Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stress state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Coupled 2D-3D finite element method for analysis of a skin panel with a discontinuous stiffener

This paper describes a computationally efficient analysis method which was used to predict detailed stress states in a typical composite compression panel with a discontinuous hat stiffener. A global-local approach was used. The global model incorporated both 2D shell and 3D brick elements connected by newly developed transition elements. Most of the panel was modeled with 2D elements, while 3D elements were employed to model the stiffener flange and the adjacent skin. Both linear and geometrically nonlinear analyses were performed on the global model. The effect of geometric nonlinearity induced by the eccentric load path due to the discontinuous hat stiffener was significant. The local model used a fine mesh of 3D brick elements to model the region at the end of the stiffener. Boundary conditions of the local 3D model were obtained by spline interpolation of the nodal displacements from the global analysis. Detailed in-plane and through-the-thickness stresses were calculated in the flange-skin interface near the end of the stiffener.

Wang, J. T.↗
NASA NTRS2000

Crustal Deformation Associated with Glacial Fluctuations in the Eastern Chugach Mountains, Alaska

The changes of the solid Earth in south central Alaska in response to two major glacial fluctuations on different temporal and spatial scales have been estimated and we evaluated their influence on the stress state and ongoing tectonic deformation of the region. During the recent (1993-1995) Bering Glacier surge, a large transfer of ice from the Bagley Ice Field to the Bering Glacier terminus region occurred. We estimated the elastic displacement of the solid Earth due to ice mass redistribution from Global Positioning System (GPS) measurements at sites near the surging glacier. We can account for these displacements by transfer of an ice volume of about 14 cubic km from the surge reservoir area to the terminus region. We examined the background seismicity (M(sub L) > 2.5) before, during, and after the surge. We found that the occurrence of small earthquakes (M(sub L) < 4.0) in the surge reservoir region increased during the surge time interval possibly in response to a decrease in ice mass. This suggests that a small decrease in the vertical stress, o,3, could be enough to modulate the occurrence of small, shallow earthquakes in this dominantly thrust fault setting. During this century the southern Alaska coastal glaciers have been undergoing an overall decrease in volume. Based on our compilation of changes in the extent and thickness of the coastal glaciers between the Malaspina and Bering, we calculated surface displacements due to the Earth's viscoelastic response to annual thinning and to the cumulative retreat over the last 100 years. The uplift of the region due to an average annual thinning rate of 1-6 m/yr in the ablation region is 1-12 mm/yr. For our reference model with a viscosity of 5 x 10(exp 19) Pa s for depths between approximately equal 40 and 200 km the total viscoelastic response due to the retreat over the last century may be as much as a couple of meters within the coastal ablation zone near Icy Bay. The maximum decrease in sigma(sub V) between 0 and 10 km was approximately equal 1.0 MPa, which is significant in relation to the stress drops in recent earthquakes (approximately 2 to 10 MPa) but small in relation to the estimated tectonic stress magnitude. Therefore the occurrence of an earthquake such as the St. Elias (1979, M(sub S) = 7.2) may have been advanced in time; however, most of the ongoing stress accumulation would be primarily due to tectonic forces.

