Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “school”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Understanding the Mechanism of Light and Elevated Temperature Induced Degradation of p-type Silicon Solar Cells (Final Report)

Light- and elevated-temperature-induced degradation (LeTID) was first discovered in multicrystalline Si (mc-Si) solar cells and was initially attributed to metal impurities. Later, LeTID was reported in Czochralski (Cz) and float-zone (FZ) Si, and is considered as an important efficiency loss mechanism in p-type passivated emitter rear contact (p-PERC) Cz Si solar cells. LeTID causes ~10% relative and permeant efficiency losses in these cells in warmer climate regions where the module temperature is > 50 °C. Unlike light-induced degradation (LID), which is also observed in p-PERC cells, LeTID is slower and takes weeks to months in the field to saturate. Another difference compared to LID is that regeneration in LeTID proceeds very slowly, and field regeneration could take > 25 years — essentially the life of the module. Unlike B-O defects that are responsible for LID, neither B nor O impurities are directly involved in LeTID. LeTID appears to be unique to p-type Si, and is also observed in Ga-doped Si. Currently, most experimental evidence relates LeTID to the injection of hydrogen present in the dielectric surface passivation layers, such as SiN x and Al 2 O 3 , into the monocrystalline Si (c-Si) bulk during the fast-firing step. The involvement of hydrogen is further strengthened by controlled studies that show that increasing the amount of hydrogen in the dielectric during fast-firing increases the degree of LeTID. Similar to LID, a regeneration process has been discovered for LeTID. Regeneration of LeTID defects occurs when samples are exposed to 2–4 Suns illumination at elevated temperatures of 140–220 °C for 2–15 hr. Given the slower kinetics of LeTID and sample regeneration compared to LID, this poses a challenge for the manufacturing and field reliability of p-PERC cells, which will be the leading photovoltaic technologies over the next decade. Therefore, there is a need to understand LeTID and develop strategies to mitigate this effect. The defect responsible for LeTID has been extensively studied with over 100 publications, but direct spectroscopic evidence of this defect’s structure is lacking. Without an atomistic understanding of the LeTID defect, it is difficult to assess the long-term efficacy of the current industrial mitigation strategies. This, in turn, has implications on energy production for tens of gigawatts of these cells that will be deployed yearly worldwide. Using electron paramagnetic resonance, we identified a defect associated with LeTID with a g-value of 2.006, which we attribute to an Si dangling bond in an extended defect such as a vacancy agglomerate with H possibly within or in close vicinity. These vacancy agglomerates are likely created during the firing process, during which time H atoms are also injected into the bulk from the hydrogenated SiN x dielectric layer. Our atomistic-level insight shows that the LeTID defect can be mitigated by targeted intrinsic defect engineering of the c-Si material through a slower pull rate of the Cz ingot or 1000 °C oxygen ambient processing of the Si wafer to reduce the vacancy concentration. This project was a collaborative effort between the Colorado School of Mines and the National Renewable Energy Laboratory.

14 SOLAR ENERGY↗
DOE OSTI2023

Advancing Energy Efficiency Through Workforce Training

This Final Technical Report summarizes the work done on to develop and implement the Energy Basics Training Tool with industry partners and the Pacific Northwest National Laboratory. This project leveraged existing infrastructure and content developed by DOE in the Building America Solution Center (BASC) and Building Science Education Solution Center (BSESC) to design model content sets for use in entry-level construction programs at the high school certificate, boot camp, and other entry level training programs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Shooter Alarm System Final Report FY23

Lawrence Livermore National Laboratory (LLNL) is developing a multiphysics sensor package for automatic live arms fire detection for use in schools, houses of worship, hospi tals, etc. The goal is to have a package the size of a common smoke or CO2 detector with a price point of $50 or less which may be deployed throughout the aforementioned facilities. The commercial device will detect live gun fire with low probability of false alarm and auto matically alert first responders. A prototype board with four accelerometers, two infrared (IR) and two microphones has been developed and deployed at two experiments at LLNL’s Small Firearms Training Facility (SFTF). The device successfully and consistently measured signals on the accelerometer and acoustic channels. IR responses were measured depending upon the environment and sound source.

