Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shear modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Shear strength measurements and hydrostatic compression of rhenium diboride under high pressures

Shear strength measurements have been carried out on rhenium diboride, ReB 2 , to a pressure of 74 GPa using a Radial X-ray Diffraction (R-XRD) technique in a diamond anvil cell using platinum as an internal x-ray pressure standard. The R-XRD result has provided a unique insight into the deformation of hexagonal crystal lattice under non-hydrostatic compression and variation of shear strength with increasing pressure. From R-XRD data, we have estimated hydrostatic component of compression to determine an equation of state of rhenium diboride yielding a bulk modulus of K 0 = 366 ± 25 GPa with a pressure derivative $K^{'}_{0}$ = 4.3 ± 0.5 in good agreement with hydrostatic density functional theory calculations. Here, the average lower bound of shear strength (τ) from various diffraction planes was then calculated using the measured interplanar d-spacing (d m ) and hydrostatic component of d-spacing (d p ) to be shown to approach 6.7 ± 0.4 GPa at 70 GPa. Our results show that the anisotropic compression effects observed in ReB 2 under hydrostatic compression are correlated to electronic structure changes under compression as predicted by theoretical calculations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Probing the shear-induced microstructure of a smectite clay aqueous suspensions using rheo-USANS and rheo-SIPLI measurements

Hypothesis: The static microstructure of aqueous sodium-montmorillonite (Na-Mt) suspensions at low ionic strengths (where Particle Size/Debye Length ≈1) exhibits both the particle–particle ordering as well as aggregation with repulsive ordered domains having characteristic optical birefringence and attractive aggregated entities larger than 20 µm resulting in ever-increasing yield stresses also known as physical aging-rejuvenation behavior. We hypothesize that the attractive particle–particle aggregation is the underlying cause behind the physical aging-rejuvenation behavior observed in Na-Mt suspensions with no contribution from structural dynamics driven by repulsive particle–particle ordering or jamming. Experiments: We investigate the shear-induced microstructure of aqueous Na-Mt suspensions in the sol and gel state using rheo-ultra-small angle neutron scattering (rheo-USANS) experiments at shear rates of 1, 50, 500, and 2000 s −1 . We also perform rheo-shear-induced polarization light imaging (rheo-SIPLI) experiments to relate ordering with shearing and aging. Findings: Shearing the suspensions at low to moderate shear rates induces particle–particle aggregation and shearing at high shear rates induces the breakage of particle–particle aggregation in the sol and gel states, suggesting the microstructural aggregation in the sol and gel state is shear sensitive and a full rejuvenation or breakage of particle–particle aggregation is only achieved at a minimum critical shear rate. The rheo-SIPLI experiments reveal that the sol and gel state exhibited strong Maltese cross patterns at a shear rate of 1000 s −1 , indicating particle–particle ordering. Post shearing, the gel exhibited temporal evolution of storage modulus without any noticeable influence on the appearance of the Maltese cross pattern indicating physical aging and particle ordering are distinct length scale phenomena in Na-Mt suspensions and the physical aging-rejuvenation behaviour is a feature of particle–particle aggregation as opposed to ordering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Polyimide resin composites via in situ polymerization of monomeric reactants

Thermo-oxidatively stable polyimide/graphite-fiber composites were prepared using a unique in situ polymerization of monomeric reactants directly on reinforcing fibers. This was accomplished by using an aromatic diamine and two ester-acids in a methyl alcohol solvent, rather than a previously synthesized prepolymer varnish, as with other A-type polyimides. A die molding procedure was developed and a composite property characterization conducted with high modulus graphite fiber tow. Flexure, tensile, compressive, and shear tests were conducted at temperatures from 72 to 650 F on laminates before and after exposures at the given temperatures in an air environment for times up to 1000 hours. The composite material was determined to be oxidatively, thermally, and hydrolytically stable.

Cavano, P. J.↗
NASA NTRS1983

Thermal stresses in bonded solar cells - The effect of the adhesive layer

A two-dimensional, rectangular model of a proposed solar cell structure is analyzed as two plate elements bonded with an elastic continuum. The governing equations are formulated using the principle of minimum potential energy, with displacement components that vary linearly through the thickness of the adhesive layer. An approximate solution is constructed for a particular class of material properties and is characterized by a boundary layer near the unloaded edge. Both interface stress components achieve their largest values at the edge, and the maximum shear stress is independent of the Young's Modulus of the substrate.

