Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “manufacturing automation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Automated Array Assembly, Phase 2

The large scale production of silicon solar cell array panels is discussed. The cost and performance of three manufacturing sequences designed to convert silicon sheet and wafers into solar panels is analyzed. The production of ion implanted and furnace annealed solar cells made using solar grade n- and p-type wafers is examined. The performance of production size lots is examined with regard to the relationship between the ion implant and furnace anneal parameters and the ability to form consistently good thick film screen printed contacts. The spray on antireflection coating process is evaluated. The performance of several lots of cells before and after coating is measured. The structure and refractive index of the RCA I (TiO2) coating is compared with commercial solutions. Sensitivity of coated, screen printed cells to the post heat treatment required to cure the films is assessed.

Daiello, R. V.↗
NASA NTRS2020

Hybrid AFP/Hand Layup Optimized Blades to Enhance Wind Tunnel Capability Summary of PREDICT 2018 Efforts

A project spanning four-months in 2018 was conducted at the NASA Langley Research Center (LaRC) to advance the state of the art in Automated Fiber Placement (AFP) fabrication of complex carbon fiber wind tunnel blades for NASA wind tunnels. This effort was the first step in developing a methodology for fabricating these complex parts. An AFP robotic system was used to explore whether manufacturing time and cost for production of wind tunnel blades could be reduced. Computer aided design models of the blade surfaces were created, and AFP process planning and programming was employed to study the manufacturability of the shapes. A manufacturing demonstration unit was fabricated to demonstrate a methodology to fabricate a complex shape representative of a wind tunnel blade. The present study revealed that the heater configuration on the LaRC AFP robotic system was the primary constraint that limited its ability to use AFP for wind tunnel blade manufacturing.

carbon-epoxy↗
DOE OSTI2020

Non-destructive simulation of node defects in additively manufactured lattice structures

Additive Manufacturing (AM), commonly referred to as 3D printing, offers the ability to not only fabricate geometrically complex lattice structures but parts in which lattice topologies in-fill volumes bounded by complex surface geometries. However, current AM processes produce defects on the strut and node elements which make up the lattice structure. This creates an inherent difference between the as-designed and as-fabricated geometries, which negatively affects predictions (via numerical simulation) of the lattice’s mechanical performance. Although experimental and numerical analysis of an AM lattice’s bulk structure, unit cell and struts have been performed, there exists almost no research data on the mechanical response of the individual as-manufactured lattice node elements. Here we propose a methodology that, for the first time, allows non-destructive quantification of the mechanical response of node elements within an as-manufactured lattice structure. A custom-developed tool is used to extract and classify each individual node geometry from micro-computed tomography scans of an AM fabricated lattice. Voxel-based finite element meshes are generated for numerical simulation and the mechanical response distribution is compared to that of the idealised computer-aided design model. The method demonstrates compatibility with Uncertainty Quantification methods that provide opportunities for efficient prediction of a population of nodal responses from sampled data. Overall, the non-destructive and automated nature of the node extraction and response evaluation is promising for its application in qualification and certification of additively manufactured lattice structures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Manufacturing Data and Machine Learning Platform: Enabling Real-time Monitoring and Control of Scientific Experiments via IoT

IoT devices and sensor networks present new opportunities for measuring, monitoring, and guiding scientific experiments. Sensors, cameras, and instruments can be combined to provide previously unachievable insights into the state of ongoing experiments. However, IoT devices can vary greatly in the type, volume, and velocity of data they generate, making it challenging to fully realize this potential. Indeed, synergizing diverse IoT data streams in near-real time can require the use of machine learning (ML). In addition, new tools and technologies are required to facilitate the collection, aggregation, and manipulation of sensor data in order to simplify the application of ML models and in turn, fully realize the utility of IoT devices in laboratories. Here we will demonstrate how the use of the Argonne-developed Manufacturing Data and Machine Learning (MDML) platform can analyze and use IoT devices in a manufacturing experiment. MDML is designed to standardize the research and operational environment for advanced data analytics and AI-enabled automated process optimization by providing the infrastructure to integrate AI in cyber-physical systems for in situ analysis. We will show that MDML is capable of processing diverse IoT data streams, using multiple computing resources, and integrating ML models to guide an experiment.

Machine Learning↗
NASA NTRS1978

Automated Array Assembly, Phase 2

The purpose of the overall program is to establish technological readiness and provide verification for the elements of a manufacturing sequence which would ultimately be suitable for the large-scale production of silicon solar-array modules at a selling price of less than $500/kW. A program and process plan for accomplishing this objective was developed and put into operation. Three junction-formation processes are shown; since cost analysis shows that they do not differ greatly in cost, each should be considered for technical merits and possible future cost reduction. The progress made in the various process steps of the plan is described, and conclusions are presented.

