Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “module temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Report on ISR-1 High-Altitude Balloon Flight

To test small technologies at lower cost for space science applications, LANL has developed a small high altitude balloon payload that could, in the future, be regularly and inexpensively launched from LANL. A neutron detector, NEMO, was integrated to evaluate its performance in a space-like mixed-radiation environment and collect neutron data in the atmosphere. In collaboration with EES-14, a high-altitude balloon payload was launched from LANL Technical Area 51 on February 27, 2023 and April 17, 2023. For real-time geolocation, a SAM-M8Q M8 GNSS module was used to get position and time, and an Iridium RockBLOCK 9603 was used to communicate with the ground using the Iridium satellite fleet. These modules were all controlled using an Iteaduino Mega microcontroller board. Finally, a High Altitude Science Eagle Flight Computer with a temperature pressure sensor ran independently, writing data to an SD card. All of these modules were powered by a 5 mAh lithium polymer battery. The battery was attached to the bottom of the payload while the remaining electronics were embedded in the underside of the top of the payload. These modules were wired as seen in Figure 1-2. The Iteaduino Mega microcontroller board was programmed to use the RockBLOCK to send a message once every 10 minutes containing neutron and GPS data read off the NEMO and SAM M8Q, respectively. Once the message send attempt finished, the RockBLOCK would be slept for the rest of the 10 minute interval. The Eagle Flight Computer ran continuously throughout the flight, taking data every 6 seconds. The RockBLOCK message data was set up to be delivered from the Iridium satellite fleet to a website, where it was stored and parsed to create live maps and plots for analysis and balloon retrieval. The RockBLOCK message data was additionally configured to be sent to an email as a fail-safe. The payload was ground-tested successfully for over 50 hours, with multiple revisions occurring to best prepare for conditions at altitude and improve the software and firmware to fix any issues that cropped up with the data pipeline. Additional to the balloon payload, the flight had an attached iMet-4 radiosonde and Garmin T5 GPS Dog Collar. The radiosonde provided GPS and meteorological data. The T5 dog collar is used along with a Garmin Astro 430 to track the balloon at a range of up to 9 miles for retrieval. The balloon itself was initially a 1600 g meteorological balloon with an attached High Altitude Science parachute, both of which can be seen in Figure 1-3. After the first flight, the EES team swapped to a Rocketman parachute.

42 ENGINEERING↗
DOE OSTI2024

Disorder and diffuse scattering in single-chirality (TaSe 4 ) 2 ⁢I crystals

The quasi-one-dimensional chiral compound (TaSe 4 ) 2 I has been extensively studied as a prime example of a topological Weyl semimetal. Upon crossing its phase transition temperature $T$ CDW ≈263K, (TaSe 4 ) 2 I exhibits incommensurate charge density wave (CDW) modulations described by the well-defined propagation vector ∼(0.05,0.05,0.11), oblique to the TaSe 4 chains. Although optical and transport properties greatly depend on chirality, there is no systematic report about chiral domain size for (TaSe 4 ) 2 I. In this study, our single-crystal scattering refinements reveal a bulk iodine deficiency, and Flack parameter measurements on multiple crystals demonstrate that separate (TaSe 4 ) 2 I crystals have uniform handedness, supported by direct imaging and helicity-dependent terahertz emission spectroscopy. Our single-crystal x-ray scattering and calculated diffraction patterns identify multiple diffuse features and create a real-space picture of the temperature-dependent (TaSe 4 ) 2 I crystal structure. Further, the short-range diffuse features are present at room temperature and decrease in intensity as the CDW modulation develops. These transverse displacements, along with electron pinning from the iodine deficiency, help explain why (TaSe 4 ) 2 I behaves as an electronic semiconductor at temperatures above and below $T$ CDW , despite a metallic band structure calculated from density functional theory of the ideal structure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Solar/Photovoltaic DC Systems: Information for Electrical Workers and Firefighters

Solar photovoltaic (PV) systems are common and continue to gain popularity. This article helps electrical workers and firefighters understand basic operating principles and hazards of PV dc arrays. The effects of solar radiation and temperature on power output are discussed including; PV-module testing standards; methods for calculating the number of modules in a PV string; some National Electrical Code (NEC) guidelines that are aimed toward improving array safety; dc-array commissioning, periodic maintenance, and testing; arc-flash-hazard potential ways firefighters can work safely around PV arrays; potential risks posed by moonlight and other light sources; some unique dc-system hazards. We also present statistics on PV dc-array electrical incidents and injuries.

