Results for “sub scale” — Page 21

NASA NTRSDate not supplied

Evaluation of CFD Predictions of CobraMRV Control Surface Effectiveness at the NASA Langley Unitary Plan Wind Tunnel

The ability of CFD simulations to serve as a surrogate for wind tunnel testing at high supersonic speeds has been evaluated for a sub-scale model of the Co-Optimization Blunt-body Re-entry Analysis-Mid-lift-to-drag Rigid Vehicle (CobraMRV) human Mars entry vehicle concept. The vehicle was tested at the Unitary Plan Wind Tunnel (UPWT) at the NASA Langley Research Center under flow conditions and surface control configurations relevant to the entry stage of a flight mission. The CFD simulations were performed prior to gaining access to test results in order to assess how blind predictions obtained using best practices compare to experiments. Solutions of empty tunnel simulations were used as inflow boundary condition for the CobraMRV simulations in a truncated portion of the test section. Different solvers and turbulence models were used by separate teams to assess sensitivity to numerical methods, physics, and users. After release of the test results, the pre-test computations were compared to the experimental results, and additional analyses have been conducted to explain observed discrepancies. The amount of time and resources dedicated to each phase of the computational work was logged for comparison to that required for wind tunnel tests, and to inform planning of future CFD data base development projects.

ARMD↗

NASA NTRSDate not supplied

Large Vehicle Lunar Landing Surface Interaction and In-Situ Resource Based Risk Mitigation: Landing & Launch Pads

A key capability required for the exploration of planetary bodies is the ability to land on the surface. Previous work performed by NASA and other institutions has primarily focused on landing small spacecraft on planetary surfaces and the associated small-to-medium thrusters required for the soft landing. In the case of human exploration—particularly the establishment of long duration exploration and habitation outposts—the ability to land large landers, such as the SpaceX Starship, is necessary. These larger landing systems require the use of more powerful engines, with higher engine exhaust temperatures and higher landing loads. Understanding the excavation of material by the engines, as well as the potential for the landing legs to sink into the subsurface, is key in ensuring reliable and safe landings. A further improvement in landing reliability can be achieved by constructing landing / launch pads, especially with in-situ resources. Some material excavation by the plume is inevitable, leaving at least a portion of the surface scoured and uneven under the lander and ejecting regolith particles and rocks at very high velocities. One possible solution would be to robotically build landing / launch pads (ideally autonomously) at the destination using in-situ materials. In this case, the first one or few landers will need to land on unimproved surfaces at higher risk; however, they would bring the required equipment to build the landing pads with mostly local resources, thus increasing the reliability of safe landing for subsequent larger landers. A number of methods to build in-situ landing and launch pads have already been developed. These methods include no, or some, addition of required binder additives to the local regolith material, different processing approaches and result in varying landing pad strengths. A sub-scale rocket engine plume, was used to simulate some of the conditions of a landing on the Moon to assess the effectiveness of various materials for an in-situ built landing pad, The GO2/GCH4rocket engine fired on a 1m2area coupons of representative pad materials. The results will allow continued development towards materials that satisfy the landing pad properties required for the effective risk reduction and increased reliability for landing people and equipment on the lunar surface. This work contained two parts: (1) computer modeling of a large rocket engine plume interacting with regolith on the Moon, using the Granular Gas Flow Solver (GGFS) provided by CFD Research Corporation as well as other computational fluid dynamics codes (CFD) such as Loci/CHEM. (2) Developing landing/launch pad materials that could be used for in-situ construction on the lunar surface in the future, to mitigate the calculated effects of a large vehicle rocket engine landing and launching on the Moon.