Williams, H. E.↗
NASA NTRS1991

Deflection And Stress In Preloaded Square Membrane

Theoretical analysis yields equations for transverse deflection of, and stresses in, square membrane subject to both uniform transverse load and tension preloads applied uniformly along the edges. Follows energy/virtual-displacement approach. Basic equation expresses strain energy in membrane as double integral, over x and y coordinates of square, of function of longitudinal strains, shear strain, thickness of membrane, and Young's modulus and Poissons's ratio of membrane material.

Hermida, Alfonso↗
NASA NTRS1930

Strength in Shear of the Thin Curved Sheets of Alclad

This note is on an investigation made to obtain information on the strength of thin curved sheets of Alclad in shear. Designers may utilize this material as a strength member as well as for a covering for the wings and fuselages. A reduction may then be made in the size of the internal strength members. These experiments were undertaken with the object of securing the maximum value from the metal in this respect. The point at which buckling occurs is of primary importance. The buckling shear of a curved thin plate was determined mathematically and also experimentally. The following formula was obtained mathematically: s=K E t/r in which s is the unit shear, K is a constant, E is the modulus of elasticity, t is the thickness of the material, and r is the radius of curvature. The value of K as determined by the experiments was found to be .075. This formula applies only when s is within the elastic limit of the material. The breaking point of the material was obtained in most of the tests as a matter of information and the results are included in this report. The effect of the supporting ribs was determined by varying the number used.

Smith, George Michael↗
NASA NTRS2014

Improved Composites Using Crosslinked, Surface-Modified Carbon Nanotube Materials

Individual carbon nanotubes (CNTs) exhibit exceptional tensile strength and stiffness; however, these properties have not translated well to the macroscopic scale. Premature failure of bulk CNT materials under tensile loading occurs due to the relatively weak frictional forces between adjacent CNTs, leading to poor load transfer through the material. When used in polymer matrix composites (PMCs), the weak nanotube-matrix interaction leads to the CNTs providing less than optimal reinforcement.Our group is examining the use of covalent crosslinking and surface modification as a means to improve the tensile properties of PMCs containing carbon nanotubes. Sheet material comprised of unaligned multi-walled carbon nanotubes (MWCNT) was used as a drop-in replacement for carbon fiber in the composites. A variety of post-processing methods have been examined for covalently crosslinking the CNTs to overcome the weak inter-nanotube shear interactions, resulting in improved tensile strength and modulus for the bulk sheet material. Residual functional groups from the crosslinking chemistry may have the added benefit of improving the nanotube-matrix interaction. Composites prepared using these crosslinked, surface-modified nanotube sheet materials exhibit superior tensile properties to composites using the as received CNT sheet material.

polymer matrix composite↗
DOE OSTI2023

Assessment and Non-Destructive Evaluation of the Influence of Residual Solvent on a Two-Part Epoxy-Based Adhesive Using Ultrasonics

Polymers are increasingly being used in higher demanding applications due to their ability to tailor the properties of structures while allowing for a weight and cost reduction. Solvents play an important role in the manufacture of polymeric structures since they allow for a reduction in the polymer’s viscosity or assist with the dispersion of fillers into the polymer matrix. However, the incorrect removal of the solvent affects both the physical and chemical properties of polymeric materials. The presence of residual solvent can also negatively affect the curing kinetics and the final quality of polymers. Destructive testing is mainly performed to characterize the properties of these materials. However, this type of testing involves using lab-type equipment that cannot be taken in-field to perform in situ testing and requires a specific sample preparation. Here, a method is presented to non-destructively evaluate the curing process and final viscoelastic properties of polymeric materials using ultrasonics. In this study, changes in longitudinal sound speed were detected during the curing of an aerospace epoxy adhesive as a result of variations in polymer chemistry. To simulate the presence of residual solvent, samples containing different weight percentages of isopropyl alcohol were manufactured and tested using ultrasonics. Thermogravimetric analysis was used to show changes in the decomposition of the adhesive due to the presence of IPA within the polymer structure. Adding 2, 4, and 6 wt.% of IPA decreased the adhesive’s lap shear strength by 40, 58, and 71%, respectively. Ultrasonics were used to show how the solvent influenced the curing process and the final sound speed of the adhesive. Young’s modulus and Poisson’s ratio were determined using both the longitudinal and shear sound speeds of the adhesive. Using ultrasonics has the potential to non-invasively characterize the quality of polymers in both an in-field and manufacturing settings, ensuring their reliability during use in demanding applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1976

Strain rate effects on mechanical properties of fiber composites, part 3

An experimental investigation was conducted to determine the strain rate effects in fiber composites. Unidirectional composite specimens of boron/epoxy, graphite/epoxy, S-glass/epoxy and Kevlar/epoxy were tested to determine longitudinal, transverse and intralaminar (in-plane) shear properties. In the Longitudinal direction the Kevlar/epoxy shows a definite increase in both modulus and strength with strain rate. In the transverse direction, a general trend toward higher strength with strain rate is noticed. The intralaminar shear moduli and strengths of boron/epoxy and graphite/epoxy show a definite rise with strain rate.