14 SOLAR ENERGY↗
DOE OSTI2020

Sodium Ion Expansion Power Block for Distributed CSP

The Sodium Ion Expansion Power Block for Distributed CSP was a three-plus-one-year effort under the Concentrating Solar Power: Advanced Projects Offering Low LCOE Opportunities (CSP: APOLLO) funding program within the U.S. Department of Energy Solar Energy Technologies Office. The primary objective of this project is to develop a dual-stage modular sodium thermal electrochemical converter (Na-TEC) heat engine power block, which can be potentially integrated with either a small-scale dish solar or large-scale heliostats and parabolic trough CSP. Na-TEC is a heat engine that generates electricity through the isothermal expansion of sodium ions. The Na-TEC is a closed system that can theoretically achieve conversion efficiencies above 45% when operating between thermal reservoirs at 1150 K and 550 K. However, thermal designs have confined previous single-stage devices to thermal efficiencies below 20%. To mitigate some of these limitations, we consider dividing the isothermal expansion into two stages; one at the evaporator temperature (1150 K) and another at an intermediate temperature (650 K –1050 K). This dual-stage Na-TEC takes advantage of regeneration and reheating, and could be amenable to better thermal management. In light of this, we first designed and developed a thermo-electrochemical model, and thermodynamically demonstrated how the dual-stage device can improve the efficiency by up to 8% points over the best performing single-stage device. We also established an application regime map for the single- and dual-stage Na-TEC in terms of the power density and the total thermal parasitic loss. Moreover, a thermal design of an axisymmetric dual-stage Na-TEC is developed to guide the scale-up and fabrication of sub-components of prototype module. A reduced-order finite-element model is used in conjunction with a Na-TEC thermodynamic model that was developed to determine the total parasitic heat loss of this dual-stage design. A number of simplifications are applied in the reduced-order model to decrease the computational time while maintaining acceptable accuracy. According to this analysis, a maximum efficiency of 29% and a maximum power output of 125 W can be achieved. Ultimately, we were able to demonstrate thermal efficiency improvements of the Na-TEC heat engine from 19% up to 40.3%, in a dual-stage (non-optimized) prototype module that we designed, fabricated, and tested with high temperature stage at 923 K. Furthermore, a cost-performance analysis for this improved dual-stage design was carried out for distributed-CSP systems. A high-level techno-economic analysis (TEA) explores four scenarios where a Na-TEC is used as the heat engine for a distributed-CSP system. Overnight capital cost and levelized cost of electricity (LCOE) are estimated for a system lifetime of 30 years, revealing that overnight capital costs in a range from $3.57 to $17.71 per We are feasible, which equate to LCOEs from 6.9 to 17.2 cents/kWh e -1 . This analysis makes a significant contribution by concurrently quantifying the efficiency and unit costs for a range of multistage configurations, and demonstrating that a Na-TEC may be a promising alternative to Stirling engines for distributed-CSP systems at residential scale of 1–5 kW e .

