Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface roughness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

The Turbulent Boundary Layer on a Rough Curvilinear Surface

A number of semiempirical approximate methods exist for determining the characteristics of the turbulent boundary layer on a curvilinear surface. At present, among these methods, the one proposed by L. G. Loitsianskii is given frequent practical application. This method is sufficiently effective and permits, in the case of wing profiles with technically smooth surfaces, calculating the basic characteristics of the boundary layer and the values of the overall drag with an accuracy which suffices for practical purposes. The idea of making use of the basic integral momentum equation ((d delta(sup xx))/dx) + ((V' delta(sup xx))/V) (2 + H) = (tau(sub 0))/(rho V(exp 2)) proves to be fruitful also for the solution of the problems in the determination of the characteristics of the turbulent boundary layer on a rough surface.

Droblenkov, V. F.↗
NASA NTRS1994

Surface energy changes produced by ultraviolet-ozone irradiation of poly(methylmethacrylate), polycarbone and polytetrafluoroethylene

Contact angles of water and methylene iodide were measured as a function of UV/O3 treatment time for three polymers: poly(methylmethacrylate) (PMMA), polycarbonate, and polytetrafluoroethylene (PTFE). Surface roughnesses were also measured. Surface free energies were then calculated using relationships developed by Kaelble and Neumann. The surface energy of polycarbonate was found to increase (60 percent) during UV/O3 treatment. However, calculations on PMMA were hampered by the formation of a water soluble surface product. On PTFE surfaces, the UV/O3 treatment etched the surface causing large increases in surface roughness, rendering contact angle measurements impossible. It is concluded that care must be taken in interpreting contact angle measurements and surface energy calculations on UV/O3 treated polymer surfaces.

Ponter, A. B.↗
NASA NTRS1977

Microwave remote sensing and its application to soil moisture detection

The author has identified the following significant results. Experimental measurements were utilized to demonstrate a procedure for estimating soil moisture, using a passive microwave sensor. The investigation showed that 1.4 GHz and 10.6 GHz can be used to estimate the average soil moisture within two depths; however, it appeared that a frequency less than 10.6 GHz would be preferable for the surface measurement. Average soil moisture within two depths would provide information on the slope of the soil moisture gradient near the surface. Measurements showed that a uniform surface roughness similar to flat tilled fields reduced the sensitivity of the microwave emission to soil moisture changes. Assuming that the surface roughness was known, the approximate soil moisture estimation accuracy at 1.4 GHz calculated for a 25% average soil moisture and an 80% degree of confidence, was +3% and -6% for a smooth bare surface, +4% and -5% for a medium rough surface, and +5.5% and -6% for a rough surface.

Newton, R. W.↗
NASA NTRS2003

Kinetic Monte Carlo Simulations of Rod Eutectics and the Surface Roughening Transition in Binary Alloys

In this paper we report on two related topics: Kinetic Monte Carlo simulations of the steady state growth of rod eutectics from the melt, and a study of the surface roughness of binary alloys. We have implemented a three dimensional kinetic Monte Carlo (kMC) simulation with diffusion by pair exchange only in the liquid phase. Entropies of fusion are first chosen to fit the surface roughness of the pure materials, and the bond energies are derived from the equilibrium phase diagram, by treating the solid and liquid as regular and ideal solutions respectively. A simple cubic lattice oriented in the {100} direction is used. Growth of the rods is initiated from columns of pure B material embedded in an A matrix, arranged in a close packed array with semi-periodic boundary conditions. The simulation cells typically have dimensions of 50 by 87 by 200 unit cells. Steady state growth is compliant with the Jackson-Hunt model. In the kMC simulations, using the spin-one Ising model, growth of each phase is faceted or nonfaceted phases depending on the entropy of fusion. There have been many studies of the surface roughening transition in single component systems, but none for binary alloy systems. The location of the surface roughening transition for the phases of a eutectic alloy determines whether the eutectic morphology will be regular or irregular. We have conducted a study of surface roughness on the spin-one Ising Model with diffusion using kMC. The surface roughness was found to scale with the melting temperature of the alloy as given by the liquidus line on the equilibrium phase diagram. The density of missing lateral bonds at the surface was used as a measure of surface roughness.