Daiello, R. V.↗
NASA NTRS1978

Development of pulsed processes for the manufacture of solar cells

The results of a 1-year program to develop the processes required for low-energy ion implantation for the automated production of silicon solar cells are described. The program included: (1) demonstrating state-of-the-art ion implantation equipment and designing an automated ion implanter, (2) making efforts to improve the performance of ion-implanted solar cells to 16.5 percent AM1, (3) developing a model of the pulse annealing process used in solar cell production, and (4) preparing an economic analysis of the process costs of ion implantation.

Minnucci, J. A.↗
NASA NTRS2015

NASA Automated Fiber Placement Capabilities: Similar Systems, Complementary Purposes

New automated fiber placement systems at the NASA Langley Research Center and NASA Marshall Space Flight Center provide state-of-art composites capabilities to these organizations. These systems support basic and applied research at Langley, complementing large-scale manufacturing and technology development at Marshall. These systems each consist of a multi-degree of freedom mobility platform including a commercial robot, a commercial tool changer mechanism, a bespoke automated fiber placement end effector, a linear track, and a rotational tool support structure. In addition, new end effectors with advanced capabilities may be either bought or developed with partners in industry and academia to extend the functionality of these systems. These systems will be used to build large and small composite parts in support of the ongoing NASA Composites for Exploration Upper Stage Project later this year.

Wu, K. Chauncey↗
DOE OSTI2024

Advanced silver sheathed 2212/Ag wire for high field magnets

Commercial High Temperature Superconductors (HTS) are all tape shaped (widths > 10 times thickness), because achieving useful current densities required them to be processed into this form, even though this also makes it more problematic to use them in some important coil types. Our product is based on 2212 (Bi2Sr2CaCu2O8) and it is the only HTS that can be processed into high current density wire forms that are similar to proven low temperature superconductors (LTS), while surpassing them in field generating and operating temperature capability. Required now are higher current density, lower cost and longer length 2212 wires to enable broad utilization where HTS tape usage is problematic. In Phase II we developed vital cost-lowering process technology elements and we test-processed longer wires with the standard commercial design as baseline and benchmark for our lower cost, higher quality and longer piece length wire advances. By initial application of Jc-boosting wire features, these wires exhibited significant performance increases. This Phase IIA program has now developed and qualified these technologies for lower cost, higher quality and longer piece length manufacturing in combination with current density-boosting wire features, paving the way to manufacturing capability that is essential for cost-effective commercial utilization of 2212 wire. Technical areas included automated, high uniformity powder packing, advanced drawing, annealing, lubricant cleaning and filament bundling, followed by integration of higher current density wire features and process variations.

17 WIND ENERGY↗
NASA NTRS1992

COINS: A composites information database system

An automated data abstraction form (ADAF) was developed to collect information on advanced fabrication processes and their related costs. The information will be collected for all components being fabricated as part of the ACT program and include in a COmposites INformation System (COINS) database. The aim of the COINS development effort is to provide future airframe preliminary design and fabrication teams with a tool through which production cost can become a deterministic variable in the design optimization process. The effort was initiated by the Structures Technology Program Office (STPO) of the NASA LaRC to implement the recommendations of a working group comprised of representatives from the commercial airframe companies. The principal working group recommendation was to re-institute collection of composite part fabrication data in a format similar to the DOD/NASA Structural Composites Fabrication Guide. The fabrication information collection form was automated with current user friendly computer technology. This work in progress paper describes the new automated form and features that make the form easy to use by an aircraft structural design-manufacturing team.

Siddiqi, Shahid↗
NASA NTRS2009

Lightning Pin Injection Testing on MOSFETS

Lightning transients were pin-injected into metal-oxide-semiconductor field-effect transistors (MOSFETs) to induce fault modes. This report documents the test process and results, and provides a basis for subsequent lightning tests. MOSFETs may be present in DC-DC power supplies and electromechanical actuator circuits that may be used on board aircraft. Results show that unprotected MOSFET Gates are susceptible to failure, even when installed in systems in well-shielded and partial-shielded locations. MOSFET Drains and Sources are significantly less susceptible. Device impedance decreased (current increased) after every failure. Such a failure mode may lead to cascading failures, as the damaged MOSFET may allow excessive current to flow through other circuitry. Preliminary assessments on a MOSFET subjected to 20-stroke pin-injection testing demonstrate that Breakdown Voltage, Leakage Current and Threshold Voltage characteristics show damage, while the device continues to meet manufacturer performance specifications. The purpose of this research is to develop validated tools, technologies, and techniques for automated detection, diagnosis and prognosis that enable mitigation of adverse events during flight, such as from lightning transients; and to understand the interplay between lightning-induced surges and aging (i.e. humidity, vibration thermal stress, etc.) on component degradation.