14 SOLAR ENERGY↗
DOE OSTI2022

Fluid Properties for MOOSE

The Multiphysics Object-Oriented Simulation Environment (MOOSE) enables a wide range of advanced nuclear reactor simulations. Under the guidance of MOOSE's Finite Volume Team, we worked on the fluid properties module. Significant contributions include enabling Tabulated Fluid Properties (TFP) for systems thermal hydraulics analysis, Temperature and Pressure functionalized Fluid Properties, and Lead & Lead-Bismuth properties. Along with improving the capabilities of the fluid properties module, we also improved the documentation to allow for future users and developers to understand how the module works.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Habit–Dependent Vapor Growth Modulates Arctic Supercooled Water Occurrence

We present an analysis of long-term data collected at Utqiagvik, Alaska, to explore the impacts of cloud processes on the probability of finding supercooled water given cloud temperature, P(L|T), in the topmost unseeded liquid-bearing layers. P(L|T) has local minima at temperatures around –6°C and –15°C. Simulations using habit-evolving ice microphysics models suggest that these minima are the result of efficient vapor growth by non-isometric habits found at these temperatures. Here, we conclude that habit-dependent vapor growth of ice crystals modulates the macrophysical occurrence of supercooled water in polar clouds, the effect of which should be included in model parametrizations to avoid biases and/or error compensation. Our methodology is adaptable for spherical ice treatments implemented in models (example parametrizations provided), amenable for use with satellite measurements to give global impartial observational targets for model evaluations, and may allow empirical characterization of bulk responses to seeding and possibly secondary ice effects.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Electron Temperature Gradient Driven Transport Model for Tokamak Plasmas

A new model for electron temperature gradient (ETG) modes is developed as a component of the Multi-Mode anomalous transport module [T. Rafiq \textit{et al.,} Phys Plasmas \textbf{20}, 032506 (2013)] to predict a time dependent electron temperature profile in conventional and low aspect ratio tokamaks. This model is based on two-fluid equations that govern the dynamics of low-frequency short- and long-wavelength electromagnetic toroidal ETG driven drift modes. A low collisionality NSTX discharge is used to scan the plasma parameter dependence on the ETG real frequency, growth rate, and electron thermal diffusivity. Electron thermal transport is discovered in the deep core region where modes are more electromagnetic in nature. Several previously reported gyrokinetic trends are reproduced, including the dependencies of density gradients, magnetic shear, $\beta$ and gradient of $\beta$ $(\betap)$, collisionality, safety factor, and toroidicity, where $\beta$ is the ratio of plasma pressure to the magnetic pressure. The electron heat diffusivity associated with the ETG mode is discovered to be on a scale consistent with the experimental diffusivity determined by power balance analysis.

ETG↗
DOE OSTI2024

Development of The DOME Shield Model For The NRIC Virtual Test Bed

As several advanced reactor concepts are maturing, test beds are needed to accelerate the demonstration and deployment of these advanced nuclear technologies. The National Reactor Innovation Center (NRIC) is building new or enhancing existing US Department of Energy infrastructure to support testing of components and systems. Demonstration of Microreactor Experiments (DOME) will utilize the Experimental Breeder Reactor-II (EBR-II) dome containment structure to host reactor demonstrations. A reactor supplemental shielding is needed so that DOME dose requirements are met. To accelerate the confirmatory analysis required for the reactor demonstration, the NRIC Virtual Test Bed (VTB) is developing a virtual model of the DOME shield that will be made available on the VTB public repository. This will allow developers to leverage advanced modeling and simulation tools to ensure their reactor demonstration concept will meet dose requirement and the limit concrete temperature in the shield during steady state and transient operation conditions. This paper presents the model developed for the DOME shield using open-source tools: MOOSE heat transfer module, Monte Carlo code OpenMC, and Cardinal to calculate the DOME shield temperature distribution during steady state

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Effectiveness of Versalink 143 on Improving Shock Survival of Encapsulated Electronics

In the past, test-vehicle-mounted instrumentation modules that record sensor data during shock and vibration events have been coated with a polymer isolation layer to enhance survivability. This study uses finite element modeling to evaluate the effectiveness of the isolation material Versalink 143 on reducing stress in an instrumentation module. The modeling shows that while the isolation layer does attenuate stress due to high frequency shock and vibration, it also amplifies stress due to lower frequency shock and vibration. Thicker layers tend to attenuate high frequency stress more and amplify low frequency stress less. In addition, at higher test temperatures thermal expansion of the isolation layer can cause static stress in the module far greater than the stress due to shock, depending on how the module is constrained within the test vehicle. When designing and implementing vehicle- mounted instrumentation modules, the expected input shock spectrum, mounting constraints, and static effects of temperature must be carefully considered.

