Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “low voltage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

High-Voltage Potassium Hexacyanoferrate Cathode via High-Entropy and Potassium Incorporation for Stable Sodium-Ion Batteries

Prussian blue analogues (PBAs) used as sodium ion battery (SIB) cathodes are usually the focus of attention due to their three-dimensional open frame and high theoretical capacity. Nonetheless, the disadvantages of a low working voltage and inferior structural stability of PBAs prevent their further applications. Herein, we propose constructing the K x (MnFeCoNiCu)[Fe(CN) 6 ] (HE-K-PBA) cathode by high-entropy and potassium incorporation strategy to simultaneously realize high working voltage and cycling stability. In this study, the reaction mechanism of metal cations in HE-K-PBA are revealed by synchrotron radiation X-ray absorption spectroscopy (XAS), ex situ X-ray photoelectron spectroscopy (XPS), and in situ Raman spectra. We also investigate the entropy stabilization mechanism via finite element simulation, demonstrating that HE-K-PBA with small von Mises stress and weak structure strain can significantly mitigate the structural distortion. Benefit from the stable structure and everlasting K + (de)intercalation, the HE-K-PBA delivers high output voltage (3.46 V), good reversible capacity (120.5 mAh g –1 at 0.01 A g –1 ), and capacity retention of 90.4% after 1700 cycles at 1.0 A g –1 . Moreover, the assembled full cell and all-solid-state batteries with a stable median voltage of 3.29 V over 3000 cycles further demonstrate the application prospects of the HE-K-PBA cathode.

25 ENERGY STORAGE↗
DOE OSTI2025

Characterization of 4H-SiC Low Gain Avalanche Detectors (LGADs)

4H-SiC Low Gain Avalanche Detectors (LGADs) have been fabricated and characterized. The devices employ a circular mesa design with low-resistivity contacts and an SiO 2 passivation layer. The I–V and C–V characteristics of the 4H-SiC LGADs are compared with complementary 4H-SiC PiN diodes to confirm a high breakdown voltage and low leakage current. Both LGADs and PiN diodes were irradiated with alpha particles from a $^{210}_{84}$Po source. The charge collected by each device was compared, and it was observed that low-gain charge carrier multiplication is achieved in the 4H-SiC LGAD.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

A custom high-stability pulse generator for the test of a novel in-situ magnetic sensor developed to detect radiation damage in undulators

High-performance analog-to-digital converters (ADC) have been widely applied in many areas of science. For instance, magnetic field measurements based on the Faraday’s induction law require high-precision voltmeters to measure induced voltages. In this study in the context of free-electron lasers technology, the Magnetic Measurements Team at SLAC National Accelerator Laboratory proposed a novel in-situ radiation damage detection system (RDDS) for detecting small field variations in undulators. The system measures the flux change in a flexible printed-circuit coil attached to the magnet array during the undulator gap movement. The gap movement changes the magnetic field, which induces a voltage signal in the coil that is measured and integrated with an ADC. Although the system is capable of detecting relative flux changes better than 100 ppm, drift in the ADC’s gain or offset can cause apparent changes in the relative flux. This paper describes the first attempt to developed a high-precision verification circuit to perform ADC testing in the framework of the novel RDDS. The circuit generates a reference voltage pulse with a voltage–time integral relative precision better than 50 ppm for a few hundreds of mVs — the typical order of magnitude measured with the RDDS. The circuit’s design combines a fast and precise switch with a low-noise voltage reference. Long-term measurements allowed statistical analysis and showed that averaging the voltage–time integral of ten pulses gives the required 50 ppm stability. Moreover, reproducibility tests confirmed that the circuit’s output is invariable under small power supply instabilities and equipment shutdown. Instruments and applications designed to quantify the magnetic field by integrating voltage signals may use the pulse generator proposed in this paper for verification purposes.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Ionomer-free nanoporous iridium nanosheet electrodes with boosted performance and catalyst utilization for high-efficiency water electrolyzers