Lunar↗

NASA NTRS2020

Validation of Diffraction Models With Experimental Results From the Princeton Starshade Testbed

Starshades are a leading technology to detect and characterize Earth-like exoplanets. In this paper we report on optical experiments of sub-scale starshades that advance critical starlight suppression technologies in preparation for the next generation of space telescopes. These experiments were conducted at the Princeton starshade testbed, an 80 m long enclosure testing 1/1000th scale starshades at a ight-like Fresnel number. In this paper we summarize recent updates made to the starshade testbed and optical model. We present results from recent experiments testing two starshade masks with intentional perturbations built into their shape. One of the perturbed masks has three petals that are shifted radially outward by 7-11 microns and the other mask has two petals shifted radially outward plus two petal edge segments displaced from their nominal position. We show the model agrees with experiment to better than 25% accuracy. These results are placed into context with previous experiments on perturbed shapes and progress made towards satisfying a critical milestone in advancing starshade technology to TRL 5.

Galvin, Michael↗

NASA NTRSDate not supplied

Lunar Dust Tolerance Testing of Representative Seals for Lunar Surface Hatch Seals

The Moon’s surface creates a uniquely challenging environment for mechanisms and materials. Electrostatic adhesion combined with a jagged particulate morphology makes lunar dust particularly destructive to the components and sub-systems of lunar surface assets. One component that will be acutely impacted by lunar dust is seals, particularly those on the hatches which will be opened and closed to allow extravehicular activities (EVA) and on docking systems that will connect surface assets and spacecraft together. Lunar dust on these seals can create leak paths for the pressurized atmosphere of a surface asset to escape. Quantifying the level of lunar dust contamination that is allowable for seals is of paramount importance for mission planners and asset designers. This paper covers dust tolerance testing that was conducted on representative hatch seals with the Uniform Dust Deposition System (UDDS) at NASA Glenn Research Center [1]. Sub scale (≈30 cm diameter) versions of seals for the Orion docking hatch and NASA Docking System (NDS were coated evenly with varying amounts of lunar dust simulant to evaluate its effect on seals leak rates. The resulting leak rate results from these flight-proven seal design can help planners and designers construct robust missions and products

N. Jimenez↗

NASA NTRSDate not supplied

Advanced Composite Solar Sail System (ACS3) Mission Update

The Advanced Composite Solar Sail System (ACS3) will be the first practical solar sail for the National Aeronautics and Space Administration. [1] ACS3 will also be the first spaceflight demonstration of NASA compact deployable composite boom technology.[2] The primary mission objective of ACS3 will be to deploy and characterize an 80-m2 composite boom structure solar sail technology in low Earth orbit. Extended mission goals will be to demonstrate controlled solar sailing flight via a series of orbit raising and lowering maneuvers. Target mission orbit is a 1000 km x 1000 km midnight-noon sun-synchronous orbit. Launch of ACS3 is scheduled for July 2023 with sail deployment in September 2023. Mission duration is expected to be six to nine months. The ACS3 solar sail vehicle is a 12U Cubesat consisting of a bus module, containing flight and solar sail control avionics, and a solar sail module, containing the composite booms and metallized polymer solar sail membranes of the solar sail structure stowed within a boom deployer mechanism. A four-camera instrument suite for 360-degree imaging of the ACS3 solar sail during and after deployment is also housed within the bus module. The ACS3 80-m2 solar sail design is a sub-scale version of an intermediate-size 500-m2 solar sail using NASA deployable composite boom technology. The sail consists of four metallized 2-m thick polyethylene naphthalate (PEN) 20-m2 triangular quadrants supported by four 7-m long lenticular cross-section composite booms. Booms are flattened and co-coiled for stowage within a tape-spool driven deployer mechanism. Total mass of the ACS3 space vehicle including solar sail is 16 kg. An overview of the ACS3 mission and mission systems will be provided in this presentation. This overview will include descriptions of the solar sail structures and materials technology used with ACS3, and discussion of the scalability and extensibility of the ACS3 solar sail to future larger-scale solar sailing mission requirements. An update on progress towards the launch of ACS3 in July 2023 will also be provided. References [1] https://www.nasa.gov/directorates/spacetech/small_spacecraft/ACS3 [2] https://www.nasa.gov/directorates/spacetech/game_changing_development/projects/dcb

Solar sail↗

NASA NTRSDate not supplied

Selection, Production, and Properties of Regolith Polymer Composites for Lunar Construction

