shadowgraph apparatus and the necessary data analysis methods will be described. The apparatus uses a spatially coherent, but temporally incoherent, light source consisting of a super-luminescent diode coupled to a single-mode optical fiber in order to achieve extremely high spatial resolution, while avoiding effects caused by interference of light reflected from the various optical surfaces that are present when using laser sources. Results obtained for a critical mixture of aniline and cyclohexane subjected to a vertical temperature gradient will be presented. The sample was confined between two horizontal parallel sapphire plates with a vertical spacing of 1 mm. The temperatures of the sapphire plates were controlled by independent circulating water loops that used Peltier devices to add or remove heat from the room air as required. For a mixture with a temperature gradient, two effects are involved in generating the vertical refractive index gradient, namely thermal expansion and the Soret effect, which generates a concentration gradient in response to the applied temperature gradient. For the aniline/cyclohexane system, the denser component (aniline) migrates toward the colder surface. Consequently, when heating from above, both effects result in the sample density decreasing with altitude and are stabilizing in the sense that no convective motion occurs regardless of the magnitude of the applied temperature gradient. The Soret effect is strong near a binary liquid critical point, and thus the dominant effect is due to the induced concentration gradient. The results clearly show the divergence at low q and the predicted gravitational quenching. Results obtained for different applied temperature gradients at varying temperature differences from the critical temperature, clearly demonstrate the predicted divergence of the thermal diffusion ratio. Thus, the more closely the critical point is approached, the smaller becomes the temperature gradient required to generate the same signal. Two different methods have been used to generate pure concentration gradients. In the first, a sample cell was filled with a single fluid, ethylene glycol, and a denser miscible fluid, water, was added from below thus establishing a sharp interface to begin the experiment. As time went on the two fluids diffused into each other, and large amplitude fluctuations were clearly observed at low q. The effects of gravitational quenching were also evident. In the second method, the aniline/cyclohexane sample was used, and after applying a vertical temperature gradient for several hours, the top and bottom temperatures were set equal and the thermal gradient died on a time scale of seconds, leaving the Soret induced concentration gradient in place. Again, large-scale fluctuations were observed and died away slowly in amplitude as diffusion destroyed the initial concentration gradient.

Cannell, David↗

Transitions to chaos in two-dimensional double-diffusive convection

The partial differential equations governing two-dimensional thermosolutal convection in a Boussinesq fluid with free boundary conditions have been solved numerically in a regime where oscillatory solutions can be found. A systematic study of the transition from nonlinear periodic oscillations to temporal chaos has revealed sequences of period-doubling bifurcations. Overstability occurs if the ratio of the solutal to the thermal diffusivity tau is less than 1 and the solutal Rayleigh number Rs is sufficiently large. Solutions have been obtained for two representative values of tau. For tau = 0.316, R(s) = 10,000, symmetrical oscillations undergo a bifurcation to asymmetry, followed by a cascade of period-doubling bifurcations leading to aperiodicity, as the thermal Rayleigh number R(T) is increased. At higher values of R(T), the bifurcation sequence is repeated in reverse, restoring simple periodic solutions. As R(T) is further increased more period-doubling cascades, followed by chaos, can be identified. Within the chaotic regions there are narrow periodic windows, and multiple branches of oscillatory solutions coexist. Eventually the oscillatory branch ends and only steady solutions can be found. The development of chaos has been investigated for tau = 0.1 by varying R(T) for several different values of R(s). When R(s) is sufficiently small there are periodic solutions whose period becomes infinite at the end of the oscillatory branch. As R(s) is increased, chaos appears in the neighborhood of these heteroclinic orbits. At higher values of R(s), chaos is found for a broader range in R(T). A truncated fifth-order model suggest that the appearance of chaos is associated with heteroclinic bifurcations.

Knobloch, E.↗

Numerical simulation of cometary nuclei. III - Internal temperatures of cometary nuclei

The thermal diffusion equation for the internal temperature of cometary nuclei is exactly solved by means of a one-dimensional numerical model in order to shed light on the complex behavior of these temperatures with varying orbital and thermal parameters and in order to consider possible cometary nucleus thermal evolution targets for comet rendezvous and/or sample-return missions. The concept of 'new' and 'old' comets, classified in terms of how many passages around the sun have been made, may take on new meaning in view of the present demonstration that differences in eccentricity between two comets having the same period and number of apparitions may yield significantly different internal temperature profiles.