Increasing the catalyst utilization efficiency and simplifying electrode fabrication processes are crucial to accelerate development of low-cost proton exchange membrane electrolyzer cells (PEMECs). Here, we develop a facile route to fabricate ionomer-free iridium nanosheet integrated electrodes, in which nanoporous iridium nanosheets (IrNS) with abundant exposed edges and nanopores are deposited on thin titanium liquid/gas diffusion layers (TT-LGDLs) via a low-temperature chemical synthesis strategy. Further, benefiting from high catalytic activity, good electrode conductivity and excellent liquid/gas transport properties, such nanoporous IrNS electrodes with low catalyst loadings require low cell voltages of 1.65 V and 1.78 V at 3000 and 6000 mA/cm 2 , respectively. More impressively, a stable performance can be well maintained under extremely high current density tests of 5000 mA/cm 2 , demonstrating the potential of low-loading nanoporous IrNS electrodes in solid-electrolyte based electrochemical conversion cells that require high current density operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Reduced Common-Mode Voltage PWM Scheme for Full-SiC Three-Level Uninterruptible Power Supply With Small DC-Link Capacitors

In this article, a pulsewidth modulation (PWM) scheme for three-level full-SiC uninterruptible power supplies is developed to achieve a high power density. Two key passive components are selected for size reduction of the ac-ac stage: common-mode (CM) EMI filter, and dc-link capacitors. To reduce the CM noise, a new vector combination is proposed based on synchronous switching among three-phases. The proposed combinations align CM voltage (CMV) to be a single pulse per switching period. Owing to the simple shape, CMV cancellation between a three-level rectifier and inverter can be maximally utilized. A transition between the three combinations can control the drift of neutral point voltage. An equivalent carrier-based implementation is developed. Second, a simple algorithm to compensate neutral point voltage fluctuation is proposed both for differential mode (DM) and CM output voltage. Low-order harmonics on three-phase currents and an additional high-frequency CM noise by misaligned switching instant can be eliminated. The proposed compensation can be implemented by a simple correction on carrier slopes and injected zero-sequence voltage. The proposed PWM scheme is verified with 20-kW full-SiC UPS switching at 60 kHz with 140 μF dc-link capacitors.

42 ENGINEERING↗
DOE OSTI2022

Low-power anisotropic molecular electronic memristors

A molecular electronic memristor, programmable resistive memory device, promises to revolutionize next-generation flexible data storage units, offering fast, dense and ultralow power solutions. Here we report anisotropic resistive switching in molecular κ-(BEDT-TTF) 2 Cu[N(CN) 2 ]Cl memristors, consisting of alternatively segregated bis(ethylenedithio)tetrathiafulvalene (BEDT-TTF) and Cu[N(CN) 2 ]Cl layers. Electron resistance switching behavior controlled by charge tunneling in molecular memristors show a low set voltage of 0.5 V (10 V/cm) with the ON/OFF ratio of 2.3×10 3 along a-axis and a high-level endurance of 1.25×10 4 cycles along all axes. Finally, the findings of such molecular electronic crystals promise for low-power data storage memristors.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Sensorless Coil Detection Scheme based on Dead-Time Effect in Dynamic Wireless Power Transfer Systems

The detection of electric vehicles in dynamic wireless power transfer (DWPT) systems is important to reduce the standby losses and comply with the electromagnetic-field emission guidelines recommended by the International Commission for Non-Ionizing Radiation Protection. This paper discusses a novel sensorless coil detection scheme, which exploits the phenomenon of voltage-polarity reversal/notches caused by the dead-time effect in the full-bridge inverter. The variations in the system impedance and dead-time effects are collectively exploited to detect the receiver coil in the DWPT system. The proposed coil detection scheme is accomplished at low excitation voltage, which reduces the inverter standby losses. The theoretical analysis of the notch occurrence and open-loop simulation results are presented using a DWPT model developed in the piecewise linear electrical circuit simulation software.

Kavimandan, Utkarsh↗
DOE OSTI2020

Negligible voltage hysteresis with strong anionic redox in conventional battery electrode

Lattice anionic (oxygen) redox reactions (ARR) offers opportunities for developing high-capacity batteries, however, often suffers the notoriously high hysteresis in voltages and low initial coulombic efficiency. Particularly, ARR was widely considered inherent to these kinetic issues. Here, unambiguous evidences of strong and reversible ARR is found in Na 2/3 Ni 1/3 Mn 2/3 O 2 through mapping of resonant inelastic X-ray scattering (mRIXS). Strikingly, the material displays negligible voltage hysteresis (0.1 V) and high initial coulombic efficiency with a highly stable electrochemical profile. Our independent analysis of the Ni, Mn and O states consistently interpret the redox mechanism of Na 2/3 Ni 1/3 Mn 2/3 O 2 , which reveals a strong ARR system with facile kinetics and highly stable electrochemical profile that previously found only in cationic redox systems of conventional non-Alkali-rich materials.