NASA’s Artemis Program seeks to establish a long-term presence on the moon to enable scientific discoveries and utilization of lunar resources through public-private partnerships. Over the next decades, a lunar spaceport enabling regular transportation from and to Earth will need to be established to provide the services and facilities that are necessary to achieve this goal. Robotic construction technologies using in-situ materials must be developed to build up enabling infrastructure such as launch/landing pads, blast protection, power/communications towers, improved trafficability pathways and radiation protection shelters. Kennedy Space Center’s Granular Mechanics and Regolith Operations laboratory at Swamp Works has partnered with AI SpaceFactory to develop the architectural and structural design of an unpressurized shelter. The shelter, called Lina, is designed to protect astronauts and surface assets from radiation, meteoroid impact, moon quakes and thermal gradients. Lina’s structural design criteria and the resulting structure design are detailed in separate papers. A Fused Filament Fabrication (FFF) construction process using regolith polymer composites has been developed. This paper presents the material formulations and selection rationale for each of the composite components. Formulations include 70:30, 80:20, and 85:15 wt.% mixture ratios of lunar mare simulant Black Point-1 (BP-1): Polylactic Acid (PLA), 80:20 Lunar Highlands Simulant (LHS-1): PLA and an 80:20 BP-1:PLA formulation with a processing aid/compatibilizer additive. Test samples were printed in simulated lunar dirty thermal vacuum conditions (~-180 °C, ~10 -3 torr). The test environment evolved throughout the duration of the print process. A series of tests were performed to characterize the mixture ratios achieved for each formulation, the off-gassing products during vacuum printing, the strength properties, and porosity of printed products. The LHS-1: PLA formulation yielded an advantageous combination of properties and was used in a final test that additively constructed a sub-scaled Lina on regolith simulant in dirty vacuum conditions.

lunar infrastructure↗

NASA NTRS2023

Assessing Flow Formability of Aerospace Aluminum Alloys via DIC Tensile Testing

Over the past decade, NASA Langley Research Center (LaRC) has championed integrally stiffened cylinder (ISC) technology for single-piece, cryogenic tank barrels on launch vehicles. The current investigation aims to extend the hybrid spin/shear/flow forming process to aircraft fuselage structures, a damage tolerance critical application. The WF Maschinenbau VUD-600® vertical spin/flow forming facility recently established at LaRC represents a reasonable sub-scale facsimile of the ISC deformation process for research and development (R&D) purposes. The objective of this study is to explore whether tensile testing with digital image correlation (DIC) is an effective way to rank the formability of candidate aerospace Al alloys and expedite empirical forming trials. Specific tensile data, such as reduction of area, strain hardening exponent, and modulus of resilience, are used as formability metrics for a variety of alloy/temper/product form combinations. Results from high-strength aluminum alloys AA 2139, AA 2050, AA 2043 and AA 2219 are compared with the medium-strength, highly formable AA 6061 benchmark. Rolled, forged and cast preform materials in both the -O temper (fully annealed) and -T4 temper (solution-treated, quenched, and naturally aged) conditions are evaluated. AA 2139 plate in the -T4 temper emerges as the top-ranked material, based on the criteria selected. Starting with preforms in the -T4 temper will result in flow-formed material exhibiting mechanical properties closer to aircraft fuselage requirements. The optimum balance between strength and damage tolerance may also be achieved via post-forming procedures that avoid quenching and stretching.