Bentz, Daniel N.↗
NASA NTRS1978

A Radiative Transfer Model for Microwave Emission from Soils

The radiative transfer equation for an absorbing medium is used to develop a model for microwave emission from soils. The model calculates the microwave emission intensity in terms of the brightness temperature as a function of the soil moisture and temperature. The consistency of the model is verified by a comparative study of the present model with other microwave emission models. The effect of surface roughness on the brightness temperature is studied by modifying the Fresnel reflection coefficient and by including the surface depolarization effect. The quantitative effect of the surface roughness is studied and it is demonstrated that the brightness temperatures observed for a natural agricultural terrain can be explained through the inclusion of the roughness effect. The surface roughness effect is further analyzed to obtain formulae which are useful in the analysis of the brightness temperatures, particularly, to obtain soil moisture information from the brightness. temperatures. The sensitivity of the brightness temperature to the soil temperature variations is studied both qualitatively and quantitatively. A simple formula is obtained to calculate the soil temperature dependence of the brightness temperature in terms of the surface and the deep soil temperatures. An algorithm to normalize the brightness temperatures so as to compare microwave observations under different soil temperature conditions is also discussed. A program listing of the model is given in the appendix.

Choudhury, B. J.↗
NASA NTRS1978

Radar observations of a volcanic terrain: Askja Caldera, Iceland

Surface roughness spectra of nine radar backscatter units in the Askja caldera region of Iceland were predicted from computer-enhanced like- and cross-polarized radar images. A field survey of the caldera was then undertaken to check the accuracy of the preliminary analysis. There was good agreement between predicted surface roughness of backscatter units and surface roughness observed in the field. In some cases, variations in surface roughness could be correlated with previously mapped geologic units.

Evans, D. L.↗
NASA NTRS1965

Scattering theories and radar return

Scattering theories and radar return - theory of bistatic radar return from statistically rough surface and literature survey on scattering theories

SURFACE ROUGHNESS↗
NASA NTRS1971

Metal-silicate friction in ultrahigh vacuum

Results of the analysis and experiments on the frictional behavior of materials under conditions of ultrahigh vacuum, as related to kinematic problems in a lunar environment, are presented. Experiments have been performed under varying conditions of cleanliness to determine frictional characteristics at 10 to the minus 7th power to 10 to the minus 8th power torr between flat basalt and spherical 7075-T6 aluminum surfaces. A quantitative analysis has been made of the factors influencing frictional behavior of these materials. The proposed mathematical model incorporated parameters of surface cleanliness, surface roughness, and surface energy.

Ofodile, E. I.↗
NASA NTRS1980

The structure of moderately strong winds at a mid-Atlantic coastal site /below 75m/

Velocity and temperature measurements were obtained from an instrumented 76-meter meteorological tower located near the Atlantic Ocean at Wallops Island, Virginia. The instrumentation consists of a slow-response cup-vane and resistance temperature system and a hot-film, thermocouple system for turbulence measurements. Results are presented for moderately strong winds from westerly directions (category I) and for on-shore winds from southerly directions (category II). Results from category I winds indicate the presence of low-frequency velocity fluctuations affecting all turbulence parameters similar to the observations made in Kansas and Minnesota. Winds of category II experience a change in surface roughness and surface temperature as they cross the coast line, resulting in the development of an internal boundary layer. The stable ocean air above the IBL shows extremely low turbulence levels (less than 3%). Because of the lack of turbulent mixing with adjacent layers, Coriolis effects are important and profiles with a maximum velocity at heights between 60-200 m exist.

Tieleman, H. W.↗
NASA NTRS1984

Performance of thermal barrier coatings in high heat flux environments

Thermal barrier coatings were exposed to the high temperature and high heat flux produced by a 30 kW plasma torch. Analysis of the specimen heating rates indicates that the temperature drop across the thickness of the 0.038 cm ceramic layer was about 1100 C after 0.5 sec in the flame. An as-sprayed ZrO2-8%Y2O3 specimens survived 3000 of the 0.5 sec cycles with failing. Surface spalling was observed when 2.5 sec cycles were employed but this was attributed to uneven heating caused by surface roughness. This surface spalling was prevented by smoothing the surface with silicon carbide paper or by laser glazing. A coated specimen with no surface modification but which was heat treated in argon also did not surface spall. Heat treatment in air led to spalling in as early as 2 cycle from heating stresses. Failures at edges were investigated and shown to be a minor source of concern. Ceramic coatings formed from ZrO2-12%Y2O3 or ZrO2-20%Y2O3 were shown to be unsuited for use under the high heat flux conditions of this study.

Miller, R. A.↗
NASA NTRS1984

A fundamental approach to the sticking of insect residues to aircraft wings

A proposed testing scheme is described for obtaining data on the effects of surface roughness and surface energy on insect adhesion. The road test apparatus is discussed as well as surface preparation techniques. Uncoated and polymer coated metal substrates were analyzed by SEM/ESCA/IRS before and following collision with insects. Critical surface tensions of unexposed Nyebar and poly sulfone coatings were 10 and 33 dynes/cm, respectively, as determined from contact angles. A total of 95% of insect residues collected belong to order Diptera. Significantly less insect debris was detected on the coated plates as compared to the uncoated plates. Minimal contamination at the 5 nm level of both coated and uncoated plates occurs even after hours of exposure to road conditions as determined by ESCA analysis. The presence of nitrogen detected by ESCA on exposed plates is unequivocal evidence for insect residues left on plates.