Sauber, Jeanne↗
NASA NTRS2007

A Comparison of Two Skip Entry Guidance Algorithms

The Orion capsule vehicle will have a Lift-to-Drag ratio (L/D) of 0.3-0.35. For an Apollo-like direct entry into the Earth's atmosphere from a lunar return trajectory, this L/D will give the vehicle a maximum range of about 2500 nm and a maximum crossrange of 216 nm. In order to y longer ranges, the vehicle lift must be used to loft the trajectory such that the aerodynamic forces are decreased. A Skip-Trajectory results if the vehicle leaves the sensible atmosphere and a second entry occurs downrange of the atmospheric exit point. The Orion capsule is required to have landing site access (either on land or in water) inside the Continental United States (CONUS) for lunar returns anytime during the lunar month. This requirement means the vehicle must be capable of flying ranges of at least 5500 nm. For the L/D of the vehicle, this is only possible with the use of a guided Skip-Trajectory. A skip entry guidance algorithm is necessary to achieve this requirement. Two skip entry guidance algorithms have been developed: the Numerical Skip Entry Guidance (NSEG) algorithm was developed at NASA/JSC and PredGuid was developed at Draper Laboratory. A comparison of these two algorithms will be presented in this paper. Each algorithm has been implemented in a high-fidelity, 6 degree-of-freedom simulation called the Advanced NASA Technology Architecture for Exploration Studies (ANTARES). NASA and Draper engineers have completed several monte carlo analyses in order to compare the performance of each algorithm in various stress states. Each algorithm has been tested for entry-to-target ranges to include direct entries and skip entries of varying length. Dispersions have been included on the initial entry interface state, vehicle mass properties, vehicle aerodynamics, atmosphere, and Reaction Control System (RCS). Performance criteria include miss distance to the target, RCS fuel usage, maximum g-loads and heat rates for the first and second entry, total heat load, and control system saturation. The comparison of the performance criteria has led to a down select and guidance merger that will take the best ideas from each algorithm to create one skip entry guidance algorithm for the Orion vehicle.

Rea, Jeremy R.↗
DOE OSTI2021

Compaction of crushed salt for safe containment – overview of the KOMPASS project

Abstract. In Germany, rock salt formations are possible host rock candidates for a repository for heat-emitting radioactive waste. The safety concept of a repository in salt bases on a multibarrier system consisting mainly of the geological barrier salt and geotechnical seals ensuring safe containment. Crushed salt will be used for backfilling of cavities and sealing measures in drifts and shafts due to its favourable properties and its easy availability (mined-off material). The creep of the rock salt leads to crushed salt compaction with time. Thereby, the crushed salts' porosity is reduced from the initial porosity of 30 %–40 % to a value comparable to the porosity of undisturbed rock salt (≤1 %). In such low porosity ranges, technical impermeability is assumed. The compaction behaviour of crushed salt is rather complex and involves several coupled THM processes (Kröhn et al., 2017; Hansen et al., 2014). It is influenced by internal properties like humidity and grain size distribution, as well as boundary conditions such as temperature, compaction rate or stress state. However, the current process understanding has some important gaps referring to the material behaviour, experimental database and numerical modelling. It needs to be extended and validated, especially in the low porosity range. The objective of the KOMPASS project was development of methods and strategies for the reduction of deficits in the prediction of crushed salt compaction leading to an improvement of the prognosis quality. Key results are as follows (KOMPASS Phase 1, 2020): selection of an easily available and permanently producible synthetic crushed salt mixture, acting as a reference material for generic investigations; development and proof of different techniques for producing pre-compacted samples for further investigations; establishment of a tool of microstructure investigation methods to demonstrate the comparability of grain structures of pre-compacted samples with in-situ compacted material for future investigations; execution of various laboratory experiments using pre-compacted samples, e.g. long-term creep tests which deliver reliable information about time- and stress-dependent compaction behaviour; development of a complex experimental investigation strategy to derive necessary model parameters considering individual functional dependencies. Its technical feasibility was successfully verified; benchmarking with various existing numerical models using datasets from three different triaxial long-term tests. The result was not entirely satisfactory; however, the number of influencing factors is small and further validation work has to be done. Overall, the KOMPASS project has made significant progress in the approaches to solving the outstanding question, building the basis for further investigations.

Friedenberg, Larissa↗
DOE OSTI2022

Temperature-Dependent Thermal and Mechanical Properties of a Wire Arc Additively Manufactured Low Transformation Temperature Steel