Herman, Gary↗

Effects of a temperature-dependent rheology on large scale continental extension

The effects of a temperature-dependent rheology on large-scale continental extension are investigated using a thin viscous sheet model. A vertically-averaged rheology is used that is consistent with laboratory experiments on power-law creep of olivine and that depends exponentially on temperature. Results of the calculations depend principally on two parameters: the Peclet number, which describes the relative rates of advection and diffusion of heat, and a dimensionless activation energy, which controls the temperature dependence of the rheology. At short times following the beginning of extension, deformation occurs with negligible change in temperature, so that only small changes in lithospheric strength occur due to attenuation of the lithosphere. However, after a certain critical time interval, thermal diffusion lowers temperatures in the lithosphere, strongly increasing lithospheric strength and slowing the rate of extension. This critical time depends principally on the Peclet number and is short compared with the thermal time constant of the lithosphere. The strength changes cause the locus of high extensional strain rates to shift with time from regions of high strain to regions of low strain. Results of the calculations are compared with observations from the Aegean, where maximum extensional strains are found in the south, near Crete, but maximum present-day strain rates are largest about 300 km further north.

Sonder, Leslie J.↗

Effects of a temperature-dependent rheology on large-scale continental extension

The effects of a temperature-dependent rheology on large-scale continental extension are investigated using a thin viscous sheet model. A vertically-averaged rheology is used that is consistent with laboratory experiments on power-law creep of olivine and that depends exponentially on temperature. Results of the calculations depend principally on two parameters: the Peclet number, which describes the relative rates of advection and diffusion of heat, and a dimensionless activation energy, which controls the temperature dependence of the rheology. At short times following the beginning of extension, deformation occurs with negligible change in temperature, so that only small changes in lithospheric strength occur due to attenuation of the lithosphere. However, after a certain critical time interval, thermal diffusion lowers temperatures in the lithosphere, strongly increasing lithospheric strength and slowing the rate of extension. This critical time depends principally on the Peclet number and is short compared with the thermal time constant of the lithosphere. The strength changes cause the locus of high extensional strain rates to shift with time from regions of high strain to regions of low strain. Results of the calculations are compared with observations from the Aegean, where maximum extensional strains are found in the south, near Crete, but maximum present-day strain rates are largest about 300 km further north.

Sonder, Leslie J.↗

Thermal effects of insolation propagation into the regoliths of airless bodies

The planetary surface thermal models used in the present study are composed of particles which, while bright and optically thin in the visual, are dark and opaque in the thermal IR. It is assumed that insolation is absorbed over a finite regolith distance whose scale length relative to diurnal skin depth for thermal diffusion can be substantial. Attention is given to the lower daytime and higher nighttime temperatures predicted by comparison with models assuming absorption only at the surface. It is noted that, with sufficiently deep penetration of insulation and high thermal IR particle opacity, a solid-state greenhouse can result.

Brown, Robert Hamilton↗

Diffusion and viscosity coefficients for helium

The first order Boltzmann-Fokker-Planck equation is solved numerically to obtain diffusion and viscosity coefficients for a ternary gas mixture composed of electron, protons, and helium. The coefficients are tabulated for five He/H abundances ranging from 0.01 to 10 and for both He II and He III. Comparison with Burgers's thermal diffusion coefficients reveals a maximum difference of 9-10% for both He II and He III throughout the range of helium abundances considered. The viscosity coefficients are compared to those of Chapman and Cowling and show a maximum difference of only 5-6% for He II but 15-16% for He III. For the astrophysically important gas mixtures, it is concluded that the results of existing studies which employed Burgers's or Chapman and Cowling's coefficients will remain substantially unaltered.

Roussel-Dupre, R.↗

Thermal conductivity of boron carbides

Knowledge of the thermal conductivity of boron carbide is necessary to evaluate its potential for high-temperature thermoelectric energy conversion applications. Measurements have been conducted of the thermal diffusivity of hot-pressed boron carbide BxC samples as a function of composition (x in the range from 4 to 9), temperature (300-1700 K), and temperature cycling. These data, in concert with density and specific-heat data, yield the thermal conductivities of these materials. The results are discussed in terms of a structural model that has been previously advanced to explain the electronic transport data. Some novel mechanisms for thermal conduction are briefly discussed.

Wood, C.↗

Refined Sensitivity Estimates for Single-Molecule Magnet Dark Matter Detectors

We revisit the sensitivity of Single Molecule Magnet (SMM) crystals as detectors for low-mass dark matter. In previous work, we established the concept of the ``magnetic bubble chamber'', where energy deposited by dark matter triggers a magnetic avalanche in a metastable crystal. The original sensitivity estimates relied on a conservative criterion requiring the spin relaxation time to be strictly shorter than the thermal diffusion time. Here, we demonstrate that this criterion effectively ignores the stochastic nature of spin relaxation. We derive a refined analytic estimate which accounts for the fraction of spins that relax even when diffusion is fast. We show that the Zeeman energy released by this fraction contributes to local heating, significantly lowering the energy threshold for avalanche formation. We present simulation results confirming this effect and report on experimental verification of the assumed low-temperature thermal properties of two representative SMM crystals, Mn$_{12}$-acetate and Mn$_{32}$. Together, these efforts extend this pathfinder program toward the realization of SMM-based detectors with controlled material properties and enhanced dark matter sensitivity.

Eberhardt, Andrew [Tokyo U., IPMU]↗