42 ENGINEERING↗
DOE OSTI2023

AMES: MS and MENG in Advanced Manufacturing for Energy at the University of Connecticut (Final Technical Report)

The objective of the project is to develop and implement an advanced degree program (MS and MENG in Advanced Manufacturing for Energy Systems, AMES) responding to the long-term workforce and technology requirements of the nation’s advanced energy products manufacturing industry. The program provided an industry relevant research experience by leveraging existing energy (e.g. fuels, power electronics, electrochemical power sources) and advanced manufacturing (e.g. additive manufacturing, composites, sensing) research at UConn funded by federal and state agencies, and industry, as well as through our industry partnerships. The trainees have joined research teams, advised by faculty with relevant research interests and expertise and were co-advised by industrial mentors. The AMES program have developed a truly interdisciplinary curriculum, first graduate degree program at UConn School (now College) of Engineering not housed in an academic department, with concentrations focusing on various challenges in advanced manufacturing for energy systems, e.g. advanced materials and processing. The project also developed new courses focusing on common technical and professional skills, and integrated various components for an industry relevant training. The program has admitted 29 Master of Science (MS) students since inception in January 2019. Twenty six of these students were AMES fellows, who have received partial funding from DoE through this project. The program far exceeded the goal of admitting at least five new MS (with thesis) students. All students were required to complete a thesis (M.S.) or a capstone (M.Eng.) project that are defined in collaboration with industry partners to ensure industrial relevancy, addressing a current industrial challenges. Industrial mentors also participated in advising the students in their research. AMES fellows, in addition were also required to complete an industrial internship for further industrial experience.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Seal Strength Calculations for Low Mass DDT Vessel

Lawrence Livermore National Laboratory (LLNL) is collaborating with Colorado School of Mines (Mines), to field the first dynamic experiments on the 3-ring flash radiography system (3-ring). One set of experiments for 3-ring concerns the deflagration to detonation transition (DDT), within a sealed column of high-explosives. The high-explosive material is ignited at one end with a BK-80, an igniter made from Boron Potassium-Nitrate (BKNO 3 ). The initial deflagration reaction will increase the pressure in the sealed vessel, resulting in the formation of a dense "plug" of material ahead of the deflagration front. The transition to detonation is thought to be related to the plug formation. Previous experiments have been able to resolve the plug geometry, but only in a two dimensional radio-graph. 3-ring offers a novel diagnostic tool which could provide three dimensional density fields via few-view reconstruction algorithms and computed tomography.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

First-generation college student forges ahead, now key to Lab's mission

Fatima Woody was just 17 and a student at Pojoaque Valley High School when she first started her career as a Los Alamos Neutron Science Center receptionist. Now she's in a crucial role that keeps plutonium pit production and other mission processes operating with as little interruption as possible. Over nearly four decades, Fatima has gradually advanced from her initial positions as a receptionist and administrative secretary to become a computer technician, then a computer system professional who specializes in project management. Today, she coordinates the workflow for nearly two dozen deployed information technology technicians who keep the computer systems and networks operating at the high-tech complex that houses the Lab's Plutonium Facility.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

End-to-end optimization for battery materials and molecules by combining graph neural networks and reinforcement learning