42 ENGINEERING↗
DOE OSTI2024

Field‐representative evaluation of PID‐polarization in TOPCon PV modules by accelerated stress testing

Abstract Potential‐induced degradation‐polarization (PID‐p) can reduce module power, but how to project the extent to which PID‐p may occur in field conditions considering the factors of system voltage, condensed moisture, temperature, and illumination has not been clarified. Using tunnel oxide passivated contact (TOPCon) modules, this work demonstrates a method to test full‐size crystalline silicon PV modules for PID‐p to provide field‐representative results. In initial screening tests with positive or negative 1000 V electrical bias applied at 60°C for 96 h using Al foil electrodes on the glass surfaces, the module type exhibited reversible PID‐p only on the front face when the cell circuit was in negative voltage potential. No PID was detected on the rear after testing in either polarity. We then evaluated the PID‐p sensitivity on the front side under different UV irradiances while maintaining the glass surface wet to estimate real‐world susceptibility to PID‐p. The magnitude of the observed behavior was fit using a previously developed charge transfer and depletion by light model. Whereas power loss with −1000 V applied to the cell circuit at 60°C for 96 h in the dark was about 30%, testing the module front under 0.051 W·m −2 nm −1 at 340 nm UVA irradiation using fluorescent tubes, the mean degradation was only 3%. When the modules were tested in the dark for PID‐p with in situ dark current–voltage (I‐V) characterization, the thermal activation energy for degradation was 0.71 eV; for recovery in the dark, it was 0.58 eV. Whereas recovery from the degraded state at 60°C in the dark without voltage bias was 5% absolute in 38 h, rapid recovery of about 5% absolute was observed with 1000 W·s/m 2 exposure at 25°C using a flash tester.

14 SOLAR ENERGY↗
DOE OSTI2020

Identity of the JET M-mode and the ASDEX Upgrade I-phase phenomena

An H-mode plasma state free of edge-localized mode (ELM), close to the L-H transition with clear density and temperature pedestal has been observed both at the Joint European Torus (JET) and at the ASDEX Upgrade (AUG) tokamaks usually identified by a low frequency (LFO, 1–2 kHz), m = 1, n = 0 oscillation of the magnetics and the modulation of pedestal profiles. The regime at JET is referred to as M-mode while at AUG as intermediate phase or I-phase. This contribution aims at a comparative analysis of these phenomena in terms of the density and temperature pedestal properties, the magnetic oscillations and symmetries. Lithium beam emission spectroscopy (Li-BES) and reflectometer measurements at JET and AUG show that the M-mode and the I-phase modulates the plasma edge density. A high frequency oscillation of the magnetics and the density at the pedestal is also associated with both the M-mode and the I-phase, and its power is modulated with the LFO frequency. The power modulation happens simultaneously in every Mirnov coil signal where it can be detected. The bursts of the magnetic signals and the density at the pedestal region are followed by the flattening of the density profile, and by a radially outward propagating density pulse in the scrape-off layer (SOL). The analysis of the helium line ratio spectroscopy (He-BES) signals at AUG revealed that the electron temperature is modulated in phase with the density, thus the I-phase modulates the pressure profile gradient. Overall, this analysis gave opportunity to compare Li-BES and He-BES density profiles at different locations suggesting a toroidal and poloidal symmetry of the density modulation. The presented results indicate that the regimes, the AUG I-phase and the JET M-mode, exhibit similar characteristics, which leads to the conclusion that the regimes are likely the same.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Self-powered Through-wall communication for dry cask storage monitoring