Aluminum alloys↗

NASA NTRSDate not supplied

Selection, Production, and Properties of Regolith Polymer Composites for Lunar Construction

NASA’s Artemis Program seeks to establish a long-term presence on the Moon to enable scientific exploration and expand the cis-lunar economy by utilizing lunar resources through public-private and international partnerships. Over the next decades, a lunar spaceport will need to be established to provide the services and facilities that are necessary to achieve this goal. Robotic construction technologies using in-situ materials must be developed to build up enabling infrastructure such as launch/landing pads, blast protection, power/communications infrastructure, improved roads, improved operational surfaces, and radiation protection shelters. Kennedy Space Center’s Granular Mechanics and Regolith Operations laboratory at Swamp Works has partnered with SpaceFactory and LERA Consulting Structural Engineers to develop the architectural and structural design of an unpressurized lunar shelter. The shelter, called Lunar Infrastructure Asset (LINA), is designed to support 2.3 m of regolith overburden to protect astronauts and surface assets from radiation, meteoroid impact, thermal gradients/cycling, and to withstand moonquakes. LINA’s structural design criteria and the resulting structure design are detailed in separate papers. A Fused Filament Fabrication (FFF) construction process using regolith polymer composites has been developed and is detailed in a separate publication. This paper presents material formulations and selection rationale for each of the composite components that were examined. Formulations include 70:30, 80:20, and 85:15 wt.% mixture ratios of lunar mare simulant Black Point-1 (BP-1): Polylactic Acid (PLA), 80:20 Lunar Highlands Simulant-1 (LHS-1): PLA and an 80:20 BP-1: PLA formulation with a flow enhancer additive. Test samples were printed in simulated lunar dirty thermal vacuum conditions (-190 °C, 10-3 torr). A series of tests were performed on each formulation to characterize the achieved mixture ratio, mechanical strength properties, off-gassing products during vacuum printing, and porosity and density of printed products. The LHS-1: PLA formulation yielded an advantageous combination of properties and was used in a final test that additively constructed a sub-scaled LINA on regolith simulant in dirty vacuum conditions. The materials and construction process presented in this paper are considered to be at Technology Readiness Level (TRL) 5 with additional testing necessary to characterize long term lunar environmental exposure effects.

lunar infrastructure↗

NASA NTRSDate not supplied

Design for an Integrated Open-Loop System for Carbon Dioxide Removal using Liquid Amine

Manned Space missions require maintaining a safe environment for the crew that can both sustain a breathable atmosphere and remove pollutants. Carbon dioxide, while not toxic in low concentrations, accumulates as crew members work and breath and can eventually affect the crew’s health. Therefore, a constant, passive system to remove the carbon dioxide build up is necessary for long-term missions. Currently, the prevailing liquid sorbent used in submarines and industrial flue gas utilizes the primary amine, monoethanolamine (MEA), to capture, transfer, and remove carbon dioxide from air. Diglycolamine (DGA) is an alternate primary amine that has similar performance and less volatility. It is currently being studied at Ames Research Center (ARC) and is the primary candidate for the operation of the sub-scale liquid amine test stand. The test stand is used to investigate liquid flow and liquid gas interfaces to assist in a system design for microgravity applications. The test stand includes a wedge design utilizes capillary action to hold the liquid while allowing gas-liquid interaction for carbon dioxide transfer. These wedge trays are placed in a contactor unit to remove carbon dioxide from the air stream, a degasser unit to replenish the liquid amine, and a capillary condensing heat exchanger (CCHX) to recapture water lost in the degasser unit. Nominal operating conditions for the contactor are a gas flow rate of 26scfm enriched with pure CO2 to 2600ppm and a liquid mixture of 65/35 vol% DGA/H2O at 0.65mL/min while the degasser was operated at 100°C and 1 atm. This paper discusses the challenges and limitations of a fully integrated system which will influence the design of a new subscale test stand.