Eiss, N. S., Jr.↗
NASA NTRS1984

Performance of thermal barrier coatings in high heat flux environments

Thermal barrier coatings were exposed to the high temperature and high heat flux produced by a 30 kW plasma torch. Analysis of the specimen heating rates indicates that the temperature drop across the thickness of the 0.038 cm ceramic layer was about 1100 C after 0.5 sec in the flame. An as-sprayed ZrO2-8 percent Y2O3 specimens survived 3000 of the 0.5 sec cycles with falling. Surface spalling was observed when 2.5 sec cycles were employed but this was attributed to uneven heating caused by surface roughness. This surface spalling was prevented by smoothing the surface with silicon carbide paper or by laser glazing. A coated specimen with no surface modification but which was heat treated in argon also did not surface spall. Heat treatment in air led to spalling in as early as 1 cycle from heating stresses. Failures at edges were investigated and shown to be a minor source of concern. Ceramic coatings formed from ZrO2-12 percent Y2O3 or ZrO2-2O percent Y2O3 were shown to be unsuited for use under the high heat flux conditions of this study.

Miller, R. A.↗
NASA NTRS1984

Performance of thermal barrier coatings in high heat flux environments

Thermal barrier coatings were exposed to the high temperature and high heat flux produced by a 30 kW plasma torch. Analysis of the specimen heating rates indicates that the temperature drop across the thickness of the 0.038 cm ceramic layer was about 1100 C after 0.5 sec in the flame. An as-sprayed ZrO2-8 percent Y203 specimens survived 3000 of the 0.5 sec cycles with failing. Surface spalling was observed when 2.5 sec cycles were employed but this was attributed to uneven heating caused by surface roughness. This surface spalling was prevented by smoothing the surface with silicon carbide paper or by laser glazing. A coated specimen with no surface modification but which was heat treated in argon also did not surface spall. Heat treatment in air led to spalling in as early as 2 cycle from heating stresses. Failures at edges were investigated and shown to be a minor source of concern. Ceramic coatings formed from ZrO2-12 percent Y2O3 or ZrO2-20 percent Y2O3 were shown to be unsuited for use under the high heat flux conditions of this study.

Miller, R. A.↗
NASA NTRS1987

Pressure-Assisted Seal for Castings

Modification of widely used pressure-assisted gasket ensures tight seal even when one sealed surface somewhat rough or porous. Modified U-cross-section gasket has thin lips increasing sealing area and conform to slightly rough surface. Lips provide wider sealing area and extend highly loaded region at tip. Coating of polytetrafluoroethylene on tip and lip augments conformance.

Stuck, Donald E.↗
NASA NTRS1987

The physical basis for estimating wave energy spectra from SAR imagery

Ocean surface waves are imaged by synthetic aperture radar (SAR) through a combination of the effects of changes in the surface slope, surface roughness, and surface motion. Over a limited range of conditions, each of these effects can be described in terms of a linear modulation-transfer function. In such cases, the wave-height spectrum can be estimated in a straightforward manner from the SAR image-intensity spectrum. The range of conditions over which this assumption of linearity is valid is investigated using a numerical simulation model, and the implications of various departures from linearity are discussed.

Lyzenga, David R.↗
NASA NTRS1990

Investigation of air transportation technology at the Massachusetts Institute of Technology, 1988-1989

There are four areas of research being pursued in 1988 under sponsorship of the FAA/NASA Joint University Research Program, and one area which has been completed. The four active areas were: (1) Automatic Speech Recognition (ASR) in Air Traffic Control. The purpose of this research effort is to demonstrate the feasibility of using ASR technology within the ATC environment and to address the problems involved, especially the relevant human factors issues. (2) A Rule-Based Planning and Scheduling System. Planning denotes the formulation of a detailed scheme, program, or method worked out beforehand for the accomplishment of a goal. It involves the analysis of the desired goal and its division into sub-goals which are subsequently treated in the same way until a set of primitive objectives is obtained. (3) Modeling of Ice Accretion on Aircraft in Glaze Icing Conditions. The work in aircraft icing over the past year has focused on the fundamental aspects of glaze ice accretion, with the goal of improving analytical ice accretion models. Over the past year, studies have been conducted on the generation of surface roughness on accreting ice surfaces with the goal of providing a deterministic surface roughness in the ice accretion models. (4) Cockpit Display of Hazardous Weather Information. Information transfer and display issues associated with the dissemination of hazardous weather warnings are studied in the context of windshear alerts.

Simpson, Robert W.↗