The National Renewable Energy Laboratory (NREL), together with the Colorado School of Mines (CSM) and Colorado State University (CSU), has developed a machine learning-enhanced approach to design new battery materials. Currently, such materials are designed in part via numerous expensive high-fidelity computational simulations that predict the performance of a given composition. Even with computational screening tools, the vast landscape of possible molecular or crystal structures exceeds current and future computational capacity. Improving the efficiency by which new materials can be optimized will therefore disrupt the cost, risk, and time required to bring new energy solutions to the marketplace. Predicting the properties of an organic molecule or periodic crystalline material given its structure has grown increasingly common. These approaches leverage large-scale computational and experimental databases and ML approaches such as graph neural networks. The inverse design problem of finding a material that possesses desired properties is substantially more challenging, since enumerating all valid material structures is not feasible. In this project, we leveraged recent success in reinforcement learning to efficiently navigate this high-dimensional search space. Just as algorithms can find the optimal chess moves from nearly limitless options, we train an approach to evolve a simple starting structure into a complex structure that possess the desired properties. Our solution has been demonstrated by applying it to two related design application tasks for short- and long-term energy storage, respectively: (1) the design of solid-state ion conductors and (2) the design of organic redox-active materials. The project has resulted an open-source software library for material design, documented examples of applying the library to both organic and inorganic material optimization, and peer-reviewed publications detailing the data, computational models, and resulting candidate materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Manatee County Clear Sky Assessment Process: Prioritizing Solar + Storage for Resilient Facilities & Communities

The Clear Sky Tampa Bay project was a 15-month collaborative research effort to support solar + storage deployment for community resilience in Florida. The Clear Sky Decision Support Toolkit is a collection of resources designed to support users in conducting solar + storage prioritization and feasibility screening assessments at critical facilities. The Tampa Bay Regional Planning Council worked with four local governments in the region to test and apply the Toolkit. This case study series describes how each partner government used the Toolkit and highlights key insights and lessons learned that other users could follow to replicate the process. Manatee County applied the Clear Sky Decision Support Toolkit to two of the county's critical facilities: Nolan Middle School, which serves as a special needs emergency shelter, and its Public Safety Complex (PSC), which houses critical services including emergency management, communications, and medical services, traffic control, and more. The PSC serves as the Emergency Operations Center during activation events. The Clear Sky assessment process improved interagency communication and coordination and informed siting decisions for a potential solar + storage system for the Manatee County PSC.

14 SOLAR ENERGY↗
DOE OSTI2024

The Delicate Balance Redux: The Role of Nuclear Forces, Damage Limitation and Uncertainty in Future U.S.-China Crises

What is the impact of damage limitation capabilities like counterforce and missile defenses on deterrence, when their efficacy in stopping an adversary nuclear attack is uncertain? This is a key unanswered question to understand “how much is enough” for the United States to deter China and Russia in future nuclear crises. In this paper we extend an established, single move game theory model to capture the dynamics of two players in a nuclear crisis having varying damage limitation capabilities with uncertain effectiveness. Our model formalizes the logic of the “delicate balance” school of deterrence, which states that leverage in a crisis is driven by the risk each player can take with their combined strategic forces, and that those risks carry uncertainty as nuclear forces are hard to deliver against technologically advanced adversaries. Our model shows that damage limitation capabilities—even those with significant uncertainty around them like cyber or electronic warfare—can drive bargaining outcomes in an array of nuclear crises. We then apply these bargaining outcomes to the expected U.S.-China strategic balance as China builds out its nuclear force through 2035. We apply published force exchange models to determine the expected damage each side will be able to deliver, and we use these values to determine the likelihood that the U.S. can prevail in crises of varying stakes. Last, we show that U.S. policymakers have an array of options to improve future bargaining outcomes, evaluating how additional nuclear forces trade against improvements in damage limitation.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

Notice of Submittal – 2023 Radionuclide Air Emissions Report for Los Alamos National Laboratory