25 ENERGY STORAGE↗
DOE OSTI2023

Reversible Electrochemical Lithium Cycling in a Vanadium(IV)- and Niobium(V)-Based Wadsley–Roth Phase

Fast charging remains one of the greatest safety challenges in Li-ion batteries due to Li-dendrite growth occurring on graphite anodes if they are lithiated too quickly. The search for high-rate anodes has highlighted materials in the Wadsley–Roth (WR) shear phase family. The relative abundance of V compared with traditional WR compositions of Nb and W makes V-based phases attractive. However, the high voltage and poor reversibility typically associated with V redox have made V-rich WR phases less studied than Nb- and W-rich phases. Here, we show that a new V-rich Wadsley–Roth phase, V 7 Nb 6 O 29 , achieves excellent rate capability and 80% capacity retention after 228 cycles with a relatively low average voltage of 1.76 V vs Li/Li + compared with other V-rich WR phases. Single-crystal X-ray diffraction reveals a P4/m space group with repeating 2 × 2 × ∞ and 3 × 3 × ∞ blocks of V 4+ and Nb 5+ octahedra. Finally, combined neutron pair distribution function analysis, X-ray absorption spectroscopy, and density functional theory calculations show that V redox is the primary source of capacity and that cycling stability is provided by the stable octahedral coordination adopted by V 4+ in the material.

25 ENERGY STORAGE↗
DOE OSTI2024

Lattice engineering of high-entropy olivine-type lithium metal phosphate as high-voltage cathodes

Engineering of high-entropy cathode materials for lithium-ion batteries has been actively pursued owing to the outstanding conductivity of high-entropy materials benefited from the maximum entropy and unique antisite disordering structure. Olivine lithium metal phosphates such as LiMnPO 4 and LiNiPO 4 feature high working voltages but low capacities due to their insulation nature. Here in this work, the synthesis of the high-entropy lithium metal phosphate materials (HELMPs) is realized by combining mechanochemistry with a calcination method. By regulating lattice of HELMPs, the high-entropy Li(Mn 0.35 Fe 0.35 Co0.1Mg 0.1 Ca 0.1 )PO 4 reveals three typical high-voltage plateaus in charge–discharge curves corresponding to the redox of Fe, Mn, and Co in the voltage range of 2.0–4.9 V vs Li + /Li, and a much higher initial capacity than LiMnPO 4 (104 vs 15 mAh g -1 ).

25 ENERGY STORAGE↗
DOE OSTI2026

Electrostatic Gating of Ionic Conductance through Heterogeneous van der Waals Nanopores

Nanofluidic ionic transistors typically require gate voltages above 1 V and operate only at submillimolar ionic strengths, limiting their biocompatible applications. We demonstrate ionic transistors consisting of single sub-10 nm nanopores drilled in van der Waals (vdW) heterostructures with internal gate electrodes made of few-layer graphene. These devices deliver up to 10-fold current modulation at gate voltages as low as 0.3 V in 10 mM KCl, and ∼2-fold modulation at near-physiological 100 mM KCl. Baseline conductance with no gate shows surface-charge-dominated transport below 100 mM KCl, consistent with negatively charged hBN walls and ∼5 nm opening of the pores. The surface charge and the electrochemical asymmetry introduced by the three-electrode configuration govern the device’s behavior: negative gate voltage (V G ) enriches ionic concentrations and enhances current, whereas positive V G induces a local depletion zone that suppresses transport. The current modulation by V G is dependent on the polarity of the transmembrane potential and leads to ion current rectification. Molecular dynamics simulations of a nanopore in a hBN–graphene–hBN stack reveal confinement and surface charge-dependent suppression of the relative permittivity of interfacial water. Continuum modeling with radially varying interfacial water permittivity reproduces the asymmetric I–V characteristics and explains how the embedded gate sculpts local potential and ion concentrations. By enabling sub-0.5 V control of ionic transport at up to 100 mM salt concentrations, these devices address a key need in nanofluidics to create low-power ionic circuits and biosensing.