Recent research has studied the use of low transformation temperature (LTT) martensite steel as feedstock for wire arc additive manufacturing (WAAM) and low tensile residual stresses or compressive residual stresses were detected in the printed walls. These residual stress states help to improve printed product properties such as fatigue strength and corrosion resistance. However, the thermal and mechanical properties of WAAM printed LTT martensite steel walls are largely unknown. In this work, a printed LTT martensite steel was characterized for its thermal, metallurgical, and mechanical behavior at room and elevated temperatures. The temperature-dependent specific heat capacity, thermal expansion, atomic lattice spacing, and tensile properties were measured during both heating and cooling and related to observed microstructural features and computational thermodynamics predictions. These results revealed a large hysteresis in the martensitic transformation, with a martensite start temperature of 240 °C and austenite start temperature of 680 °C. Additional thermal cycles and specimen orientation did not affect the printed specimen austenite and martensite transformations. However, it was observed that the printed metal may exhibit tempering embrittlement at about 350 °C but further studies are needed to confirm that. Further, these results suggest that a temperature control of 250 °C to 350 °C during WAAM is needed to maximize the stress reduction potential of the LTT250 martensite steel. Opportunities for future implementation of LTT martensite steels and optimization of additive manufacturing process conditions are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Cold Spray Deposition of 304L Stainless Steel to Mitigate Chloride-Induced Stress Corrosion Cracking in Canisters for Used Nuclear Fuel Storage

A feasibility study of the cold spray deposition process of 304L stainless steel on 304L stainless steel substrates as a mitigation method for chloride-induced stress corrosion cracking (CISCC) has been investigated under various substrate conditions. The study is aimed at the application of this technology to mitigate CISCC that may potentially occur in or nearthe fusion welded regions of stainless steel canisters in Dry Cask Storage System (DCSS) for used nuclear fuels. Spherical gas-atomized 304L stainless steel powder, in the size range of 25 µm to 44 µm, was used as a feedstock powder for the cold spray process. The powder was deposited on four types of 304L substrates with various surface conditions: as-polished, oxidized, cold-rolled, plates with prototypical CISCC. The effects of cold spray parameters on quality of cold spray coatings were investigated. Thickness, porosity, and phases in the as-deposited materials were evaluated using scanning electron microscopy (SEM) and X-ray diffraction (XRD), and correlated with microhardness and adhesion strength measured via micro-indentation and ASTM C633 pulling test, respectively. XRD analysis of the coatings was also conducted to examine the effects of cold spray condition on residual stress state in the coating. Detailed cross-sectional examination of coating/substrate interfaces was performed with transmission electron microscopy (TEM) equipped with energy dispersive spectroscopy (EDS). Dense and continuous coatings with good adhesion strength and hardness were produced for the various substrate conditions by adjusting cold spray parameters. The results demonstrate that cold spray stainless steel coating is a viable option to provide a physical barrier against CISCC in fusion weld regions of stainless steel in corrosive chloride salt-bearing environments.

Dry Cask Storage Systems, cold spray, 304L stainle↗
DOE OSTI2021

New insights into creep characteristics of calcium silicate hydrates at molecular level

The fundamental mechanisms under concrete creep are far from being fully understood, especially at the molecular level. Hereby, a calcium-silicate-hydrate (C-S-H) molecular model is developed to explain, for the first time, the creep characteristics at various stress states, temperature levels and water contents, which are not accessible experimentally. Rather tensile and compressive loadings, C-S-H only creeps under shear loadings originating from the sliding of the calcium silicate layers over each other as the interlayer component (water and ions) acts as a lubricator. A heterogeneous creep characteristic is observed. Elevated temperature reduces the interlayer lubricator viscosity and weakens the interfacial adhesion between the layers and the interlayer lubricator, which accelerates C-S-H creep. The removal of interlayer water enhances the creep resistance, resulting from the reduced interlayer space and enhanced interfacial adhesion. The atomic-level mechanisms explain the inter-CSH-particle behaviours at the microscale, which bridges the gap between atomistic simulation and microcosmic phenomenon.

36 MATERIALS SCIENCE↗
NASA NTRS2016

Analysis and Characterization of Damage and Failure Utilizing a Generalized Composite Material Model Suitable for Use in Impact Problems