This report describes the emissions of airborne radionuclides from operations at Los Alamos National Laboratory (LANL) for calendar year 2023 and the resulting off-site dose from these emissions. This document fulfills the requirements established by the National Emissions Standards for Hazardous Air Pollutants in 40 CFR 61, Subpart H – Emissions of Radionuclides other than Radon from Department of Energy Facilities, commonly referred to as the Radionuclide NESHAP or Rad-NESHAP. Compliance with this regulation and preparation of this document is the responsibility of LANL’s Rad NESHAP compliance program, which is part of the Environmental Protection and Compliance (EPC) Division. The information in this report is required under the Clean Air Act and is being submitted to the U.S. Environmental Protection Agency (EPA) Headquarters and EPA Region 6. The highest effective dose equivalent (EDE) to an off-site member of the public was calculated using procedures specified by the EPA and described in this report. LANL’s EDE was 0.43 for 2023. The annual limit is 10 millirem per year, established by the EPA in 40 CFR 61 Subpart H. All measured air emissions are modeled to a single location, known as the Maximally Exposed Individual (MEI). During calendar year 2023, LANL continuously monitored radionuclide emissions at 28 “major” release points, or stacks. The Laboratory estimates emissions from an additional 59 “minor” release points using radionuclide usage source terms in lieu of stack monitoring. Also, LANL uses an EPA approved network of air samplers around the Laboratory perimeter to monitor ambient airborne levels of radionuclides. To provide data for dispersion modeling and dose assessment, LANL maintains and operates several meteorological monitoring towers. From these various systems, a comprehensive evaluation is conducted to calculate the MEI dose for the Laboratory. The MEI can be any member of the public at any off-site location where there is a residence, school, business, or office. In 2023, this MEI location was a business at 129 New Mexico State Road 4 (NM-4), located in the northern end of White Rock. The primary contributors to the off-site dose at this location are the ambient air data at that location combined with the collected potential emissions from unmonitored (minor) sources. Overall, the MEI dose in 2023 is similar to that which has been observed in recent years, and it remains well below the EPA’s 10 millirem per year limit. Doses reported to the EPA for the past 10 years are shown in Table E1.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Reimagining DOE Lab-University Partnership for the AI Era

This report describes observations and suggestions from a workshop on needs for partnerships between national laboratories and universities in the AI era. The workshop took place over two days in March of 2024 at Texas A&M University’s Bush School of Government and Public Service Washington, D.C., teaching site. Through good fortune this happened to be at the peak of cherry blossom season and the weather was beautiful. In attendance were professors and leadership from universities across the nation, members of four national laboratories, and a representative of the Office of Critical and Emerging Technologies in Department of Energy (DOE). This group spanned a broad range of disciplines—applied mathematics, materials science, nuclear security, intelligence, and more. The workshop also had the benefit of insights from Charlie McMillan, former director of Los Alamos National Laboratory, and retired Air Force Lieutenant General Jack Shanahan, who led AI efforts at the Pentagon.

42 ENGINEERING↗
DOE OSTI2024

Metal-to-Ceramic Joining Methods to Support Development of Advanced Ceramic-Based CSP Components

The National Renewable Energy Laboratory, Missouri University of Science and Technology (MS&T), Massachusetts Institute of Technology (MIT), and Colorado School of Mines (CSM) collaborated to design, develop, and test a material concept at bench scale which will be used to achieve a ceramic-to-metal (C2M) joint between a selected metal HTF loop material and a selected ceramic material used by the Gen3 CSP technology pathway. The final joint assembly will need to possess sufficient mechanical properties to withstand static high-temperature (650 degrees-700 degrees C) and high-pressure (20 MPa) and thermal cycling (between 650 degrees C and 100 degrees C) conditions. The material concept consists of three key components: (1) a ceramic matrix composite (CMC) that serves as a compliant transition material aiming to mitigate the stresses due to the mismatch of coefficient of thermal expansion (CTE) from a direct ceramic-to-metal joint, (2) a metal-end joint utilizing a multi-principal element alloy (MPEA) with changing percentage of particle loading to bond the candidate metal to the CMC, and (3) a ceramic-end joint utilizing a glass ceramic to bond the candidate ceramic to the CMC.