Ely, Jay J.↗
NASA NTRS2023

Human Systems Integration: Managing Risk in Anesthesia

The practice of anesthesia relies on clinicians’ ability to safely manage increasingly complex equipment. Devices such as ventilators, drug infusion pumps, and physiologic monitors use sophisticated algorithms to deliver care, but most clinicians are only trained to manage automated systems during normal operation. Few if any receive training on how to manage system failures. Although manufacturers are required to consult with human factors engineers as part of the equipment design process, most pieces of equipment are ultimately brought to market without extensive input from clinicians. Systems in the operating room can be as simple as an oxygen tank, or as complex as a multi-institutional healthcare organization. Humans are also a complex system, and play a critical role in the domains of operations, design, fabrication, maintenance, repair, and ultimately, dismantling and closeout. HSI seeks to provide a means for advocating the human side of the system. Human Systems Integration (HSI) is the cross disciplinary process used as part of the Systems Engineering process to reduce risk in systems. HSI professionals consider the human, hardware, and software elements of system design to optimize system performance and improve safety. HSI professionals work in domains of study that include training, management, human factors engineering, safety, and occupational health, among others. This article discusses the role of systems in the practice of anesthesia, and how consideration of the human during all phases of the system life cycle helps manage risks and promote a better patient outcome.

Human Factors↗
DOE OSTI2023

Techno-Economic Impact of a Smart Battery Sorting System

Create analytical framework to capture costs and benefits of the automated sorting into battery recycling including the development and deployment of various types of battery recycling technologies such as pyrometallurgical, hydrometallurgical, and direct recycling. Li Industries, Inc. is a Virginia startup company focused on reinventing how lithium-ion batteries (LIBs) are recycled. Li Industries is focused on developing direct LIB recycling and automated battery sorting technologies in order to reduce the environmental impact of the LIB lifecycle. This work is to be conducted in support of the American-Made Challenges Lithium-Ion Battery Recycling Prize. Li Industries and NREL will work together to understand how novel technologies, such as those being developed by Li Industries, can impact the development and economics of the battery recycling industry. This voucher is being used to evaluate the profitability of an automated sorting system developed by Li Industries and the potential effect this increased value could have on the domestic lithium-ion battery (LIB) recycling industries in the United States. NREL has developed the Lithium-Ion Battery Resources Assessment (LIBRA) system dynamics model to project the future viability of the US LIB manufacturing and recycling industries under varying technoeconomic conditions and battery adoption scenarios over the coming decades. Additional logic was added to LIBRA to analyze the role automated sorting of recycling feedstock could play in the buildout of the industry and the impacts it has on the recovery of end-of-life (EOL) battery materials. This report summarizes the outcomes of this modeling analysis in the US context through a series of sensitivity analyses run for a range of values of a given input dimension and compared across the unsorted or automated sorting cases for LIB recycling feedstock. For greater detail on the process and analysis, the researchers are publishing a forthcoming journal article titled Techno-Economic Impact of a Smart Battery Sorting System for Lithium-Ion Battery Recycling and Mineral Recovery in the United States by Weigl, et al. In the event the article is not accepted by any currently seeking publication in academic or industry journal, it may be published by NREL. CRADA benefit to DOE, Participant, and US Taxpayer: assists laboratory in achieving programmatic scope competencies, uses the laboratory's core competencies.

25 ENERGY STORAGE↗
NASA NTRS1990

Automating hypertext for decision support

A decision support system (DSS) shell is being constructed that can support applications in a variety of fields, e.g., engineering, manufacturing, finance. The shell provides a hypertext-style interface for 'navigating' among DSS application models, data, and reports. The traditional notion of hypertext had to be enhanced. Hypertext normally requires manually, pre-defined links. A DSS shell, however, requires that hypertext connections to be built 'on the fly'. The role of hypertext is discussed in augmenting DSS applications and the decision making process. Also discussed is how hypertext nodes, links, and link markers tailored to an arbitrary DSS application were automatically generated.