A material model which incorporates several key capabilities which have been identified by the aerospace community as lacking in state-of-the art composite impact models is under development. In particular, a next generation composite impact material model, jointly developed by the FAA and NASA, is being implemented into the commercial transient dynamic finite element code LS-DYNA. The material model, which incorporates plasticity, damage, and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters (such as modulus and strength). The plasticity portion of the orthotropic, three-dimensional, macroscopic composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function with a non-associative flow rule. For the damage model, a strain equivalent formulation is utilized to allow for the uncoupling of the deformation and damage analyses. In the damage model, a semi-coupled approach is employed where the overall damage in a particular coordinate direction is assumed to be a multiplicative combination of the damage in that direction resulting from the applied loads in the various coordinate directions. Due to the fact that the plasticity and damage models are uncoupled, test procedures and methods to both characterize the damage model and to covert the material stress-strain curves from the true (damaged) stress space to the effective (undamaged) stress space have been developed. A methodology has been developed to input the experimentally determined composite failure surface in a tabulated manner. An analytical approach is then utilized to track how close the current stress state is to the failure surface.

Finite Element Method↗
DOE OSTI2021

Impact of downhole pressure and fluid-access on the effectiveness of wellbore cement expansion additives

Autogenous shrinkage of wellbore cement widely impairs zonal isolation. MgO-based cement expansion additives (CEAs) can mitigate this shrinkage, or even impart net expansion, by creating porosity through displacive crystal growth-processes. However, both MgO hydration and autogenous shrinkage behaviour depend strongly on stress state. Evaluation of CEA performance in wellbore cements therefore requires testing under elevated pressures representative for subsurface environments. We report experiments addressing the chemical and bulk volume changes that occur in cement hydrating at 10 MPa confining pressure and 90 °C. Volumetric response was investigated as function of MgO concentration, external water supply, and pore pressure decrease through water consumption during reaction. Results show the bulk expansion achieved using MgO-based CEAs diminishes markedly with increasing effective confining pressure or, equivalently, upon restricting fluid supply. This reduced expansion-potential under pressure has profound implications for slurry design, notably regarding CEA-concentrations required to counteract micro-annulus formation while maintaining low cement permeability.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Assessment of impact damage of composite rocket motor cases

This contract reviewed the available literature on mechanisms of low velocity impact damage in filament wound rocket motor cases, MDE methods to quantify damage, critical coupon level test methods, manufacturing and material process variables and empirical and analytical modeling off impact damage. The critical design properties for rocket motor cases are biaxial hoop and axial tensile strength. Low velocity impact damage is insidious because it can create serious nonvisible damage at very low impact velocities. In thick rocket motor cases the prevalent low velocity impact damage is fiber fracture and matrix cracking adjacent to the front face. In contrast, low velocity loading of thin wall cylinders induces flexure, depending on span length and the flexure induces delamination and tensile cracking on the back face wall opposed to impact occurs due to flexural stresses imposed by impact loading. Important NDE methods for rocket motor cases are non-contacting methods that allow inspection from one side. Among these are vibrothermography, and pulse-echo methods based on acoustic-ultrasonic methods. High resolution techniques such as x-ray computed tomography appear to have merit for accurate geometrical characterization of local damage to support development of analytical models of micromechanics. The challenge of coupon level testing is to reproduce the biaxial stress state that the full scale article experiences, and to determine how to scale the composite structure to model full sized behavior. Biaxial tensile testing has been performed by uniaxially tensile loading internally pressurized cylinders. This is experimentally difficult due to gripping problems and pressure containment. Much prior work focused on uniaxial tensile testing of model filament wound cylinders. Interpretation of the results of some studies is complicated by the fact that the fabrication process did not duplicate full scale manufacturing. It is difficult to scale results from testing subscale cylinders since there are significant differences in out time of the resins relative to full scale cylinder fabrication, differences in hoop fiber tensioning and unsatisfactory coupon configurations. It appears that development of a new test method for subscale cylinders is merited. Damage tolerance may be improved by material optimization that uses fiber treatments and matrix modifications to control the fiber matrix interface bonding. It is difficult to develop process optimization in subscale cylinders without also modeling the longer out times resins experience in full scale testing. A major breakthrough in characterizing the effect of impact damage on residual strength, and understanding how to scale results of subscale evaluations, will be a sound micromechanical model that described progressive failure of the composite. Such models will utilize a three dimensional stress analysis due to the complex nature of low velocity impact stresses in thick composites. When these models are coupled with non-contact NDE methods that geometrically characterize the damage and acoustic methods that characterize the effective local elastic properties, accurate assessment of residual strength from impact damage may be possible. Directions for further development are suggested.