14 SOLAR ENERGY↗
DOE OSTI2024

Theranostic Radiopnictogens: 71 As, 72 As, and 119 Sb (Final Technical Report)

This project has developed new methods for the cyclotron production of medically relevant radionuclides 71 As and 119 Sb. Arsenic and antimony are chemically homologous elements (group 5A, also known as the pnictogens) that have radionuclides that are of considerable interest within nuclear medicine. Such radiopnictogens include the potentially therapeutic radionuclides 119 Sb (t 1/2 = 38 h) that decays with the emission of 24.5 low energy, high potency electrons per decay with little concomitant photon radiation and 77 As (t 1/2 = 39 h) that decays with average beta energy of 230 keV and diagnostic nuclides 71 As (t 1/2 = 65 h, 28% β+) and 72 As (t 1/2 = 26 h, 80% β+) for positron emission tomography (PET). This work has had major success developing new methods for the cyclotron production and radiochemical isolation of 71 As, supporting parallel developments for 119 Sb, and assessing the chemical similarities between these two homologous radionuclides. This project brought into collaboration two universities with complimentary skill sets, proficiencies, expertise, and facilities: the University of Wisconsin (UWisc) and the University of Missouri (Mizzou). Professors Ellison and Engle have experience in the small cyclotron production and radiochemical isolation of radionuclides, including 72 As and 119 Sb. Their recently developed metallurgic methods for fabricating cyclotron targets have great potential to expand and allow for the biomedical cyclotron production of long- lived, lower positron energy 71 As. Professors Hennkens and Jurisson have significant experience in the reactor production, radiochemical isolation, and biological functionalization of radioarsenic. Recent development of trithiol-based chelator molecules for functionalizing radioarsenic provide a platform for the investigation of the fundamental challenges of the promising low-energy-electron emitter, 119 Sb. Through their positions within their respective University’s graduate schools, the PIs and Co-Is effectively trained of graduate students and postdoctoral researchers in nuclear and radiochemistry, sub-specialties specifically identified in the Department of Energy (DOE) Office of Science Isotope Program long-range plan. Annual laboratory research visits for students between UWisc and Mizzou provided essential broad-field experience and scientific networking that is critical for maintaining their path along the training pipeline to productive careers in isotope production. This research collaboration has provided significant benefits to the DOE University Isotope Network and radionuclide-using researchers around the country.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

Prefeasibility Assessment for Solar PV and Storage for Critical Community Facilities in Chernihiv, Ukraine [Slides]

A prefeasibility analysis is performed for integrating solar photovoltaics and battery energy storage at four critical facilities in Chernihiv, Ukraine. The facilities were identified by Chernihiv city officials and include Hospital No. 2, the Maternity Hospital, Secondary School No. 11, and Preschool No. 4. The analyses were performed using NREL's REopt decision-support software tool. The analysis identifies potential capacities for PV and battery energy storage to provide both economic and resilience benefits. The conceptual architecture and estimates of key summary financial and performance metrics are presented.

14 SOLAR ENERGY↗
DOE OSTI2024

Western States Building Energy & Controls Apprenticeship (BECA) Program

How does this project help to understand the challenges of workforce development in the commercial building energy management industry? The purpose of this project was to create a replicable, scalable, and portable apprenticeship program for building energy management and controls. This paper will demonstrate how local processes can be more adaptable and inclusive than federal processes in achieving workforce development goals. Our work provides insights into the technical effectiveness of the program, enabling others to achieve greater success in their workforce development initiatives. The project required more time and financial resources than initially anticipated and spent a year in a no-cost extension working to accomplish the Statement of Project Objectives. The original goal was to create an Industry Related Apprenticeship Program (IRAP). The development of this apprenticeship presented challenges due to the lack of existing programs for reference and the absence of relevant industry classification codes by the Department of Labor (DOL). Notably, the role of a commercial building energy analyst is not recognized by the DOL. The SIC (industry codes) do not have a good description of this job. There are many that may fall into related categories, but none are the actual duties of an energy analyst. Discussions with the DOL indicated that substantial groundwork was necessary before a national apprenticeship program could be implemented, causing delays in the program’s commencement. As a result, students experienced longer wait times before starting their apprenticeship component. The apprenticeship program officially launched on September 14, 2021. The success of the State of Oregon’s apprenticeship program, the first of its kind in the state, underscored the flexibility and effectiveness of local initiatives compared to federal efforts. The COVID-19 pandemic also significantly impacted the project’s success. Beginning in March 2020, the pandemic led to widespread closures of schools and colleges by fall 2020. By September 2021, when the apprenticeship option became available, enrollment in colleges and universities nationwide had decreased, affecting student participation in the program. Moreover, as employers transitioned their employees to remote work, there was limited interaction with external personnel, influencing the willingness of training agents (employers) to integrate additional workers into their teams. This paper addresses several challenges encountered during the project, with the hope that future workforce development efforts will benefit from these experiences. We Final Technical Report 4 | Page encourage others to engage with state and federal agencies to enhance and update pathways for workforce development and apprenticeship programs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Empowering Rural Electrification in Honduras: An Integrated Assessment of PV/BESS and Productive Uses of Electricity in Gracias a Dios