Bieber, Michael↗
NASA NTRS1991

Automated carbon dioxide cleaning system

Solidified CO2 pellets are an effective blast media for the cleaning of a variety of materials. CO2 is obtained from the waste gas streams generated from other manufacturing processes and therefore does not contribute to the greenhouse effect, depletion of the ozone layer, or the environmental burden of hazardous waste disposal. The system is capable of removing as much as 90 percent of the contamination from a surface in one pass or to a high cleanliness level after multiple passes. Although the system is packaged and designed for manual hand held cleaning processes, the nozzle can easily be attached to the end effector of a robot for automated cleaning of predefined and known geometries. Specific tailoring of cleaning parameters are required to optimize the process for each individual geometry. Using optimum cleaning parameters the CO2 systems were shown to be capable of cleaning to molecular levels below 0.7 mg/sq ft. The systems were effective for removing a variety of contaminants such as lubricating oils, cutting oils, grease, alcohol residue, biological films, and silicone. The system was effective on steel, aluminum, and carbon phenolic substrates.

Hoppe, David T.↗
DOE OSTI2022

Accelerating manufacturing for biomass conversion via integrated process and bench digitalization: a perspective

We present a perspective for accelerating biomass manufacturing via digitalization. We summarize the challenges for manufacturing and identify areas where digitalization can help. A profound potential in using lignocellulosic biomass and renewable feedstocks, in general, is to produce new molecules and products with unmatched properties that have no analog in traditional refineries. Discovering such performance-advantaged molecules and the paths and processes to make them rapidly and systematically can transform manufacturing practices. Furthermore, we discuss retrosynthetic approaches, text mining, natural language processing, and modern machine learning methods to enable digitalization. Laboratory and multiscale computation automation via active learning are crucial to complement existing literature and expedite discovery and valuable data collection without a human in the loop. Such data can help process simulation and optimization select the most promising processes and molecules according to economic, environmental, and societal metrics. We propose the close integration between bench and process scale models and data to exploit the low dimensionality of the data and transform the manufacturing for renewable feedstocks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2010

Automation of Commanding at NASA: Reducing Human Error in Space Flight

Automation has been implemented in many different industries to improve efficiency and reduce human error. Reducing or eliminating the human interaction in tasks has been proven to increase productivity in manufacturing and lessen the risk of mistakes by humans in the airline industry. Human space flight requires the flight controllers to monitor multiple systems and react quickly when failures occur so NASA is interested in implementing techniques that can assist in these tasks. Using automation to control some of these responsibilities could reduce the number of errors the flight controllers encounter due to standard human error characteristics. This paper will investigate the possibility of reducing human error in the critical area of manned space flight at NASA.

Dorn, Sarah J.↗
DOE OSTI2026

Virtual Inspection of Advanced Manufacturing via Process-Scale Digital Twins (Abbreviated Report)

Inspection and certification comprise the most significant bottlenecks in advanced manufacturing for NNSA applications, often requiring far more time and resources than the fabrication of the parts themselves. Traditional methods, such as manual review and X-ray computed tomography, are not only slow and costly, but also struggle to provide a clear connection between manufacturing instructions and the final performance of critical components. This gap limits both the agility and assurance needed to support the modernization and safety of the United States nuclear stockpile. In response, our Strategic Initiative established a digital twin framework that integrates realtime process monitoring, automated data analysis, and immersive virtual reality collaboration into a unified inspection pipeline. By leveraging data from sensors, machine instructions, and imaging, we created high-fidelity virtual models of manufactured parts that could be rapidly analyzed and certified. This approach was first demonstrated with Direct Ink Write, and then extended to other manufacturing settings, including conventional (or “subtractive”) manufacturing and to predict the end of life performance of parts per the aging and lifetimes programs. The result is a transformational capability: inspection times have been reduced by a factor of 120,000 without loss of accuracy and while simultaneously improving traceability and confidence in part quality. This framework not only streamlines certification for critical applications, but also positions the national security enterprise to respond more flexibly to emerging challenges, supporting agile manufacturing and digital engineering practices across a broad range of mission-relevant domains.

42 ENGINEERING↗
NASA NTRS1993

Automated Cutting And Drilling Of Composite Parts

Proposed automated system precisely cuts and drills large, odd-shaped parts made of composite materials. System conceived for manufacturing lightweight composite parts to replace heavier parts in Space Shuttle. Also useful in making large composite parts for other applications. Includes robot locating part to be machined, positions cutter, and positions drill. Gantry-type robot best suited for task.

Warren, Charles W.↗