Adrian Cortez↗

NASA NTRS2024

Assessment of Secondary Pitot Probe Locations on a Small UAS

Urban Air Mobility (UAM) and Advanced Air Mobility (AAM) have been at the forefront of many aeronautical discussions because of the potential revolutionary improvement to urban transportation. In this study, a representative Research Aircraft for eVTOL Enabling techNologies, Sub-scale Wind Tunnel Flight Test (RAVEN SWFT) nosecone was placed inside the NASA Langley Research Center’s 12-Foot Low-Speed Wind Tunnel with a pitot-static assembly installed. The study aimed to determine a suitable location and orientation of the pitot-static assembly on the nose of the vehicle, which consists of two airspeed sensors: one for the flight controller and one for data collection. The dynamic pressure was varied from 0.5 to 5psf for each test point. Additionally, three different offset distances from the center boom and three different angles for the flight controller pitot tube were tested. The data from both of the pitot tube assemblies were compared to the wind tunnel and the Aeroprobe pitot tube. The results show the flight controller pitot tube performs better when it is placed further away from the nosecone, regardless of the angle. The results also show that the angle does not affect the accuracy of the pitot tube when the vehicle yaws or pitches regardless of the mounting angle and location. The study provides useful insights for the design of the airspeed measurement systems on small Uncrewed Aerial Systems (sUAS), which can be applied to other UAM and AAM applications.

AAM↗

NASA NTRSDate not supplied

Comprehensive Evaluation of Electrochemical Hydrogen Separator as Hydrogen Recovery Solution for Plasma Pyrolysis Assembly

The previously tested State-of-the-Art (SOA) air revitalization architecture onboard the International Space Station recovers approximately 50% of the oxygen (O 2 ) from metabolic carbon dioxide (CO 2 ) via the Sabatier process. Maximum O 2 recovery is required to reduce resupply mass for long-duration manned missions. O 2 recovery is constrained by the limited availability of reactant hydrogen (H 2 ) from water (H 2 O) electrolysis, and Sabatier-produced methane (CH 4 ) is vented as a waste product resulting in a continuous loss of reactant H 2 . The Plasma Pyrolysis Assembly (PPA) has the potential to substantially increase O 2 recovery by post-processing the Sabatier-produced methane to recover H 2 . The PPA decomposes CH 4 into predominately H 2 and acetylene (C 2 H 2 ). A separation system is needed to purify the H 2 from the PPA stream before it is recycled back to the Sabatier reactor. Two sub-scale electrochemical H 2 separation systems, developed by Skyre, Incorporated, were delivered to NASA for evaluation. Complimentary of the previous submittal, ICES-2023-260, this paper reports a summation of Phase I and Phase II testing and evaluation of the C 2 H 2 removal systems as well as lessons learned.

Plasma Pyrolysis Assembly↗

NASA NTRSDate not supplied

Testing of Two Mars Powered Descent Vehicle Concepts in the Langley Unitary Plan Wind Tunnel

Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). Each model was designed to accommodate up to eight nozzles, with the HIAD model having five different nozzle configurations to investigate the effects of nozzle location, cant angle, and area ratio. The models were tested with high pressure air as the nozzle plume gas, and included the following instrumentation: high-speed video, discrete steady state and high-frequency pressure, pressure sensitive paint, and a new flow-through force and moment balance for the HIAD model. The high-speed imagery showed the overall expected growth of the shock layer to increasing thrust levels. The discrete stagnation pressure data on the HIAD model with four and eight blowing nozzles was sensitive to thrust coefficient with the nozzles canted at 0 degrees, whereas having nozzles canted outward 20 degrees and/or being located closer to the heatshield shoulder largely removed that sensitivity. The CobraMRV model stagnation pressure was more sensitive to tunnel Mach number and sideslip angle, due to the nozzle arrangement and plume interference. Pressure sensitive paint data quality was compromised by paint damage from frequent model changes, especially for the HIAD model. However, pressure coefficient data on the CobraMRV model showed the same trends as the discrete pressure measurements, as well as a sensitivity to non-zero sideslip angles. The aerodynamic force coefficients were derived from the pressure sensitive paint data. On the HIAD models, the primary force coefficient decreased with increasing thrust due to the nozzle plumes blocking flow to the heatshield area surrounding the nozzle exist. On the CobraMRV model, the force coefficient was relatively insensitive to thrust coefficient at the lower Mach number when sideslip angle was 0 degrees The force coefficient decreases with increasing thrust coefficient when the sideslip angle is 10 degrees. Balance data quality was negatively impacted by thermal drift issues that were not apparent in pre-test calibration measurements, thus preventing usable test data. Results and lessons learned will be used to take further technology development steps, including more advanced ground test techniques and flight testing.