Honduras faces significant challenges in its energy sector, particularly in rural areas where access to reliable and affordable electricity remains limited. The flagship rural electrification initiative for Honduras Secretary of Energy (SEN) is the Politica de Acceso Universal a la Electricidad (PAUEH - Universal Electricity Access Policy), a key solution for addressing this energy poverty is the deployment of more than 1700 distributed solar and hybrid mini-grid solutions. In late 2023 as a first step towards supporting SEN's electrification efforts, the National Renewable Energy Laboratory (NREL) developed a literature review of SEN electrification policy documents and conducted a series of technical capacity-building workshops with SEN and other energy sector stakeholders in Honduras focused on using NREL's open-source REopt tool to conduct techno-economic assessments and develop least-cost optimizations for potential solar + storage mini-grid systems. Building on some initial capacity building on mini-grid modeling, the National Renewable Energy Laboratory (NREL) worked with SEN to develop a detailed techno-economic assessment for electrifying two schools, a healthcare clinic, and a hospital in a hypothetical community within the department of Gracias a Dios. The analysis also evaluates the business case for cold storage productive use of energy (PUE) applications for the fisheries value chain and how the incorporation of these PUE loads potentially impacts both the viability of the PV+BESS solutions as well as local economic development. By assessing the potential for deployment of integrated PV/BESS systems to both support critical community services like education and healthcare, as well as potential for downstream enterprise and economic development, this analysis represents a first step that can help to inform specific strategies for development of pilot PV+BESS projects aligned with national priorities and sector level planning under PAUEH.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Electric Medium- and Heavy-Duty Vehicle Charging Infrastructure Attributes and Development

Although more established for light-duty vehicles (LDVs), advancements in electric vehicle (EV) charging technology are being made in the medium- and heavy-duty (MD/HD) sector. Progress is also being made with the electrification of MD/HD vehicles, including transit buses, school buses, MD trucks, and HD trucks. The diverse set of operational requirements and duty cycles for each vocation, as well as the range in the size of fleets, present unique charging and infrastructure requirements. This report focuses on charging requirements for MD/HD vehicles and synergies with LDV infrastructure. This analysis leans toward the qualitative rather than quantitative because relevant model inputs are in development and will not be established for a few years, as EV deployments are more mature in the LDV sectors than MD/HD. The report begins with an overview of MD/HD vehicle classes and types of charging, including depot and residential charging, among others (Section 2). Section 3 analyzes the home bases (overnight dwell locations) of existing MD/HD vehicles, with an emphasis on depot and residential home bases, and discusses implications for charging infrastructure. Section 4 discusses the key characteristics for determining if, when, and where MD/HD vehicles can leverage LDV charging infrastructure rather than requiring dedicated chargers. These considerations include electricity demand, connectors, physical space requirements, payment considerations, and impacts on the grid. Section 5 summarizes shared characteristics for MD/HD vehicles that are appropriate for near-term electrification and includes a summary of the outlook of the electric MD/HD vehicle market. The conclusion (Section 6) summarizes the report's findings and outlines areas for future research.

24 POWER TRANSMISSION AND DISTRIBUTION↗