Daniel, I. M.↗
NASA NTRSDate not supplied

Analytical Simulation of the Effects of Local Mechanisms on the Tensile Response of CMC Minicomposites

A micromechanics-based method based on a fiber shear lag analysis was developed to analyze the fast fracture response of uncoated ceramic matrix minicomposites under room temperature conditions. The model was applied to two SiCf/SiC minicomposite systems that were fabricated by Rolls-Royce and the University of Connecticut. The analysis approach does not require the assumption that matrix cracks propagate along the entire width of the minicomposite. The ratio of the fiber slip length to the crack spacing was found to be a key parameter driving the stress level at which the proportional limit takes place and the secondary modulus. Parametric studies were performed to investigate the effect of interfacial shear stress, fiber volume fraction and percentage of the composite that remains uncracked on the proportional limit stress and the composite secondary modulus. This work will allow increased understanding of the key material mechanisms that take place during the fast fracture loading and can be expanded to provide improved analysis methods for full macro composites. simulations to simulations of a flat panel impact test, have been performed to fully exercise and evaluate the capabilities of the developed model.

Micromechanics↗
DOE OSTI2022

Atomistic simulations of nanoindentation on nanoglasses: Effects of grain size and gradient microstructure on the mechanical properties

The use of nanoglass (NG) microstructures has been shown as an effective strategy to improve the ductility of rather brittle metallic glass alloys. To evaluate the effects of grain size and gradient design on the mechanical properties of NGs, we perform molecular dynamics simulations of nanoindentation on Cu 64 Zr 36 NGs. We consider samples with uniform 3 and 7 nm grain sizes as well as gradient microstructures with gradient grain sizes varying from 3 to 7 nm. Here, the results show that the deformation mechanism in NGs with small grain sizes is dominated by the activation and evolution of multiple shear transformation zones. Increasing grain sizes enhances the elastic modulus and hardness at the cost of reduced abrasion resistance. Though the average grain size at the indentation surface plays a crucial role in the deformation behavior of gradient NG models, their strain localization and plastic deformation states are affected by the grain sizes far from the indenter. Desired combinations of mechanical properties can be realized by different NG microstructure designs.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Fire and smoke retardant materials development

The research to provide a mechanism for dissipation of impact energy in filled polymers by using fillers with a low modulus coating is reported which will dissipate energy through shearing and crazing instead of fracture. The approach offers the advantages of low cost, low toxicity, and applicability to various resins.

Mueller, W. A.↗
NASA NTRS1998

IM7/LARC(tm) MPEI-1 Polymide Composites

LARC(Trademark) MPEI-1 (Langley Research Center(Trademark) modified phenylethynyl imide-1) phenylethynyl containing aromatic polymide, is based on the reaction of biphenyl dianhydride (BPDA), 3,4'-oxydianiline (3,4'-ODA), 1,3-bis(3-aminophenoxy)benzene (APB), 2,4,6-triaminopyrimidine (TAP) and 4-phenylethynyl phthalic anhydride (PEPA), presumably resulting in a mixture of linear, branched and star shaped phenylethynyl containing imides which was evaluated as a matrix for high-performance composites. The poly(amid acid) solution of MPEI-1 in N-methypyrrolidinone was synthesized at 35% and 42% solids. Unidirectional prepreg was fabricated from these solutions and Hercules IM7 carbon fiber utilizing NASA- Langley's multipurpose prepreg machine. The temperature-dependent volatile depletion rates, thermal crystallization behavior and resin theology were characterized. Based on this information, a composite molding cycle was developed which yielded well consolidated, void-free laminates. Composite mechanical properties such as short beam shear strength, longitudinal and transverse flexural strength and flexural modulus, longitudinal tensile strength and notched and unnotched compression strengths were measured at room temperature (RT) and elevated temperatures. These mechanical properties are compared with those of IM7/LARC(Trademark) PETI-5 composites.