Karl T Edquist↗

NASA NTRSDate not supplied

SUbsonic Single Aft eNgine (SUSAN) Power/Propulsion System Hardware-in-the-Loop Test Results

Electrified Aircraft Propulsion (EAP) technology offers a promising path forward for reducing greenhouse gas emissions and other negative environmental effects from the commercial aviation sector. EAP systems can reduce fuel burn and improve performance over state-of the-art designs, however the increased complexity and highly coupled nature of these systems present challenges that require new control approaches. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a concept aircraft developed by NASA as a reference design for a commercial transport aircraft with a highly integrated hybrid-electric powertrain. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test of a control architecture developed for the SUSAN power/propulsion system (PPS). The test was performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at the NASA Glenn Research Center (GRC) and involved a real-time reference model of the SUSAN PPS and control system running with a sub-scale electro-mechanical system replacing one of the PPS subsystems. A side-by-side comparison of the simulated and real systems in the HIL test results shows that the control architecture functions well in both the simulation and the real-time HIL environment. In both cases the controller is able to simultaneously deliver the required thrust response and balance power levels between the electrical and turbomachinery subsystems.

Jonah J Sachs-Wetstone↗

NASA NTRSDate not supplied

SUbsonic Single Aft eNgine (SUSAN) Power/Propulsion System Hardware-in-the-Loop Test Results

Electrified Aircraft Propulsion (EAP) technology offers a promising path forward for reducing greenhouse gas emissions and other negative environmental effects from the commercial aviation sector. EAP systems can reduce fuel burn and improve performance over state-of the-art designs, however the increased complexity and highly coupled nature of these systems present challenges that require new control approaches. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a concept aircraft developed by NASA as a reference design for a commercial transport aircraft with a highly integrated hybrid-electric powertrain. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test of a control architecture developed for the SUSAN power/propulsion system (PPS). The test was performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at the NASA Glenn Research Center (GRC) and involved a real-time reference model of the SUSAN PPS and control system running with a sub-scale electro-mechanical system replacing one of the PPS subsystems. A side-by-side comparison of the simulated and real systems in the HIL test results shows that the control architecture functions well in both the simulation and the real-time HIL environment. In both cases the controller is able to simultaneously deliver the required thrust response and balance power levels between the electrical and turbomachinery subsystems.

EAP↗

NASA NTRSDate not supplied

Testing of Two Mars Powered Descent Vehicle Concepts in the Langley Unitary Plan Wind Tunnel

Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). Each model was designed to accommodate up to eight nozzles, with the HIAD model having five different nozzle configurations to investigate the effects of nozzle location, cant angle, and area ratio. The models were tested with high pressure air as the nozzle plume gas, and included the following instrumentation: high-speed video, discrete steady state and high-frequency pressure, pressure sensitive paint, and a new flow-through force and moment balance for the HIAD model. The high-speed imagery showed the overall expected growth of the shock layer to increasing thrust levels. The discrete stagnation pressure data on the HIAD model with four and eight blowing nozzles was sensitive to thrust coefficient with the nozzles canted at 0 degrees, whereas having nozzles canted outward 20 degrees and/or being located closer to the heatshield shoulder largely removed that sensitivity. The CobraMRV model stagnation pressure was more sensitive to tunnel Mach number and sideslip angle, due to the nozzle arrangement and plume interference. Pressure sensitive paint data quality was compromised by paint damage from frequent model changes, especially for the HIAD model. However, pressure coefficient data on the CobraMRV model showed the same trends as the discrete pressure measurements, as well as a sensitivity to non-zero sideslip angles. The aerodynamic force coefficients were derived from the pressure sensitive paint data. On the HIAD models, the primary force coefficient decreased with increasing thrust due to the nozzle plumes blocking flow to the heatshield area surrounding the nozzle exist. On the CobraMRV model, the force coefficient was relatively insensitive to thrust coefficient at the lower Mach number when sideslip angle was 0 degrees The force coefficient decreases with increasing thrust coefficient when the sideslip angle is 10 degrees. Balance data quality was negatively impacted by thermal drift issues that were not apparent in pre-test calibration measurements, thus preventing usable test data. Results and lessons learned will be used to take further technology development steps, including more advanced ground test techniques and flight testing.