Paris, Henry G.↗
DOE OSTI2024

DECOVALEX-2023: Task A Final Report

Task A, also known as HGFrac, examines the fracturing processes that may occur in the Callovo-Oxfordian claystone (COx) in the context of the high-level (HLW) and intermediate-level long-lived (ILW-LL) radioactive waste repository in France. Understanding these processes and improving numerical models to reproduce them will aid in the design, optimization, and safety of the repository. Heat and gas fracturing are studied in two independent subtasks following a stepwise approach: laboratory tests/benchmark exercises, in-situ experiment, and finally, an application case. The in-situ heater experiment aimed to thermally induce a hydraulic fracture; temperature and pore pressure were monitored to detect any evidence of fracturing. The in-situ gas injection experiment aimed to study the effect of the stress orientation and gas injection kinetics on the gas fracturing process. The occurrence of fracturing was monitored by gas pressure measured in the injection interval. In both experiments, the excavation-induced fracture network around the heater/injection boreholes played an important role in the reduction of the compressive stress state, leading to both a tensile and shear failure response of the COx. During the first two years of the project, the research teams working on each task developed and/or proposed numerical approaches for reproducing the occurrence of fracturing in the in-situ experiments. The failure criteria were defined by reproducing the measurements from laboratory extension tests for the heat fracturing subtask. In the gas fracturing subtask, their approaches were used for simulating several benchmark exercises, and an inter-comparison between models was carried out. In both tasks, the developed approaches were compared with a simplified approach considering poro-elasticity for the mechanical behaviour of the COx. Most of the developed approaches are based on a continuous medium that takes into account variations in hydraulic properties due to mechanical degradation, such as plastic deformation or damage. Other approaches implicitly modelled weak planes or embedded discontinuities to reproduce fracture propagation. The potential for fracture initiation was also studied through of a discrete approach. In the second half of the project, the research teams mainly focused on interpretative modelling of two in-situ experiments and a blind prediction exercise to test their respective approaches. The models developed by the research teams were also applied at the repository scale to evaluate fracture initiation in a case study under vi unfavourable conditions, particularly in terms of spacing between High-Level Waste cells. The results showed that the poro-elasticity approach could be an efficient tool for understanding the main processes occurring in the COx. One example is the explicit representation of the excavation-induced fracture network around the boreholes, which yielded acceptable results compared to the measurement data. However, advanced approaches were needed to evaluate the potential increase of the excavation-induced fracture network extend and better understand fracture initiation. The stress analyses carried out by the teams revealed that hydraulic boundary conditions had a strong impact on fracture initiation in the heater experiment. Furthermore, in most cases, the results required higher pore pressure increments to reach fracturing than those measured in the experiment. This implies that the measurements may have been biased by the packer’s capacity to fully isolate the piezometric chambers, leading to lower pressures. On the contrary, there was no agreement on the fracturing mode, as some reported either shear or tensile fracturing, while others reported a combination of the two modes. In the case of gas fracturing, the research teams were limited to the comparison of a single point, which complicated their task. Nonetheless, the numerical results were able to reproduce the measurements and capture processes such as longitudinal gas flow through the excavation-induced fracture network, as suggested by some evidence in the observation piezometric chambers. The numerical models also agreed with the measurements in the sense of higher probability of developing along the injection borehole than radially towards the sound rock. The approaches developed by the research teams showed that they are capable of analysing and reproducing fracture initiation in the COx. However, areas of future work should focus on the fracture propagation and fracture aperture, which were out of the scope of this task. To this end, additional data must be gathered for the parameter characterisation and validation of the numerical models. Nonetheless, various approaches showed promising results as they were able to reproduce fracture development under certain conditions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2010

Experimental Creep Life Assessment for the Advanced Stirling Convertor Heater Head