Hou, T. H.↗
DOE OSTI2021

Comparison of the Mechanical Properties of a Conjugated Polymer Deposited Using Spin Coating, Interfacial Spreading, Solution Shearing, and Spray Coating

The mechanical properties of π-conjugated (semiconducting) polymers are a key determinant of the stability and manufacturability of devices envisioned for applications in energy and healthcare. These properties—including modulus, extensibility, toughness, and strength—are influenced by the morphology of the solid film, which depends on the method of processing. To date, the majority of work done on the mechanical properties of semiconducting polymers has been performed on films deposited by spin coating, a process not amenable to the manufacturing of large-area films. Here, we compare the mechanical properties of thin films of regioregular poly(3-heptylthiophene) (P3HpT) produced by three scalable deposition processes—interfacial spreading, solution shearing, and spray coating—and spin coating (as a reference). Our results lead to four principal conclusions. (1) Spray-coated films have poor mechanical robustness due to defects and inhomogeneous thickness. (2) Sheared films show the highest modulus, strength, and toughness, likely resulting from a decrease in free volume. (3) Interfacially spread films show a lower modulus but greater fracture strain than spin-coated films. (4) The trends observed in the tensile behavior of films cast using different deposition processes held true for both P3HpT and poly(3-butylthiophene) (P3BT), an analogue with a higher glass transition temperature. Grazing incidence X-ray diffraction and ultraviolet–visible spectroscopy reveal many notable differences in the solid structures of P3HpT films generated by all four processes. Herein, while these morphological differences provide possible explanations for differences in the electronic properties (hole mobility), we find that the mechanical properties of the film are dominated by the free volume and surface topography. In field-effect transistors, spread films had mobilities more than 1 magnitude greater than any other films, likely due to a relatively high proportion of edge-on texturing and long coherence length in the crystalline domains. Overall, spread films offer the best combination of deformability and charge-transport properties.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Mechanical and electrical properties of graphite fiber-epoxy composites made from pristine and bromine intercalated fibers

The mechanical and electrical properties of pristine and bromine intercalated graphite fiber-epoxy composites were compared. The two types of composite were similar in terms of tensile modulus, tensile strength, and Poisson's Ratio. However, the interlaminar shear strength of the brominated composite was 18 percent greater than its pristine counterpart. Only slight differences were observed in flexural properties. A five-fold decrease was observed in the electrical resistivity of the brominated composite parallel to the axis of the fibers, resulting in a unidirectional resistivity of about 90 microOmega/cm. Transverse resistivity was unaffected. Both types of composite were subjected to a simulated lightning strike of 10 KJ (at a peak current of 150 kA), and the composite with the intercalated graphite exhibited less damage.

Jaworske, Donald A.↗
NASA NTRS1987

Damage growth in composite laminates with interleaves

The influence of interleaves on the fracture behavior of laminated composites is investigated. The geometry of the composite consists of a cracked layer, bonded between two half-planes, which is separated by thin, low modulus, interleaves. The interleaves are modeled as uncoupled tension and shear springs. A stress analysis is carried out for a crack which may grow up to and spread along the interface. Integral transform techniques are used to develop the solution in terms of singular integral equations. An asymptotic analysis reveals logarithmic singularities in the critical stresses for the case of a broken layer. The equations are solved numerically and the effect of damage on critical stresses is studied. Initial results indicate that the interleaf gives a significant reduction in stresses in the adjacent regions and, if properly selected, should result in a more damage tolerant laminate.

Goree, James G.↗
NASA NTRS2001

Polyimide Composites from 'Salt-Like' Solution Precursors

Four NASA Langley-developed polyimide matrix resins, LaRC(TM)-IA, LaRC(TM)-IAX, LaRC(TM)-8515 and LaRC(TM)-PETI-5, were produced via a 'saltlike' process developed by Unitika Ltd. The salt-like solutions (65% solids in NMP) were prepregged onto Hexcel IM7 carbon fiber using the NASA LaRC multipurpose tape machine. Process parameters were determined and composite panels fabricated. The temperature dependent volatile depletion rates, the thermal crystallization behavior and the resin rheology were characterized. Composite molding cycles were developed which consistently yielded well consolidated, void-free laminated parts. Composite mechanical properties such as the short beam shear strength; the longitudinal and transverse flexural strength and flexural modulus; the longitudinal compression strength and modulus; and the open hole compression strength and compression after impact strength were measured at room temperature and elevated temperatures. The processing characteristics and the composite mechanical properties of the four intermediate modulus carbon fiber/polyimide matrix composites were compared to existing data on the same polyimide resin systems and IM7 carbon fiber manufactured via poly(amide acid) solutions (30-35% solids in NMP). This work studies the effects of varying the synthetic route on the processing and mechanical properties of the polyimide composites.

Cano, Roberto J.↗