Materials science↗
DOE OSTI2021

A High-Frequency Planar Transformer with Medium-Voltage Isolation: Preprint

This paper presents the design of a low-loss, high-frequency planar transformer having medium-voltage (10's of kV) isolation capability while transformer primary and secondary windings are interleaved to reduce losses. Medium-voltage isolation between adjacent printed circuit board (PCB) layers is extremely challenging using traditional PCB dielectrics. The isolation requirement is met using PCB with $7$\,kV/mil polyimide (Panasonic Felios RF775) as the dielectric, and by an appropriate layout of the windings and the inter-winding vias. The transformer is used to implement a dual active bridge (DAB) converter in a stackable dc-ac architecture where the dc port is connected to a photovoltaic (PV) string and ac outputs are connected in series to achieve direct PV string-to-medium voltage conversion without the need for low-voltage collection or a bulky line frequency transformer. Since each DAB transformer processes time-varying power, a design methodology is developed to minimize line-cycle-averaged losses. Experimental results are presented for a 1:1 planar transformer in a 7.5\,kW SiC-based dc-to-ac module operating at 200 kHz. Isolation of 26 kV between the primary and secondary layers and between the windings and the core is verified using a hipot tester.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2021

Ultrathin platinum nanowire based electrodes for high-efficiency hydrogen generation in practical electrolyzer cells

Significant reduction of noble metal catalyst loading and simplification of electrode fabrication are urgently needed in order to lower the cost of proton exchange membrane electrolyzer cells (PEMECs) for large-scale hydrogen production. Herein, we report an integrated electrode design comprising in-situ grown platinum nanowires (PtNW) on ultrathin titanium liquid/gas diffusion layers (LGDLs) via a cost-effective and green chemical synthesis approach. The ultrathin integrated PtNW electrodes showed a low cell voltage of 1.643 V and high efficiency of 90.08% at 1000 mA cm -2 using about 15 times lower catalyst loadings than a conventional catalyst-coated membrane in PEMEC tests. Ex-situ electrochemical characterizations and microscale visualizations further reveal that PtNW electrodes display highly efficient hydrogen evolution reactions and excellent electrode durability due to high active surface area, favorable bubble detachment, and structural stability. This work provides new insights into catalyst layer design and facile ultrathin electrode fabrication for more compact and low-cost PEM electrolyzers, fuel cells and other systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Case Study: Field Evaluation of a Low-Cost Circuit-Level Electrical Submetering System

Circuit-level metering technologies provide the ability to monitor individual circuits within an electrical panel in a building, providing detailed power and energy consumption data at a much more granular level than was previously achievable in a cost-effective manner. While the fundamental hardware components of circuit-level—split-core current transformers (CTs) and power monitoring meters—have existed for some time, the new offerings in the market have tightly integrated these components, lower costs, and have streamlined data organization, transport, and access via software solutions accessible through web and application programming interfaces (API). NREL evaluated Meazon’s single-circuit metering system. The evaluation of the equipment under test (EUT) focused on three aspects: (1) accuracy of the data provided by the system, (2) ease of installation of this technology and ease of data integration into existing U.S. General Services Administration (GSA) analytics platforms, and (3) total cost of ownership and cost-effectiveness of the technology. The metering technology was tested in a field deployment where it was installed in low and high-voltage commercial electrical panels in the César E. Chávez Memorial Building in Denver, Colorado. The goals were to assess the metering accuracy, the ease of installation and data retrieval, and the total cost of ownership and cost-effectiveness. This technology proved easy to install by a certified electrician who completed the install of 6 meters in 2 separate panels (120/208 V and 277/480 V) and 2 circuit disconnects (along with associated commissioning) at the César E. Chávez Memorial Building in less than one day. The technology was installed in high- and low-voltage panels and with limited space in the electrical room, demonstrating the applicability of this technology to almost all commercial buildings in the GSA portfolio. Primary considerations for this technology include appropriate sizing of CTs for each circuit, selection of loads/circuits/panels that are of high value for detailed submetering (e.g., tailored for high-load devices), and how GSA would like to integrate these data with its existing energy management infrastructure. Through the field evaluation, we demonstrated data integration from the vendor system into the primary software component on the GSA enterprise-level energy management and information system, GSA Link. Data from the circuit-level metering were integrated into this platform and used to perform FDD. This demonstrated the ability of the EUT to augment existing energy management and information systems in buildings where GSA Link is deployed and provides a pathway for delivering FDD at other buildings throughout the portfolio.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Electro-Chemo-Mechanical Evolution at the Garnet Solid Electrolyte–Cathode Interface