The United States Department of Energy is planning to develop the Advanced Stirling Radioisotope Generator (ASRG) for the National Aeronautics and Space Administration (NASA) for potential use on future space missions. The ASRG provides substantial efficiency and specific power improvements over radioisotope power systems of heritage designs. The ASRG would use General Purpose Heat Source modules as energy sources and the free-piston Advanced Stirling Convertor (ASC) to convert heat into electrical energy. Lockheed Martin Corporation of Valley Forge, Pennsylvania, is integrating the ASRG systems, and Sunpower, Inc., of Athens, Ohio, is designing and building the ASC. NASA Glenn Research Center of Cleveland, Ohio, manages the Sunpower contract and provides technology development in several areas for the ASC. One area is reliability assessment for the ASC heater head, a critical pressure vessel within which heat is converted into mechanical oscillation of a displacer piston. For high system efficiency, the ASC heater head operates at very high temperature (850 C) and therefore is fabricated from an advanced heat-resistant nickel-based superalloy Microcast MarM-247. Since use of MarM-247 in a thin-walled pressure vessel is atypical, much effort is required to assure that the system will operate reliably for its design life of 17 years. One life-limiting structural response for this application is creep; creep deformation is the accumulation of time-dependent inelastic strain under sustained loading over time. If allowed to progress, the deformation eventually results in creep rupture. Since creep material properties are not available in the open literature, a detailed creep life assessment of the ASC heater head effort is underway. This paper presents an overview of that creep life assessment approach, including the reliability-based creep criteria developed from coupon testing, and the associated heater head deterministic and probabilistic analyses. The approach also includes direct benchmark experimental creep assessment. This element provides high-fidelity creep testing of prototypical heater head test articles to investigate the relevant material issues and multiaxial stress state. Benchmark testing provides required data to evaluate the complex life assessment methodology and to validate that analysis. Results from current benchmark heater head tests and newly developed experimental methods are presented. In the concluding remarks, the test results are shown to compare favorably with the creep strain predictions and are the first experimental evidence for a robust ASC heater head creep life.

Krause, David L.↗
DOE OSTI2023

Influence of Potassium Metal‐Support Interactions on Dendrite Growth

Abstract Combined synchrotron X‐ray nanotomography imaging, cryogenic electron microscopy (cryo‐EM) and modeling elucidate how potassium (K) metal‐support energetics influence electrodeposit microstructure. Three model supports are employed: O‐functionalized carbon cloth (potassiophilic, fully‐wetted), non‐functionalized cloth and Cu foil (potassiophobic, nonwetted). Nanotomography and focused ion beam (cryo‐FIB) cross‐sections yield complementary three‐dimensional (3D) maps of cycled electrodeposits. Electrodeposit on potassiophobic support is a triphasic sponge, with fibrous dendrites covered by solid electrolyte interphase (SEI) and interspersed with nanopores (sub‐10 nm to 100 nm scale). Lage cracks and voids are also a key feature. On potassiophilic support, the deposit is dense and pore‐free, with uniform surface and SEI morphology. Mesoscale modeling captures the critical role of substrate‐metal interaction on K metal film nucleation and growth, as well as the associated stress state.

Liu, Pengcheng↗
DOE OSTI2023

Influence of Potassium Metal-Support Interactions on Dendrite Growth

We report combined synchrotron X-ray nanotomography imaging, cryogenic electron microscopy (cryo-EM) and modeling elucidate how potassium (K) metal-support energetics influence electrodeposit microstructure. Three model supports are employed: O-functionalized carbon cloth (potassiophilic, fully-wetted), non-functionalized cloth and Cu foil (potassiophobic, nonwetted). Nanotomography and focused ion beam (cryo-FIB) cross-sections yield complementary three-dimensional (3D) maps of cycled electrodeposits. Electrodeposit on potassiophobic support is a triphasic sponge, with fibrous dendrites covered by solid electrolyte interphase (SEI) and interspersed with nanopores (sub-10 nm to 100 nm scale). Lage cracks and voids are also a key feature. On potassiophilic support, the deposit is dense and pore-free, with uniform surface and SEI morphology. Mesoscale modeling captures the critical role of substrate-metal interaction on K metal film nucleation and growth, as well as the associated stress state.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Micropolar Elastoplasticity Using a Fast Fourier Transform‐Based Solver