Many nuclear facilities, such as spent fuel storage dry casks and nuclear reactor pressure vessels, are entirely sealed by metal layers to prevent harmful radiation. For safety and security operations, the temperature, pressure, radiation, and humidity inside the vessel needs to be closely monitored. However, no practical technology is currently available to realize the through-wall data communication and monitoring for these vessels due to the inside harsh environment of high temperature and nuclear radiation. In this paper, an innovative self-powered wireless through-wall data communication system for the nuclear environment is presented, which demonstrates a successful solution to such challenges. The presented system is composed of four modules, i.e., energy harvester with power management circuits, ultrasound wireless communication using high-temperature piezoelectric transducers, electronic circuits for sensing and data transmission, and radiation shielding for electronics. Here, constitutive functions of each module were firstly designed and followed by the system integration. Experiments were conducted subsequently to validate the designed functions and evaluate the performance of the integrated system. Results showed that the average power of over 40 mW was harvested from the thermal flow inside the nuclear spent fuel canisters which could provide enough energy to operate the sensing and data communication systems. The gamma radiation test results showed that the thermoelectric energy harvester and ultrasound transceivers can withstand radiation dosing over 100 Mrad. Furthermore, temperature shock tests demonstrated that the entire system including the shielded electronics can survive and maintain their functionalities at temperatures as high as 195°C. Under the in-lab mocked-up high temperature conditions and radiation shielding, the proposed system is foreseen to survive and operate stably for fifty years inside a nuclear spent fuel canister, and send the frequency modulated data out of the canister for 3 s in every 10 min.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Field‐Relevant Degradation Mechanisms in Metal Halide Perovskite Modules

Field testing, failure analysis, and understanding of degradation mechanisms are essential to advancing metal halide perovskite (MHP) photovoltaic (PV) technology toward commercialization. Here, we present performance data from up to 1 year of outdoor testing of MHP modules in Golden, Colorado. The module encapsulation architecture and encapsulant materials have a significant impact on module reliability, with modules containing a polyolefin elastomer (POE) in addition to a desiccated polyisobutylene (PIB) edge seal outlasting modules with only a PIB edge seal or PIB blanket. Nondestructive and destructive characterization of the field-tested modules points to module scribes and interfaces as areas of potential mechanical weakness and chemical migration, resulting in shunt pathways and increased series resistance. Finally, indoor accelerated stress testing with light and elevated temperatures is performed, demonstrating failure with similar scribe degradation signatures as compared to the field-tested modules. In conclusion, under both outdoor testing and light and elevated temperature conditions, electrochemical corrosion between the copper electrode and the mobile iodine ions appeared dominant, with a significant progression at the scribes that is speculated to result from an interplay between the initial laser damage and joule heating from enhanced ion diffusion under bias.

14 SOLAR ENERGY↗
DOE OSTI2025

A-Cation-Dependent Structure–Optical Property Relationships of Halide Perovskite Heterostructures with Complex Interfaces

Halide perovskite heterostructures offer promising interfacial interactions for energy conversion, yet challenges in synthesizing structurally well-defined systems limit detailed investigations into structure–property relationships. In this article, we report the synthesis of compositionally controlled 3D/3D and 3D/2D halide perovskite heterostructures using evaporation crystallization-polymer pen lithography (EC-PPL) and a single-particle analysis of their properties. By systematically varying A-site cation combinations and crystal dimensions, we show that heterointerfaces induce local lattice distortions that modulate vibrational dynamics and electron-phonon coupling. These interfacial effects result in significantly extended carrier lifetimes compared to compositionally similar pure phases. Raman spectroscopy, temperature-dependent photoluminescence, and power-dependent emission analysis reveal that localized structural modulations at the interface govern exciton-phonon interactions. These effects are magnified in smaller crystals due to increased interfacial contributions. Our findings highlight the critical role of interface-driven lattice control in tuning the optoelectronic properties of halide perovskites and provide design principles for engineering heterostructures in next-generation optoelectronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