Solid-state batteries promise higher energy density and improved safety compared with lithium-ion batteries. However, electro-chemomechanical instabilities at the solid electrolyte interface with the cathode and the anode hinder their large scale implementation. Here, in this study, we focus on resolving electro-chemo-mechanical instability mechanisms and their onset conditions between a state-of-the-art cathode, LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), and the garnet Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte. We used thin-film NMC622 on LLZO pellets to place the interfacial region within the detection depth of the X-ray characterization techniques. The experimental probes of the near-interface region included in operando X-ray absorption spectroscopy and ex situ focused ion beam scanning electron microscopy. Electrochemical degradation was not observable during cycling at room temperature with 4.3 V versus Li/Li + charge voltage cutoff, or with stepwise potentiostatic hold up to 4.1 V versus Li/Li + . In contrast, secondary phases including reduced transition metal species (Ni 2+ , Co 2+ ) were found after cycling up to 4.3 V versus Li/Li + at 80 °C and during potentiostatic hold at 4.3 V versus Li/Li + (Ni 2+ ). Intergranular cracks between NMC622 grains and delamination at the NMC622|LLZO interface occurred readily after the first charge. These interface reaction products and mechanical failure lowered the capacity and cell efficiency due to partial loss of the NMC622 phase, partial loss of contact at the interface, and a higher polarization resistance. Electrochemical instability between delithiated NMC622 and LLZO could be mitigated by using a low charge voltage cutoff or cycling at lower temperature. Ways to engineer the mechanical properties to avoid crack deflection and delamination at the interface are also discussed for enhancing mechanical stability.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Forming Interphase Microgrids in Distribution Systems Using Cooperative Inverters

Interphase-microgrids formed by three islanded single-phase feeders in distribution systems are proposed in this paper. Loss of utility caused by natural and human-made disasters may isolate each residential subdivision from the utility. In this case, the household loads are supplied by distributed generation (DG) units which may not be enough to meet the load demand. This can lead to deviations in voltage and frequency, and the deviations may vary for each phase. The proposed solution is to form an interphase-microgrid by seamlessly interconnecting the islanded single-phase feeders. This interphase-microgrid can effectively balance the load demands and DG generation in distribution systems after losing the utility supply. This paper presents different case studies to demonstrate the viability of forming interphase-microgrids for residential distribution systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Assembly of Close–Packed Ferroelectric Polymer Nanowires via Interface–Epitaxy with ReS 2

The flexible, transparent, and low-weight nature of ferroelectric polymers makes them promising for wearable electronic and optical applications. To reach the full potential of the polarization-enabled device functionalities, large-scale fabrication of polymer thin films with well-controlled polar directions is called for, which remains a central challenge. The widely exploited Langmuir–Blodgett, spin-coating, and electrospinning methods only yield polymorphous or polycrystalline films, where the net polarization is compromised. Here, an easily scalable approach is reported to achieve poly(vinylidene fluoride-trifluoroethylene) P(VDF-TrFE) thin films composed of close-packed crystalline nanowires via interface-epitaxy with 1T'-ReS 2 . Upon controlled thermal treatment, uniform P(VDF-TrFE) films restructure into about 10 and 35 nm-wide (010)-oriented nanowires that are crystallographically aligned with the underlying ReS 2 , as revealed by high-resolution transmission electron microscopy. Piezoresponse force microscopy studies confirm the out-of-plane polar axis of the nanowire films and reveal coercive voltages as low as 0.1 V. Reversing the polarization can induce a conductance switching ratio of >10 8 in bilayer ReS 2 , over six orders of magnitude higher than that achieved by an untreated polymer gate. Lastly, this study points to a cost-effective route to large-scale processing of high-performance ferroelectric polymer thin films for flexible energy-efficient nanoelectronics.

crystalline nanowires↗