ABSTRACT This work presents a micromechanical spectral formulation for obtaining the full‐field and homogenized response of elastoplastic micropolar composites. A closed‐form radial‐return mapping is derived from thermodynamics‐based micropolar elastoplastic constitutive equations to determine the increment of plastic strain necessary to return the generalized stress state to the yield surface, and the algorithm implementation is verified using the method of numerically manufactured solutions. Then, size‐dependent material response and micro‐plasticity are shown as features that may be efficiently simulated in this micropolar elastoplastic framework. The computational efficiency of the formulation enables the generation of large datasets in reasonable computing times.

42 ENGINEERING↗
DOE OSTI2020

Linear viscoelastic characterization of electrically conductive adhesives used as interconnect in photovoltaic modules

Electrically conductive adhesives (ECAs) are incorporated into recent designs of photovoltaic (PV) modules and replace the traditional metallic solders as interconnects. This transition depicts a significant material change, and a proper understanding of the interconnects' mechanical response has not yet been established. However, such an understanding is necessary to (a) identify the driving forces for module degradation and failure, (b) allow for module design optimization, and (c) enable accurate lifetime predictions. This study summarizes the framework for the mechanical materials characterization and modeling of ECAs for PV applications. Only high-fidelity material models are able to capture the rate and temperature dependency of the ECA interconnect and allow for accurate modeling of the materials response. Furthermore, a linear viscoelastic representation is found to describe the mechanical response of the ECAs sufficiently well. The effects of curing conditions and environmental exposure are investigated, and material models for a variety of ECAs are reported and prepared for the use in numerical simulations. Overall, a finite element simulation of a generic submodel of a shingled cell module is used to highlight the need for high-fidelity material models and demonstrates the error made in the predicted stress states by using less sophisticated models.

14 SOLAR ENERGY↗
DOE OSTI2022

A Novel Rotating Flexure-Test Technique for Brittle Materials with Circular Geometries

The four-point bend test is one of the simplest and often the preferred flexural strength evaluation method for brittle materials. In this loading mode, fracture often initiates from a critical surface (or subsurface) flaw when subjected to a tensile stress state. However, if the critical flaw exists on the compression side of the test specimen, it may not activate to grow a crack and hence the resulting flexural strength will be higher than the true value. The goal of this study is to measure the true flexural strength of a solid or hollow cylindrical brittle specimen by ensuring that failure occurs at its weakest point by rotating along its longitudinal axis, thereby exposing and activating its critical surface flaw during a four-point bend test. A novel test fixture has been designed and fabricated, and the true flexural strengths of cylindrical brittle and quasi-brittle tubular specimens have been measured and compared to existing experimental data obtained through traditional four-point bend tests. In this work, experimental results showcase the orientation dependance on flexural strength for various materials. Additionally, similarities between experimental findings and those available in literature, including observations of fracture surfaces and relationships between surface roughness and material strength, are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Effect of Grain Boundary Facet Junctions on Segregation and Embrittlement

Junctions are discontinuities in flat grain boundaries that arise in all polycrystalline materials and are thought to play important roles in the response of a grain boundary network to thermal and mechanical loads. A key open question concerns the mechanisms by which solute segregation to junctions impacts properties of the grain boundary. Here, in this work, we investigate the influence of grain boundary facet junctions on solute embrittlement, and we present an analytical model that uses the hydrostatic stress field contributed by dislocations at multiple junctions to describe these effects. Specifically, we study junctions between {112} facets of various lengths in Au $\langle111\rangle$ Σ3 tilt grain boundaries. Copper and silver solutes are employed to determine if the effect of junctions on solute segregation and embrittlement is dependent on size relative to the host. Combined, atomistic simulation data and the analytical model show that Cu and Ag have opposite segregation responses to junctions due to the sign of the hydrostatic stress field induced by junctions. However, a positive shift in the embrittling potency is computed near junctions regardless of solute type or the stress state of the segregation site. Hence, for the conditions studied, junctions consistently shift the energetic landscape towards embrittlement.

36 MATERIALS SCIENCE↗