Supersonic Retropropulsion↗

NASA NTRS2025

Inflatable Softgoods Design of an Articulating Crew Transfer Tunnel

Future NASA exploration plans call for lunar and Martian surface systems that form a base camp of multiple, pressurized elements. These discrete components, including habitats and pressurized rovers, require interoperability to meet the Artemis Accords and standard docking systems to physically connect elements together. A pressurized, articulating crew transfer tunnel can be used between a rover and habitat to enable shirt-sleeve transfer of crew and cargo, saving valuable crew time and resources. While transfer tunnels have been described in the past, this work details the design of a structural softgoods system that has compliant capability through a proposed docking range of motion. The inflatable softgoods design is based on a zero-hoop stress shape, known as a Taylor surface, that is stacked and truncated to form a unique and flexible configuration. Analytical, non-linear models have been developed to examine and predict the behavior of the structure, and material testing was used to determine the properties that were used in the model. Finally, a sub-scale test article was constructed using the baseline design and pressurized testing is in work. Additional full-scale testing is planned for future years to fully demonstrate the capability of the system.

Tunnel↗

NASA NTRSDate not supplied

Inflatable Softgoods Design of an Articulating Crew Transfer Tunnel

Future NASA exploration plans call for lunar and Martian surface systems that form a base camp of multiple, pressurized elements. These discrete components, including habitats and pressurized rovers, require interoperability to meet the Artemis Accords and standard docking systems to physically connect elements together. A pressurized, articulating crew transfer tunnel can be used between a rover and habitat to enable shirt-sleeve transfer of crew and cargo, saving valuable crew time and resources. While transfer tunnels have been described in the past, this work details the design of a structural softgoods system that has compliant capability through a proposed docking range of motion. The inflatable softgoods design is based on a zero-hoop stress shape, known as a Taylor surface, that is stacked and truncated to form a unique and flexible configuration. Analytical, non-linear models have been developed to examine and predict the behavior of the structure, and material testing was used to determine the properties that were used in the model. Finally, a sub-scale test article was constructed using the baseline design and pressurized testing is in work. Additional full-scale testing is planned for future years to fully demonstrate the capability of the system.

Tunnel↗

NASA NTRS2025

A Summary of Results from Vertical Drop Testing of Hybrid III and WIAMan ATDs

With the development and maturation of the Urban Air Mobility (UAM) market, many new types of electric vertical take-off and landing (eVTOL) vehicles will be flying in the national airspace carrying goods, people or conducting operations for a variety of missions. These types of vehicles are unlike current aircraft due to their novel design and operational profile. Several considerations must be examined in areas including noise, comfort and safety in order for these vehicles to be utilized and accepted into the current airspace system. Researchers at NASA Langley Research Center (LaRC) have conducted sub-scale and full-scale tests on representative eVTOL airframes and seats under a variety of dynamic impact conditions. These tests were conducted to generate data necessary to inform the development of standards in the areas specific to crashworthiness of eVTOL vehicle systems and safety. The data in this report relates to occupant responses obtained during a test campaign utilizing various makes, models, and sizes of Anthropomorphic Test Devices (ATD’s, a.k.a. crash test dummies) undergoing vertical impacts in a variety of seats. The data is intended to provide occupant behavior response and injury metrics for several anticipated impact scenarios that may occur in eVTOL operations. This report will present test data highlighting the effects of several variables on the test results. Discussions on the ATD sizes, along with comparisons between different ATD makes and types will be included. The performance of an in-house developed energy absorbing seat will be detailed, and discussions pertaining to the applicability in various loading conditions will be presented. Finally, a discussion as to the applicability of the tested results to eVTOL full-scale conditions will be included.

Dynamic Drop Testing↗