TESS Observations of the WASP-121 b Phase Curve

We study the red-optical photometry of the ultrahot Jupiter WASP-121 b as observed by the Transiting Exoplanet Survey Satellite (TESS) and model its atmosphere through a radiative transfer simulation. Given its short orbital period of ∼1.275 days, inflated state, and bright host star, WASP-121 b is exceptionally favorable for detailed atmospheric characterization. Toward this purpose, we use allesfitter to characterize its full red-optical phase curve, including the planetary phase modulation and secondary eclipse. We measure the day- and nightside brightness temperatures in the TESS passband as 3012{sub −42}{sup +40} and 2022{sub −602}{sup +254} K, respectively, and do not find a statistically significant phase shift between the brightest and substellar points. This is consistent with inefficient heat recirculation on the planet. We then perform an atmospheric retrieval analysis to infer the dayside atmospheric properties of WASP-121 b, such as its bulk composition, albedo, and heat recirculation. We confirm the temperature inversion in the atmosphere and suggest H{sup −}, TiO, and VO as potential causes of the inversion, absorbing heat at optical wavelengths at low pressures. Future Hubble Space Telescope and James Webb Space Telescope observations of WASP-121 b will benefit from its first full phase curve measured by TESS.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Fluctuating charge-density-wave correlations in the three-band Hubbard model

The high-temperature superconducting cuprates host unidirectional spin- and charge-density-wave orders that can intertwine with superconductivity in nontrivial ways. While the charge components of these stripes have now been observed in nearly all cuprate families, their detailed evolution with doping varies across different materials and at high and low temperatures. We address this problem using nonperturbative determinant quantum Monte Carlo calculations for the three-band Hubbard model. Using an efficient implementation, we can resolve the model’s fluctuating spin and charge modulations and map their evolution as a function of the charge transfer energy and doping. We find that the incommensurability of the charge modulations is decoupled from the spin modulations and decreases with hole doping, consistent with experimental measurements at high temperatures. These findings support the proposal that the high-temperature charge correlations are distinct from the intertwined stripe order observed at low-temperature and in the single-band Hubbard model.

42 ENGINEERING↗
DOE OSTI2023

Nanoscale visualization of the thermally driven evolution of antiferromagnetic domains in FeTe thin films

Antiferromagnetic order, being a ground state of a number of exotic quantum materials, is of immense interest both from the fundamental physics perspective and for driving potential technological applications. For a complete understanding of antiferromagnetism in materials, nanoscale visualization of antiferromagnetic domains, domain walls, and their robustness to external perturbations is highly desirable. Here, we synthesize antiferromagnetic FeTe thin films using molecular-beam epitaxy. We visualize local antiferromagnetic ordering and domain formation using spin-polarized scanning tunneling microscopy. From the atomically resolved scanning tunneling microscopy topographs, we calculate local structural distortions to find a high correlation with the distribution of the antiferromagnetic order. This is consistent with the monoclinic structure in the antiferromagnetic state. Interestingly, we observe a substantial domain-wall change by small temperature variations, unexpected for the low-temperature changes used compared to the much higher antiferromagnetic ordering temperature of FeTe. This is in contrast to electronic nematic domains in the cousin FeSe multilayer films, where we find no electronic or structural change within the same temperature range. Further, our experiments provide the atomic-scale imaging of perturbation-driven magnetic domain evolution simultaneous with the ensuing structural response of the system. The results reveal surprising thermally driven modulations of antiferromagnetic domains in FeTe thin films well below the Néel temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Data Files for P. Mai et al., "Fluctuating charge-density-wave correlations in the three-band Hubbard model" (2024)

The high-temperature superconducting cuprates host unidirectional spin- and charge-density-wave orders that can intertwine with superconductivity in nontrivial ways. While the charge components of these stripes have now been observed in nearly all cuprate families, their detailed evolution with doping varies across different materials and at high and low temperatures. We address this problem using nonperturbative determinant quantum Monte Carlo calculations for the three-band Hubbard model. Using an efficient implementation, we can resolve the model’s fluctuating spin and charge modulations and map their evolution as a function of the charge transfer energy and doping. We find that the incommensurability of the charge modulations is decoupled from the spin modulations and decreases with hole doping, consistent with experimental measurements at high temperatures. These findings support the proposal that the high-temperature charge correlations are distinct from the intertwined stripe order observed at low-temperature and in the single-band Hubbard model.

cuprates↗